Name: design and application of a fault detection method based on adaptive filters and rotational speed estimation for an electro-hydrostatic actuator
Uploaded: 2022-10-28T13:00:00
Description: Watch this Scientific Journal Video about Design and Application of a Fault Detection Method Based on Adaptive Filters and Rotational Speed Estimation for an Electro-Hydrostatic Actuator at JoVE.com

This work was supported by the Chinese Civil Aircraft Project (No. MJ-2017-S49) and the China
Postdoctoral Science Foundation (No. 2021M700331).

1. Establishment of the EHA simulation model
<ol>
	<li>Open the simulation software on a PC.</li>
	<li>Build the simulation model for the EHA (Figure 2), according to the mathematical equations of the EHA model15, and conduct a three-loop PI as the controller. Encapsulate the hydraulic module (Figure 2C), electrical module (Figure 2B), and controller (Figure 2B...

<ol>
	<li>Fu, Y., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Review+on+design+method+of+electro-hydrostatic+actuator.">Review on design method of electro-hydrostatic actuator.</a> Journal of Beijing University of Aeronautics and Astronautics. 43 (10), 1939-1952 (2017).</li><li>Qi, H., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Modelling+and+simulation+of+a+novel+dual-redundancy+electro-hydrostatic+actuator.">Modelling and simulation of a novel dual-redundancy electro-hydrostatic actuator.</a> 2015 International Conference on Fluid Power and Mechatronics (FPM) IEEE. , 270-275 (2015).</li><li>Chao, Q., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Integrated+slipper+retainer+mechanism+to+eliminate+slipper+wear+in+high-speed+axial+piston+pumps.">Integrated slipper retainer mechanism to eliminate slipper wear in high-speed axial piston pumps.</a> Frontiers of Mechanical Engineering. 17, (2022).</li><li>Yoo, M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+resilience+measure+formulation+that+considers+sensor+faults.">A resilience measure formulation that considers sensor faults.</a> Reliability Engineering&amp; System Safety. 199, 106393 (2019).</li><li>Fang, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Online+inverter+fault+diagnosis+of+buck-converter+BLDC+motor+combinations.">Online inverter fault diagnosis of buck-converter BLDC motor combinations.</a> IEEE Transactions on Power Electronics. 30 (5), 2674-2688 (2015).</li><li>Lisnianski, A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Power+system+structure+optimization+subject+to+reliability+constraints.">Power system structure optimization subject to reliability constraints.</a> Electric Power Systems Research. 39 (2), 145-152 (1996).</li><li>Fu, T., Wang, L., Qi, H., Liu, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Fault+diagnosis+and+management+of+electric+hydrostatic+actuator.">Fault diagnosis and management of electric hydrostatic actuator.</a> Machine Tool &amp; Hydraulics. 38 (9), 120-124 (2010).</li><li>Maddahi, A., Kinsner, W., Sepehri, N. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Internal+leakage+detection+in+electrohydrostatic+actuators+using+multiscale+analysis+of+experimental+data.">Internal leakage detection in electrohydrostatic actuators using multiscale analysis of experimental data.</a> IEEE Transactions on Instrumentation and Measurement. 65 (12), 2734-2747 (2016).</li><li>Guo, S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Hydraulic+piston+pump+in+civil+aircraft:+Current+status,+future+directions+and+critical+technologies.">Hydraulic piston pump in civil aircraft: Current status, future directions and critical technologies.</a> Chinese Journal of Aeronautics. 33 (01), 16-30 (2020).</li><li>Jackson, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Real-time+model-based+fault+detection+and+diagnosis+for+automated+systems.">Real-time model-based fault detection and diagnosis for automated systems.</a> IEEE Industry Applications Society Dynamic Modeling Control Applications for Industry Workshop. , 26-28 (1997).</li><li>Alcorta, G. E., Zolghadri, A., Goupil, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+novel+non-linear+observer-based+approach+to+oscillatory+failure+detection.">A novel non-linear observer-based approach to oscillatory failure detection.</a> 2009 European Control Conference (ECC). , 1901-1906 (2009).</li><li>Castaldi, P., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Design+of+residual+generators+and+adaptive+filters+for+the+FDI+of+aircraft+model+sensors.">Design of residual generators and adaptive filters for the FDI of aircraft model sensors.</a> Control Engineering Practice. 18 (5), 449-459 (2010).</li><li>Zhu, P., Dong, W., Mao, Y., Shi, H., Ma, X. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Kernel+adaptive+filtering+multiple-model+actuator+fault+diagnostic+for+multi-effectors+aircraft.">Kernel adaptive filtering multiple-model actuator fault diagnostic for multi-effectors aircraft.</a> 2019 12th Asian Control Conference (ASCC). , 1489-1494 (2019).</li><li>Hidayat, R., Ramady, G. D., Lestari, N. S., Mahardika, A. G., Fadriani, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Optimization+of+normalized+least+mean+square+algorithm+of+smart+antenna+beamforming+for+interference+mitigation.">Optimization of normalized least mean square algorithm of smart antenna beamforming for interference mitigation.</a> Journal of Physics: Conference Series. 1783, 012085 (2021).</li><li>Fu, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Modelling+and+simulation+of+flight+control+electromechanical+actuators+with+special+focus+on+model+architecting,+multidisciplinary+effects+and+power+flows.">Modelling and simulation of flight control electromechanical actuators with special focus on model architecting, multidisciplinary effects and power flows.</a> Chinese Journal of Aeronautics. 30 (1), 47-65 (2017).</li><li>Li, Z., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=New+normalized+LMS+adaptive+filter+with+a+variable+regularization+factor.">New normalized LMS adaptive filter with a variable regularization factor.</a> Journal of Systems Engineering and Electronics. 30 (2), 259-269 (2019).</li></ol>

When conducting these experimental steps, it was important to ensure the real-time capability of the algorithm in order to obtain accurate calculation results. The white noise in the signal acquisition process was adopted to simulate the characteristics of the actual sensor in order to make the simulation closer to reality. In the simulations and experiments, moving average filters were applied to reduce the fluctuation in the identified resistance and estimated rotational speed, which made the fault characteristics more...

The electro-hydrostatic actuator (EHA) is a key component for flight control in more electric aircraft (MEA). The typical structure of an EHA is shown in Figure 1. Its compact structure guarantees high power density, low maintenance, and higher fault tolerance and safety compared with the traditional hydraulic servo actuator (HSA)1. However, the current reliability of the EHA cannot meet the practical requirements of more electric aircraft2. As a result, redundancy technology has been introduced into the design of the EHA. To maximize the effectiveness of the redundancy technology, the operating status of the system should be monitored by a fault detection method3. According to the location where the fault occurs, the fault modes of the EHA can be divided into servo controller faults and power control unit (PCU) faults. PCU faults can be further divided into sensor faults, electromechanical unit faults, and hydraulic unit faults. The fault mechanism of the servo controller has little relationship with the EHA body, and the fault probability of the sensor is much lower than that of the equipment component4. Therefore, we focus on the faults of the electromechanical unit and hydraulic unit in this paper.
Electromechanical unit faults include motor drive module faults and brushless DC motor (BLDCM) faults. Generally, the probability of a power drive electronics (PDE) fault (e.g., a short-circuit fault, an open-circuit fault) is relatively high. When a short-circuit fault occurs, the PDE current rises sharply in a short amount of time, causing severe consequences such as a motor shutdown or damage to the electrical components. Although the motor can maintain its working status after an open-circuit fault occurs, overcurrent and overvoltage for the other electrical components are still inevitable, and secondary faults may consequently happen5. As for the BLDCMs, the motor windings are most prone to faults from a short circuit or an open circuit6. The PDE in the electromechanical unit is connected in series with the corresponding motor windings. The fault detection method designed for the motor windings is also effective when dealing with faults in the PDE. Therefore, electromechanical unit faults, including both in the motor and the PDE, should be detected online.
Hydraulic unit faults include fault occurrences in the fixed-displacement piston pump, integrated valve block, and actuating cylinder7. The EHA&#39;s piston pump is composed of pistons, swash plates, and valve plates; damage to the seal and wear of the valve plate are the main forms of fault8. These two fault modes increase the leakage of the pump. Abnormal changes in the output flow and pressure follow and, eventually, lead to a decrease in the speed of the actuating cylinder and a reduction in the servo performance of the system. The fault modes of the integrated valve block include a pressurized reservoir fault, a check valve fault, a relief valve fault, and a mode selection valve fault. The pressurized reservoir usually adopts a self-boosting design with high reliability. When a fault occurs, however, insufficient charge pressure causes cavitation of the pump, resulting in abnormal output flow. Spring fatigue, component wear, and deformation are common fault modes in the check valves and relief valves. A check valve fault presents as a reverse leakage, which directly leads to abnormal flow. A relief valve fault leads to an invalid protection function, resulting in abnormal pressure. The common faults of the mode selection valve are failure of the return spring and broken wire coils. The former causes in-current switching of the working status, leading to abnormal movement of the actuating cylinder. An actuating cylinder fault results in a decrease in position control precision and dynamic performance. In summary, faults of the hydraulic units cause abnormal flow and pressure9. Since the flow and motor rotational speed are approximately proportional in an EHA system, the rotational speed can be monitored online to detect abnormal flow and pressure due to sudden faults.
Corresponding fault detection methods aimed at the previously mentioned electromechanical unit faults and hydraulic unit faults need to be designed. The methods for fault detection in an electromechanical system mainly include state estimation and parameter identification10. A state observer is built on the basis of a mathematical model of the system that makes a state estimation and determines faults by analyzing the residual sequence generated by the observer. Alcorta et al. proposed a simple and novel nonlinear observer with two correction terms for vibration fault detection in commercial aircraft, which is highly effective11. However, this type of method must solve the robustness problem of the observer. In other words, it must suppress the changes in the residual sequence caused by non-fault information such as model error or external disturbances. Moreover, this method often requires very accurate model information, which is usually difficult to collect in practical engineering applications.
The parameter identification method employs certain algorithms for identifying the important parameters in the system. When a fault occurs, the corresponding parameter value also changes. Therefore, faults can be detected by detecting a change in the parameters. The parameter identification method does not require the calculation of the residual sequence, so it can avoid the effect of disturbances on the detection accuracy. The adaptive filter has been widely used in parameter identification due to its easy implementation and stable performance, meaning it is a favorable and feasible method for electromechanical fault detection12. Zhu et al. proposed a new multi-model adaptive estimation fault detection method based on kernel adaptive filters, which realizes the estimation of the real flight state value and the actuator fault detection online with good performance13.
Referring to the previous research, corresponding fault detection methods have been designed. The resistance of the windings abruptly changes when electrical faults occur, such as open-circuit faults or short-circuit faults. Therefore, an adaptive filter was designed based on an NLMS algorithm to identify the resistance of the windings, which can determine whether an electrical fault has occurred. Combining an adaptive filter with an NLMS algorithm to minimize the change of the parameter vector leads to a better and faster convergence effect14. For hydraulic unit faults, a rotational speed estimation algorithm was proposed based on the clear analytical relationship between the rotational speed of the pump and the position of the actuating cylinder. EHA hydraulic faults were detected online by comparing the estimated rotational speed with the actual speed in real time.
In this paper, a test method combining simulations and experiments was adopted. First, a mathematical model of the EHA was built, and a simulation for the proposed fault detection method was performed. The simulation included the verification of the detection methods in non-fault and fault injection conditions. Then, the fault detection method was realized in the real servo controller. Finally, the results of the simulations and experiments were analyzed and compared to evaluate the efficacy of the fault detection method.

<table border="1" fo:keep-together.within-page="1" fo:keep-with-next.within-page="always">
	<tbody>
		<tr>
			<td>LabVIEW</td>
			<td>NI</td>
			<td>NI LabVIEW 2018</td>
			<td></td>
		</tr>
		<tr>
			<td>Matlab/SIMULINK</td>
			<td>MathWorks.Inc</td>
			<td>R2020a</td>
			<td></td>
		</tr>
		<tr>
			<td>Personal Computer</td>
			<td>Lenovo</td>
			<td>Y7000 2020H</td>
			<td></td>
		</tr>
		<tr>
			<td>24V Switching Power Supply</td>
			<td>ECNKO</td>
			<td>S-250-24</td>
			<td></td>
		</tr>
		<tr>
			<td>Programmable Current Source</td>
			<td>Greens Pai</td>
			<td>GDP-50-30</td>
			<td></td>
		</tr>
	</tbody>
</table>

design and application of a fault detection method based on adaptive filters and rotational speed estimation for an electro-hydrostatic actuator

The electro-hydrostatic actuator (EHA) is a promising actuating apparatus used in flight control systems for more electric aircraft (MEA) due to its high power density and low maintenance. Since the reliability of the system decreases with increasing complexity, fault detection is becoming increasingly important. In this paper, an adaptive filter was designed based on a normalized least mean square (NLMS) algorithm, which could identify the resistance of the motor windings online to detect electrical faults in the EHA. Additionally, based on the analytical relationship between rotational speed and displacement, a rotational speed estimation method was designed. By comparing the actual rotational speed with the estimated one, hydraulic faults could be detected. To verify the efficacy of the aforementioned method, software was applied for the modeling and simulations, which included fault injection and detection. On this basis, an experimental platform was built and then subjected to a series of validation experiments. The results indicate that the fault detection method has the potential to detect electrical and hydraulic faults in an EHA.

In the simulation, the actual position and target position curve of the EHA piston rod in the non-fault condition is shown in Figure 7. According to the curve, the system was operating normally, with good dynamic characteristics. The actual position and target position curve of the EHA piston rod in the electromechanical fault injection condition is shown in Figure 8. According to the curve, the system could not track the target accurately. The results of the re...

Watch this Scientific Journal Video about Design and Application of a Fault Detection Method Based on Adaptive Filters and Rotational Speed Estimation for an Electro-Hydrostatic Actuator at JoVE.com

Design and Application of a Fault Detection Method Based on Adaptive Filters and Rotational Speed Estimation for an Electro-Hydrostatic Actuator

In this paper, an adaptive filter based on a normalized least mean square (NLMS) algorithm and a rotational speed estimation method are introduced to detect the electrical and hydraulic faults of the electro-hydrostatic actuator (EHA). The efficacy and feasibility of the aforementioned methods are verified through simulations and experiments.

The electro-hydrostatic actuator (EHA) is a promising actuating apparatus used in flight control systems for more electric aircraft (MEA) due to its high ...

Fault detection is a key technology to test the practicality of electro-hydrostatic actuator, also known as EHA. This protocol possess an effective design experiment method for EHA fault detection. This protocol combines simulation and experiment fault detection algorithms that can detect the errors of EHA effectively and quickly.To establish the EHA simulation model open the simulation software on a PC and set the parameters of the model as described in the text manuscript. Then give a position command, a sinusoid with an amplitude of 0.01 meter, and a frequency of two pi radius per second. Enter the modeling menu and click the model settings"button.Set the simulation operation parameters starting with a start time of zero seconds, a stop time of six seconds, the type as variable step, and the solver as auto. Double click the fault injection switches to set the model to work in a non-fault condition. Click the run button to run the simulation and receive the non-fault condition results.Run the drawing software to draw the curve of the piston rod misplacement. Double click the insert electromechanical fault switch to inject an electromechanical fault at three seconds, which sets the resistance to 1000 ums to simulate an open circuit fault of the motor windings. Repeat the simulation run as demonstrated earlier to attain the results for the electromechanical fault condition.Run the drawing software to draw the curves of the piston rod displacement and the identified resistance. Turn the insert hydraulic fault switch to inject a hydraulic fault at three seconds which increases the leakage value to 2.5 times 10^9 cubic meters per second per pascal, to simulate a hydraulic unit fault. Then run the simulation model as demonstrated earlier to attain the results for the hydraulic fault condition.Run the drawing software to draw the curves of the piston rod displacement and rotational speed estimation results. Position the PC, EHA, and Servo controller. Open the host software interface on the PC and establish communication between the Servo controller and the PC.Select the appropriate serial port from the software's visa resource name dropdown window.Click the run button to start the software. Observe the receiving area and the corresponding curves of the software to determine whether the data receiving function is normal. Click the solenoid valve two button to observe whether the solenoid valve red light is lightened and determine whether the data transmission function is normal.Provide drive power to the Servo controller and set the voltage to 50 volts dc. Click the EHA switch button on the software to set the EHA to a running state. Click the data log button to start data logging.The recorded data will include various parameters, such as the actual position, the target position, the actual speed, the target speed, the bus current, and the voltage. Conduct a pre-run for the EHA and give position commands on the software. Which include a step of plus five and minus five millimeters.Observe whether the EHA is actuating normally. Give a position command on the software a sinusoid with an amplitude 10 millimeters and a frequency of one hertz. Observe whether the identified resistance and the estimated rotational speed are consistent with the values under non-fault operating conditions.Put the position command back to the original state, if the result is correct. Click the EHA switch button to stop the EHA and cut off the drive power. Then stop the host computer software and interrupt the communication between the Servo controller and the PC.Export the experimental data, analyze the data, and draw curves of the experimental results using drawing software.Then proceed with result analysis as described in the text manuscript. In the simulation run, the actual and target position curve of the EHA piston rod in the non-fault condition operated normally with good dynamic characteristics. However, the position curve in the electromechanical fault injection could not track the target accurately.The resistance identification algorithm demonstrated that before and after injection the identified value converged to the true value, indicating that the method achieved the desired effect. The actual and target position curves in the hydraulic fault injection condition could not track the target accurately. Before injection, the estimated rotational speed was very close to the actual rotational speed.While after injection, a hydraulic fault could be determined according to the excessive error in the rotational speed. The experimental results were in accordance with the simulation results. The resistance identification algorithm showed that the identified value converged to the true value of 0.3 oms consistent with the simulation, indicating that the method achieved the desired effect.The corresponding rotational speed estimate was close to the actual rotational speed, and rotational speed error essentially fluctuated in the acceptable range of zero to 2.5 RPS. Fault detection technology is a key to EHA redundancy and the health management. Which can pave the way for further practicality of EHA.

Research

Education

JoVE Core

JoVE Journal

Mechanical Engineering

Engineering

Unit 1

Energy Methods

SCIENTISTS IN ACTION

Visualization of High Speed Liquid Jet Impaction on a Moving Surface

Two apparatuses for examining liquid jet impingement on a high-speed moving surface are described: an air cannon device (for examining surface speeds ...

A High Performance Impedance-based Platform for Evaporation Rate Detection

This paper describes the method of a novel impedance-based platform for the detection of the evaporation rate. The model compound hyaluronic acid was ...

Design and Characterization Methodology for Efficient Wide Range Tunable MEMS Filters

Here, we demonstrate the advantages of the laser Doppler vibrometer (LDV) over conventional techniques (the network analyzer), as well as the techniques ...

The Modular Design and Production of an Intelligent Robot Based on a Closed-Loop Control Strategy

Intelligent robots are part of a new generation of robots that are able to sense the surrounding environment, plan their own actions and eventually reach ...

A Fabrication and Measurement Method for a Flexible Ferroelectric Element Based on Van Der Waals Heteroepitaxy

Flexible non-volatile memories have received much attention as they are applicable for portable smart electronic device in the future, relying on ...

A Pipette-Tip Based Method for Seeding Cells to Droplet Microfluidic Platforms

Amongst various microfluidic platform designs frequently used for cellular analysis, droplet-microfluidics provides a robust tool for isolating and ...

Application of Design Aspects in Uniaxial Loading Machine Development

In terms of accurate and precise mechanical testing, machines run the continuum. Whereas commercial platforms offer excellent accuracy, they can be ...

Design and Fabrication of an Optical Fiber Made of Water

In this report, an optical fiber of which the core is made solely of water, while the cladding is air, is designed and manufactured. In contrast with ...

Design and Implementation of a Bespoke Robotic Manipulator for Extra-corporeal Ultrasound

With the potential for high precision, dexterity, and repeatability, a self-tracked robotic system can be employed to assist the acquisition of real-time ...

Implementation of a Nonlinear Microscope Based on Stimulated Raman Scattering

Stimulated Raman scattering (SRS) microscopy uses near-infrared excitation light; therefore, it shares many multi-photon microscopic imaging properties. ...