Name: evaluation of muscle function of the extensor digitorum longus muscle ex vivo and tibialis anterior muscle in situ in mice
Uploaded: 2013-02-09T14:00:00
Duration: 14 min 36 s
Description: Watch this Scientific Journal Video about Evaluation of Muscle Function of the Extensor Digitorum Longus Muscle Ex vivo and Tibialis Anterior Muscle In situ in Mice at JoVE.com

This work was supported by grants from the National Institutes of Health (AR-49419, DD), Muscular Dystrophy Association (DD), and NIH training grant T90DK70105 (CH).

1. Evaluation of the Contractile and Passive Properties of the EDL Muscle Ex vivo
The contractile and passive properties of the EDL muscle are measured ex vivo using the Aurora Scientific in vitro muscle test system. Refer to Table 1 for materials and equipment.
1.1 Equipment preparation
<ol>
	<li>Assemble the tissue-organ bath by securing the oxytube to the water-jacket tissue bath. Attach the assembled bath to the muscle mounting apparatus. Connect the gas line to the oxytube. Fasten the water circulation lines to the water-jacket tissue bath and place the needle valve into the bath drainage.</li>
	<li>Turn on the circulating water-bath and adjust the temperature to 30 &deg;C 7. Allow 5 PSI (pounds per square inch) of 95% O2-5% CO2 to flow through the oxytube. Fill the bath with Ringer's buffer. Equilibrate the buffer for at least 10 min with a steady gas flow by adjusting the oxytube valve.</li>
	<li>Turn on the instruments (stimulator, dual-mode lever system, and signal interface). Load the dynamic muscle control (DMC) software according to manufacturer's instruction.</li>
</ol>
1.2 EDL muscle dissection
All animal studies must be approved by the Institutional Animal Care and Use Committee.
<ol>
	<li>Anesthetize the mouse with intraperitoneal injection of 2.5 &mu;l/g body weight of the anesthetic cocktail (refer to materials section). Throughout the surgical procedure, the depth of sedation was checked by performing a toe pinch. A supplement of 10% of the initial anesthetic dose is administrated when needed to keep the animal under anesthesia. Shave the hind limb. Maintain the body core temperature at 37 &deg;C prior to dissection procedure by placing the mouse on a heating pad. The body temperature is monitored by constantly measuring the rectal temperature using a thermal probe. </li>
	<li>Position the mouse supine on the dissection board (Figure 1). Peel off the leg skin to expose the hind limb muscles. Secure the leg on the sylgard block using two dressmaker pins, one in the foot and the other in the gracilis muscle. Place a heat lamp above the mouse body to maintain the core body temperature at 37 &deg;C. Constantly superfuse all exposed muscles with Ringer's buffer. Drain excess buffer through a vacuum line.</li>
	<li>Expose the distal TA tendon and the extensor ligament under a stereomicroscope by dissecting the skin toward the foot. Gently remove the fascia covering the TA muscle. Cut the extensor ligament to release the distal TA tendon.</li>
	<li>Cut the distal TA tendon and use it to peel off the TA muscle. Carefully remove the TA muscle at its proximal attachment. Place a thin piece of Ringer's buffer soaked cotton next to the EDL muscle to absorb bleeding caused by the rupture of the TA muscle vasculature. Use the vacuum line to remove excess buffer and blood.</li>
	<li>Tie a double square knots followed by a loop knot using a bread silk suture at the muscle tendon junction (MTJ) of the distal EDL muscle (Figure 2). Make an incision in the distal portion of the biceps femoris muscle to expose the proximal EDL muscle. Repeat the same set of knots (Figure 2) at the MTJ of the proximal EDL tendon. Attach the lever arm hook to either the proximal or the distal knots with a double square knot using the same suture line. Cut off the remaining suture line.</li>
	<li>Cut the proximal EDL tendon superior to the proximal suture knot. Lift up the EDL muscle with the hook and cut the vasculature beneath the muscle. Cut the distal EDL tendon inferior to the distal suture knot to remove the EDL muscle from the hind limb. Cover the exposed hind limb with a piece of Ringer's buffer soaked cotton.</li>
	<li>Attach the hook to the lever arm. Align the muscle vertically between two electrodes. Secure the distal suture line to the fixed post. Lift up the tissue bath to submerge the muscle in Ringer's buffer. Adjust the resting tension to 1.0 g using the dual coarse/fine translation stage and allow the muscle to equilibrate for at least 10 min.</li>
</ol>
1.3 Measuring the contractile and passive properties of the EDL muscle
Use Table 2 to set up the parameters in the DMC software for each of the following measurements. Analyze the data using the dynamic muscle analysis (DMA) software.
1.3.1 Measuring the contractile properties of the EDL muscle
<ol>
	<li>Stimulate the EDL muscle three times at 150 Hz with 60 sec apart to stabilize the muscle 8.</li>
	<li>Stimulate the EDL muscle at different resting tensions to determine the optimal length (Lo). The optimal length is the length at which muscle develops maximum twitch tension. Allow the muscle to relax for 2 min.</li>
	<li>Adjust the resting tension to Lo. Measure muscle force at single twitch stimulation. Determine the absolute twitch force (Pt), time to peak tension (TPT) and half relaxation time (&frac12; RT) of the Pt. Allow the muscle to relax for 2 min.</li>
	<li>Adjust the resting tension to Lo. Measure tetanic muscle force generated at different stimulation frequencies (50, 80, 100, 120, 150 and 200 Hz). Determine the absolute maximal tetanic muscle force (Po) where muscle force reaches the maximal. Measure the TPT and &frac12; RT of the Po 9.</li>
	<li>Allow the muscle to relax for 5 min. Adjust the resting tension to Lo. Apply 10 cycles of eccentric contractions with 2 min rest between cycles. Calculate the relative force loss of the Po after each cycle of eccentric contraction.</li>
	<li>Detach the EDL muscle from the apparatus and cut the tendons at the suture site. Determine the muscle wet weight and calculate the muscle cross sectional area (CSA) 6,10.</li>
</ol>
1.3.2 Measuring the passive properties of the EDL muscle
<ol>
	<li>Dissect the contralateral EDL muscle and attach it to the apparatus as described in Section 1.2, steps 2 to 7.</li>
	<li>Subject the EDL muscle to a six-step stretching protocol where the muscle is strained to 160% Lo with an increment of 10% Lo. Analyze the stress-strain profile 6.</li>
	<li>Evaluate the viscous property of the EDL muscle by measuring the stress relaxation rate (SRR) at the following time frames after stretching and holding the muscle at 10% Lo: from peak to 0.1s post-peak (pp), from 0.1 to 0.2s pp, from 0.2 to 0.5s pp, from 0.5 to 1s pp and from 1 to 1.5s pp.</li>
	<li>At the end of study, euthanize the mouse by cervical dislocation and/or decapitation while the mouse is still under anesthesia. Detach the EDL muscle from the apparatus and cut the tendons at the suture site. Determine the muscle wet weight and calculate the muscle cross sectional area (CSA) 6,10.</li>
</ol>
2. Evaluation of the Contractile Properties of the TA Muscle In situ
The contractile properties of the TA muscle are measured using the Aurora Scientific in situ muscle test system. Refer to Table 1 for materials and equipment.
2.1 Equipment preparation
<ol>
	<li>Heat up the thermo-controlled animal stage to 37 &deg;C using the circulating water-bath.</li>
	<li>Turn on the instruments (stimulator, dual-mode lever system, and signal interface). Load the DMC software according to manufacturer's instruction.</li>
</ol>
2.2 Preparation of the TA muscle for in situ force measurement
<ol>
	<li>Anesthetize the mouse, shave the hind limb and expose the TA muscle as described in steps 1 to 3 in Section 1.2.</li>
	<li>Tie a double square knot around the patella ligament using a bread silk suture. Tie a double square knot followed by a loop knot at the MTJ of the distal TA muscle (Figure 2), tie another double square knot leaving a ~10 mm loop from the distal TA tendon knot using the same suture line. Place the second double square knot on the side of the loop.</li>
	<li>Remove the pins from the hind limb and position the animal prone. Expose the biceps femoris muscle. Make an incision in the midline to reveal the sciatic nerve. Tie a double square knot around the proximal end of the sciatic nerve. Trim one side of the suture lines and cut the nerve superior to the knot. Gently, pull the sciatic nerve toward the knee using the suture line and clear the surrounding connective tissue to free ~ 5 mm of its length. Do not stretch the nerve during this procedure and constantly superfuse the nerve with ringer buffer.</li>
	<li>Prepare the contralateral TA muscle as described in steps 1 to 3. Cover one of the exposed hind limb with a piece of Ringer's buffer soaked cotton. Constantly superfuse both hind limbs with pre-warmed (37 &deg;C) Ringer's buffer. Remove excess buffer through a vacuum line.</li>
	<li>Position the animal prone on the animal platform. Attach the knee clamp holder to the animal platform and secure both knees to the metal pin with double square knots using the patella ligament suture lines. Pin both feet on the sylgard block using dressmaker pins. Secure the animal platform onto the thermo-controlled stage. Position the heat lamp to maintain the animal core body temperature at 37 &deg;C.</li>
	<li>Secure the electrode holder to the animal platform and lay the sciatic nerve on the electrode using the suture line. Keep the electrode away from the hind limb muscles. Cut the distal TA tendon of the uncovered hind limb at the MTJ suture site. Attach the distal TA tendon suture loop to the lever arm hook. Cover the exposed hind limb muscle with a warm Ringer's buffer soaked cotton.</li>
</ol>
2.3 Measuring the contractile properties of the TA muscle
<ol>
	<li>Use Table 2 to set the parameters in the DMC software. Follow the same protocol described in Section 1.3.1 to determine the contractile properties of the TA muscle. Analyze the data using the DMA software.</li>
	<li>After contractile property measurement, detach the distal TA tendon suture loop from the leveler arm hook. Remove the TA muscle. Determine the muscle wet weight and calculate the CSA 10.</li>
	<li>Measure the contractile properties of the contralateral TA muscle according to steps 1 to 3 described above. Euthanize the mouse according to institutional guidelines at the end of the study.</li>
</ol>

<ol>
	<li>Huijing, P. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Muscle+as+a+collagen+fiber+reinforced+composite:+a+review+of+force+transmission+in+muscle+and+whole+limb.">Muscle as a collagen fiber reinforced composite: a review of force transmission in muscle and whole limb.</a> J. Biomech. 32, 329-345 (1999).</li><li>Moss, R. L., Halpern, W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Elastic+and+viscous+properties+of+resting+frog+skeletal+muscle.">Elastic and viscous properties of resting frog skeletal muscle.</a> Biophys. J. 17, 213-228 (1977).</li><li>Hoffman, E. P., Brown, R. H., Kunkel, L. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Dystrophin:+the+protein+product+of+the+Duchenne+muscular+dystrophy+locus.">Dystrophin: the protein product of the Duchenne muscular dystrophy locus.</a> Cell. 51, 919-928 (1987).</li><li>Petrof, B. J., Shrager, J. B., Stedman, H. H., Kelly, A. M., Sweeney, H. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Dystrophin+protects+the+sarcolemma+from+stresses+developed+during+muscle+contraction.">Dystrophin protects the sarcolemma from stresses developed during muscle contraction.</a> Proc. Natl. Acad. Sci. U.S.A. 90, 3710-3714 (1993).</li><li>Pastoret, C., Sebille, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=mdx+mice+show+progressive+weakness+and+muscle+deterioration+with+age.">mdx mice show progressive weakness and muscle deterioration with age.</a> J. Neurol. Sci. 129, 97-105 (1995).</li><li>Hakim, C. H., Grange, R. W., Duan, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+passive+mechanical+properties+of+the+extensor+digitorum+longus+muscle+are+compromised+in+2-+to+20-mo-old+mdx+mice.">The passive mechanical properties of the extensor digitorum longus muscle are compromised in 2- to 20-mo-old mdx mice.</a> J. Appl. Physiol. 110, 1656-1663 (2011).</li><li>Segal, S. S., Faulkner, J. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Temperature-dependent+physiological+stability+of+rat+skeletal+muscle+in+vitro.">Temperature-dependent physiological stability of rat skeletal muscle in vitro.</a> Am. J. Physiol. 248, 265-270 (1985).</li><li>Grange, R. W., Gainer, T. G., Marschner, K. M., Talmadge, R. J., Stull, J. T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Fast-twitch+skeletal+muscles+of+dystrophic+mouse+pups+are+resistant+to+injury+from+acute+mechanical+stress.">Fast-twitch skeletal muscles of dystrophic mouse pups are resistant to injury from acute mechanical stress.</a> Am. J. Physiol. Cell Physiol. 283, 1090-1101 (2002).</li><li>Hakim, C. H., Duan, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Gender+differences+in+contractile+and+passive+properties+of+mdx+extensor+digitorum+longus+muscle.">Gender differences in contractile and passive properties of mdx extensor digitorum longus muscle.</a> Muscle Nerve. 45, 250-256 (2012).</li><li>Hakim, C. H., Li, D., Duan, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Monitoring+murine+skeletal+muscle+function+for+muscle+gene+therapy.">Monitoring murine skeletal muscle function for muscle gene therapy.</a> Methods Mol. Biol. 709, 75-89 (2011).</li></ol>

Open access fees have been paid for by Aurora Scientific.

In this protocol, we have illustrated physiological assays for measuring the contractile and passive properties the EDL muscle and the contractile properties of the TA muscle. A major concern in muscle physiology studies is the oxygenation of the target muscle. For large muscles (such as the TA muscle), the in situ approach is preferred because oxygen diffusion from Ringer's buffer may not reach the center of the muscle in an in vitro assay. In situ approach does not disturb normal blood supply and hypoxia-associated artificial effects are avoided. The EDL muscle is one of the most commonly used muscle in physiology study. Adequate oxygenation of the entire muscle can be achieved in an in vitro system because of the small size of the muscle. Further, the in vitro system provides an enclosed environment to manipulate the concentrations of ions (Ca 2+, Na+ and K+) and chemicals (ATP and glucose) that are necessary for optimal muscle force generation. This offers a great opportunity to study the effect of these variables on force production.
Accurate measurement of the contractile and passive properties of the limb muscle is critical to study skeletal muscle function. Characteristic changes of these properties are often considered as the hallmarks of various muscle diseases. Changes in these parameters are also important indicators to determine whether an experimental therapy is effective or not.

<table border="1">
 <tbody>
 <tr>
 <td>Material</td>
 <td>Manufacturer</td>
 <td></td>
 <td>Specifications and comments</td>
 </tr>
 <tr>
 <td>Tissue-organ bath </td>
 <td>Radnoti LLC, CA, USA</td>
 <td></td>
 <td>Water-jacket tissue bath (Cat #158351-LL), Oxygen disperser tube (Cat #160192), Luer valve (Cat#120722)</td>
 </tr>
 <tr>
 <td>Circulating water bath </td>
 <td>Fisher Scientific, Waltham, MA, USA</td>
 <td></td>
 <td></td>
 </tr>
 <tr>
 <td>Gas mix </td>
 <td>Airgas National, Charlotte, NC, USA</td>
 <td></td>
 <td>95% O2 and 5% CO2 </td>
 </tr>
 <tr>
 <td>In vitro muscle function assay apparatus </td>
 <td>Aurora Scientific, Aurora, ON, Canada</td>
 <td></td>
 <td>The system consists of a stimulator (Model# 701A), a dual-mode lever system (Model#300C or 305C), a signal interface (Model # 604B) and a test apparatus (Model# 800A) to vertically mount tissue organ bath</td>
 </tr>
 <tr>
 <td>In vitro muscle function assay software</td>
 <td></td>
 <td></td>
 <td>Dynamic muscle control (DMC) software and dynamic muscle control data analysis (DMA) software</td>
 </tr>
 <tr>
 <td>Mouse anesthesia cocktail mixed in 0.9% NaCl</td>
 <td>Refer to the institutional guidelines</td>
 <td></td>
 <td>Ketamine (25 mg/ml), xylazine (2.5 mg/ml) and acepromazine (0.5 mg/ml). Throughout the surgical procedure, a supplement of 10 % of the initial dose may be needed to keep animal under anesthesia. </td>
 </tr>
 <tr>
 <td>Sylgard</td>
 <td>World Precision Instrument</td>
 <td>Cat#SYLG184</td>
 <td></td>
 </tr>
 <tr>
 <td>A custom-made Plexiglas dissection board</td>
 <td>In house designed</td>
 <td></td>
 <td>Refer to Figure 1</td>
 </tr>
 <tr>
 <td>Heating lamp </td>
 <td>Tensor Lighting Company, Boston, MA, USA</td>
 <td></td>
 <td>15 Watt lamp to keep the mouse warm during dissection</td>
 </tr>
 <tr>
 <td>Ringer's Buffer </td>
 <td>Chemicals are purchased from Fisher Scientific, Waltham, MA, USA</td>
 <td></td>
 <td>Composition in mM: 1.2 NaH2PO4 (Cat#S369) , 1 MgSO4 (Cat# M63), 4.83 KCl (Cat# P217), 137 NaCl (Cat# 217), 24 NaHCO3 (Cat# S233), 2 CaCl2 (Cat #C79) and 10 glucose (Cat# D16). Dissolve chemicals individually and mix in the order listed above. Store at 4 &deg;C.</td>
 </tr>
 <tr>
 <td>Stereo dissecting microscope </td>
 <td>Nikon, Melville, NY, USA</td>
 <td></td>
 <td></td>
 </tr>
 <tr>
 <td>Dissection tools </td>
 <td>Fine Science Tools, Foster City, CA, USA</td>
 <td></td>
 <td>Coarse forceps, coarse scissors, fine forceps (Straight and 45 &deg; angle)</td>
 </tr>
 <tr>
 <td>Braided silk suture #4-0 </td>
 <td>SofSilk USSC Sutures, Norwalk, CT, USA</td>
 <td>Cat # SP116</td>
 <td></td>
 </tr>
 <tr>
 <td>A custom-made stainless steel hook</td>
 <td>Small Parts, Inc. </td>
 <td></td>
 <td>2'' long S/S 304V (0.18'' diameter) for force transducer 305C or 2.5'' long S/S 304V (0.012'' diameter) for transducer 300C (Cat# ASTM A313) </td>
 </tr>
 <tr>
 <td>In situ muscle function assay system </td>
 <td>Aurora Scientific, Aurora, ON, Canada</td>
 <td></td>
 <td>The system (809B, in situ mouse apparatus) consist of a stimulator (Model# 701B), a dual-mode lever system (Model# 305C), a signal interface (Model# 604A) and a thermo controlled footplate apparatus (Model# 809A)</td>
 </tr>
 <tr>
 <td>In vitro muscle function assay software</td>
 <td>Aurora Scientific, Aurora, ON, Canada</td>
 <td></td>
 <td>Dynamic muscle control (DMC) software and dynamic muscle control data analysis (DMA) software</td>
 </tr>
 <tr>
 <td>A custom-made TA assay animal platform</td>
 <td>In house designed</td>
 <td></td>
 <td>Refer to Figure 2</td>
 </tr>
 <tr>
 <td>A custom-made stainless steel hook</td>
 <td>Small Parts, Inc. </td>
 <td>Cat# ASTM A313</td>
 <td>0.5'' long S/S 304V (0.18'' diameter) </td>
 </tr>
 <tr>
 <td>Custom-made 25G platinum electrodes</td>
 <td>Chalgren Enterprises, Gilroy,CA</td>
 <td></td>
 <td>Solder two 0.016'' thick platinum wires to two 24G electric wires</td>
 </tr>
 </tbody>
</table>
Table 1. Materials and equipment.

evaluation of muscle function of the extensor digitorum longus muscle ex vivo and tibialis anterior muscle in situ in mice

Body movements are mainly provided by mechanical function of skeletal muscle. Skeletal muscle is composed of numerous bundles of myofibers that are sheathed by intramuscular connective tissues. Each myofiber contains many myofibrils that run longitudinally along the length of the myofiber. Myofibrils are the contractile apparatus of muscle and they are composed of repeated contractile units known as sarcomeres. A sarcomere unit contains actin and myosin filaments that are spaced by the Z discs and titin protein. Mechanical function of skeletal muscle is defined by the contractile and passive properties of muscle. The contractile properties are used to characterize the amount of force generated during muscle contraction, time of force generation and time of muscle relaxation. Any factor that affects muscle contraction (such as interaction between actin and myosin filaments, homeostasis of calcium, ATP/ADP ratio, etc.) influences the contractile properties. The passive properties refer to the elastic and viscous properties (stiffness and viscosity) of the muscle in the absence of contraction. These properties are determined by the extracellular and the intracellular structural components (such as titin) and connective tissues (mainly collagen) 1-2. The contractile and passive properties are two inseparable aspects of muscle function. For example, elbow flexion is accomplished by contraction of muscles in the anterior compartment of the upper arm and passive stretch of muscles in the posterior compartment of the upper arm. To truly understand muscle function, both contractile and passive properties should be studied.
The contractile and/or passive mechanical properties of muscle are often compromised in muscle diseases. A good example is Duchenne muscular dystrophy (DMD), a severe muscle wasting disease caused by dystrophin deficiency 3. Dystrophin is a cytoskeletal protein that stabilizes the muscle cell membrane (sarcolemma) during muscle contraction 4. In the absence of dystrophin, the sarcolemma is damaged by the shearing force generated during force transmission. This membrane tearing initiates a chain reaction which leads to muscle cell death and loss of contractile machinery. As a consequence, muscle force is reduced and dead myofibers are replaced by fibrotic tissues 5. This later change increases muscle stiffness 6. Accurate measurement of these changes provides important guide to evaluate disease progression and to determine therapeutic efficacy of novel gene/cell/pharmacological interventions. Here, we present two methods to evaluate both contractile and passive mechanical properties of the extensor digitorum longus (EDL) muscle and the contractile properties of the tibialis anterior (TA) muscle.

The following results are a representation from our previous reports 6,9. Data are presented as mean&plusmn;standard error of mean. Table 3 shows the morphometric properties of the EDL muscle in normal BL10 and dystrophin-deficient (mdx) mice at 4 to 6 months of age. Figure 4 shows representative contractile and passive properties of the EDL muscle from BL10 and mdx mice. The contractile properties of the EDL muscle are described by the following terms including the specific (absolute force divided by the CSA) twitch force (Figure 4A), specific maximal tetanic force (Figure 4B), TPT and &frac12; RT of the absolute maximal tetanic force (Figure 4C and D). The TPT and &frac12; RT can also be calculate from the absolute twitch force. The stress-strain profile (Figure 4E) and SRR (Figure 4F) are used to describe the passive properties of the EDL muscle.
Absence of dystrophin has a significant impact on the contractile and passive properties of the EDL muscle 6,9. Specific twitch and tetanic forces are significantly reduced in the mdx EDL muscle. The TPT is significantly faster while the &frac12; RT is significantly slower in the mdx EDL muscle. The stress-strain profile suggests that stiffness is significantly increased in the mdx EDL muscle. The mdx EDL muscle also yields a significantly much higher resistance force (passive stress) before reaching the peak stress, while the post-peak stresses decline much faster. Further, the SRR was significantly higher in the mdx EDL muscle compared to that of the BL10 EDL muscle.
Statistical analysis
Statistical significance between two groups is analyzed by the Student t-test. For statistical significance among multiple groups, One-way or Two-way ANOVA analysis followed by Bonferroni post hoc analysis is recommended using the SAS software (SAS Institute Inc., Cary, NC). Difference is considered significant when p &lt; 0.05.
Table 1. Materials and equipment. 
<table border="1">
 <tbody>
 <tr>
 <td class="jove_content_small">Experiment</td>
 <td class="jove_content_small">Resting tension (gram)</td>
 <td class="jove_content_small">Pulse frequency (Hz) </td>
 <td class="jove_content_small">Pulse width (ms)</td>
 <td class="jove_content_small">Stimulation duration (ms)</td>
 <td class="jove_content_small">Stretch length </td>
 <td class="jove_content_small">Stretch duration (ms) </td>
 <td class="jove_content_small">Stretch rate </td>
 <td class="jove_content_small">Comments</td>
 </tr>
 <tr>
 <td colspan="9">1. Evaluation of contractile and passive properties of the EDL muscle ex vivo</td>
 </tr>
 <tr>
 <td colspan="9">1.3.1 Measuring the contractile properties of the EDL muscle </td>
 </tr>
 <tr>
 <td>1. Warm up</td>
 <td>1.0</td>
 <td>150</td>
 <td>0.2</td>
 <td>300</td>
 <td></td>
 <td></td>
 <td></td>
 <td>Rest the muscle for 60 sec between each stimulus. These preliminary tetanic contractions stabilize the muscle for subsequent measurements.</td>
 </tr>
 <tr>
 <td>2. Optimal muscle length (Lo)</td>
 <td>0.5, 1.0, 1.5 and 2.0</td>
 <td>1</td>
 <td>0.2</td>
 <td>300</td>
 <td></td>
 <td></td>
 <td></td>
 <td>Allow the muscle to relax for 30 sec between each stimulus. Measure the muscle optimal length using a digital caliper.</td>
 </tr>
 <tr>
 <td>3. Single twitch force (Pt)</td>
 <td>Adjust resting tension to Lo</td>
 <td>1</td>
 <td>0.2</td>
 <td>300</td>
 <td></td>
 <td></td>
 <td></td>
 <td></td>
 </tr>
 <tr>
 <td>4. Tetanic muscle force </td>
 <td>Adjust resting tension to Lo</td>
 <td>50, 80, 100, 120, 150 and 200 </td>
 <td>0.2</td>
 <td>300</td>
 <td></td>
 <td></td>
 <td></td>
 <td>Allow the muscle to relax for 1 min between each stimulus. Determine the frequency that generate the maximal absolute tetanic force (Po).</td>
 </tr>
 <tr>
 <td>5. Eccentric contraction</td>
 <td>Adjust resting tension to Lo</td>
 <td>Use the frequency that generates the maximum tetanic force (Po) </td>
 <td>0.2</td>
 <td>700</td>
 <td>10% Lo</td>
 <td>last 200 ms of the stimulation duration</td>
 <td>0.5 Lo/sec</td>
 <td>Repeat the eccentric contraction for 10 cycles with 2 min rest between cycles.</td>
 </tr>
 <tr>
 <td>6. CSA of the EDL muscle </td>
 <td></td>
 <td></td>
 <td></td>
 <td></td>
 <td></td>
 <td></td>
 <td></td>
 <td>CSA = (muscle mass (g) / [1.06 g/cm3 x (Lo x 0.44)]. 1.06 g/cm3 is the muscle density and 0.44 is the EDL muscle fiber length to Lo ratio. </td>
 </tr>
 <tr>
 <td colspan="9">1.3.2 Measuring the passive properties of the EDL muscle </td>
 </tr>
 <tr>
 <td>1. Six-step stretching protocol</td>
 <td>Adjust resting tension to Lo</td>
 <td></td>
 <td></td>
 <td></td>
 <td>10% Lo</td>
 <td></td>
 <td>2 cm/sec</td>
 <td>Repeat the stretching protocol with an increment of 10% Lo till 160% Lo is reached. Alow 1.5 sec between stretch cycles.</td>
 </tr>
 <tr>
 <td>2. SRR</td>
 <td>Adjust resting tension to Lo</td>
 <td></td>
 <td></td>
 <td></td>
 <td>10% Lo</td>
 <td></td>
 <td>2 cm/sec</td>
 <td>SSR is calculated by dividing the difference in the stress with the time elapsed between two time points in a time frame. </td>
 </tr>
 <tr>
 <td colspan="9">2.3 Measuring the contractile properties of the TA muscle </td>
 </tr>
 <tr>
 <td>1. Warm up</td>
 <td>4.0</td>
 <td>150</td>
 <td>0.2</td>
 <td>300</td>
 <td></td>
 <td></td>
 <td></td>
 <td>Rest the muscle for 60 sec between each stimulus. </td>
 </tr>
 <tr>
 <td>2. Optimal muscle length (Lo)</td>
 <td>3.0, 4.0, 5.0, 6.0 and 7.0</td>
 <td>1</td>
 <td>0.2</td>
 <td>300</td>
 <td></td>
 <td></td>
 <td></td>
 <td>Allow the muscle to relax for 30 sec between each stimulus. Measure the muscle optimal length using a digital caliper.</td>
 </tr>
 <tr>
 <td>3. CSA of the TA muscle </td>
 <td></td>
 <td></td>
 <td></td>
 <td></td>
 <td></td>
 <td></td>
 <td></td>
 <td>CSA = (muscle mass (g) / [1.06 g/cm3 x (Lo x 0.6)]. 0.6 is the TA muscle fiber length to Lo ratio. </td>
 </tr>
 </tbody>
</table>
Table 2. Parameters for the evaluation of the mechanical properties of the EDL and TA muscles.
<table border="1">
 <tbody>
 <tr>
 <td>Strain </td>
 <td>Age (month) </td>
 <td>Body weight (g)</td>
 <td>EDL weight (mg)</td>
 <td>EDL Lo (mm)</td>
 <td>EDL CSA (mm2)</td>
 </tr>
 <tr>
 <td>BL10</td>
 <td>6</td>
 <td>32.03 &plusmn; 0.57</td>
 <td>13.90 &plusmn; 0.77</td>
 <td>14.09 &plusmn; 0.04</td>
 <td>2.12 &plusmn; 0.12</td>
 </tr>
 <tr>
 <td>mdx</td>
 <td>6</td>
 <td>35.44 &plusmn; 0.42*</td>
 <td>16.73 &plusmn; 0.42*</td>
 <td>13.93 &plusmn; 0.05*</td>
 <td>2.57 &plusmn; 0.07*</td>
 </tr>
 </tbody>
</table>
Table 3. Morphometric properties of the EDL muscle. *, the value in mdx mice is significantly different from that of age-matched BL10 mice.
<img src="/files/ftp_upload/50183/50183fig1.jpg" alt="Figure 1" fo:src="/files/ftp_upload/50183/50183fig1highres.jpg" fo:content-width="5.5in"/> 
 Figure 1. A schematic diagram of the custom-made mouse dissection board. The dissection board is made from a &frac12; inch thick plexiglass and was fabricated at the institutional shop. <a href="https://www.jove.com/files/ftp_upload/50183/50183fig1large.jpg" target="_blank">Click here to view larger figure</a>.
<img src="/files/ftp_upload/50183/50183fig2.jpg" alt="Figure 2" fo:src="/files/ftp_upload/50183/50183fig2highres.jpg" fo:content-width="4in"/>/> 
 Figure 2. A series of digital images showing the steps of tying a double square knot followed by a loop knot at the MTJ. Asterisk, the EDL muscle; Arrow, the distal tendon of the EDL muscle.
<img src="/files/ftp_upload/50183/50183fig3.jpg" alt="Figure 3" fo:src="/files/ftp_upload/50183/50183fig3highres.jpg" fo:content-width="6in"/>/> 
 Figure 3. A schematic diagram of the custom-made platform for in situ TA muscle function assay. The plexiglass animal platform and the stainless steel knee holder were designed to mount on the 809B in situ mouse apparatus. *, Stainless steel rod (Cat# MPR-2.0, Siskiyou, Grants Pass, OR); #, Universal electrode holder (Cat# MXB, Siskiyou, Grants Pass, OR); &sect;, electrode attachment rod (Cat# MPR-3.0, Siskiyou, Grants Pass, OR); **, Sylgard block. <a href="https://www.jove.com/files/ftp_upload/50183/50183fig3large.jpg" target="_blank">Click here to view larger figure</a>.
<img src="/files/ftp_upload/50183/50183fig4.jpg" alt="Figure 4" fo:src="/files/ftp_upload/50183/50183fig4highres.jpg" fo:content-width="4in"/>/> 
 Figure 4. Representative results for the contractile and passive properties of the EDL muscle. The contractile properties of the EDL muscle are characterized by the specific twitch force (A), the specific tetanic force (B), the time to peak tension (C) and the half relaxation time (D). The passive properties of the EDL muscle are assessed by the stress strain profile (E) and the SSR. *, mdx mice are significantly different from age-matched BL10 mice.

Watch this Scientific Journal Video about Evaluation of Muscle Function of the Extensor Digitorum Longus Muscle Ex vivo and Tibialis Anterior Muscle In situ in Mice at JoVE.com

Evaluation of Muscle Function of the Extensor Digitorum Longus Muscle Ex vivo and Tibialis Anterior Muscle In situ in Mice

Changes in limb muscle contractile and passive mechanical properties are important biomarkers for muscle diseases. This manuscript describes physiological assays to measure these properties in the murine extensor digitorum longus and tibialis anterior muscles.

Evaluation of Muscle Function of the Extensor Digitorum Longus Muscle Ex vivo and Tibialis Anterior Muscle In situ in Mice

Body  movements are mainly provided by mechanical function of skeletal muscle. Skeletal  muscle is composed of numerous bundles of myofibers that are ...

evaluation-muscle-function-extensor-digitorum-longus-muscle-ex-vivo

Research

JoVE Journal

Biology

In vivo Micro-circulation Measurement in Skeletal Muscle by Intra-vital Microscopy

BACKGROUND: Regulatory factors and detailed physiology of in vivo microcirculation have remained not fully clarified after many different modalities of imaging had invented. While many macroscopic parameters of blood flow reflect flow velocity, changes in blood flow velocity and red blood cell (RBC) flux does not hold linear relationship in the microscopic observations. There are reports of discrepancy between RBC velocity and RBC flux, RBC flux and plasma flow volume, and of spatial and temporal heterogeneity of flow regulation in the peripheral tissues in microscopic observations, a scientific basis for the requirement of more detailed studies in microcirculatory regulation using intravital microscopy. METHODS: We modified Jeff Lichtman's method of in vivo microscopic observation of mouse sternomastoid muscles. Mice are anesthetized,
ventilated, and injected with PKH26L-fluorescently labeled RBCs for microscopic observation.RESULT &amp; CONCLUSIONS: Fluorescently labeled RBCs are detected and distinguished well by a wide-field microscope. Muscle contraction evoked by electrical stimulation induced increase in RBC flux. Quantification of other parameters including RBC velocity and capillary density were feasible. Mice tolerated well the surgery, injection of stained RBCs, microscopic observation, and electrical stimulation. No muscle or blood vessel damage was observed, suggesting that our method is relatively less invasive and suited for long-term observations.

A new versatile method for observation of microcirculation is presented. It is considered suitable for long-term observation, and for combination with pharmacophysiological or molecular biological interventions.

BACKGROUND: Regulatory factors and detailed physiology of in vivo microcirculation have remained not fully clarified after many different modalities of ...

Procedures for Rat in situ Skeletal Muscle Contractile Properties

There are many circumstances where it is desirable to obtain the contractile response of skeletal muscle under physiological circumstances: normal circulation, intact whole muscle, at body temperature. This includes the study of contractile responses like posttetanic potentiation, staircase and fatigue. Furthermore, the consequences of disease, disuse, injury, training and drug treatment can be of interest. This video demonstrates appropriate procedures to set up and use this valuable muscle preparation.
To set up this preparation, the animal must be anesthetized, and the medial gastrocnemius muscle is surgically isolated, with the origin intact. Care must be taken to maintain the blood and nerve supplies. A long section of the sciatic nerve is cleared of connective tissue, and severed proximally. All branches of the distal stump that do not innervate the medial gastrocnemius muscle are severed. The distal nerve stump is inserted into a cuff lined with stainless steel stimulating wires. The calcaneus is severed, leaving a small piece of bone still attached to the Achilles tendon. Sonometric crystals and/or electrodes for electromyography can be inserted. Immobilization by metal probes in the femur and tibia prevents movement of the muscle origin. The Achilles tendon is attached to the force transducer and the loosened skin is pulled up at the sides to form a container that is filled with warmed paraffin oil. The oil distributes heat evenly and minimizes evaporative heat loss. A heat lamp is directed on the muscle, and the muscle and rat are allowed to warm up to 37&deg;C. While it is warming, maximal voltage and optimal length can be determined. These are important initial conditions for any experiment on intact whole muscle. The experiment may include determination of standard contractile properties, like the force-frequency relationship, force-length relationship, and force-velocity relationship.
With care in surgical isolation, immobilization of the origin of the muscle and alignment of the muscle-tendon unit with the force transducer, and proper data analysis, high quality measurements can be obtained with this muscle preparation.

Procedures for Rat in situ Skeletal Muscle Contractile Properties

This video demonstrates the surgical preparation and procedures needed to study the contractile responses of the rat medial gastrocnemius muscle preparation in situ. This preparation allows measurement of skeletal muscle contractile properties under physiological conditions. The animal is anesthetized and the muscle is separated from surrounding tissue at its distal end. The Achilles tendon is attached to a force transducer, allowing measurement of the muscle&#x2019;s contractile response at 37 degrees C with an intact circulation.

There are many circumstances where it is desirable to obtain the contractile response of skeletal muscle under physiological circumstances: normal ...

Ex Vivo Assessment of Contractility, Fatigability and Alternans in Isolated Skeletal Muscles

Described here is a method to measure contractility of isolated skeletal muscles. Parameters such as muscle force, muscle power, contractile kinetics, fatigability, and recovery after fatigue can be obtained to assess specific aspects of the excitation-contraction coupling (ECC) process such as excitability, contractile machinery and Ca2+ handling ability. This method removes the nerve and blood supply and focuses on the isolated skeletal muscle itself. We routinely use this method to identify genetic components that alter the contractile property of skeletal muscle though modulating Ca2+ signaling pathways. Here, we describe a newly identified skeletal muscle phenotype, i.e., mechanic alternans, as an example of the various and rich information that can be obtained using the in vitro muscle contractility assay. Combination of this assay with single cell assays, genetic approaches and biochemistry assays can provide important insights into the mechanisms of ECC in skeletal muscle.

Ex Vivo Assessment of Contractility, Fatigability and Alternans in Isolated Skeletal Muscles

We describe a method to directly measure muscle force, muscle power, contractile kinetics and fatigability of isolated skeletal muscles in an in vitro system using field stimulation. Valuable information on Ca2+ handling properties and contractile machinery of the muscle can be obtained using different stimulating protocols.

 
Described here is a method to measure contractility of isolated skeletal muscles. Parameters such as muscle force, muscle power, contractile kinetics, ...

Assessment of Calcium Sparks in Intact Skeletal Muscle Fibers

Maintaining homeostatic Ca2+ signaling is a fundamental physiological process in living cells. Ca2+ sparks are the elementary units of Ca2+ signaling in the striated muscle fibers that appear as highly localized Ca2+ release events mediated by ryanodine receptor (RyR) Ca2+ release channels on the sarcoplasmic reticulum (SR) membrane. Proper assessment of muscle Ca2+ sparks could provide information on the intracellular Ca2+&#160;handling properties of healthy and diseased striated muscles. Although Ca2+ sparks events are commonly seen in resting cardiomyocytes, they are rarely observed in resting skeletal muscle fibers; thus there is a need for methods to generate and analyze sparks in skeletal muscle fibers.
Detailed here is an experimental protocol for measuring Ca2+ sparks in isolated flexor digitorm brevis (FDB) muscle fibers using fluorescent Ca2+ indictors and laser scanning confocal microscopy. In this approach, isolated FDB fibers are exposed to transient hypoosmotic stress followed by a return to isotonic physiological solution. Under these conditions, a robust Ca2+ sparks response is detected adjacent to the sarcolemmal membrane in young healthy FDB muscle fibers. Altered Ca2+ sparks response is detected in dystrophic or aged skeletal muscle fibers. This approach has recently demonstrated that membrane-delimited signaling involving cross-talk between inositol (1,4,5)-triphosphate receptor (IP3R) and RyR contributes to Ca2+ spark activation in skeletal muscle. In summary, our studies using osmotic stress induced Ca2+ sparks showed that this intracellular response reflects a muscle signaling mechanism in physiology and aging/disease states, including mouse models of muscle dystrophy (mdx mice) or amyotrophic lateral sclerosis (ALS model).

Described here is a method to directly measure calcium sparks, the elementary units of Ca2+ release from sarcoplasmic reticulum&#160;in intact skeletal muscle fibers. This method utilizes osmotic-stress-mediated triggering of Ca2+ release from ryanodine receptor in isolated muscle fibers. The dynamics and homeostatic capacity of intracellular Ca2+ signaling can be employed to assess muscle function in health and disease.

Maintaining homeostatic Ca2+ signaling is a fundamental physiological process in living cells. Ca2+ sparks are the elementary units of Ca2+ signaling in ...

Generation of Myospheres From hESCs by Epigenetic Reprogramming

Generation of a homogeneous and abundant population of skeletal muscle cells from human embryonic stem cells (hESCs) is a requirement for cell-based therapies and for a "disease in a dish" model of human neuromuscular diseases. Major hurdles, such as low abundance and heterogeneity of the population of interest, as well as a lack of protocols for the formation of three-dimensional contractile structures, have limited the applications of stem cells for neuromuscular disorders. We have designed a protocol that overcomes these limits by ectopic introduction of defined factors in hESCs - the muscle determination factor MyoD and SWI/SNF chromatin remodeling complex component BAF60C - that are able to reprogram hESCs into skeletal muscle cells. Here we describe the protocol established to generate hESC-derived myoblasts and promote their clustering into tridimensional miniaturized structures (myospheres) that functionally mimic miniaturized skeletal muscles7.

Here, we describe a protocol based on epigenetic reprogramming of human embryonic stem cells (hESCs) toward generating a homogeneous population of skeletal muscle progenitors that under permissive culture conditions form three-dimensional clusters of contractile myofibers (myospheres), which recapitulate biological features of human skeletal muscles.

Generation of a homogeneous and abundant population of skeletal muscle cells from human embryonic stem cells (hESCs) is a requirement for cell-based ...

Detection and Analysis of DNA Damage in Mouse Skeletal Muscle In Situ Using the TUNEL Method

Terminal deoxynucleotidyl transferase (TdT) deoxyuridine triphosphate (dUTP) nick end labeling (TUNEL) is the method of using the TdT enzyme to covalently attach a tagged form of dUTP to 3&#8217; ends of double- and single-stranded DNA breaks in cells. It is a reliable and useful method to detect DNA damage and cell death in situ. This video describes dissection, tissue processing, sectioning, and fluorescence-based TUNEL labeling of mouse skeletal muscle. It also describes a method of semi-automated TUNEL signal quantitation. Inherent normal tissue features and tissue processing conditions affect the ability of the TdT enzyme to efficiently label DNA. Tissue processing may also add undesirable autofluorescence that will interfere with TUNEL signal detection. Therefore, it is important to empirically determine tissue processing and TUNEL labeling methods that will yield the optimal signal-to-noise ratio for subsequent quantitation. The fluorescence-based assay described here provides a way to exclude autofluorescent signal by digital channel subtraction. The TUNEL assay, used with appropriate tissue processing techniques and controls, is a relatively fast, reproducible, quantitative method for detecting apoptosis in tissue. It can be used to confirm DNA damage and apoptosis as pathological mechanisms, to identify affected cell types, and to assess the efficacy of therapeutic treatments in vivo.

Detection and Analysis of DNA Damage in Mouse Skeletal Muscle In Situ Using the TUNEL Method

This video describes dissection, tissue processing, sectioning, and fluorescence-based TUNEL labeling of mouse skeletal muscle. It also describes a method for semi-automated analysis of TUNEL labeling.

Terminal deoxynucleotidyl transferase (TdT) deoxyuridine triphosphate (dUTP) nick end labeling (TUNEL) is the method of using the TdT enzyme to covalently ...

Measurement of Smooth Muscle Function in the Isolated Tissue Bath-applications to Pharmacology Research

Isolated tissue bath assays are a classical pharmacological tool for evaluating concentration-response relationships in a myriad of contractile tissues. While this technique has been implemented for over 100 years, the versatility, simplicity and reproducibility of this assay helps it to remain an indispensable tool for pharmacologists and physiologists alike. Tissue bath systems are available in a wide array of shapes and sizes, allowing a scientist to evaluate samples as small as murine mesenteric arteries and as large as porcine ileum &#8211; if not larger. Central to the isolated tissue bath assay is the ability to measure concentration-dependent changes to isometric contraction, and how the efficacy and potency of contractile agonists can be manipulated by increasing concentrations of antagonists or inhibitors. Even though the general principles remain relatively similar, recent technological advances allow even more versatility to the tissue bath assay by incorporating computer-based data recording and analysis software. This video will demonstrate the function of the isolated tissue bath to measure the isometric contraction of an isolated smooth muscle (in this case rat thoracic aorta rings), and share the types of knowledge that can be created with this technique. Included are detailed descriptions of aortic tissue dissection and preparation, placement of aortic rings in the tissue bath and proper tissue equilibration prior to experimentation, tests of tissue viability, experimental design and implementation, and data quantitation. Aorta will be connected to isometric force transducers, the data from which will be captured using a commercially available analog-to-digital converter and bridge amplifier specifically designed for use in these experiments. The accompanying software to this system will be used to visualize the experiment and analyze captured data.

This protocol describes the measurement of isometric contraction in an isolated smooth muscle preparation, using an isolated tissue bath system and computer-based data acquisition.

Isolated tissue bath assays are a classical pharmacological tool for evaluating concentration-response relationships in a myriad of contractile tissues.  ...

Murine Aortic Crush Injury: An Efficient In Vivo Model of Smooth Muscle Cell Proliferation and Endothelial Function

Arterial reconstruction, whether angioplasty or bypass surgery, involves iatrogenic trauma causing endothelial disruption and vascular smooth muscle cell (VSMC) proliferation. Common murine models study small vessels such as the carotid and femoral arteries. Herein we describe an in vivo system in which both VSMC proliferation and endothelial barrier function can be simultaneously assessed in a large vessel. We studied the infrarenal aortic response to injury in C57BL/6 mice. The aorta was injured from the left renal vein to the aortic bifurcation by 30 transmural crushes of 5-seconds duration with a cotton-tipped applicator. Morphological changes were assessed with conventional histology. Aorta wall thickness was measured from the luminal surface to the adventitia. EdU integration and counter staining with DAPI and alpha-actin was used to demonstrate VSMC proliferation. Activation of ERK1/2, a known moderator of intimal hyperplasia formation, was determined by Western Blot analysis. The effect of inflammation was determined by immunohistochemistry for B-cells, T-cells, and macrophages. En face sections of endothelium were visualized with scanning electron microscopy (SEM). Endothelial barrier function was determined with Evans Blue staining. Transmural injury resulted in aortic wall thickening. This injury induced VSMC proliferation, most prominently at 3 days after injury, and early activation of ERK1/2 and decreased p27kip1 expression. Injury did not result in increased B-cells, T-cells, or macrophages infiltration in the vessel wall. Injury caused partial endothelial cell denudation and loss of cell-cell contact. Injury resulted in a significant loss of endothelial barrier function, which returned to baseline after seven days. The murine transmural blunt aortic injury model provides an efficient system to simultaneously study both VSMC proliferation and endothelial barrier function in a large vessel.

Murine Aortic Crush Injury: An Efficient In Vivo Model of Smooth Muscle Cell Proliferation and Endothelial Function

Restenosis following cardiovascular procedures (bypass surgery, angioplasty, or stenting) is a significant problem reducing the durability of these procedures. An ideal therapy would inhibit smooth muscle cell (VSMC) proliferation while promoting regeneration of the endothelium. We describe a model for simultaneous assessment of VSMC proliferation and endothelial function in vivo.

Arterial reconstruction, whether angioplasty or bypass surgery, involves iatrogenic trauma causing endothelial disruption and vascular smooth muscle cell ...

A Rapid Automated Protocol for Muscle Fiber Population Analysis in Rat Muscle Cross Sections Using Myosin Heavy Chain Immunohistochemistry

Quantification of muscle fiber populations provides a deeper insight into the effects of disease, trauma, and various other influences on skeletal muscle composition. Various time-consuming methods have traditionally been used to study fiber populations in many fields of research. However, recently developed immunohistochemical methods based on myosin heavy chain protein expression provide a quick alternative to identify multiple fiber types in a single section. Here, we present a rapid, reliable and reproducible protocol for improved staining quality, allowing automatic acquisition of whole cross sections and automatic quantification of fiber populations with ImageJ. For this purpose, embedded skeletal muscles are cut in cross sections, stained using myosin heavy chains antibodies with secondary fluorescent antibodies and DAPI for cell nuclei staining. Whole cross sections are then scanned automatically using a slide scanner to obtain high-resolution composite pictures of the entire specimen. Fiber population analyses are subsequently performed to quantify slow, intermediate and fast fibers using an automated macro for ImageJ. We have previously shown that this method can identify fiber populations reliably to a degree of &#177;4%. In addition, this method reduces inter-user variability and time per analyses significantly using the open source platform ImageJ.

Here, we present a protocol for rapid muscle fiber analyses, which allows improved staining quality, and thereby automatic acquisition and quantification of fiber populations using the freely available software ImageJ.

Quantification of muscle fiber populations provides a deeper insight into the effects of disease, trauma, and various other influences on skeletal muscle ...

In Situ Immunofluorescent Staining of Autophagy in Muscle Stem Cells

Increasing evidence points to autophagy as a crucial regulatory process to preserve tissue homeostasis. It is known that autophagy is involved in skeletal muscle development and regeneration, and the autophagic process has been described in several muscular pathologies and age-related muscle disorders. A recently described block of the autophagic process that correlates with the functional exhaustion of satellite cells during muscle repair supports the notion that active autophagy is coupled with productive muscle regeneration. These data uncover the crucial role of autophagy in satellite cell activation during muscle regeneration in both normal and pathological conditions, such as muscular dystrophies. Here, we provide a protocol to monitor the autophagic process in the adult Muscle Stem Cell (MuSC) compartment during muscle regenerative conditions. This protocol describes the setup methodology to perform in situ immunofluorescence imaging of LC3, an autophagy marker, and MyoD, a myogenic lineage marker, in muscle tissue sections from control and injured mice. The methodology reported allows for monitoring the autophagic process in one specific cell compartment, the MuSC compartment, which plays a central role in orchestrating muscle regeneration.

In Situ Immunofluorescent Staining of Autophagy in Muscle Stem Cells

Active autophagy is associated with productive muscle regeneration, which is essential for Muscle Stem Cell (MuSC) activation. Here, we provide a protocol for the in situ detection of LC3, an autophagy marker in MyoD-positive MuSCs of muscle tissue sections from control and injured mice.

Increasing evidence points to autophagy as a crucial regulatory process to preserve tissue homeostasis. It is known that autophagy is involved in skeletal ...