The authors thank the staff of the WVU Center for Alternative Fuels, Engines, and Emissions, including Mr. Zachary Luzader and Mr. Christopher Rowe. The author's thank the Environmental Defense Fund, the WVU Research Corporation, and the George Berry Foundation for funding the research programs that provided field data and a variety of test conditions under which to use the developed FFS.

Note: The FFS has been engineered with safety in mind to eliminate or reduce the possibility of ignition of a methane or natural gas source. Natural gas is flammable in ambient conditions for volume concentrations from 5% to 15%. The system will be tested and demonstrated to meet safety requirements. Modification or tampering with the system could cause serious injury.
1. Calibration of the MAF
Note: The MAF requires periodic calibration against a National Institute of Standards and Technology (NIST) traceable laminar flow element (LFE). Use the calibrations tools within the program to complete a MAF calibration against a known LFE. The program will collect all data necessary from the pressure transducers, humidity sensor, and MAF to create a new calibration. It is recommended that an 11-point calibration be completed. If a calibration is older than one month, a new calibration should be completed. Old calibrations can be viewed and used.
<ol>
	<li>Choose a properly sized LFE to ensure that the flow range is larger than 25% of the lower flow range of the LFE.</li>
	<li>Connect the MAF to a flow bench ensuring the inlet to the MAF is at least 10 diameters downstream of any restriction or expansion.</li>
	<li>Connect a combined absolute/differential pressure meter to the differential pressure ports of the flow bench LFE.
	<ol>
		<li>Ensure the differential pressure transducer is within calibration. Connect the high side port of the sensor to the upstream LFE port. Connect the low side port of the sensor to the downstream port of the LFE.</li>
		<li>Ensure that the absolute pressure transducer of the combined differential/absolute pressure meter is within calibration and connect via a &#39;tee&#39; fitting to high side port of the differential pressure sensor.</li>
	</ol>
	</li>
	<li>Connect a K-type thermocouple to the data acquisition unit (DAQ).</li>
	<li>Ensure that the dew point measurement device is within calibration and connected to the DAQ and the air stream.</li>
	<li>Ensure that MAF and flow bench signals are acceptable (0-5 volts) and use the software calibrations screen to begin a MAF calibration.</li>
	<li>Set the flow at 11 different flow rates across the expected range of the MAF and within the acceptable range of the LFE. Collect a minimum of 30 sec of data at each flow condition at a minimum rate of 1 Hz by clicking the collect calibration data button. 
	Note: Ensure that the MAF calibration spans at least 25% of the minimum flow rate of the LFE used for calibration. Do not exceed the maximum flow rate of the LFE, if larger flow rates are to be calibrated, use a larger LFE.</li>
	<li>Run the calibration software by clicking Process Calibration Data button and select the curve fit that yields minimal total error without a single point error beyond &#177; 2%.</li>
</ol>
2. Calibration of the Greenhouse Gas Analyzer
Note: The greenhouse gas analyzer should be calibrated internally on an annual basis by a third party. Users can use the calibrations tools within the software to complete an external calibration or verification. The calibration uses bottled gases of known concentration. The gas is mixed with nitrogen through a gas divider and exits to a flooded probe. The analyzer intakes the sample at the known flow rate and records the value. It is recommended that an 11-point calibration be completed over the range of interest. The program automatically adjusts for gas concentration and viscosity within the gas divider.
<ol>
	<li>Prior to field-testing, perform an external verification or calibration if necessary (previous calibrations older than one month).</li>
	<li>Power the GHG sensor on for 15 min prior to verification/calibration and connect the verification &#39;tee&#39; fitting to the inlet port of the sensor.</li>
	<li>Select an EPA Protocol or NIST traceable gas to verify and use ultra-high purity nitrogen (UHPN) as the balance gas.</li>
	<li>Connect the verification gas (methane) to the component port of a calibrated gas divider using approved regulators (CGA 580 for UPHN, CGA 350 for methane). Connect the outlet of the gas divider to the &#39;tee&#39; of step 2.2.</li>
	<li>Set the component gas, outlet pressure to approximately 23 pounds per square inch - gauge (PSIG) by adjusting the regulator knob. Set the balance gas, outlet pressure to approximately 19 PSIG. Set the flow rate of the gas divider to at least two times the internal flow rate of the sample pump with the gas divider, flow control knob (Current sample pump operates at two standard liters per minute (SLPM) so the outlet of the gas divider should be set at 4 SLPM). 
	Note: Adequately flood the sample probe with the gas mixture to ensure a proper verification. Use secondary rotameter if available to ensure a net positive flow out of the flood probe &#39;tee&#39; of step 2.3.</li>
	<li>Click start calibration and enter the bottle concentration of the component gas (in ppm). Use the gas divider to select component gas ranges from zero to 100% (11 total points). Collect data for a minimum of 30 sec at each setting of the gas divider to complete the linearization.</li>
	<li>Select whether a new external calibration is applied. 
	Note: If the verification passes within the uncertainty of the gas bottle concentration (typically 1-2%) then a new external calibration does not need to be created.</li>
	<li>Repeat the prior steps for single or multiple point verifications/calibrations of methane, carbon dioxide, or water vapor.</li>
</ol>
3. Full System Recovery Test
Note: A full system recovery test is completed to ensure that the FFS recovers and accurately reports a known volume of calibration gas.
<ol>
	<li>Power on the FFS and ensure the GHG sensor has been on for at least 15 min. Select a recovery gas to test - methane.</li>
	<li>Connect the gas bottle to an appropriate regulator and set the outlet pressure to approximately 20 PSIG.</li>
	<li>Connect a supply line to the gas bottle regulator and the inlet to a calibrated mass flow controller (MFC). Connect the outlet of the MFC to the inlet of the sampling hose. Select the gas recovery verification tab in the DAQ software and connect the serial connection of the MFC to the DAQ.</li>
	<li>Click start the gas recovery test and record the background data for at least 30 sec, the known flow rate of gas can be entered at this time.</li>
	<li>Set the flow rate of recovery gas to an average leak size based on expected or previous values (20 SLPM or 30 SLPM). Begin flowing the recovery gas and let the system stabilize for 30 sec.</li>
	<li>After stabilization, click record, and allow the program to record the leak verification data for 30 sec. 
	Note: Upon completion of sampling the software will create a report showing the error of the between the known gas flow rate and the recovered gas flow rate. An error of &#177;4.4% is acceptable (relative measurement uncertainty of the system), but the targeted recovery error is &#177;2%.</li>
	<li>Repeat the gas recovery test at least three times and ensure that all errors are within the acceptable range.</li>
	<li>Examine the system for any faults if the error is beyond &#177;4.4%. Double-check all connections, flow rates, remedy errors, and repeat steps 3.2 to 3.6. 
	Note: Faults may include that the supply line may not have been inserted into the FFS sampling hose or connections were loose on sample fittings. A new MAF calibration or sensor verification may be necessary if not previously completed (within a month).</li>
</ol>
4. Leak Detection Audit
Note: Perform a site inventory to identify each potential source of fugitive emissions. The inventory will include the number of sources (valves, flanges, pumps/compressors, vents, etc.) broken down by source group (compressor building, storage farm, vehicle fueling rack, etc.) The leak detection audit can occur in parallel or series with the leak quantification. A handheld methane detector or optical gas-imaging camera can be used to examine components for leaks. When leaks are identified record a description, concentration, and take an image. Mark the leak for later quantification or quantify the leak at this time.&#160;
<ol>
	<li>Create a new inventory file in the program. Enter details on the site for inventory and reporting purposes (name, type of site, etc.). Date, time stamp, and GPS location are automatically populated.</li>
	<li>Zero the handheld methane detector on ambient air prior to use. Utilize a handheld methane detector with sampling probe to check all potential interfaces that are accessible for the presence of fugitive emissions. Position the probe sample inlet orthogonal to the surface to minimize dilution. 
	Note: The sensitivity of the handheld unit is 5 ppm above background when zeroed on ambient air.
	<ol>
		<li>Document any inaccessible sources or aggregated sources. 
		Note: Inaccessible sources could include vent pipes that are beyond a safely accessible height as determined by the site operator. Aggregated sources may include multiple pneumatic valves attached to a manifold or enclosed by a service box. If the source or multiple sources can be examined as a whole using an enclosure, aggregate the sources.</li>
		<li>Aggregate multiple sources using an enclosure with at least one entrance and one exit. Document all sources within the perimeter of the enclosure. Label the source as an aggregate sample and proceed using quantification of section 5. 
		Note: Use of a leak detector solution is allowed to classify sources a &#34;non-leaking&#34;. Holding the bottle upright, apply enough leak detector solution to cover the interface. Allow 5-10 sec for bubbles to form.</li>
	</ol>
	</li>
	<li>Place the probe inlet of the detection instrument at the surface of the component interface. Move the probe along the interface periphery while observing the instrument readout, taking care to consider the delayed response time of the instrument.</li>
	<li>Slowly sample the interface where leakage is indicated until the maximum meter reading is obtained.</li>
	<li>Leave the probe inlet at this maximum reading location for approximately two times the instrument response time (20 sec). If the maximum observed meter reading is greater than 500 parts per million (ppm), record, and report the result. Click take leak image for reporting purposes.</li>
	<li>Alternatively, use an infrared imaging device to scan slowly the components to examine for leaks. This method is approved as an alternative work practice to detect leaks from equipment under EPA Method 21 - optical gas imaging.
	<ol>
		<li>Turn on the camera and allow for stabilization.</li>
		<li>Remove the lens cover and use the camera screen to scan slowly the components for leaks. 
		Note: Optical gas imagining cameras are typically expensive but do reduce the time required to scan components for leaks. Use of high sensitivity modes may be required for small leaks.</li>
		<li>If a leak is detected with the camera, either record video or an image for reporting purposes. Mark the leak locations for subsequent quantification with the FFS.</li>
	</ol>
	</li>
</ol>
5. Leak Rate Quantification
Note: Leak rate quantification may be complete at the same time as leak detection or after an inventory of leaks has been completed. Quantification occurs under the new leak button after entering site and leak data. The user must select whether to use a local or global background. In either case, the system will control the proper solenoid valves and record a timed sample. Once a background has been taken, the leak should be quantified three times or from three directions to ensure proper leak capture. The system will analyze the three measurements and report the variance. Users may save the leak data (separate and average), repeat the capture, or classify the source as variable.
<ol>
	<li>Measure and record methane background concentrations periodically throughout the site visit and with every leak quantification. 
	Note: It is of high importance to take separate backgrounds for leaks that are within a similar region and under conditions when the dilatation air may contain a slipstream of nearby leaks. Combined leak analysis of systems is discussed below &#8212; 5.15.</li>
	<li>Quantify any identified leaks. Prior to approaching the leak with the sample hose ensure that the grounding strap is in contact with the ground and clip the clip the sampler ground clamp to the item in question. Using the FFS, position the sampling hose at multiple points around the area of the leak source to obtain three consecutive leak rate quantifications for that source that included the continuously recorded sample flow and sample concentration.</li>
	<li>Adjust the full flow rate to increase volumetric flow by opening or closing the iris duct on the intake of the blower. Adjust the duct valve to ensure that the maximum methane concentration is within 10% of the highest calibrated value or that minimum methane concentration is at least 2 ppm higher than the background concentration.</li>
	<li>In the program, press the quantify leak button. An option to use a global or local background will prompt the user.</li>
	<li>When in doubt of contamination from other leaks, always take a local background. With the hose in the leak quantification position, click take local background. Once completed the program will prompt the user to quantify the leak. 
	Note: The program automatically switch the sampling location of the outlet of the FFS to a port just behind the inlet to the sampling hose for a local background. The sampling hose must be in the same measurement position as is used for the sample quantification.</li>
	<li>Repeat the record leak prompt three times, especially in the cases of high ambient wind conditions or in complex geometries.
	<ol>
		<li>If the variance of the additional quantifications is above 10%, investigate to determine if the variance is the result of instrument malfunction or variability in leak rate.</li>
		<li>If the source of variability in leak rate is due to instrument malfunction, remedy the source of malfunction and re-quantified. Otherwise, classify the leak as &#34;variable&#34; and record the suspected cause.</li>
	</ol>
	</li>
	<li>In the case of multiple sources in close proximity or a single source enclosed by a covering, treat the source(s) in question as a single source for leak quantification using an enclosure. Use the Enclosure tab to perform this type of quantification.
	<ol>
		<li>Fabricate an enclosure entirely of plastic sheeting or incorporated either flexible, non-permeable material, or rely on a permanent enclosure such as a compressor housing. 
		Note: The enclosure allows the quantification device to capture any natural gas that is leaking from components within its boundaries and allows for dilution of the captured natural gas via purposely-placed holes in the enclosure or from existing vent locations on permanent enclosures.</li>
		<li>Allow any natural gas being diluted to be drawn from the enclosure and to achieve a steady reading from the GHG sensor. The duration of quantification sampling performed using an enclosure is dependent upon the size of the enclosure.</li>
		<li>Situate the points at which the quantification sample drawn from the enclosure such that the dilution air flows across the potential leak source(s) to reduce the duration of sampling allowing for steady concentration readings</li>
	</ol>
	</li>
	<li>If a bag sample is required, place an evacuated sample bag of the bagging box to the outlet of the GHG sensor. Use the software to record bag sample, identification number and on-screen timer to ensure a full bag sample for off-site analysis has been taken.</li>
</ol>

The authors, along with Mr. Christopher Rowe and Mr. Zachary Luzader have filed invention disclosures and provisional patents with West Virginia University's Research Corporation and Office of Technology Transfer to protect the intellectual property associated with this system.

In order to improve accuracy and overcome current industry limitations, we created the Full Flow Sampling System (FFS) for methane quantification. Researchers used the system in a variety of forms in numerous locations across North America. Use of spectroscopy eliminates significant interference from C2+ compounds and the non-destructive sampling nature allows for bag sampling of the leak for alternative analysis offsite. When combined with alternative wind blocks the system has successfully and accurately quantified methane emissions from the following items: CNG fuel systems, LNG fuel systems, internal combustion engine crankcases, piping, tubing, connectors, flanges, compressor vents, well head components, water/oil separator tanks, valve, pneumatic actuators driven by natural gas, well casings, and numerous other natural gas related components. System platforms included portable carts, on-road, and off-road vehicles. Power consumption does require the use of a generator or house power through standard 120 VAC connections. However, through this use of &#39;grid&#39; power the system can sample at higher flow rates yet still be used in conjunction with extension cords and long sampling houses for portability around a given site of interest. Current battery powered systems have decreased performance as a function of battery state of charge which is eliminated using grid power.
Periodic calibrations protocols have been developed and integrated into the user-interface. Protocols 1-3 should be completed prior to any new site audit or at a minimum on a monthly basis. If users do not diligently follow the protocols, the system may under or over-report emissions rates, which could negatively affect GHG reporting. The primary goal of the protocols is to ensure an accurate system to estimate total site emissions with component granularity. If statistical analysis are used to create new emissions factors, then each non-leaking component must also be recorded.
The leak detection process can be time consuming with the use of handheld units. The use of an optical gas-imaging camera can significantly reduce the time required for leak detect. The camera must be capable of measuring volatile organic compounds including methane. Currently available commercial units have sensitivities on detectable leak rates of approximately 0.8 grams per hour (g/hr) and are dependent upon wind conditions. Imaging devices are also sensitive to temperature. Be sure to adjust temperature scales as necessary. Extremely cold vapors (cryogenic natural gas) or superheated vapors (steam in exhausts and others) can appear as excessive leaks. Subsequent quantification must follow to determine accurately the actual leak rate of any imaged leak. Use of infrared cameras can significantly reduce leak detection inventories, but are sensitive to wind conditions. Smaller leaks under high wind conditions could diffuse more rapidly and not be spotted. When in doubt, always double check with a hand held methane detector.
A user-friendly interface ensures easy and proper use of the FFS. Integrated user prompts assist the user along the Protocol and reduce post-processing efforts. For example, once a leak quantification is completed (Section 5), the average leak rate based on calculations using at least 30 sec&#160;of continuous concentration and flow rate recordings will be reported. User prompts will automatically use global or local background concentrations. Simple on-screen selection will cause solenoids to operate and sample for the correct locations. Users should follow all on-screen prompts to ensure accurate quantification of the leak. The program will automatically correct for the following: global or local background; temperature; mass flow rate (assumed air with carbon dioxide and methane corrections); humidity (measured from the GHG sensor); temperature (thermocouple - redundant check for ambient conditions)
The relative uncertainty of measured methane emissions rates is &#177;4.4% except in circumstances where the leak is inconsequential as the concentration measured approached background concentration. An example of component uncertainties is provided in Table 2.
<table fo:keep-together.within-page="1">
	<tbody>
		<tr>
			<td>Source</td>
			<td>Uncertainty (%)</td>
		</tr>
		<tr>
			<td>Methane Sensor</td>
			<td>1</td>
		</tr>
		<tr>
			<td>Methane sensor calibration correlation</td>
			<td>0.73</td>
		</tr>
		<tr>
			<td>Methane gas bottle</td>
			<td>1</td>
		</tr>
		<tr>
			<td>Zero air gas bottle</td>
			<td>0.1</td>
		</tr>
		<tr>
			<td>LFE</td>
			<td>0.7</td>
		</tr>
		<tr>
			<td>MAF</td>
			<td>4</td>
		</tr>
		<tr>
			<td>Differential pressure module</td>
			<td>0.025</td>
		</tr>
		<tr>
			<td>Absolute pressure module</td>
			<td>0.06</td>
		</tr>
		<tr>
			<td>Thermocouple</td>
			<td>0.4</td>
		</tr>
		<tr>
			<td>MAF calibration correlation</td>
			<td>0.09</td>
		</tr>
		<tr>
			<td>Gas divider</td>
			<td>0.5</td>
		</tr>
	</tbody>
</table>
Table 2. Component Uncertainty. Independent component uncertainties used to quantify system uncertainty.
Overall, the system and its methods have proven beneficial in efforts to quantify accurately the methane emissions from various sources. The system is scalable and user friendly. The developed system has an uncertainty of &#177;4.4% compared to current commercial systems with an uncertainty of &#177;10% 74. With proper calibrations, this system can easily quantify leak rates up to 140 SCFM compared to current commercial systems that are capable of quantifying leaks up to 8 SCFM with full battery charges 64,74. While the system requires connection to house power, this offers advantages of consistent sample rates and sample rates much higher than current systems. The minimum detection limit of the current system is 0.24 g/hr or 3.0x10-3 SCFM. The user interface reduces post-processing requirements and reduces reporting efforts. In addition, the laser-based sensors are non-destructive to the leak sample, which allows for direct measurement of the sample with multiple analyzers 65. Laser based measurements also do not require separate sensors for ambient, small, and large leak concentrations or sensor transitions, which contribute to additional sources of inaccuracy. Future studies focus on continued optimization of the FFS and its user interface. Additional research is being conducted which combines experimental research data and computation fluid dynamics to develop additional best practices to ensure consistent and optimal measurement techniques.

Recent reports confirm the climate is changing because of human activities and further change is inevitable 1. Climate change occurs from an increase in greenhouse gases (GHG) concentration of the atmosphere. Carbon dioxide (CO2) and methane are the largest GHG contributors 2. CO2 and methane originate from both natural processes and human activities 3. Present atmospheric levels of CO2 and methane have respectively increased by 31% and 151% over the past two centuries, with the methane concentration increasing at a rate of 2% per year 4-6. The climate repercussions of methane and CO2 emissions depend upon the period considered as methane has a shorter atmospheric lifespan relative to CO2 7. Methane&#39;s atmospheric lifespan is 12-17 years, after which oxidization to CO2 occurs 8. The impact of methane is 72 times greater than CO2 in a 20-year period 9. On a mass basis, methane is 23 times more effective at trapping heat in the atmosphere than CO2 over a 100-year period 10. Methane and CO2 account for 10% and 82% of the total United States (U.S.) GHG emissions 11. Global methane emissions from anthropogenic sources are approximately 60% and the remaining are from natural sources 8, 10.
In 2009, non-combusted methane emissions between production wells and local distribution network corresponded to 2.4% of gross U.S. natural gas production (1.9-3.1% at a 95% confidence level) 12. Non-combusted methane emissions are not only harmful to the environment, but also represent a huge cost to natural gas companies 13. Analysts estimate that the natural gas industry loses in excess of $2 billion dollars per year because of methane leaks and venting 14. Non-combusted emissions are classified as fugitive or venting 15, 16. Fugitive refers to the unintentional release of gas from processes or equipment, such as valves, flanges, or fittings to ambient air 17, 18. Venting refers to the intentional release of gas from equipment or operation processes to ambient air, such as pneumatic actuators 19. At onshore oil and natural gas facilities, fugitive emissions account for ~30% of the total methane emissions 20. In 2011, the U.S. Environmental Protection Agency (EPA) estimates that more than 6 million metric tons of fugitive methane escaped from natural gas systems, which exceed the amount of GHG emissions (CO2-equivalent over a 100-year period), emitted by all U.S. iron and steel, cement, and aluminum manufacturing facilities combined 21.
A critical gap exists in the determination of the climate impact of natural gas due to the lack of accurate and reliable estimates of associated emissions. However, there is a consensus that fugitive methane emissions occur at every stage of the natural gas life cycle and further research in accurately measuring and reporting these values is important 19. Studies have reported fugitive emissions from specific sectors with results varying by up to twelve orders of magnitude 19, 22-28. The lack of recognized industry standards and a shortage of consistent regulations in the field of leak detection and leak quantification enable the use of a variety of testing methods and equipment, with the accuracy of some measurement techniques as high as &#177; 50% 29-35. Therefore, considerable uncertainty exists on the quantity of fugitive methane emitted over the natural gas life cycle 19, 28, 33, 36-39. Figure 1 illustrates the amount of variability in published literature on measured and estimated methane emissions associated with the natural gas life cycle. Figure 1 shows the average published fugitive methane emissions emitted as a percent of total natural gas production. If an average value was not given the average of the published range was taken. The standard deviation between the 23 studies is 3.54, with the lowest and highest values differing by 96.5%.
<img alt="Figure 1" src="/files/ftp_upload/54179/54179fig1.jpg" /> 
Figure 1. Fugitive Methane Emissions. Published averaged fugitive methane emissions emitted as a percent of total natural gas production 13, 27, 40-59. <a href="https://www.jove.com/files/ftp_upload/54179/54179fig1large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
Currently, the total amount of fugitive emissions is unclear due in part to measurement uncertainty and scaling techniques. Without accurate methane emission measurements, policymakers are unable to make informed choices on the matter. A review of current literature identified three primary methods for quantification of natural gas fugitive emissions: bagging, tracer gas, and a commercially available high flow sampler.
The bagging method involves placing an enclosure in the form of a &#39;bag&#39; or tent around a fugitive emission source 60. There are two variations of the bagging method. In one, a known flow rate of clean gas (typically inert) passes through the enclosure to create a well-mixed environment for measurement. Once equilibrium is reached, a gas sample is collected from the bag and measured. The fugitive emission rate is determined from the measured flow rate of clean gas through the enclosure and the steady-state methane concentration within the enclosure 61. Depending upon enclosure and leak size, the time required to reach the necessary steady state conditions for the leak rate measurement is between 15 to 20 min&#160;61. The bagging method can be applied on most accessible components. However, it may not be suitable for abnormally shaped components. This method type is capable of measuring leaks ranging in size from 0.28 cubic meters per minute (m3/min) to as large as 6.8 m3/min 60.The other bagging technique is known as calibrated bagging. Here, bags of known volume are sealed around a fugitive emission source. The fugitive emission rate is calculated based on the amount of time required for the expansion of the bag, and corrected to standard conditions.
Tracer gas methods quantify a fugitive emission rate based on the measured tracer gas concentration flowing through a fugitive source. Tracer gases commonly employed are helium, argon, nitrogen, sulfur hexafluoride, among others. The fugitive emission rate is determined from the ratio of a known release rate of tracer gas near the fugitive source, measurements of the downwind concentrations of tracer and fugitive source gas, and upwind baseline 24. The fugitive emission rate is only valid assuming identical dispersion and complete mixing for the two sources 62. This implies that the tracer is released near the fugitive source at a similar rate and height, and the downwind measurement is from well-mixed plumes. This method is time consuming and does not provide for component level granularity 63.
A commercially available high volume sampling system consists of a portable battery operated instrument packaged inside a backpack to quantify fugitive emission rates 64. The air surrounding the leak location is drawn into the sampler through a 1.5-inch inner diameter hose at a sufficiently high flow rate that it can be assumed that all of the leaking gas is being captured.
The sample flow rate is calculated with a venturi within the unit. For low concentrations of methane, 0.05-5% gas by volume, a catalyst methane sensor is used to measure concentration. This sensor is destructive to the methane and other hydrocarbons within the sample. For methane concentrations from 5-100% by volume, a thermal sensor is employed. The system uses a separate background sensor and probe which corrects the leak concentration relative to the background concentration. After the measurement is complete, the sample is exhausted back into the atmosphere away from the sampling area 64. This method can be applied on most accessible components, with the limitation of measurable flow rates up to eight standard cubic feet per minute (SCFM). This system is capable of testing up to 30 samples per hour. Recently, this system has been shown to have varied accuracy and issues regarding the transition from the catalytic sensor to the thermal sensor 65. Additionally, the system requires gas fractional analysis to correctly apply a response factor based on gas quality &#8212; it is not methane specific. The system has been widely used and may have attributed to discrepancies between top-down and bottom-up methods by under reporting methane emissions 65.
Due to limitations of these methods and systems, a new quantification system was developed. The FFS employs the same design concept as dilution systems used in automotive emissions certification 66-68. The FFS consists of a hose that feeds an explosive-proof blower that exhausts the leak and dilution air sample through a mass airflow sensor (MAF) and sample probe. The sample probe is connected to a laser based methane analyzer through a sampling tube. The analyzers uses cavity enhanced absorption for measurement of CH4, CO2, and H2O. The analyzer is capable of measuring CH4 from 0% to 10% by volume, CO2 from 0 to 20,000 ppm, and H2O from 0 to 70,000 ppm. Repeatability/precision (1-sigma) for this configuration is &#60;0.6 ppb of CH4, &#60;100 ppb CO2, and &#60;35 ppm for H2O 69. The sample is drawn from the stream at a constant volumetric rate. The system is instrumented with data logging equipment. Figure 2 illustrates the schematic of the FFS. Prior to operating the FFS, the grounding connection on the sampler hose is attached to a surface that allows the system to be grounded. This is a preventive action to dissipate any static charge on the end of the hose, which could result from airflow through the hose. Data acquisition occurs on either a smart phone, tablet, or laptop computer. Software was developed for data collection, processing, and reporting. Figure 3 provides a brief overview of the user interfaces for the following protocols.
<img alt="Figure 2" src="/files/ftp_upload/54179/54179fig2.jpg" /> 
Figure 2. FFS Schematic and Image. Left - FFS schematic and right - portable FFS during Compressed Natural Gas (CNG) station audit. <a href="https://www.jove.com/files/ftp_upload/54179/54179fig2large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 3" src="/files/ftp_upload/54179/54179fig3.jpg" /> 
Figure 3. Detection and Quantification Program Overview. Brief overview of the steps and user prompts for calibrations, recovery tests, and leak quantification. <a href="https://www.jove.com/files/ftp_upload/54179/54179fig3large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>

<table><tbody><tr><td>Abaco DBX 97 mm&amp;nbsp;</td><td>Abaco Performance, LLC</td><td>http://www.abacoperformance.com/products.htm</td><td>mass air flow sensor</td></tr><tr><td>Ultraportable Greenhouse Gas Analyzer</td><td>Los Gatos Research</td><td>http://www.lgrinc.com/analyzers/ultraportable-greenhouse-gas-analyzer/</td><td>methane, CO&lt;sub&gt;2&lt;/sub&gt;, and water sensor</td></tr><tr><td>3AA20 Fume Exhauster&amp;nbsp;</td><td>Daytona</td><td>http://www.sustainablesupply.com/Dayton-3AA20-Exhauster-Fume-Smoke-p/w267066.htm?gclid=CI2Dm9ffrcgCFUYTHwodyusFRg&amp;amp;CAWELAID=1307486526</td><td>blower/dilutor</td></tr><tr><td>Eagle II&amp;nbsp;</td><td>RKI Instruments</td><td>http://www.rkiinstruments.com/pdf/eagle2brochure.pdf</td><td>Handheld detector</td></tr><tr><td>MCR 50&amp;nbsp;</td><td>Alicat Scientific</td><td>http://www.alicat.com/</td><td>calibrated on methane</td></tr><tr><td>Laminar Flow Element, Model Number: Z50MC2-6, Serial Number 707230-Y1</td><td>Meriam</td><td>http://www.meriam.com/product-category/laminar-flow-element/</td><td>calibrated on air</td></tr><tr><td>K-Type thermocouple</td><td>Omega</td><td>http://www.omega.com/</td><td></td></tr><tr><td>PTE-1 Calibrator</td><td>Heise</td><td>http://www.heise.com/products/calibrators/</td><td>handheld unit for use with Dressor modules</td></tr><tr><td>Model HQS-2&amp;nbsp;</td><td>Dresser/Ashcroft</td><td>http://www.ashcroft.eu/download/data%20sheet/englisch/MODULE_E.pdf</td><td>absolute pressure module</td></tr><tr><td>Model HQS-1&amp;nbsp;</td><td>Dresser/Ashcroft</td><td>http://www.ashcroft.eu/download/data%20sheet/englisch/MODULE_E.pdf</td><td>differential pressure module</td></tr><tr><td>Gas Divider - SGD-710C</td><td>Horiba</td><td>http://www.horiba.com/us/en/</td><td>calibrated gas divider</td></tr><tr><td>Methane (99.9%)</td><td>Mathenson TriGas</td><td>http://www.mathesongas.com/</td><td>pure methane for gas recovery test</td></tr><tr><td>Methane (&amp;#177;1%) 2.5%</td><td>Mathenson TriGas</td><td>http://www.mathesongas.com/</td><td>high concentration</td></tr><tr><td>Methane (&amp;#177;1%) 2,010&amp;nbsp;ppm</td><td>Mathenson TriGas</td><td>http://www.mathesongas.com/</td><td>low concentration</td></tr><tr><td>Ultra High Purity Nitrogen (UPHN)</td><td>Mathenson TriGas</td><td>http://www.mathesongas.com/</td><td>99.9% nitrogent gas</td></tr><tr><td>10 Liter Tedlar Bag</td><td>Dupont</td><td>http://www.dupont.com/products-and-services/membranes-films/pvf-films/brands/tedlar-pvf-films/uses-and-applications/tedlar-gas-sample-bag-applications.html</td><td>used for bag samples for alternative gas sampling</td></tr><tr><td>PET-7018Z</td><td>ICP DAS USA</td><td>http://www.icpdas-usa.com/pet_7018z.html</td><td>DAQ unit</td></tr><tr><td>Edgetech Dew Prime Hyrgrometer</td><td>Edgetech Instruments</td><td>http://www.edgetechinstruments.com/moisture-humidity</td><td>hygrometer for flowbench</td></tr><tr><td>Stainless steel Swagelok fittings (1/4 inch)</td><td>Swagelok</td><td>https://www.swagelok.com/products/fittings.aspx</td><td>tee and other fittings</td></tr><tr><td>PTFE Tubing</td><td>McMaster-Carr</td><td>http://www.mcmaster.com/#standard-hollow-tubing-(made-with-teflon-ptfe)/=z8xrzl</td><td>tubing for sampling and calibration</td></tr><tr><td>FLIR GF 320</td><td>FLIR</td><td>http://www.flir.com/ogi/display/?id=55671</td><td>infrared camera</td></tr><tr><td>CGA 580 Regulator</td><td>Airgas</td><td>http://airgas.com/category/_/N-1z13vaq</td><td>UHPN regulator</td></tr><tr><td>CGA 350 Regulator</td><td>Airgas</td><td>http://airgas.com/category/_/N-1z13vaq</td><td>Methane in nitrogen regulator</td></tr><tr><td>Leak detection solution (Snoop)</td><td>Swagelok</td><td>https://www.swagelok.com/search/find_products_home.aspx?show_results=Y&amp;amp;item=5e208092-ed6c-4251-9202-ed8a2aae5811</td><td>bubble solution for non-leak verification</td></tr></tbody></table>

design and use of a full flow sampling system (ffs) for the quantification of methane emissions

The use of natural gas continues to grow with increased discovery and production of unconventional shale resources. At the same time, the natural gas industry faces continued scrutiny for methane emissions from across the supply chain, due to methane&#39;s relatively high global warming potential (25-84x that of carbon dioxide, according to the Energy Information Administration). Currently, a variety of techniques of varied uncertainties exists to measure or estimate methane emissions from components or facilities. Currently, only one commercial system is available for quantification of component level emissions and recent reports have highlighted its weaknesses.
In order to improve accuracy and increase measurement flexibility, we have designed, developed, and implemented a novel full flow sampling system (FFS) for quantification of methane emissions and greenhouse gases based on transportation emissions measurement principles. The FFS is a modular system that consists of an explosive-proof blower(s), mass airflow sensor(s) (MAF), thermocouple, sample probe, constant volume sampling pump, laser based greenhouse gas sensor, data acquisition device, and analysis software. Dependent upon the blower and hose configuration employed, the current FFS is able to achieve a flow rate ranging from 40 to 1,500 standard cubic feet per minute (SCFM). Utilization of laser-based sensors mitigates interference from higher hydrocarbons (C2+). Co-measurement of water vapor allows for humidity correction. The system is portable, with multiple configurations for a variety of applications ranging from being carried by a person to being mounted in a hand drawn cart, on-road vehicle bed, or from the bed of utility terrain vehicles (UTVs). The FFS is able to quantify methane emission rates with a relative uncertainty of &#177; 4.4%. The FFS has proven, real world operation for the quantification of methane emissions occurring in conventional and remote facilities.

Multiple FFS were developed and used to quantify a variety of methane emission sources. Two major studies included the Environmental Defense Fund&#39;s Heavy-Duty Natural Gas Vehicles Pump to Wheels (PTW) study and the Barnett Coordinated Campaign (BCC). The PTW study focused on quantification of methane emissions from heavy-duty natural gas vehicle fuel systems, engine crankcases, compressed natural gas tanks, liquefied natural gas tanks, fuel station equipment, nozzles, and other leaks.
Multiple FFS systems were used during the BCC, which brought together leading experts from academic and research facilities from around the country to collect methane emissions data across the natural gas supply chain (production, gathering and processing, transmission and storage and local distribution) through a combination of aircraft, vehicle, and ground-based measurements. We conducted direct source quantification of methane emissions at natural gas compressor stations and storage facilities using the developed methodology and FFS system. A portion of the results from the Barnett Shale study relating to measurements obtained through the employment of the FFS has been presented and published at peer reviewed conferences and scientific journals 70-72.
For both the PTW and BCC, we employed methane leak detection equipment to survey site components including valves, tubing/piping, and other components that carried or held natural gas. A leak was detected with a hand held methane detector. This hand held detector aided in the identification of the leak location by identifying an increased methane concentration above background. Once a leak location was detected that surpassed the concentration threshold, researchers used the FFS to quantify the leak rate. The FFS leak sample was collected through a hose attached to the inlet side of a blower. The sample passed through a certified explosion proof blower where it was exhausted through a piping system that contained a MAF and methane sensor. The FFS system was able to sample at flow rates from 40 to 1,500 SCFM dependent upon the system configuration. Using the measured sample flow rate and methane concentration, the leak rate in SCFM or g/hr was calculated.
Calibration Data
For calibration, a constant flow was established through the system. The pressure drop across the LFE was obtained through the measurement of the differential pressure between the high-pressure port and the low-pressure port on the LFE. The absolute pressure was recorded from the high-pressure port of the differential measurement line. Calibration pressures were measured and recorded with a combined differential/absolute pressure meter. The handheld unit used two modules, one for absolute pressure, and one for differential pressure. The absolute pressure module was a capable of measuring 0-30 PSI absolute with an uncertainty of 0.025%. The differential pressure module was a capable of measuring from 0 to 10 inches of water with an uncertainty of 0.06%. The temperature of the gas sample was measured prior to the LFE using a K-Type thermocouple with an uncertainty of &#177;1.1 &#176;C or 0.4%. The voltage output from the MAF was recorded via an analog data acquisition card. The flow rate was varied with a variable restrictor valve on the inlet of the blower. Calibrations were performed on the MAF for various flow rates, ranging up to 1,500 SCFM.
As a constant flow rate of air passed through both the LFE and MAF, the pressure differential, sample temperature, absolute pressure, and MAF voltage were recorded simultaneously. The pressure differential across the LFE, sample temperature, and absolute pressure were used to calculate the actual volumetric flow rate through the LFE using coefficients provided by the manufacturer. The actual volumetric flow rate was converted to standard volumetric flow. The standard volumetric flow rate through the LFE was related to the voltage obtained from the MAF, as shown in Figure 4.
<img alt="Figure 4" src="/files/ftp_upload/54179/54179fig4.jpg" /> 
Figure 4. MAF Output Signal Calibration. Multipoint calibration of the MAF with a NIST traceable LFE (see Sections 1 to 1.7). <a href="https://www.jove.com/files/ftp_upload/54179/54179fig4large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
A least-squares regression was performed on the data set to determine the best-fit coefficients of the equation and to calculate the equation&#39;s regression statistics, R2, to examine correlation between the data sets. Once the equation was developed, to relate the MAF voltage to the flow rate through the LFE, a comparison was made between the actual flow rate and the measured flow rate of the MAF. This is shown in Figure 5.
<img alt="Figure 5" src="/files/ftp_upload/54179/54179fig5.jpg" /> 
Figure 5. MAF Flow Rate Correlation. MAF measured flow rate plotted against the LFE actual volumetric flow rate (see Sections 1.8). <a href="https://www.jove.com/files/ftp_upload/54179/54179fig5large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
The calibration of the methane sensor with a 24,730-ppm methane gas cylinder is shown in Figure 6. The average deviation from the actual methane concentration after the external correction was applied was 0.7%. The largest deviation from the actual methane concentration after the external correction was applied was 1.9%.
<img alt="Figure 6" src="/files/ftp_upload/54179/54179fig6.jpg" /> 
Figure 6. Methane Sensor Calibration/Verification. External verification of the methane sensor using a calibrated gas divided and NIST traceable bottled methane (see Section 2). <a href="https://www.jove.com/files/ftp_upload/54179/54179fig6large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
After the calibration curves had been obtained and applied, verification of the entire system was performed by completing a gas recovery test. In which a known mass of methane was injected into the system using a methane calibrated MFC and a comparison made between the mass indicated by the system to the true mass injected. This procedure was based on the common practice of propane injections required by the Code of Federal Regulations for ensuring the capture and measurement ability of full flow dilution tunnels where a known volume of hydrocarbon emission are injected into the measurement system using an independently calibrated device and the recovery ability of the system is verified. The controlling MFC was calibrated on methane. The MFC was set at two flow rates of 20 and 30 SLPM of 99.9% pure methane. The results are presented in Table 1 for a system flow rate of 140 SCFM. It was shown that in both cases the FFS system measured values were within the expected 4.4%. The average error in the two measurements was +2.2%.
<table fo:keep-together.within-page="1">
	<tbody>
		<tr>
			<td>MFC Setpoint</td>
			<td>FFS Recovery</td>
			<td>Recovery Error</td>
		</tr>
		<tr>
			<td>SLPM</td>
			<td>SLPM</td>
			<td>%</td>
		</tr>
		<tr>
			<td>20</td>
			<td>20.3</td>
			<td>1.70%</td>
		</tr>
		<tr>
			<td>30</td>
			<td>30.8</td>
			<td>2.7</td>
		</tr>
		<tr>
			<td colspan="2">Average</td>
			<td>2.20%</td>
		</tr>
	</tbody>
</table>
Table 1. FFS Recovery Results. Methane recovery tests at two different simulated leak rates.
In Field Data Collection
Continuous Leak Source
Figure 6 illustrates an example of a continuous leak sources. Figure 7 can be divided into 4 separate regions, a-d. These include the following portions: background, approaching leak source, leak capture, and retreating from the leak source. Leak quantification occurs during section c. Upon review, the second repeated measurement of the same leak occurs after section d. Figure 8 shows the leak as viewed from infrared camera - the left shows the methane plume dispersing naturally - the right shows that the FFS collects all of the leak plus additional dilution air.
<img alt="Figure 7" src="/files/ftp_upload/54179/54179fig7.jpg" /> 
Figure 7. Conventional Continuous Leak. Continuous leak source time trace showing the various measurement sections (a: background, b: approaching the leak, c: average leak rate, d: retreating from leak) (see Sections 5 - 5.6). <a href="https://www.jove.com/files/ftp_upload/54179/54179fig7large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 8" src="/files/ftp_upload/54179/54179fig8.jpg" /> 
Figure 8. Infrared Image of Leak. Left - leaking fitting and right - captured/quantified leak from the same fitting (see Section 4.6). <a href="https://www.jove.com/files/ftp_upload/54179/54179fig8large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
Intermittent Leak Source 
The total mass associated with a certain event was obtained from the concentration-time profile through the application of numerical integration. In order to circumvent some of the inefficiencies associated with the trapezoidal rule, an adaptive composite Simpson&#39;s rule was employed. This adaptive quadrature type method allows for automatic step size adjustments in regions of sharp variations 73.
The need for numerical integration of the collected data was applicable for intermittent events, such as Figure 9 illustrates an example of an intermittent source of methane emissions. This example was for a vehicle-refueling event. Background is shown from 150-240 sec&#160;and from 425 sec&#160;until the end. This particular event was for the refueling of a single liquefied natural gas (LNG) tank. The leak rate was integrated to determine the total mass emitted (9.5 g).
<img alt="Figure 9" src="/files/ftp_upload/54179/54179fig9.jpg" /> 
Figure 9. Intermittent Leak. Intermittent &#39;leak&#39; source from a vehicle-refueling event (concentration [ppm], dilution flow rate [scfm], leak rate [g/hr]) (see Section 5). <a href="https://www.jove.com/files/ftp_upload/54179/54179fig9large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
Aggregated Source 
Due to multiple sources being in tight proximity and enclosed by a covering, the compressor unit was aggregated and treated as a single source for leak quantification. Figure 10 shows an example of measuring the methane emissions from an aggregated source. These data were collected from a time-fill CNG compressor housing. The compressor housing was measured continuously for approximately 119 min. The compressor unit encountered did display a small amount of variability. Variations in leak rate and methane concentration were due to pressure fluctuations and variable leaks from compressor seals. For aggregated sources, data were collected for extended periods and the average leak rate was calculated.
<img alt="Figure 10" src="/files/ftp_upload/54179/54179fig10.jpg" /> 
Figure 10. Aggregate Example. Leak rate, flow, and concentration data from an aggregated time fill CNG compressor housing (compressors and fans off) (see Section 5.7). <a href="https://www.jove.com/files/ftp_upload/54179/54179fig10large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>

Watch this Scientific Journal Video about Design and Use of a Full Flow Sampling System FFS for the Quantification of Methane Emissions at JoVE.com

Design and Use of a Full Flow Sampling System FFS for the Quantification of Methane Emissions | Engineering | Video

Design and Use of a Full Flow Sampling System FFS for the Quantification of Methane Emissions

We have designed, developed, and implemented a novel full flow sampling system (FFS) for quantification of methane emissions and greenhouse gases from across the natural gas supply chain.

Design and Use of a Full Flow Sampling System (FFS) for the Quantification of Methane Emissions

The use of natural gas continues to grow with increased discovery and production of unconventional shale resources. At the same time, the natural gas ...

design-use-full-flow-sampling-system-ffs-for-quantification-methane

Education

Research

JoVE Core

JoVE Journal

Chemistry

Biology

Engineering

Ecology

Biodiversity and Conservation

Introduction: Matter and Measurement

SCIENTISTS IN ACTION

16.7K Views.  West Virginia University. We have designed, developed, and implemented a novel full flow sampling system (FFS) for quantification of methane emissions and greenhouse gases from across the natural gas supply chain.

Video: Design and Use of a Full Flow Sampling System FFS for the Quantification of Methane Emissions

The Use of an Automated System (GreenFeed) to Monitor Enteric Methane and Carbon Dioxide Emissions from Ruminant Animals

Ruminant animals (domesticated or wild) emit methane (CH4) through enteric fermentation in their digestive tract and from decomposition of manure during storage. These processes are the major sources of greenhouse gas (GHG) emissions from animal production systems. Techniques for measuring enteric CH4 vary from direct measurements (respiration chambers, which are highly accurate, but with limited applicability) to various indirect methods (sniffers, laser technology, which are practical, but with variable accuracy). The sulfur hexafluoride (SF6)&#160;tracer gas method is commonly used to measure enteric CH4 production by animal scientists and more recently, application of an Automated Head-Chamber System (AHCS) (GreenFeed, C-Lock, Inc., Rapid City, SD), which is the focus of this experiment, has been growing. AHCS is an automated system to monitor CH4 and carbon dioxide (CO2) mass fluxes from the breath of ruminant animals. In a typical AHCS operation, small quantities of baiting feed are dispensed to individual animals to lure them to AHCS multiple times daily. As the animal visits AHCS, a fan system pulls air past the animal&#8217;s muzzle into an intake manifold, and through an air collection pipe where continuous airflow rates are measured. A sub-sample of air is pumped out of the pipe into non-dispersive infra-red sensors for continuous measurement of CH4 and CO2 concentrations. Field comparisons of AHCS to respiration chambers or SF6 have demonstrated that AHCS produces repeatable and accurate CH4 emission results, provided that animal visits to AHCS are sufficient so emission estimates are representative of the diurnal rhythm of rumen gas production. Here, we demonstrate the use of AHCS to measure CO2 and CH4 fluxes from dairy cows given a control diet or a diet supplemented with technical-grade cashew nut shell liquid.

The Use of an Automated System GreenFeed to Monitor Enteric Methane and Carbon Dioxide Emissions from Ruminant Animals

Accuracy and precision of the techniques used to measure methane emissions from ruminant animals are critically important for the success of greenhouse gas mitigation efforts. This manuscript describes the principles and operation of an automated system to monitor methane and carbon dioxide mass fluxes from the breath of ruminant animals.

Ruminant animals (domesticated or wild) emit methane (CH4) through enteric fermentation in their digestive tract and from decomposition of manure during ...

Environment

Calibrated Passive Sampling - Multi-plot Field Measurements of NH3 Emissions with a Combination of Dynamic Tube Method and Passive Samplers

Agricultural ammonia (NH3) emissions (90% of total EU emissions) are responsible for about 45% airborne eutrophication, 31% soil acidification and 12% fine dust formation within the EU15. But NH3 emissions also mean a considerable loss of nutrients. Many studies on NH3 emission from organic and mineral fertilizer application have been performed in recent decades. Nevertheless, research related to NH3 emissions after application fertilizers is still limited in particular with respect to relationships to emissions, fertilizer type, site conditions and crop growth. Due to the variable response of crops to treatments, effects can only be validated in experimental designs including field replication for statistical testing. The dominating ammonia loss methods yielding quantitative emissions require large field areas, expensive equipment or current supply, which restricts their application in replicated field trials. This protocol describes a new methodology for the measurement of NH3 emissions on many plots linking a simple semi-quantitative measuring method used in all plots, with a quantitative method by simultaneous measurements using both methods on selected plots. As a semi-quantitative measurement method passive samplers are used. The second method is a dynamic chamber method (Dynamic Tube Method) to obtain a transfer quotient, which converts the semi-quantitative losses of the passive sampler to quantitative losses (kg nitrogen ha-1). The principle underlying this approach is that passive samplers placed in a homogeneous experimental field have the same NH3 absorption behavior under identical environmental conditions. Therefore, a transfer co-efficient obtained from single passive samplers can be used to scale the values of all passive samplers used in the same field trial. The method proved valid under a wide range of experimental conditions and is recommended to be used under conditions with bare soil or small canopies (&#60;0.3 m). Results obtained from experiments with taller plants should be treated more carefully.

Calibrated Passive Sampling - Multi-plot Field Measurements of NH3 Emissions with a Combination of Dynamic Tube Method and Passive Samplers

Ammonia emissions are a major threat to the environment by eutrophication, soil acidification and fine particle formation and stem mainly from agricultural sources. This method allows ammonia loss measurements in replicated field trials enabling statistical analysis of emissions and of relationships between crop development and emissions.

Agricultural ammonia (NH3) emissions (90% of total EU emissions) are responsible for about 45% airborne eutrophication, 31% soil acidification and 12% ...

Quantitative Detection of Trace Explosive Vapors by Programmed Temperature Desorption Gas Chromatography-Electron Capture Detector

The direct liquid deposition of solution standards onto sorbent-filled thermal desorption tubes is used for the quantitative analysis of trace explosive vapor samples. The direct liquid deposition method yields a higher fidelity between the analysis of vapor samples and the analysis of solution standards than using separate injection methods for vapors and solutions, i.e., samples collected on vapor collection tubes and standards prepared in solution vials. Additionally, the method can account for instrumentation losses, which makes it ideal for minimizing variability and quantitative trace chemical detection. Gas chromatography with an electron capture detector is an instrumentation configuration sensitive to nitro-energetics, such as TNT and RDX, due to their relatively high electron affinity. However, vapor quantitation of these compounds is difficult without viable vapor standards. Thus, we eliminate the requirement for vapor standards by combining the sensitivity of the instrumentation with a direct liquid deposition protocol to analyze trace explosive vapor samples.

Trace explosive vapors of TNT and RDX collected on sorbent-filled thermal desorption tubes were analyzed using a programmed temperature desorption system coupled to GC with an electron capture detector. The instrumental analysis is combined with direct liquid deposition method to reduce sample variability and account for instrumentation drift and losses.

The direct liquid deposition of solution standards onto sorbent-filled thermal desorption tubes is used for the quantitative analysis of trace explosive ...

Convergent Polishing: A Simple, Rapid, Full Aperture Polishing Process of High Quality Optical Flats &amp; Spheres

Convergent Polishing is a novel polishing system and method for finishing flat and spherical glass optics in which a workpiece, independent of its initial shape (i.e., surface figure), will converge to final surface figure with excellent surface quality under a fixed, unchanging set of polishing parameters in a single polishing iteration. In contrast, conventional full aperture polishing methods require multiple, often long, iterative cycles involving polishing, metrology and process changes to achieve the desired surface figure. The Convergent Polishing process is based on the concept of workpiece-lap height mismatch resulting in pressure differential that decreases with removal and results in the workpiece converging to the shape of the lap. The successful implementation of the Convergent Polishing process is a result of the combination of a number of technologies to remove all sources of non-uniform spatial material removal (except for workpiece-lap mismatch) for surface figure convergence and to reduce the number of rogue particles in the system for low scratch densities and low roughness. The Convergent Polishing process has been demonstrated for the fabrication of both flats and spheres of various shapes, sizes, and aspect ratios on various glass materials. The practical impact is that high quality optical components can be fabricated more rapidly, more repeatedly, with less metrology, and with less labor, resulting in lower unit costs. In this study, the Convergent Polishing protocol is specifically described for fabricating 26.5 cm square fused silica flats from a fine ground surface to a polished ~&#955;/2 surface figure after polishing 4 hr per surface on a 81 cm diameter polisher.

Convergent Polishing: A Simple, Rapid, Full Aperture Polishing Process of High Quality Optical Flats & Spheres

A novel optical polishing process, called &#8220;Convergent Polishing&#8221;, which enables faster, lower cost polishing, is described. Unlike conventional polishing processes, Convergent Polishing allows a glass workpiece to be polished in a single iteration and with high surface quality to its final surface figure without requiring changes to polishing parameters.

Convergent Polishing is a novel polishing system and method for finishing flat and spherical glass optics in which a workpiece, independent of its initial ...

Characterizing Far-infrared Laser Emissions and the Measurement of Their Frequencies

The generation and subsequent measurement of far-infrared radiation has found numerous applications in high-resolution spectroscopy, radio astronomy, and Terahertz imaging. For about 45 years, the generation of coherent, far-infrared radiation has been accomplished using the optically pumped molecular laser. Once far-infrared laser radiation is detected, the frequencies of these laser emissions are measured using a three-laser heterodyne technique. With this technique, the unknown frequency from the optically pumped molecular laser is mixed with the difference frequency between two stabilized, infrared reference frequencies. These reference frequencies are generated by independent carbon dioxide lasers, each stabilized using the fluorescence signal from an external, low pressure reference cell. The resulting beat between the known and unknown laser frequencies is monitored by a metal-insulator-metal point contact diode detector whose output is observed on a spectrum analyzer. The beat frequency between these laser emissions is subsequently measured and combined with the known reference frequencies to extrapolate the unknown far-infrared laser frequency. The resulting one-sigma fractional uncertainty for laser frequencies measured with this technique is &#177; 5 parts in 107. Accurately determining the frequency of far-infrared laser emissions is critical as they are often used as a reference for other measurements, as in the high-resolution spectroscopic investigations of free radicals using laser magnetic resonance. As part of this investigation, difluoromethane, CH2F2, was used as the far-infrared laser medium. In all, eight far-infrared laser frequencies were measured for the first time with frequencies ranging from 0.359 to 1.273 THz. Three of these laser emissions were discovered during this investigation and are reported with their optimal operating pressure, polarization with respect to the CO2 pump laser, and strength.

We describe the generation of far-infrared radiation using an optically pumped molecular laser along with the measurement of their frequencies with heterodyne techniques. The experimental system and techniques are demonstrated using difluoromethane (CH2F2) as the laser medium whose results include three new laser emissions and eight measured laser frequencies.

The generation and subsequent measurement of far-infrared radiation has found numerous applications in high-resolution spectroscopy, radio astronomy, and ...

Characterization of Full Set Material Constants and Their Temperature Dependence for Piezoelectric Materials Using Resonant Ultrasound Spectroscopy

During the operation of high power electromechanical devices, a temperature rise is unavoidable due to mechanical and electrical losses, causing the degradation of device performance. In order to evaluate such degradations using computer simulations, full matrix material properties at elevated temperatures are needed as inputs. It is extremely difficult to measure such data for ferroelectric materials due to their strong anisotropic nature and property variation among samples of different geometries. Because the degree of depolarization is boundary condition dependent, data obtained by the IEEE (Institute of Electrical and Electronics Engineers) impedance resonance technique, which requires several samples with drastically different geometries, usually lack self-consistency. The resonant ultrasound spectroscopy (RUS) technique allows the full set material constants to be measured using only one sample, which can eliminate errors caused by sample to sample variation. A detailed RUS procedure is demonstrated here using a lead zirconate titanate (PZT-4) piezoceramic sample. In the example, the complete set of material constants was measured from room temperature to 120 &#176;C. Measured free dielectric constants <img alt="Equation 1" src="/files/ftp_upload/53461/image001.jpg" /> and&#160;<img alt="Equation 2" src="/files/ftp_upload/53461/image002.jpg" /> were compared with calculated ones based on the measured full set data, and piezoelectric constants d15 and d33 were also calculated using different formulas. Excellent agreement was found in the entire range of temperatures, which confirmed the self-consistency of the data set obtained by the RUS.

This protocol describes the procedure of measuring the temperature dependence of the full set material constants of piezoelectric materials using resonant ultrasound spectroscopy (RUS).

During the operation of high power electromechanical devices, a temperature rise is unavoidable due to mechanical and electrical losses, causing the ...

Assessment of Methane and Nitrous Oxide Fluxes from Paddy Field by Means of Static Closed Chambers Maintaining Plants Within Headspace

This protocol describes the measurement of greenhouse gas (GHG) emissions from paddy soils using the static closed chamber technique. This method is based on the diffusion theory. A known volume of air overlaying a defined soil area is enclosed within a parallelepiped cover (named &#34;chamber&#34;), for a defined period of time. During this enclosure period, gases (methane (CH4) and nitrous oxide (N2O)) move from soil pore air near their microbial source (i.e., methanogens, nitrifiers, denitrifiers) to the chamber headspace, following a natural concentration gradient. Fluxes are then estimated from chamber headspace concentration variations sampled at regular intervals throughout the enclosure and then analyzed with gas chromatography. Among the techniques available for GHG measurement, the static closed chamber method is suitable for plot experiments, as it does not require large homogenously treated soil areas. Furthermore, it is manageable with limited resources and can identify relationships among ecosystem properties, processes, and fluxes, especially when combined with GHG driving force measurements. Nevertheless, with respect to the micrometeorological method, it causes a minimal but still unavoidable soil disturbance, and allows a minor temporal resolution. Several phases are key to the method implementation: i) chamber design and deployment, ii) sample handling and analyses, and iii) flux estimation. Technique implementation success in paddy fields demands adjustments for field flooding during much of the cropping cycle, and for rice plant maintenance within the chamber headspace during measurements. Therefore, the additional elements to be considered with respect to the usual application of non-flooded agricultural soils consist of devices for: i) avoiding any unintended water disturbance that could overestimate fluxes, and ii) including rice plants within the chamber headspace to fully consider gases emitted through aerenchyma transportation.

The overall goal of this protocol is to measure greenhouse gas emissions from paddy fields using the static closed chamber technique. The measurement system needs specific adjustments due to the presence of both a permanent water layer in the field and of the plants within the chamber headspace.

This protocol describes the measurement of greenhouse gas (GHG) emissions from paddy soils using the static closed chamber technique. This method is based ...

Combustion Chemistry of Fuels: Quantitative Speciation Data Obtained from an Atmospheric High-temperature Flow Reactor with Coupled Molecular-beam Mass Spectrometer

This manuscript describes a high-temperature flow reactor experiment coupled to the powerful molecular beam mass spectrometry (MBMS) technique. This flexible tool offers a detailed observation of chemical gas-phase kinetics in reacting flows under well-controlled conditions. The vast range of operating conditions available in a laminar flow reactor enables access to extraordinary combustion applications that are typically not achievable by flame experiments. These include rich conditions at high temperatures relevant for gasification processes, the peroxy chemistry governing the low temperature oxidation regime or investigations of complex technical fuels. The presented setup allows measurements of quantitative speciation data for reaction model validation of combustion, gasification and pyrolysis processes, while enabling a systematic general understanding of the reaction chemistry. Validation of kinetic reaction models is generally performed by investigating combustion processes of pure compounds. The flow reactor has been enhanced to be suitable for technical fuels (e.g. multi-component mixtures like Jet A-1) to allow for phenomenological analysis of occurring combustion intermediates like soot precursors or pollutants. The controlled and comparable boundary conditions provided by the experimental design allow for predictions of pollutant formation tendencies. Cold reactants are fed premixed into the reactor that are highly diluted (in around 99 vol% in Ar) in order to suppress self-sustaining combustion reactions. The laminar flowing reactant mixture passes through a known temperature field, while the gas composition is determined at the reactors exhaust as a function of the oven temperature. The flow reactor is operated at atmospheric pressures with temperatures up to 1,800 K. The measurements themselves are performed by decreasing the temperature monotonically at a rate of -200 K/h. With the sensitive MBMS technique, detailed speciation data is acquired and quantified for almost all chemical species in the reactive process, including radical species.

An investigation of the oxidative combustion chemistry of novel biofuels, fuel components, or jet fuels by comparison of quantitative speciation data is presented. The data can be used for kinetic model validation and enables fuel assessment strategies.This manuscript describes the atmospheric high-temperature flow reactor and demonstrates its capabilities.

This manuscript describes a high-temperature flow reactor experiment coupled to the powerful molecular beam mass spectrometry (MBMS) technique. This ...

Respirometry Protocol for Anaerobic Digestion of Food Waste and Sludge

Measuring Biomethane Potential of Food Scrap Waste Anaerobically Co&#45;Digested with Waste&#45;Activated Sludge Using Respirometry

The use of respirometry to study the biokinetics of microbiota treating wastewater or digesting wastewater sludges has become more prevalent over the last few decades. The use of respirometry to examine the biokinetics of anaerobic microbiota co-digesting organic waste streams such as wastewater sludge and food scrap is an area of active research. To date, no visualized protocol has been published on the topic. Accordingly, in this protocol, we configured a respirometer to measure methane production and flow rate over time using three different food-to-microorganism (F:M) ratios and food scrap waste and waste-activated sludge as substrates. The resulting data, coupled with substrate utilization measurements, provides the basis for understanding how different substrate concentrations influence the rate at which anaerobic microbiota produce methane. Additionally, this protocol presents a method to develop biokinetic parameters (e.g., methane production rate constant and yield). Others can use this respirometry protocol to examine organic degradation under anaerobic conditions and develop microbial parameters.

Author Spotlight: Advancing Anaerobic Microbiota Research Using a Novel Respirometry Protocol

This protocol describes a best practice for determining methane production and microbial kinetic parameters using respirometry for anaerobic microbiota co-digesting food scrap waste and waste-activated sludge.

The use of respirometry to study the biokinetics of microbiota treating wastewater or digesting wastewater sludges has become more prevalent over the last ...

A Practical and Low-Cost Setup to Measure Methane in Aqueous Samples

Measuring Dissolved Methane in Aquatic Ecosystems Using An Optical Spectroscopy Gas Analyzer

Measuring greenhouse gas (GHG) fluxes and pools in ecosystems are becoming increasingly common in ecological studies due to their relevance to climate change. With it, the need for analytical platforms adaptable to measuring different pools and fluxes within research groups also grows. This study aims to develop a procedure to use portable optical spectroscopy-based gas analyzers, originally designed and marketed for gas flux measurements, to measure GHG concentrations in aqueous samples. The protocol involves the traditional headspace equilibration technique followed by the injection of a headspace gas subsample into a chamber connected through a closed loop to the inlet and outlet ports of the gas analyzer. The chamber is fabricated from a generic mason jar and simple laboratory supplies, and it is an ideal solution for samples that may require pre-injection dilution. Methane concentrations measured with the chamber are tightly correlated (r2 &#62; 0.98) with concentrations determined separately through gas chromatography-flame ionization detection (GC-FID) on subsamples from the same vials. The procedure is particularly relevant for field studies in remote areas where chromatography equipment and supplies are not readily available, offering a practical, cheaper, and more efficient solution for measuring methane and other dissolved greenhouse gas concentrations in aquatic systems.

This study demonstrates an approach to measure methane gas concentrations in aqueous samples using portable optical analyzers coupled to an injection chamber in a closed loop. The results are similar to conventional gas chromatography, presenting a practical and low-cost alternative particularly suitable for remote field studies.

Measuring greenhouse gas (GHG) fluxes and pools in ecosystems are becoming increasingly common in ecological studies due to their relevance to climate ...

Design and Use of a Full Flow Sampling System (FFS) for the Quantification of Methane Emissions

Samenvatting

Meer video's verkennen