The non-salary component of the work was funded by the Commonwealth of Australia. The author from the University of Delaware gratefully acknowledges the support of the US National Science Foundation (Grant #1254540, Dr. Mary Toney, Program Director). The authors thank Mr. Mark Fitzgerald for his assistance with the electrophoretic deposition measurements.

1. Functionalization of CNTs and GNPs by Ultrasonic Ozonolysis
<ol>
	<li>Weigh the nanomaterials in a glove box inside a HEPA filter-equipped fume cupboard. Weigh the desired quantity of nanomaterials into a beaker. Transfer to a bottle and add ultrapure water to make a concentration of 1 g/L.</li>
	<li>Seal the bottle with a lid. Ultrasonicate in a standard ultrasonic bath (see Materials List; frequency: ~43 &#177;2 kHz; power: 60 W) to disperse the CNTs or GNPs. 
	NOTE: CAUTION. See the Work Health and Safety Notice above.</li>
	<li>Carefully pour the nanomaterial suspension into a reactor flask containing a magnetic stirrer bar. Attach a reactor flask lid with sufficient ports for the ozone and ultrasonic horn inlets and outlets. Place this on a stirring plate and turn on the magnetic stirrer by adjusting the dial to prevent the CNTs from settling out of suspension.</li>
	<li>Assemble the ultrasonic horn into the ultrasonic cell and check that the horn tip is in good condition. See Figure 1.</li>
</ol>
<img alt="Figure 1" src="/files/ftp_upload/55614/55614fig1.jpg" /> 
Figure 1: Ultrasonic Ozonolysis System. This schematic diagram illustrates how to connect the various elements of the ultrasonic ozonolysis system. <a href="http://cloudfront.jove.com/files/ftp_upload/55614/55614fig1large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<ol start="5">
	<li>Use silicone tubing to connect the reactor, the ultrasonic cell, and the peristaltic pump. Refer to Figure 1.</li>
	<li>Insert the ozone bubbler into the reactor and connect it to the ozone generator. 
	NOTE: CAUTION. See the Work Health and Safety Notice above.</li>
	<li>Connect the recirculating liquid cooler unit to a cooling coil (to cool the reactor) and to the ultrasonic cell-cooling jacket. Flip the switch to turn on the recirculating liquid cooling unit to cool the ozone reactor and ultrasonic cell. Ensure that the cooling liquid is flowing through both the ultrasonic cell and the reactor cooling bath.
	<ol>
		<li>Use a thermocouple connected to the ultrasonic horn control unit to measure the reactor temperature. Wait until the system has cooled to 5 &#176;C.</li>
	</ol>
	</li>
	<li>Place the reactor flask with the CNTs in position. Insert the ozone diffuser into the bottom of the reactor flask so that it is fully submerged. Ensure that the outlet tube to the ultrasonic cell is submerged at least 25 mm below the surface of the dispersion.
	<ol>
		<li>Connect the outlet tube from the reactor to the ozone destruct unit using the same silicone tubing as in the peristaltic pumping operation. Use of a water bubbler on the outlet side of the ozone destruct unit is optional, but it helps to capture any residual ozone and provides an indication that the ozone generator is connected and working correctly.</li>
	</ol>
	</li>
	<li>Turn on the oxygen supply to the ozone generator and adjust the valve to achieve a 0.5-L/min flow rate through the ozone generator.</li>
	<li>Turn on the ozone generator by flipping the switch. Allow it to run for 30-60 min prior to starting the pumping or the ultrasonication process.</li>
	<li>Turn on the peristaltic pump, adjust it to 0.67 Hz by turning the pump dial to a setting of approximately 5 or 6, and ensure that the CNT dispersion flows evenly through the cell.
	<ol>
		<li>Turn on the ultrasonic horn and adjust the power to 60 W by entering this value into the control module under the manual operation menu.</li>
		<li>At initial startup, ramp up the amplitude setting slowly to achieve the desired power output of 60 W. 
		NOTE: The ultrasonic horn operates at 20 kHz. The amplitude setting and power setting are usually of similar values, but upon initial startup, the amplitude setting may need to be slowly increased to achieve the desired power output of 60 W.</li>
	</ol>
	</li>
	<li>Observe the sonication process for at least 30 min to ensure stable pumping and ultrasonic horn operation.</li>
	<li>Monitor the flexible tubing in direct contact with the peristaltic pump mechanism for wear. Adjust the tube position at least every 2 h to ensure that the tubing maintains integrity. Replace the tubing for each separate carbon nanomaterial processing run.</li>
	<li>When the desired USO processing time has elapsed, press the switches to turn off the ozone generator, sonicator, and pump. Maintain stirring until the carbon nanomaterial dispersion is ready to be transferred to a sealed container for later use in electrophoretic deposition.
	<ol>
		<li>Wait around 1 h before transferring the dispersion to allow the ozone in solution to decompose.</li>
	</ol>
	</li>
	<li>If electrophoresis is not performed within 24 h of USO processing, sonicate the nanomaterial dispersion again to minimize the number of particles settling out of dispersion. Insert the sonic horn into the bottle of the carbon nanomaterial dispersion and sonicate (as above) for 30 min prior to use.</li>
</ol>
2. Electrophoresis
<ol>
	<li>Prepare three stainless-steel electrodes, 60 mm (L) x 25 mm (W), from 0.2-mm sheet material.
	<ol>
		<li>Abrade the electrodes using P1000 aluminum oxide sandpaper with ultrapure water as a lubricant. Following the abrasion, place the electrodes in the ultrasonic cleaning bath and clean them for 10 min in ultrapure water.</li>
	</ol>
	</li>
	<li>Place the electrode to be used for anodic deposition in a clean oven at 100 &#176;C and dry it for 10 min. Move the electrode to a desiccator and allow it to cool. Weigh the electrode on a four-figure analytical balance.</li>
	<li>Record the weight of the electrode to four decimal places as the uncoated weight in grams. Dry the remaining two electrodes and store them in the desiccator for use as cathodes for deposition.</li>
	<li>Using a suitable clamping arrangement (see Figure 2), such as a small vice and 10-mm non-conductive plastic spacers, assemble the electrodes, with the outer electrodes being used as the cathodes and the inner electrode as the anode.</li>
</ol>
<img alt="Figure 2" src="/files/ftp_upload/55614/55614fig2.jpg" /> 
Figure 2: Electrophoretic Deposition Cell. This schematic diagram illustrates the configuration of the electrophoretic deposition cell. <a href="http://cloudfront.jove.com/files/ftp_upload/55614/55614fig2large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<ol start="5">
	<li>Transfer 35 mL of carbon nanomaterial dispersion to a 50-mL beaker.</li>
	<li>Place the stainless-steel electrode fixture onto a retort stand and slowly lower the electrodes to the full depth of beaker. Attach the positive terminal of the DC power supply to the central stainless-steel anode. Attach the negative terminal of the DC power supply to the outer cathode. Connect the two outer cathodes using a lead with alligator clips.</li>
	<li>If accurate current measurements are required, connect a multimeter in series with the power supply unit and electrodes to enable monitoring during deposition.</li>
	<li>Manually adjust the current setting on the DC power supply to the maximum current (nominally, 2 A) and then the voltage to the required value for the studies, ensuring that the power supply output is turned off. Prepare a stopwatch and switch on the power supply for the required coating duration.</li>
	<li>For a typical coating experiment, adjust the voltage to 10 V, with the coating times ranging from 1 to 15 min. Switch off the DC power supply and then slowly raise the electrodes out of the dispersion, ensuring that the film is not disturbed.</li>
	<li>Disconnect the terminals from the electrodes and slowly invert the electrodes to a horizontal orientation to allow the film on the anode to dry evenly. After the moisture has evaporated from the film at room temperature, disassemble the electrode fixture and place the anode in the oven at 100 &#176;C to dry for 1 h.
	<ol>
		<li>Clamp and hang the anode in the oven to ensure that the film does not come into direct contact with any surfaces.</li>
	</ol>
	</li>
	<li>Place the film-coated anode in the desiccator and allow it to cool, then weigh it on a four-figure analytical balance. Record the weight to four decimal places. Subtract the weight of the uncoated anode to determine the mass of the deposited film.</li>
	<li>Photograph the coated anode. Use a suitable image processing package to accurately measure the area of the deposited film. Use the mass and area to record the areal density of the film in mg/cm2.</li>
	<li>Repeat the coating and weighing steps for each deposition time required to determine the rate of deposition of the carbon nanomaterial onto the stainless steel for the specific field strengths being used.</li>
</ol>
3. Chemical Characterization &#8211; X-ray Photoelectron Spectroscopy (XPS)15
<ol>
	<li>To prepare the samples for XPS analysis, drop-cast the aqueous CNT dispersions from the original 1 g/L dispersion.
	<ol>
		<li>Using a pipette, deposit a droplet of the dispersion on a stainless-steel disk and it allow to dry at room temperature. Repeat the process until a uniformly thick CNT coating of approximately 2 &#181;m in thickness is observed on the disk. Mount the stainless-steel disk onto sample stubs using double-sided conductive tape.</li>
	</ol>
	</li>
	<li>Insert the samples into the sample entry chamber and pump down to a vacuum of 5 x 10-7 Torr prior to transferring it to the main analysis chamber. Wait for the main chamber pressure to reach 5 x 10-9 Torr before positioning the sample and undertaking the analysis.</li>
	<li>To follow the typical operating conditions for the XPS measurements, use a monochromatic Al K&#945;,1 X-ray source operating at 150 W to illuminate an area of 700 &#181;m x 300 &#181;m. Detect photoelectrons at a 90&#176; take-off angle with respect to the sample surface.
	<ol>
		<li>Calibrate the spectrometer energy scale using the Au 4f7/2 photoelectron peak at a binding energy of 83.98 eV. 
		NOTE: The energy scale is adjusted in the instrument control software during the initial commissioning of the instrument. It is regularly checked following any maintenance operations by the spectroscopist in charge of the equipment and should not be altered by users.</li>
	</ol>
	</li>
	<li>Monitor the initial sample charge by positioning a 30-eV window over the C 1s region. Perform charge compensation by adjusting the electron flood gun parameters systematically to position the C 1s peak at 284.6 eV and to minimize the peak width at half the maximum peak intensity (FWHM).</li>
	<li>Conduct survey scans at 160 eV pass energy and 0.5 eV steps, with a dwell time of 0.1 s, in fixed analyzer transmission mode to identify the surface elemental species. Acquire region spectra at a 20 eV pass energy using 0.05-eV steps and a 0.2 s dwell. Use between 4 and 8 sweeps to improve the signal-to-noise ratio.
	<ol>
		<li>To quantify the spectra, use a Shirley background fit and sensitivity factors from a suitable elemental library16.</li>
	</ol>
	</li>
	<li>Deconvolve C 1s high-resolution X-ray photoelectron spectra to determine the different carbon-oxygen species present with USO treatment time15.
	<ol>
		<li>To accurately deconvolute the C 1s peak, perform an initial peak fit to the shape of graphitic carbon to ensure that the peak shape due to the sp2 bonding and the contributions from the low-energy &#960;-type shake-up satellites are maintained17. For all peak fitting, constrain the component binding energies and FWHM by &#177;0.1 eV and &#177;0.2 eV, respectively, and use a Gaussian/Lorentzian ratio of 30.</li>
		<li>Fit the graphite peak shape using six separate peaks. Maintain at fixed ratios the areas of each peak relative to the main graphite peak at 284.6 eV to maintain a consistent shape due to the graphitic component in the processed nanomaterial15,9,14.</li>
	</ol>
	</li>
</ol>
4. Structural Characterization &#8211; Raman Spectroscopy18
<ol>
	<li>Prepare the nanomaterials for Raman spectroscopic characterization by diluting the original dispersion with deionized water to achieve a 0.1 g/L concentration. Pipette 0.05 mL of dispersion onto a suitable polished-gold substrate. Allow the droplet to evaporate at room temperature to produce a thin carbon film on which to focus the Raman laser spot. 
	NOTE: The size of the gold substrate is incidental to the result when a large substrate is used, multiple specimens can be deposited on a single slide.</li>
	<li>Undertake Raman measurements with a 50X magnification objective lens using a dispersive confocal microscope and a 532 nm laser. Acquire the spectra between 3,500 and 50 cm-1 at a resolution of 2 cm-1. Use a 50 &#181;m pinhole aperture with a laser energy between 1 and 10 mW, using the maximum energy possible such that no sample degradation occurs during collection.
	<ol>
		<li>Collect the spectra by accumulating between 10 and 50 scans and using an exposure time between 2 and 5 s for each individual scan to achieve a reasonable signal-to-noise ratio.</li>
	</ol>
	</li>
</ol>
5. Film Morphology &#8211; Scanning Electron Microscopy (SEM)
<ol>
	<li>For the SEM analysis of functionalized versus unfunctionalized CNT/GNPs, dilute a droplet of each dispersion to 0.1 g/L using deionized water. Deposit it onto an aluminum SEM stub and allow to dry in air overnight.</li>
	<li>For EPD films deposited onto the stainless-steel electrodes, cut the electrodes into 1 cm x 1 cm squares and mount them onto sample stubs using double-sided conductive tape. Paint a small line of silver dag (i.e., conductive adhesive/paint) from the sample stub onto the top surface of the specimen to improve the conductive path. Dry the sample under a heater lamp for at least 15 min.</li>
	<li>Place the mounted specimen in the sputter coater and give it a conductive iridium coating approximately 1.3-1.5 nm thick19.
	<ol>
		<li>On the thickness measurement unit, set the material density to the appropriate level, which is 22.56 g/cm3 for iridium. Adjust the target thickness setting to 1.0 nm to give a thickness of approximately 1.3-1.5 nm when accounting for thermal drift during the coating process.</li>
		<li>Set the coater unit to allow the sputter coater operation to be controlled by the thickness measurement unit. Select the desired power output, which should be 80 mA for a high-resolution coating19.</li>
		<li>Zero the coating thickness gauge on the thickness control unit and press the &#34;Cycle&#34; button to commence the automated chamber evacuation, argon bleed/flush and coating sequence. When the power has reached the desired level, move aside the target shield to allow the coating to commence. Rotate and tilt the stage during the coating to facilitate an even coating on all sides.</li>
	</ol>
	</li>
	<li>Examine the nanomaterials using a field-emission SEM with an in-lens detector. Use a working distance of approximately 3 mm and an accelerating voltage of 3.0 kV.</li>
</ol>

<ol><li>Pandey, G., Thostenson, E. T. <a target="_blank" href="http://www.tandfonline.com/doi/abs/10.1080/15583724.2012.703747">Carbon Nanotube-Based Multifunctional Polymer Nanocomposites.</a> Polym. Rev. 52 (3), 355-416 (2012).</li>
<li>Das, T. K., Prusty, S. <a target="_blank" href="http://www.tandfonline.com/doi/abs/10.1080/03602559.2012.751410?journalCode=lpte20">Graphene-Based Polymer Composites and Their Applications.</a> Polym.-Plast. Technol. 52 (4), 319-331 (2013).</li>
<li>Karger-Kocsis, J., Mahmood, H., Pegoretti, A. <a target="_blank" href="http://www.sciencedirect.com/science/article/pii/S0079642515000328">Recent advances in fiber/matrix interphase engineering for polymer composites.</a> Prog. Mater. Sci. 73, 1-43 (2015).</li>
<li>Qian, H., Greenhalgh, E. S., Shaffer, M. S. P., Bismarck, A. <a target="_blank" href="http://pubs.rsc.org/en/content/articlelanding/2010/jm/c000041h#!divAbstract">Carbon nanotube-based hierarchical composites: a review.</a> J. Mater. Chem. 20 (23), 4751-4762 (2010).</li>
<li>Hummers, W. S., Offeman, R. E. <a target="_blank" href="http://pubs.acs.org/doi/abs/10.1021/ja01539a017">Preparation of graphitic oxide.</a> J. Am. Chem. Soc. 80, 1339-1339 (1958).</li>
<li>Shaffer, M. S. P., Fan, X., Windle, A. H. <a target="_blank" href="http://www.sciencedirect.com/science/article/pii/S0008622398001304">Dispersion and Packing of Carbon Nanotubes.</a> Carbon. 36 (11), 1603-1612 (1998).</li>
<li>Hamon, M. A., et al. <a target="_blank" href="http://onlinelibrary.wiley.com/doi/10.1002/(SICI)1521-4095(199907)11:10%3C834::AID-ADMA834%3E3.0.CO;2-R/abstract">Dissolution of Single-Walled Carbon Nanotubes.</a> Adv. Mater. 11, 834-840 (1999).</li>
<li>Low, C. T. J., et al. <a target="_blank" href="http://www.sciencedirect.com/science/article/pii/S0008622312009219">Electrochemical approaches to the production of graphene flakes and their potential applications.</a> Carbon. 54, 1-21 (2013).</li>
<li>Rider, A. N., et al. <a target="_blank" href="http://www.sciencedirect.com/science/article/pii/S0008622315300993">Hierarchical composites with high-volume fractions of carbon nanotubes: Influence of plasma surface treatment and thermoplastic nanophase-modified epoxy.</a> Carbon. 94, 971-981 (2015).</li>
<li>Tchoul, M. N., Ford, W. T., Lolli, G., Resasco, D. E., Arepalli, S. <a target="_blank" href="http://pubs.acs.org/doi/abs/10.1021/cm071758l">Effect of Mild Nitric Acid Oxidation on Dispersability, Size, and Structure of Single-Walled Carbon Nanotubes.</a> Chem. Mater. 19, 5765-5772 (2007).</li>
<li>Gong, X., Liu, J., Baskaran, S., Voise, R. D., Young, J. S. <a target="_blank" href="http://pubs.acs.org/doi/abs/10.1021/cm9906396">Surfactant-Assisted Processing of Carbon Nanotube/Polymer Composites.</a> Chem. Mater. 12, 1049-1052 (2000).</li>
<li>An, Q., Rider, A. N., Thostenson, E. T. <a target="_blank" href="http://www.sciencedirect.com/science/article/pii/S0008622312004022">Electrophoretic deposition of carbon nanotubes onto carbon-fiber fabric for production of carbon/epoxy composites with improved mechanical properties.</a> Carbon. 50 (11), 4130-4143 (2012).</li>
<li>An, Q., Rider, A. N., Thostenson, E. T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Heirarchical+composite+structures+prepared+by+electrophoretic+deposition+of+carbon+nanotubes+onto+glass+fibers%5BTitle%5D)+AND+%22ACS+Appl.+Mater.+Interfac%22%5BJournal%5D)">Heirarchical composite structures prepared by electrophoretic deposition of carbon nanotubes onto glass fibers.</a> ACS Appl. Mater. Interfac. 5 (6), 2022-2032 (2013).</li>
<li>Rider, A. N., An, Q., Thostenson, E. T., Brack, N. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Ultrasonicated-ozone+modification+of+exfoliated+graphite+for+stable+aqueous+graphitic+nanoplatelet+dispersions%5BTitle%5D)+AND+%22Nanotechnology%22%5BJournal%5D)">Ultrasonicated-ozone modification of exfoliated graphite for stable aqueous graphitic nanoplatelet dispersions.</a> Nanotechnology. 25 (49), 495607(2014).</li>
<li>Fairley, N. <a target="_blank" href="http://scholar.google.com/scholar?hl=en&safe=off&q=author%3aFairley%2C+N+%22CasaXPS+Manual+2.3.15+Introduction+to+XPS+and+AES%2C+Rev.+1.2%22">CasaXPS Manual 2.3.15 Introduction to XPS and AES, Rev. 1.2</a>. , Casa Software Ltd. www.casaxps.com (2009).</li>
<li>Kratos elemental library for use with Casa XPS software. , Available from: 
 <a target="_blank" href="http://www.casaxps.com/kratos">http://www.casaxps.com/kratos</a> (2016).</li>
<li>Leiro, J., Heinonen, M., Laiho, T., Batirev, I. <a target="_blank" href="http://www.sciencedirect.com/science/article/pii/S0368204802002840">Core-level XPS spectra of fullerene, highly oriented pyrolitic graphite, and glassy carbon.</a> J. Electron Spectrosc. 128, 205-213 (2003).</li>
<li><a target="_blank" href="http://scholar.google.com/scholar?hl=en&safe=off&q=%22DXR+Raman+Instruments%3A+Getting+Started%22">DXR Raman Instruments: Getting Started</a>. , Thermo Fisher Scientific. 269-215100 Rev. A (2008).</li>
<li><a target="_blank" href="http://scholar.google.com/scholar?hl=en&safe=off&q=%22Cressington+208HR+High+Resolution+Sputter+Coater+for+FE-SEM%3A+Operating+Manual%22">Cressington 208HR High Resolution Sputter Coater for FE-SEM: Operating Manual</a>. , Cressington Scientific Instruments Ltd. Watford, UK. Rev. 5 (2003).</li>
<li>Krishnamoorthy, K., Veerapandian, M., Yun, K., Kim, S. -J. <a target="_blank" href="http://www.sciencedirect.com/science/article/pii/S0008622312008263">The chemical and structural analysis of graphene oxide with different degrees of oxidation.</a> Carbon. 53, 38-49 (2013).</li>
<li>Hamaker, H. C. <a target="_blank" href="http://pubs.rsc.org/en/Content/ArticleLanding/1940/TF/TF9403500279#!divAbstract">Formation of a Deposit by Electrophoresis.</a> T. Faraday Soc. 35, 279-287 (1940).</li>
<li>Rider, A. N., An, Q., Brack, N., Thostenson, E. T. <a target="_blank" href="http://www.sciencedirect.com/science/article/pii/S1385894715001308">Polymer nanocomposite - fiber model interphases: Influence of processing and interface chemistry on mechanical performance.</a> Chem. Eng. J. 269, 121-134 (2015).</li>
</ol>

The authors have nothing to disclose.

When working with nanoparticles of high hardness, such as CNTs, the potential erosion effect on containers and tubing should not be overlooked. Step 1.14 in the protocol was inserted after the tubing became worn at a bend due to CNTs impinging on the tube side wall, causing a system leak.
Also, note that the CNTs are in suspension, not solution, and that they must be stirred before each use if a homogeneous suspension is desired. For example, this would be necessary to maintain the desired con...

The use of carbon nanomaterials to modify polymeric and composite systems has seen intensive research interest over the past 20 years. Recent reviews on both the use of carbon nanotubes1 (CNTs) and graphene nanoplatelets2 (GNPs) provide an indication of the breadth of research. The high specific stiffness and strength of CNTs and GNPs, as well as their high intrinsic electrical conductivity, make the materials ideally suited for incorporation into polymeric systems to enhance both the mechanical and electrical performance of the nanocomposite materials. CNTs and GNPs have also been used for the development of hierarchical composite structures by using the carbon nanomaterials to modify both fiber interfacial adhesion and matrix stiffness3,4.
The homogeneous dispersion of carbon nanomaterials into polymeric systems often requires processing steps, which chemically alter the nanomaterials to improve the chemical compatibility with the polymer matrix, remove impurities, and reduce or remove agglomerates from the as-received materials. A variety of methods to chemically modify carbon nanomaterials are available and may include wet chemical oxidation using strong acids5,6, modification with surfactants7, electrochemical intercalation and exfoliation8, or dry chemical processing using plasma-based processes9.
The use of strong acids in the oxidation step of CNTs introduces oxygen functional groups and removes impurities. However, it has the disadvantage of significantly reducing the CNT length, introducing damage to the CNT outer walls and using dangerous chemicals, which need to be isolated from the treated material for further processing10. The use of surfactants combined with ultrasonication offers a less aggressive method to prepare stable dispersions, but the surfactant is often difficult to remove from the treated material and may not be compatible with the polymer being used to prepare the nanocomposite materials1,11. The strength of the chemical interaction between the surfactant molecule and CNT or GNP may also be insufficient for mechanical applications. Dry plasma treatment processes conducted under atmospheric conditions may be suitable for functionalizing arrays of CNTs, present on fiber or planar surfaces, used to prepare hierarchical composites9. However, the atmospheric plasma is more difficult to apply to dry powders and does not address the problems with agglomerates present in as-manufactured raw carbon nanomaterials.
In the present work, we introduce a detailed description of the ultrasonicated-ozonolysis (USO) method that we have previously applied to carbon nanomaterials12,13,14. The USO process is used to prepare stable, aqueous dispersions that are suitable for electrophoretically depositing (EPD) both CNTs and GNPs onto carbon and glass fibers. Examples of EPD using USO-functionalized CNTs to deposit thin, uniform films onto stainless steel and carbon fabric substrates will be provided. Methods and typical results used to chemically characterize the functionalized CNTs and GNPs will also be provided, using both X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy. A brief discussion of the characterization results in comparison with other functionalization techniques will be provided.
Work Health and Safety Notice
The effects of exposure to nanoparticles such as CNTs, on human health are not well understood. It is recommended that special measures be taken to minimize exposure to and avoid environmental contamination with CNT powders. Suggested hazard isolation measures include working within a HEPA filter-equipped fume cupboard and/or glove box. Occupational hygiene measures include wearing protective clothing and two layers of gloves and performing regular cleaning of surfaces using damp paper towels or a vacuum cleaner with a HEPA filter to remove stray CNT powders. Contaminated articles should be bagged for hazardous waste disposal.
Exposure to ozone can irritate the eyes, lungs, and respiratory system, and at higher concentrations may cause lung damage. It is recommended that measures be taken to minimize personal and environmental exposure to generated ozone gas. Isolation measures include working within a fume cupboard. As the return air stream will contain unused ozone, it should be passed through an ozone destruct unit before being releasing into the atmosphere. Dispersions that have had ozone bubbled through them will contain some dissolved ozone. After ozonolysis operations, allow the dispersions to sit for 1 h before undertaking further processing so that the ozone can undergo natural decomposition.

<table><tbody><tr><td>Ultrasonic bath</td><td>Soniclean</td><td>80TD</td><td></td></tr><tr><td>Ultrasonic horn</td><td>Misonix</td><td>S-4000-010 with CL5 converter</td><td>Daintree Scientific</td></tr><tr><td>Flocell stainless steel water jacketed</td><td>Misonix</td><td>800BWJ</td><td>Daintree Scientific</td></tr><tr><td>Peristaltic pump</td><td>Masterflex easy-load</td><td>7518-00</td><td></td></tr><tr><td>Controller for peristaltic pump</td><td>Masterflex modular controller</td><td>7553-78</td><td></td></tr><tr><td>Ozone generator</td><td>Ozone Solutions</td><td>TG-20</td><td></td></tr><tr><td>Ozone destruct unit</td><td>Ozone Solutions</td><td>ODS-1</td><td></td></tr><tr><td>Recirculating liquid cooler</td><td>Thermoline</td><td>TRC2-571-T</td><td></td></tr><tr><td>Multi-mode power supply unit</td><td>TTi</td><td>EX752M</td><td></td></tr><tr><td>High resolution computing multimeter</td><td>TTi</td><td>1906</td><td></td></tr><tr><td>X-ray photoelectron spectroscopy</td><td>Kratos Analytical</td><td>Axis Nova</td><td></td></tr><tr><td>XPS analysis software</td><td>Casa Software</td><td>Casa XPS</td><td>www.casaxps.com</td></tr><tr><td>Kratos elemental library for use with Casa XPS</td><td>Casa Software</td><td>Download Kratos Related Files</td><td>http://www.casaxps.com/kratos/</td></tr><tr><td>Raman dispersive confocal microscope</td><td>Thermo</td><td>DXR</td><td></td></tr><tr><td>Field emission scanning electron microscope</td><td>Leo</td><td>1530 VP</td><td></td></tr><tr><td>Sputter coater with iridium target</td><td>Cressington</td><td>208 HR</td><td></td></tr><tr><td>Thickness measurement unit</td><td>Cressington</td><td>mtm 20</td><td></td></tr><tr><td>Magnetic stirrer</td><td>Stuart</td><td>CD162</td><td></td></tr><tr><td>Analytical balance</td><td>Kern</td><td>ALS 220-4N</td><td></td></tr><tr><td>Analytical balance</td><td>Mettler Toledo</td><td>NewClassic MF MS 2045</td><td></td></tr><tr><td>Laboratory balance</td><td>Shimadzu</td><td>ELB 3000</td><td></td></tr><tr><td>Electrodes from 316 stainless steel sheet</td><td>RS Components</td><td>559-199</td><td></td></tr><tr><td>Sanding sheets, P1000 grade</td><td>Norton</td><td>No-Fil A275</td><td></td></tr><tr><td>Multi-walled carbon nanotubes</td><td>Hanwha</td><td>CM-95</td><td>http://hcc.hanwha.co.kr/eng/business/bus_table/nano_02.jsp</td></tr><tr><td>Graphene nanoplatelets</td><td>XG Sciences</td><td>XGNP Grade C</td><td>http://xgsciences.com/products/graphene-nanoplatelets/grade-c/</td></tr></tbody></table>

functionalization and dispersion of carbon nanomaterials using an environmentally friendly ultrasonicated ozonolysis process

Functionalization of carbon nanomaterials is often a critical step that facilitates their integration into larger material systems and devices. In the as-received form, carbon nanomaterials, such as carbon nanotubes (CNTs) or graphene nanoplatelets (GNPs), may contain large agglomerates. Both agglomerates and impurities will diminish the benefits of the unique electrical and mechanical properties offered when CNTs or GNPs are incorporated into polymers or composite material systems. Whilst a variety of methods exist to functionalize carbon nanomaterials and to create stable dispersions, many the processes use harsh chemicals, organic solvents, or surfactants, which are environmentally unfriendly and may increase the processing burden when isolating the nanomaterials for subsequent use. The current research details the use of an alternative, environmentally friendly technique for functionalizing CNTs and GNPs. It produces stable, aqueous dispersions free of harmful chemicals. Both CNTs and GNPs can be added to water at concentrations up to 5 g/L and can be recirculated through a high-powered ultrasonic cell. The simultaneous injection of ozone into the cell progressively oxidizes the carbon nanomaterials, and the combined ultrasonication breaks down agglomerates and immediately exposes fresh material for functionalization. The prepared dispersions are ideally suited for the deposition of thin films onto solid substrates using electrophoretic deposition (EPD). CNTs and GNPs from the aqueous dispersions can be readily used to coat carbon- and glass-reinforcing fibers using EPD for the preparation of hierarchical composite materials.

Figure 3 shows the XPS wide-scan characterization of CNTs that had undergone USO treatment. CNTs that had not undergone USO show almost no oxygen content. As the USO time increases, the surface oxygen level increases. Figure 4 charts the oxygen-to-carbon ratio increases as a function of USO time. Table 1 shows the deconvoluted carbon species atomic concentrations of GNP treated with USO. The peak fitting used a combination of constrained ...

Watch this Scientific Journal Video about Functionalization and Dispersion of Carbon Nanomaterials Using an Environmentally Friendly Ultrasonicated Ozonolysis Process at JoVE.com

Functionalization and Dispersion of Carbon Nanomaterials Using an Environmentally Friendly Ultrasonicated Ozonolysis Process

Here, a novel method for the functionalization and stable dispersion of carbon nanomaterials in aqueous environments is described. Ozone is injected directly into an aqueous dispersion of carbon nanomaterial that is continuously recirculated through a high-powered ultrasonic cell.

Functionalization of carbon nanomaterials is often a critical step that facilitates their integration into larger material systems and devices. In the ...

functionalization-dispersion-carbon-nanomaterials-using-an

Research

JoVE Journal

Environment

10.2K Views.  Defence Science and Technology Group.  Hier wordt een nieuwe methode voor de functionalisatie en stabiele dispersie van koolstofnanomaterialen in waterige omgevingen beschreven. Ozon wordt direct ingespoten in een waterige dispersie van koolstof nanomateriaal, dat continu door een ultrasone cel met hoog vermogen wordt gerecirculeerd. 

Video: Functionalization and Dispersion of Carbon Nanomaterials Using an Environmentally Friendly Ultrasonicated Ozonolysis Process

Dry Oxidation and Vacuum Annealing Treatments for Tuning the Wetting Properties of Carbon Nanotube Arrays

In this article, we describe a simple method to reversibly tune the wetting properties of vertically aligned carbon nanotube (CNT) arrays. Here, CNT arrays are defined as densely packed multi-walled carbon nanotubes oriented perpendicular to the growth substrate as a result of a growth process by the standard thermal chemical vapor deposition (CVD) technique.1,2 These CNT arrays are then exposed to vacuum annealing treatment to make them more hydrophobic or to dry oxidation treatment to render them more hydrophilic. The hydrophobic CNT arrays can be turned hydrophilic by exposing them to dry oxidation treatment, while the hydrophilic CNT arrays can be turned hydrophobic by exposing them to vacuum annealing treatment. Using a combination of both treatments, CNT arrays can be repeatedly switched between hydrophilic and hydrophobic.2 Therefore, such combination show a very high potential in many industrial and consumer applications, including drug delivery system and high power density supercapacitors.3-5
The key to vary the wettability of CNT arrays is to control the surface concentration of oxygen adsorbates. Basically oxygen adsorbates can be introduced by exposing the CNT arrays to any oxidation treatment. Here we use dry oxidation treatments, such as oxygen plasma and UV/ozone, to functionalize the surface of CNT with oxygenated functional groups. These oxygenated functional groups allow hydrogen bond between the surface of CNT and water molecules to form, rendering the CNT hydrophilic. To turn them hydrophobic, adsorbed oxygen must be removed from the surface of CNT. Here we employ vacuum annealing treatment to induce oxygen desorption process. CNT arrays with extremely low surface concentration of oxygen adsorbates exhibit a superhydrophobic behavior.

This article describes a simple method to fabricate vertically aligned carbon nanotube arrays by CVD and to subsequently tune their wetting properties by exposing them to vacuum annealing or dry oxidation treatment.

In this article, we describe a simple method to reversibly  tune the wetting properties of vertically aligned carbon nanotube (CNT) arrays.  Here, CNT ...

Engineering

Synthesis and Functionalization of Nitrogen-doped Carbon Nanotube Cups with Gold Nanoparticles as Cork Stoppers

Nitrogen-doped carbon nanotubes consist of many cup-shaped graphitic compartments termed as nitrogen-doped carbon nanotube cups (NCNCs). These as-synthesized graphitic nanocups from chemical vapor deposition (CVD) method were stacked in a head-to-tail fashion held only through noncovalent interactions. Individual NCNCs can be isolated out of their stacking structure through a series of chemical and physical separation processes. First, as-synthesized NCNCs were oxidized in a mixture of strong acids to introduce oxygen-containing defects on the graphitic walls. The oxidized NCNCs were then processed using high-intensity probe-tip sonication which effectively separated the stacked NCNCs into individual graphitic nanocups. Owing to their abundant oxygen and nitrogen surface functionalities, the resulted individual NCNCs are highly hydrophilic and can be effectively functionalized with gold nanoparticles (GNPs), which preferentially fit in the opening of the cups as cork stoppers. These graphitic nanocups corked with GNPs may find promising applications as nanoscale containers and drug carriers.

We discussed the synthesis of individual graphitic nanocups using a series of techniques including chemical vapor deposition, acid oxidation and probe-tip sonication. By citrate reduction of HAuCl4, the graphitic nanocups were effectively corked with gold nanoparticles due to the chemically reactive edges of the cups.

Nitrogen-doped carbon  nanotubes consist of many cup-shaped graphitic compartments termed as  nitrogen-doped carbon nanotube cups (NCNCs).  These ...

Preparation of Silica Nanoparticles Through Microwave-assisted Acid-catalysis

Microwave-assisted synthetic techniques were used to quickly and reproducibly produce silica nanoparticle sols using an acid catalyst with nanoparticle diameters ranging from 30-250 nm by varying the reaction conditions. Through the selection of a microwave compatible solvent, silicic acid precursor, catalyst, and microwave irradiation time, these microwave-assisted methods were capable of overcoming the previously reported shortcomings associated with synthesis of silica nanoparticles using microwave reactors. The siloxane precursor was hydrolyzed using the acid catalyst, HCl. Acetone, a low-tan &#948; solvent, mediates the condensation reactions and has minimal interaction with the electromagnetic field. Condensation reactions begin when the silicic acid precursor couples with the microwave radiation, leading to silica nanoparticle sol formation. The silica nanoparticles were characterized by dynamic light scattering data and scanning electron microscopy, which show the materials&#39; morphology and size to be dependent on the reaction conditions. Microwave-assisted reactions produce silica nanoparticles with roughened textured surfaces that are atypical for silica sols produced by St&#246;ber&#39;s methods, which have smooth surfaces.

Silica nanoparticles were prepared using acid-catalysis of a siloxane precursor and microwave-assisted synthetic techniques resulting in the controlled growth of nanomaterials ranging from 30-250 nm in diameter. The growth dynamics can be controlled by varying the initial silicic acid concentration, time of the reaction, and temperature of reaction.

Microwave-assisted synthetic techniques were used to quickly and reproducibly produce silica nanoparticle sols using an acid catalyst with nanoparticle ...

Chemistry

Transport of Surface-modified Carbon Nanotubes through a Soil Column

Carbon nanotubes (CNTs) are widely manufactured nanoparticles, which are being utilized in a number of consumer products, such as sporting goods, electronics and biomedical applications. Due to their accelerating production and use, CNTs constitute a potential environmental risk if they are released to soil and groundwater systems. It is therefore essential to improve the current understanding of environmental fate and transport of CNTs. The transport and retention of CNTs in both natural and artificial media have been reported in literature, but the findings widely vary and are thus not conclusive. There are a number of physical and chemical parameters responsible for variation in retention and transport. In this study, a complete procedure of selected multiwalled carbon nanotubes (MWCNTs) is presented starting from their surface modification to a complete set of laboratory column experiments at critical physical and chemical scenarios. Results indicate that the stability of the commercially available MWCNTs are critical with their attached surface functional group which can also influence the transport and retention of MWCNT through the surrounding medium.

Surface properties of a nanoparticle are important for their interaction with the surrounding medium. Therefore the surface modification of carbon nanotubes can be critical for their transport and retention through porous media. Here, lab scale column experiments are used to understand the possible transport and retention of these nanoparticles.

Carbon nanotubes (CNTs) are widely manufactured nanoparticles, which are being utilized in a number of consumer products, such as sporting goods, ...

Dispersion of Nanomaterials in Aqueous Media: Towards Protocol Optimization

The sonication process is commonly used for de-agglomerating and dispersing nanomaterials in aqueous based media, necessary to improve homogeneity and stability of the suspension. In this study, a systematic step-wise approach is carried out to identify optimal sonication conditions in order to achieve a stable dispersion. This approach has been adopted and shown to be suitable for several nanomaterials (cerium oxide, zinc oxide, and carbon nanotubes) dispersed in deionized (DI) water. However, with any change in either the nanomaterial type or dispersing medium, there needs to be optimization of the basic protocol by adjusting various factors such as sonication time, power, and sonicator type as well as temperature rise during the process. The approach records the dispersion process in detail. This is necessary to identify the time points as well as other above-mentioned conditions during the sonication process in which there may be undesirable changes, such as damage to the particle surface thus affecting surface properties. Our goal is to offer a harmonized approach that can control the quality of the final, produced dispersion. Such a guideline is instrumental in ensuring dispersion quality repeatability in the nanoscience community, particularly in the field of nanotoxicology.

Here, we present a step-wise protocol for the dispersion of nanomaterials in aqueous media with real-time characterization to identify the optimal sonication conditions, intensity, and duration for improved stability and uniformity of nanoparticle dispersions without impacting the sample integrity.

The sonication process is commonly used for de-agglomerating and dispersing nanomaterials in aqueous based media, necessary to improve homogeneity and ...

Functionalization of Single-walled Carbon Nanotubes with Thermo-reversible Block Copolymers and Characterization by Small-angle Neutron Scattering

We demonstrate a protocol for single-walled carbon nanotube functionalization using thermo-sensitive PEO-PPO-PEO triblock copolymers in an aqueous solution. In a carbon nanotube/PEO105-PPO70-PEO105 (poloxamer 407) aqueous solution, the amphiphilic poloxamer 407 adsorbs onto the carbon nanotube surfaces and self-assembles into continuous layers, driven by intermolecular interactions between constituent molecules. The addition of 5-methylsalicylic acid changes the self-assembled structure from spherical-micellar to a cylindrical morphology. The fabricated poloxamer 407/carbon nanotube hybrid particles exhibit thermo-responsive structural features so that the density and thickness of poloxamer 407 layers are also reversibly controllable by varying temperature. The detailed structural properties of the poloxamer 407/carbon nanotube particles in suspension can be characterized by small-angle neutron scattering experiments and model fit analyses. The distinct curve shapes of the scattering intensities depending on temperature control or addition of aromatic additives are well described by a modified core-shell cylinder model consisting of a carbon nanotube core cylinder, a hydrophobic shell, and a hydrated polymer layer. This method can provide a simple but efficient way for the fabrication and in-situ characterization of carbon nanotube-based nano particles with a structure-tunable encapsulation.

A method for the functionalization of carbon nanotubes with structure-tunable polymeric encapsulation layers and structural characterization using small-angle neutron scattering is presented.

We demonstrate a protocol for single-walled carbon nanotube functionalization using thermo-sensitive PEO-PPO-PEO triblock copolymers in an aqueous ...

Protocol of Electrochemical Test and Characterization of Aprotic Li-O2 Battery

We demonstrate a method for electrochemical testing of an aprotic Li-O2 battery. An aprotic Li-O2 battery is made of a Li-metal anode, an aprotic electrolyte, and an O2-breathing cathode. The aprotic electrolyte is a solution of lithium salt with aprotic solvent; and porous carbon is commonly used as the cathode substrate. To improve the performance, an electrocatalyst is deposited onto the porous carbon substrate by certain deposition methods, such as atomic layer deposition (ALD) and wet-chemistry reaction. The as-prepared cathode materials are characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray absorption near edge structure (XANES). A Swagelok-type cell, sealed in a glass chamber filled with pure O2, is used for the electrochemical test on a battery test system. The cells are tested under either capacity-controlled mode or voltage controlled mode. The reaction products are investigated by electron microscopy, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy, and Raman spectroscopy to study the possible pathway of oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). This protocol demonstrates a systematic and efficient arrangement of routine tests of the aprotic Li-O2 battery, including the electrochemical test and characterization of battery materials.

Protocol of Electrochemical Test and Characterization of Aprotic Li-O2 Battery

A protocol for the electrochemical testing of an aprotic Li-O2 battery with the preparation of electrodes and electrolytes and an introduction of the frequently used methods of characterization is presented here.

We demonstrate a method for electrochemical testing of an aprotic Li-O2 battery. An aprotic Li-O2 battery is made of a Li-metal anode, an aprotic ...

Preparation of Biomass-based Mesoporous Carbon with Higher Nitrogen-/Oxygen-chelating Adsorption for Cu(II) Through Microwave Pre-Pyrolysis

An environment-friendly technique for synthesizing biomass-based mesoporous activated carbon with high nitrogen-/oxygen-chelating adsorption for Cu(II) is proposed. Bagasse impregnated with phosphoric acid is utilized as the precursor. To pyrolyze the precursor, two separate heating modes are used: microwave pyrolysis and conventional electric-heating pyrolysis. The resulting bagasse-derived carbon samples are modified with nitrification and reduction modification. Nitrogen (N)/oxygen (O) functional groups are simultaneously introduced to the surface of activated carbon, enhancing its adsorption of Cu(II) by complexing and ion-exchange. Characterization and copper adsorption experiments are performed to investigate the physicochemical properties of four prepared carbon samples and determine which heating method favors the subsequent modification for doping of N/O functional groups. In this technique, based on analyzing data of nitrogen adsorption, Fourier transform infrared spectroscopy, and batch adsorption experiments, it is proven that microwave-pyrolyzed carbon has more defect sites and, therefore, time-saving effective microwave pyrolysis contributes more N/O species to the carbon, although it leads to a lower specific surface area. This technique offers a promising route to synthesis adsorbents with higher nitrogen and oxygen content and a higher adsorption capacity of heavy-metal ions in wastewater remediation applications.

Preparation of Biomass-based Mesoporous Carbon with Higher Nitrogen-/Oxygen-chelating Adsorption for CuII Through Microwave Pre-Pyrolysis

Here, we present a protocol to synthesize nitrogen/oxygen dual-doped mesoporous carbon from biomass by chemical activation in different pyrolysis modes followed by modification. We demonstrate that the microwave pyrolysis benefits the subsequent modification process to simultaneously introduce more nitrogen and oxygen functional groups on the carbon.

An environment-friendly technique for synthesizing biomass-based mesoporous activated carbon with high nitrogen-/oxygen-chelating adsorption for Cu(II) is ...

Grafting Multiwalled Carbon Nanotubes with Polystyrene to Enable Self-Assembly and Anisotropic Patchiness

We demonstrate a straightforward protocol to graft pristine multiwalled carbon nanotubes (MWCNTs) with polystyrene (PS) chains at the sidewalls through a free-radical polymerization strategy to enable the modulation of the nanotube surface properties and produce supramolecular self-assembly of the nanostructures. First, a selective hydroxylation of the pristine nanotubes through a biphasic catalytically mediated oxidation reaction creates superficially distributed reactive sites at the sidewalls. The latter reactive sites are subsequently modified with methacrylic moieties using a silylated methacrylic precursor to create polymerizable sites. Those polymerizable groups can address further polymerization of styrene to produce a hybrid nanomaterial containing PS chains grafted to the nanotube sidewalls. The polymer-graft content, amount of silylated methacrylic moieties introduced and hydroxylation modification of the nanotubes are identified and quantified by Thermogravimetric Analysis (TGA). The presence of reactive functional groups hydroxyl and silylated methacrylate are confirmed by Fourier Transform Infrared Spectroscopy (FT-IR). Polystyrene-grafted carbon nanotube solutions in tetrahydrofuran (THF) provide wall-to-wall collinearly self-assembled nanotubes when cast samples are analyzed by transmission electron microscopy (TEM). Those self-assemblies are not obtained when suitable blanks are similarly cast from analogous solutions containing non-grafted counterparts. Therefore, this method enables the modification of the nanotube anisotropic patchiness at the sidewalls which results into spontaneous auto-organization at the nanoscale.

A procedure for the synthesis of polystyrene-grafted multiwalled carbon nanotubes using successive chemical modification steps to selectively introduce the polymer chains to the sidewalls and their self-assembly via anisotropic patchiness is presented.

We demonstrate a straightforward protocol to graft pristine multiwalled carbon nanotubes (MWCNTs) with polystyrene (PS) chains at the sidewalls through a ...

Tuning the Acidity of Pt/ CNTs Catalysts for Hydrodeoxygenation of Diphenyl Ether

We herein present a method for the synthesis of HNbWO6, HNbMoO6, HTaWO6 solid acid nanosheet modified Pt/CNTs. By varying the weight of various solid acid nanosheets, a series of Pt/xHMNO6/CNTs with different solid acid compositions (x = 5, 20 wt%; M = Nb, Ta; N = Mo, W) have been prepared by carbon nanotube pretreatment, protonic exchange, solid acid exfoliation, aggregation and finally Pt particles impregnation. The Pt/xHMNO6/CNTs are characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy and NH3-temperature programmed desorption. The study revealed that HNbWO6 nanosheets were attached on CNTs, with some edges of the nanosheets being bent in shape. The acid strength of the supported Pt catalysts increases in the following order: Pt/CNTs &#60; Pt/5HNbWO6/CNTs &#60; Pt/20HNbMoO6/CNTs &#60; Pt/20HNbWO6/CNTs &#60; Pt/20HTaWO6/CNTs. In addition, the catalytic hydroconversion of lignin-derived model compound: diphenyl ether using the synthesized Pt/20HNbWO6 catalyst has been investigated.

A protocol for the synthesis of HNbWO6, HNbMoO6, HTaWO6 solid acid nanosheet modified Pt/CNTs is presented.

We herein present a method for the synthesis of HNbWO6, HNbMoO6, HTaWO6 solid acid nanosheet modified Pt/CNTs. By varying the weight of various solid acid ...

Functionalization and Dispersion of Carbon Nanomaterials Using an Environmentally Friendly Ultrasonicated Ozonolysis Process

Samenvatting

Meer video's verkennen