We thank Dr. Rob Sladek for the use of the inkjet spotter. We acknowledge the final support from the Canadian Institutes for Health Research (CIHR), the Natural Science and Engineering Research Council of Canada (NSERC), the Canadian Cancers Society Research Institute and the Canada Foundation for Innovation (CFI). D.J. thanks support from a Canada Research Chair.

1. Fabrication and storage of snap chips
<ol>
	<li>Single transfer method (Figure 1a)
	<ol>
		<li>Spot cAb solutions containing 400 &#181;g/mL antibodies and 20% glycerol in phosphate-buffered saline (PBS) onto a nitrocellulose (or a functionalized glass) assay slide with an inkjet microarray spotter13 at a relative humidity of 60% (1.2 nL for each spot) with 800 &#181;m center-to-center spacing. Make sure the slide is fixed on the spotter deck according to one corner (here, the bottom left corner was used).</li>
		<li>Incubate the spotted assay slide at room temperature for 1 h with a relative humidity of 60%.</li>
		<li>Clamp a slide module gasket with 16 compartments on the assay slide to divide it into 16 wells. Rinse the slide three times by adding 80 &#181;L of PBS containing 0.1% Tween-20 (PBST) into each well, and shaking at 450 rpm on a shaker, 5 min each time.</li>
		<li>Add 80 &#181;L of blocking solutions to each well and shake for 1 h at 450 rpm.</li>
		<li>Remove the gasket and dry the assay slide with a stream of nitrogen.</li>
		<li>Fix a transfer slide on the spotter deck and push the bottom left corner of the slide against bottom left corner of the spotter deck. Inkjet spot an array of alignment marks (a solution of polystyrene micro-beads) with the same layout as that for the cAbs.</li>
		<li>Let the alignment marks dry. Flip the transfer slide and put it back onto the spotter deck, fixing against the bottom left corner.</li>
		<li>Prepare the dAb spotting solutions containing 20 &#181;g/mL antibodies, 20% glycerol, and 1% BSA.</li>
		<li>Using the spotter&#39;s camera, take a picture of an alignment mark. Implement this picture into the spotting program as a fiducial and get the image recognition system of the inkjet spotter to identify the most top left mark. Use its coordinate as the first spot of the dAb array. Spot 8 nL per droplet with a center-to-center spacing of 800 &#181;m.</li>
	</ol>
	</li>
	<li>Double transfer method (Figure 1b)
	<ol>
		<li>Place a transfer slide 1 on the inkjet spotter deck against the bottom left corner. Spot cAbs solutions containing 400 &#181;g/mL antibodies, 20% glycerol, and 1% BSA in PBS onto the slide with an inkjet microarray spotter at a relative humidity of 60% (0.4 nL for each spot and ~ 200 &#181;m in diameter). The center-to-center spacing is 400 &#181;m.</li>
		<li>Snap the transfer slide with a nitrocellulose coated (or a functionalized glass) assay slide using a snap apparatus (Figure 2) to transfer the cAb droplets onto the assay slide.
		<ol>
			<li>Turn all six buttons on the side of the snap apparatus by 90 degrees to pull and lock all the plungers in the open position. Insert the transfer slide into the slide holder in its receptacle with the clipped corner facing the fixed pogo pin. Turn the first set of three buttons to release the plungers with the golden pogo pin and make sure the slides are pushed against the alignment pins.</li>
			<li>Insert a nitrocellulose-coated slide in the snap apparatus upside-down sitting on the 4 pogo pins. Turn the second set of three buttons to release plungers with the silver pin and make sure the slides are pushed against the alignment pins.</li>
			<li>Close the snap apparatus by placing the top shell on the slide holder using the alignment pillars and holes for a precise positioning.</li>
			<li>Insert the closed snap apparatus into its cage and push the closure tab completely down to bring the microarrays face-to-face while applying the appropriate pressure. Keep closed for 1 min.</li>
		</ol>
		</li>
		<li>Separate the slides. Incubate the assay slide at room temperature for 1 h with a relative humidity of 60%. Wash, block, and dry the assay slide as described in steps 1.1.3 - 1.1.5.</li>
		<li>Place another transfer slide on the inkjet spotter deck and push against the bottom left corner. Spot dAb solutions containing 50 or 100 &#181;g/mL of antibodies (see Table 1), 20% glycerol, and 1% BSA in PBS. Ensure that each spot is 0.8 nL and the center-to-center spacing between spots is 400 &#181;m.</li>
		<li>Store the assay and the transfer slide. Seal both assay and transfer slides in an airtight bag containing desiccant and put in a -20 &#176;C freezer.</li>
	</ol>
	</li>
</ol>
2. Multiplexed immunoassays with snap chips
<ol>
	<li>Retrieve the assay slide from the freezer. Leave the bag sealed for 30 min until the slide comes to room temperature.</li>
	<li>Prepare 7-point serial diluted sample solutions by spiking proteins in PBS containing 0.05% Tween-20. 
	NOTE: Here, a 5-fold dilution factor is used. The starting concentrations for each protein are listed in Table 1.</li>
	<li>Prepare sample solutions as appropriate. For example, dilute human serum 4 times in PBST buffer.</li>
	<li>Clamp a 16-compartment gasket on the assay slide.</li>
	<li>Fill one column of 8 wells with the 7 protein dilution solutions and a protein-free PBST buffer solution by pipetting. Pipette the sample solutions in the other 8 wells on the same slide. 
	NOTE: 80 &#181;L solutions can be fit in each well. More slides can be used to measure additional samples when necessary.</li>
	<li>Incubate the samples on a shaker at 450 rpm either for 1 h at room temperature or for overnight at 4 &#176;C. Wash the slide three times with PBST on the shaker at 450 rpm, 5 min each time. Remove the gasket and dry the slide under a stream of nitrogen gas.</li>
	<li>Retrieve the transfer slide with dAbs from the freezer. Keep the bag sealed for 30 min at room temperature. Then, incubate the slide in a closed chamber (e.g. empty tips box) containing 60% humidity stabilization beads for 20 min for rehydration.</li>
	<li>Snap the transfer slide with the assay slide using a snap apparatus (Figure 2) to transfer the dAb droplets. See section 1.2.2 for the operation of the snap apparatus.</li>
	<li>Separate the slides. Incubate the assay slide in a closed chamber containing 60% humidity stabilization beads for 1 h. Clamp the assay slide with a 16-compartment gasket and rinse the slide 4 times using PBST on a shaker at 450 rpm, 5 min each time.</li>
	<li>Pipette 80 &#181;L of solutions containing 2.5 &#181;g/mL streptavidin fluorophore in PBS into each well. Incubate for 20 min on a shaker at 450 rpm.</li>
	<li>Rinse the slide 3 times with PBST and once with distilled water on the shaker at 450 rpm. Remove the gasket and dry the slide using nitrogen gas.</li>
</ol>
3. Slide scanning and data analysis
<ol>
	<li>Scan the assay slide with a fluorescence microarray scanner using the 635-nm-laser.</li>
	<li>Extract the net intensity of each spot using an analysis software (e.g. array-pro analyzer)16.</li>
	<li>Calculate the limit of detection (LOD) of each protein using a statistics software and determine the protein concentrations in the samples. 
	NOTE: The LOD is defined as the Y-intercept of the standard curve incremented by three times the standard deviation of three independent assays.</li>
</ol>

<ol>
	<li>Mor, G., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Serum+protein+markers+for+early+detection+of+ovarian+cancer.">Serum protein markers for early detection of ovarian cancer.</a> Proc. Natl. Acad. Sci. U.S.A. 102 (21), 7677-7682 (2005).</li><li>Nicolini, A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Intensive+post-operative+follow-up+of+breast+cancer+patients+with+tumour+markers:+CEA,+TPA+or+CA15.3+vs+MCA+and+MCA-CA15.3+vs+CEA-TPA-CA15.3+panel+in+the+early+detection+of+distant+metastases.">Intensive post-operative follow-up of breast cancer patients with tumour markers: CEA, TPA or CA15.3 vs MCA and MCA-CA15.3 vs CEA-TPA-CA15.3 panel in the early detection of distant metastases.</a> BMC Cancer. 6 (1), 1-9 (2006).</li><li>Hnasko, R., Lin, A., McGarvey, J. A., Stanker, L. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+rapid+method+to+improve+protein+detection+by+indirect+ELISA.">A rapid method to improve protein detection by indirect ELISA.</a> Biochem. Biophys. Res. Commun. 410 (4), 726-731 (2011).</li><li>Percy, A. J., Chambers, A. G., Yang, J., Hardie, D. B., Borchers, C. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Advances+in+multiplexed+MRM-based+protein+biomarker+quantitation+toward+clinical+utility.">Advances in multiplexed MRM-based protein biomarker quantitation toward clinical utility.</a> Biochim. Biophys. Acta - Proteins and Proteomics. 1844 (5), 917-926 (2014).</li><li>Ekins, R. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Multi-analyte+immunoassay.">Multi-analyte immunoassay.</a> J Pharm Biomed Anal. 7 (2), 155-168 (1989).</li><li>Mahlknecht, P., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+antibody+microarray+analysis+of+serum+cytokines+in+neurodegenerative+Parkinsonian+syndromes.">An antibody microarray analysis of serum cytokines in neurodegenerative Parkinsonian syndromes.</a> Proteome Sci. 10 (1), 71-80 (2012).</li><li>Miller, J. C., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Antibody+microarray+profiling+of+human+prostate+cancer+sera:+Antibody+screening+and+identification+of+potential+biomarkers.">Antibody microarray profiling of human prostate cancer sera: Antibody screening and identification of potential biomarkers.</a> Proteomics. 3 (1), 56-63 (2003).</li><li>Li, H., Leulmi, R. F., Juncker, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Hydrogel+droplet+microarrays+with+trapped+antibody-functionalized+beads+for+multiplexed+protein+analysis.">Hydrogel droplet microarrays with trapped antibody-functionalized beads for multiplexed protein analysis.</a> Lab Chip. 11 (3), 528-534 (2011).</li><li>Juncker, D., Bergeron, S., Laforte, V., Li, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Cross-reactivity+in+antibody+microarrays+and+multiplexed+sandwich+assays:+shedding+light+on+the+dark+side+of+multiplexing.">Cross-reactivity in antibody microarrays and multiplexed sandwich assays: shedding light on the dark side of multiplexing.</a> Curr. Opin. Chem. Biol. 18, 29-37 (2014).</li><li>Blank, K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Double-chip+protein+arrays:+force-based+multiplex+sandwich+immunoassays+with+increased+specificity.">Double-chip protein arrays: force-based multiplex sandwich immunoassays with increased specificity.</a> Anal. Bioanal. Chem. 379 (7), 974-981 (2004).</li><li>Albrecht, C., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=DNA:+A+Programmable+Force+Sensor.">DNA: A Programmable Force Sensor.</a> Science. 301 (5631), 367-370 (2003).</li><li>Pla-Roca, M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Antibody+Colocalization+Microarray:+A+Scalable+Technology+for+Multiplex+Protein+Analysis+in+Complex+Samples.">Antibody Colocalization Microarray: A Scalable Technology for Multiplex Protein Analysis in Complex Samples.</a> Mol. Cell. proteomics. 11 (4), (2012).</li><li>Li, H., Bergeron, S., Juncker, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Microarray-to-Microarray+Transfer+of+Reagents+by+Snapping+of+Two+Chips+for+Cross-Reactivity-Free+Multiplex+Immunoassays.">Microarray-to-Microarray Transfer of Reagents by Snapping of Two Chips for Cross-Reactivity-Free Multiplex Immunoassays.</a> Anal. Chem. 84 (11), 4776-4783 (2012).</li><li>Li, H., Munzar, J. D., Ng, A., Juncker, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+versatile+snap+chip+for+high-density+sub-nanoliter+chip-to-chip+reagent+transfer.">A versatile snap chip for high-density sub-nanoliter chip-to-chip reagent transfer.</a> Sci. Rep. 5, 11688 (2015).</li><li>Li, H., Bergeron, S., Annis, M. G., Siegel, P. M., Juncker, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Serial+analysis+of+38+proteins+during+the+progression+of+human+breast+tumor+in+mice+using+an+antibody+colocalization+microarray.">Serial analysis of 38 proteins during the progression of human breast tumor in mice using an antibody colocalization microarray.</a> Mol. Cell. Proteomics. 14, 1024-1037 (2015).</li><li>Bergeron, S., Laforte, V., Lo, P. S., Li, H., Juncker, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Evaluating+mixtures+of+14+hygroscopic+additives+to+improve+antibody+microarray+performance.">Evaluating mixtures of 14 hygroscopic additives to improve antibody microarray performance.</a> Anal. Bioanal. Chem. 407 (28), 8451-8462 (2015).</li><li>Whiteaker, J. R., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Sequential+Multiplexed+Analyte+Quantification+Using+Peptide+Immunoaffinity+Enrichment+Coupled+to+Mass+Spectrometry.">Sequential Multiplexed Analyte Quantification Using Peptide Immunoaffinity Enrichment Coupled to Mass Spectrometry.</a> Mol. Cell. Proteomics. 11 (6), (2012).</li><li>Xu, K., Wang, X., Ford, R. M., Landers, J. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Self-Partitioned+Droplet+Array+on+Laser-Patterned+Superhydrophilic+Glass+Surface+for+Wall-less+Cell+Arrays.">Self-Partitioned Droplet Array on Laser-Patterned Superhydrophilic Glass Surface for Wall-less Cell Arrays.</a> Anal. Chem. 88 (5), 2652-2658 (2016).</li><li>Lee, M. -. Y., Park, C. B., Dordick, J. S., Clark, D. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Metabolizing+enzyme+toxicology+assay+chip+(MetaChip)+for+high-throughput+microscale+toxicity+analyses.">Metabolizing enzyme toxicology assay chip (MetaChip) for high-throughput microscale toxicity analyses.</a> Proc. Natl. Acad. Sci. U.S.A. 102 (4), 983-987 (2005).</li><li>Fernandes, T. G., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Three-dimensional+cell+culture+microarray+for+high-throughput+studies+of+stem+cell+fate.">Three-dimensional cell culture microarray for high-throughput studies of stem cell fate.</a> Biotechnol. Bioeng. 106 (1), 106-118 (2010).</li><li>Kwon, C. H., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Drug-Eluting+Microarrays+for+Cell-Based+Screening+of+Chemical-Induced+Apoptosis.">Drug-Eluting Microarrays for Cell-Based Screening of Chemical-Induced Apoptosis.</a> Anal. Chem. 83 (11), 4118-4125 (2011).</li><li>Jogia, G. E., Tronser, T., Popova, A. A., Levkin, P. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Droplet+Microarray+Based+on+Superhydrophobic-Superhydrophilic+Patterns+for+Single+Cell+Analysis.">Droplet Microarray Based on Superhydrophobic-Superhydrophilic Patterns for Single Cell Analysis.</a> Microarrays. 5 (4), 28 (2016).</li><li>Schena, M., Shalon, D., Davis, R. W., Brown, P. O. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Quantitative+Monitoring+of+Gene+Expression+Patterns+with+a+Complementary+DNA+Microarray.">Quantitative Monitoring of Gene Expression Patterns with a Complementary DNA Microarray.</a> Science. 270 (5235), 467-470 (1995).</li><li>Wu, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+sandwiched+microarray+platform+for+benchtop+cell-based+high+throughput+screening.">A sandwiched microarray platform for benchtop cell-based high throughput screening.</a> Biomaterials. 32 (3), 841-848 (2011).</li></ol>

McGill University has filed a patent application on some aspects of this work with Huiyan Li and David Juncker as inventors.

In this work, we have presented a snap chip technology that makes the cross-reactivity-free multiplex immunoassays widely available for the researchers with basic experimental setup. Different from existing antibody microarrays, no microarray spotter is needed for end-users. Both single and double transfer methods are demonstrated, and double transfer affords superior alignment accuracy down to ~ 40 &#956;m for 98% spots, with the largest misalignment of 63 &#181;m14. A novel snap apparatus was de...

A panel of biomarkers comprising multiple proteins may provide higher sensitivity and specificity than a single biomarker in the diagnosis of complex diseases such as cancers1,2. The enzyme-linked immunosorbent assay (ELISA) has been the gold standard technology used in clinical laboratories achieving a limit of detection at low pg/mL in plasma, but limits to one target per assay3,4,5. Antibody microarrays have been developed for accommodating thousands of miniaturized assays conducted in parallel on a single microscope slide6,7,8. However, the multiplexing capability of this method is limited by reagent-driven cross-reactivity, arising from the application of a mixture of dAbs, and it becomes more problematic with an increasing number of targets9,10,11. Pla et al. have stated that the resulting vulnerability of a multiplex sandwich assay scales as 4N(N-1) where N is the number of the targets12.
To mitigate cross-reactivity in antibody microarrays, antibody colocalization microarray (ACM) has been developed in our laboratory for multiplex sandwich assay12. Capture antibodies (cAbs) are spotted on a substrate with a microarray spotter. After blocking samples are applied on the surface, and then individual dAbs are spotted on the same spots with the cAb-antigen complex. All cross-reactivity scenarios between antibodies and antigens can be mitigated with ACM, and limits of detection at pg/mL have been achieved. However, the assay protocol requires preparing and spotting the dAbs during the experiments using an on-site microarray spotter with high precision for alignment purpose, which is expensive and time consuming, limiting the wide application of this technology in other laboratories. A handheld ACM, named snap chip has been developed for cross-reactivity-free and spotter-free multiplex sandwich immunoassays13,14,15. cAbs and dAbs are pre-spotted onto an assay slide and a transfer slide respectively in microarray format and stored. During the assay, the slides are retrieved and a microarray of dAbs are transferred collectively onto the assay slide by simply snapping the two chips together. A snap apparatus is used for reliable reagent transfer. Nitrocellulose coated slides with a relatively large antibody binding capacity have been used as the assay slides to absorb the liquid droplets and thus facilitating reagent transfer, however, the slides are more expensive than regular glass slides and microarray scanners compatible with non-transparent slides are needed for signal acquisition.
In this work, we demonstrate the protocol of performing a multiplex sandwich immunoassay with a snap chip. A novel snap apparatus has been developed for more convenient and reliable reagent transfer from microarray-to-microarray. Importantly, here we have established the reagent transfer method onto regular glass slides with the snap chip. 1024 spots were successfully transferred and aligned onto a glass slide, significantly expanding the use of this technology in most laboratories.

<table>
	<tbody>
		<tr>
			<td>Phosphate buffered saline tablet</td>
			<td>Fisher Scientific</td>
			<td>5246501EA</td>
			<td></td>
		</tr>
		<tr>
			<td>Streptavidin-conjugated Cy5</td>
			<td>Rockland</td>
			<td>s000-06</td>
			<td></td>
		</tr>
		<tr>
			<td>Tween-20</td>
			<td>Sigma-Aldrich</td>
			<td>p1379</td>
			<td></td>
		</tr>
		<tr>
			<td>Bovine serum albumin</td>
			<td>Jackson ImmunoResearch Laboratories, Inc</td>
			<td>001-000-162</td>
			<td></td>
		</tr>
		<tr>
			<td>Glycerol</td>
			<td>Sigma-Aldrich</td>
			<td>G5516</td>
			<td></td>
		</tr>
		<tr>
			<td>Blocking solution: BSA-free StabilGuard Choice Microarray Stabilizer</td>
			<td>SurModics, Inc</td>
			<td>SG02</td>
			<td></td>
		</tr>
		<tr>
			<td>Nitrocellulose coated slides</td>
			<td>Grace Bio-Laboratories, Inc</td>
			<td>305116</td>
			<td></td>
		</tr>
		<tr>
			<td>Aminosilane coated slides</td>
			<td>Schott North America</td>
			<td>1064875</td>
			<td></td>
		</tr>
		<tr>
			<td>Snap Device</td>
			<td>Parallex BioAssays Inc.</td>
			<td>PBA-SD01</td>
			<td></td>
		</tr>
		<tr>
			<td>Inkjet microarray spotter</td>
			<td>GeSiM</td>
			<td>Nanoplotter 2.0</td>
			<td></td>
		</tr>
		<tr>
			<td>Slide module gasket</td>
			<td>Grace Bio-Laboratories, Inc</td>
			<td>204862</td>
			<td></td>
		</tr>
		<tr>
			<td>Humidity Stabilization Beads</td>
			<td>Parallex BioAssays Inc.</td>
			<td>PBA-HU60</td>
			<td></td>
		</tr>
		<tr>
			<td>Array-Pro Analyzer software</td>
			<td>Media Cybernetics</td>
			<td>Version 4.5</td>
			<td></td>
		</tr>
		<tr>
			<td>Fluorescence microarray scanner</td>
			<td>Agilent</td>
			<td>SureScan Microarray Scanner</td>
			<td></td>
		</tr>
		<tr>
			<td>Biostatistics software</td>
			<td>GraphPad Software</td>
			<td>GraphPad Prism 6</td>
			<td></td>
		</tr>
		<tr>
			<td>Endoglin capture antibody</td>
			<td>R&#38;D Systems</td>
			<td>MAB10972</td>
			<td></td>
		</tr>
		<tr>
			<td>Endoglin protein</td>
			<td>R&#38;D Systems</td>
			<td>1097-EN</td>
			<td></td>
		</tr>
		<tr>
			<td>Endoglin detection antibody</td>
			<td>R&#38;D Systems</td>
			<td>BAF1097</td>
			<td></td>
		</tr>
		<tr>
			<td>IL-6a (see Table 1)</td>
			<td>R&#38;D Systems</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>IL-6b (see Table 1)</td>
			<td>Invitrogen</td>
			<td></td>
			<td></td>
		</tr>
	</tbody>
</table>

snap chip for cross-reactivity-free and spotter-free multiplexed sandwich immunoassays

Multiplexed protein analysis has shown superior diagnostic sensitivity and accuracy compared to single proteins. Antibody microarrays allow for thousands of micro-scale immunoassays performed simultaneously on a single chip. Sandwich assay format improves assay specificity by detecting each target with two antibodies, but suffers from cross-reactivity between reagents thus limiting their multiplexing capabilities. Antibody colocalization microarray (ACM) has been developed for cross-reactivity-free multiplexed protein detection, but requires an expensive spotter on-site for microarray fabrication during assays. In this work, we demonstrate a snap chip technology that transfers reagent from microarray-to-microarray by simply snapping two chips together, thus no spotter is needed during the sample incubation and subsequent application of detection antibodies (dAbs) upon storage of pre-spotted slides, dissociating the slide preparation from assay execution. Both single and double transfer methods are presented to achieve accurate alignment between the two microarrays and the slide fabrication for both methods are described. Results show that &#60;40 &#956;m alignment has been achieved with double transfer, reaching an array density of 625 spots/cm2. A 50-plexed immunoassay has been conducted to demonstrate the usability of the snap chip in multiplexed protein analysis. Limits of detection of 35 proteins are in the range of pg/mL.

The assay procedure for both single and double transfer methods is shown in Figure 1. In single transfer, the cAbs are spotted directly on the assay slide and the dAbs are transferred onto the assay slide upon use in a mirror pattern of the cAbs (Figure 1a). Only one transfer procedure is required, but this method suffers from misalignment between the two microarrays, mainly caused by the angular misalignment between the slide an...

Watch this Scientific Journal Video about Snap Chip for Cross-reactivity-free and Spotter-free Multiplexed Sandwich Immunoassays at JoVE.com

Snap Chip for Cross-reactivity-free and Spotter-free Multiplexed Sandwich Immunoassays

We demonstrate a snap chip technology for performing cross-reactivity-free multiplexed sandwich immunoassays by simply snapping two slides. A snap apparatus is used for reliably transferring reagents from microarray-to-microarray. The snap chip can be used for any biochemical reactions requiring colocalization of different reagents without cross-contamination.

Multiplexed protein analysis has shown superior diagnostic sensitivity and accuracy compared to single proteins. Antibody microarrays allow for thousands ...

snap-chip-for-cross-reactivity-free-spotter-free-multiplexed-sandwich

Research

JoVE Journal

Bioengineering

6.4K Views.  McGill University and Génome Québec Innovation Centre. We tonen een module chiptechnologie voor het uitvoeren van cross-country-reactivity-vrije multiplexed sandwich-immunoassay door simpelweg twee dia's uitlijnen. Een apparaat module wordt gebruikt voor het op betrouwbare wijze overbrengen van reagentia van microarray-naar-microarray. De module-chip kan worden gebruikt voor alle biochemische reacties vereisen colocalization van verschillende reagentia zonder kruisbesmetting.

Video: Snap Chip for Cross-reactivity-free and Spotter-free Multiplexed Sandwich Immunoassays

Fluorescence detection methods for microfluidic droplet platforms

The development of microfluidic platforms for performing chemistry and biology has in large part been driven by a range of potential benefits that accompany system miniaturisation. Advantages include the ability to efficiently process nano- to femoto- liter volumes of sample, facile integration of functional components, an intrinsic predisposition towards large-scale multiplexing, enhanced analytical throughput, improved control and reduced instrumental footprints.1
In recent years much interest has focussed on the development of droplet-based (or segmented flow) microfluidic systems and their potential as platforms in high-throughput experimentation.2-4 Here water-in-oil emulsions are made to spontaneously form in microfluidic channels as a result of capillary instabilities between the two immiscible phases. Importantly, microdroplets of precisely defined volumes and compositions can be generated at frequencies of several kHz. Furthermore, by encapsulating reagents of interest within isolated compartments separated by a continuous immiscible phase, both sample cross-talk and dispersion (diffusion- and Taylor-based) can be eliminated, which leads to minimal cross-contamination and the ability to time analytical processes with great accuracy. Additionally, since there is no contact between the contents of the droplets and the channel walls (which are wetted by the continuous phase) absorption and loss of reagents on the channel walls is prevented.
Once droplets of this kind have been generated and processed, it is necessary to extract the required analytical information. In this respect the detection method of choice should be rapid, provide high-sensitivity and low limits of detection, be applicable to a range of molecular species, be non-destructive and be able to be integrated with microfluidic devices in a facile manner. To address this need we have developed a suite of experimental tools and protocols that enable the extraction of large amounts of photophysical information from small-volume environments, and are applicable to the analysis of a wide range of physical, chemical and biological parameters. Herein two examples of these methods are presented and applied to the detection of single cells and the mapping of mixing processes inside picoliter-volume droplets. We report the entire experimental process including microfluidic chip fabrication, the optical setup and the process of droplet generation and detection.

Droplet-based microfluidic platforms are promising candidates for high throughput experimentation since they are able to generate picoliter, self-compartmentalized vessels inexpensively at kHz rates. Through integration with fast, sensitive and high resolution fluorescence spectroscopic methods, the large amounts of information generated within these systems can be efficiently extracted, harnessed and utilized.

The development of microfluidic platforms for performing chemistry and biology has in large part been driven by a range of potential benefits that ...

On-chip Isotachophoresis for Separation of Ions and Purification of Nucleic Acids

Electrokinetic techniques are a staple of microscale applications because of their unique ability to perform a variety of fluidic and electrophoretic processes in simple, compact systems with no moving parts. Isotachophoresis (ITP) is a simple and very robust electrokinetic technique that can achieve million-fold preconcentration1,2 and efficient separation and extraction based on ionic mobility.3 For example, we have demonstrated the application of ITP to separation and sensitive detection of unlabeled ionic molecules (e.g. toxins, DNA, rRNA, miRNA) with little or no sample preparation4-8 and to extraction and purification of nucleic acids from complex matrices including cell culture, urine, and blood.9-12
ITP achieves focusing and separation using an applied electric field and two buffers within a fluidic channel system. For anionic analytes, the leading electrolyte (LE) buffer is chosen such that its anions have higher effective electrophoretic mobility than the anions of the trailing electrolyte (TE) buffer (Effective mobility describes the observable drift velocity of an ion and takes into account the ionization state of the ion, as described in detail by Persat et al.13). After establishing an interface between the TE and LE, an electric field is applied such that LE ions move away from the region occupied by TE ions. Sample ions of intermediate effective mobility race ahead of TE ions but cannot overtake LE ions, and so they focus at the LE-TE interface (hereafter called the "ITP interface"). Further, the TE and LE form regions of respectively low and high conductivity, which establish a steep electric field gradient at the ITP interface. This field gradient preconcentrates sample species as they focus. Proper choice of TE and LE results in focusing and purification of target species from other non-focused species and, eventually, separation and segregation of sample species.
We here review the physical principles underlying ITP and discuss two standard modes of operation: "peak" and "plateau" modes. In peak mode, relatively dilute sample ions focus together within overlapping narrow peaks at the ITP interface. In plateau mode, more abundant sample ions reach a steady-state concentration and segregate into adjoining plateau-like zones ordered by their effective mobility. Peak and plateau modes arise out of the same underlying physics, but represent distinct regimes differentiated by the initial analyte concentration and/or the amount of time allotted for sample accumulation.
We first describe in detail a model peak mode experiment and then demonstrate a peak mode assay for the extraction of nucleic acids from E. coli cell culture. We conclude by presenting a plateau mode assay, where we use a non-focusing tracer (NFT) species to visualize the separation and perform quantitation of amino acids.

Isotachophoresis (ITP) is a robust electrokinetic separation and preconcentration technique with applications ranging from toxin detection to sample preparation. We review the physical principles of ITP and the methodology of applying this technique to two specific example applications: separation and detection of small molecules and purification of nucleic acids from cell culture lysate.

Electrokinetic techniques are a staple of microscale applications because of their unique ability to perform a variety of fluidic and electrophoretic ...

Hollow Microneedle-based Sensor for Multiplexed Transdermal Electrochemical Sensing

The development of a minimally invasive multiplexed monitoring system for rapid analysis of biologically-relevant molecules could offer individuals suffering from chronic medical conditions facile assessment of their immediate physiological state. Furthermore, it could serve as a research tool for analysis of complex, multifactorial medical conditions. In order for such a multianalyte sensor to be realized, it must be minimally invasive, sampling of interstitial fluid must occur without pain or harm to the user, and analysis must be rapid as well as selective.
Initially developed for pain-free drug delivery, microneedles have been used to deliver vaccines and pharmacologic agents (e.g., insulin) through the skin.1-2 Since these devices access the interstitial space, microneedles that are integrated with microelectrodes can be used as transdermal electrochemical sensors. Selective detection of glucose, glutamate, lactate, hydrogen peroxide, and ascorbic acid has been demonstrated using integrated microneedle-electrode devices with carbon fibers, modified carbon pastes, and platinum-coated polymer microneedles serving as transducing elements.3-7,8
This microneedle sensor technology has enabled a novel and sophisticated analytical approach for in situ and simultaneous detection of multiple analytes. Multiplexing offers the possibility of monitoring complex microenvironments, which are otherwise difficult to characterize in a rapid and minimally invasive manner. For example, this technology could be utilized for simultaneous monitoring of extracellular levels of, glucose, lactate and pH,9 which are important metabolic indicators of disease states7,10-14 (e.g., cancer proliferation) and exercise-induced acidosis.15

This article details the construction of a multiplexed microneedle-based sensor. The device is being developed for in situ sampling and electrochemical analysis of multiple analytes in a rapid and selective manner. We envision clinical medicine and biomedical research uses for these microneedle-based sensors.

The development of a minimally invasive multiplexed monitoring system for rapid analysis of biologically-relevant molecules could offer individuals ...

A Microfluidic Chip for the Versatile Chemical Analysis of Single Cells

We present a microfluidic device that enables the quantitative determination of intracellular biomolecules in multiple single cells in parallel. For this purpose, the cells are passively trapped in the middle of a microchamber. Upon activation of the control layer, the cell is isolated from the surrounding volume in a small chamber. The surrounding volume can then be exchanged without affecting the isolated cell. However, upon short opening and closing of the chamber, the solution in the chamber can be replaced within a few hundred milliseconds. Due to the reversibility of the chambers, the cells can be exposed to different solutions sequentially in a highly controllable fashion, e.g. for incubation, washing, and finally, cell lysis. The tightly sealed microchambers enable the retention of the lysate, minimize and control the dilution after cell lysis. Since lysis and analysis occur at the same location, high sensitivity is retained because no further dilution or loss of the analytes occurs during transport. The microchamber design therefore enables the reliable and reproducible analysis of very small copy numbers of intracellular molecules (attomoles, zeptomoles) released from individual cells. Furthermore, many microchambers can be arranged in an array format, allowing the analysis of many cells at once, given that suitable optical instruments are used for monitoring. We have already used the platform for proof-of-concept studies to analyze intracellular proteins, enzymes, cofactors and second messengers in either relative or absolute quantifiable manner.

In this article we present a microfluidic chip for single cell analysis. It allows the quantification of intracellular proteins, enzymes, cofactors, and second messengers by means of fluorescent assays or immunoassays.&#160;

We present a microfluidic device that enables the quantitative determination of intracellular biomolecules in multiple single cells in parallel. For this ...

Stress-induced Antibiotic Susceptibility Testing on a Chip

We have developed a rapid microfluidic method for antibiotic susceptibility testing in a stress-based environment. Fluid is passed at high speeds over bacteria immobilized on the bottom of a microfluidic channel. In the presence of stress and antibiotic, susceptible strains of bacteria die rapidly. However, resistant bacteria survive these stressful conditions. The hypothesis behind this method is new: stress activation of biochemical pathways, which are targets of antibiotics, can accelerate antibiotic susceptibility testing. As compared to standard antibiotic susceptibility testing methods, the rate-limiting step -&#160;bacterial growth -&#160;is omitted during antibiotic application. The technical implementation of the method is in a combination of standard techniques and innovative approaches. The standard parts of the method include bacterial culture protocols, defining microfluidic channels in polydimethylsiloxane&#160;(PDMS), cell viability monitoring with fluorescence, and batch image processing for bacteria counting. Innovative parts of the method are in the use of culture media flow for mechanical stress application, use of enzymes to damage but not kill the bacteria, and use of microarray substrates for bacterial attachment. The developed platform can be used in antibiotic and nonantibiotic related drug development and testing. As compared to the standard bacterial suspension experiments, the effect of the drug can be turned on and off repeatedly over controlled time periods. Repetitive observation of the same bacterial population is possible over the course of the same experiment.

We have developed a microfluidic platform for rapid antibiotic susceptibility testing. Fluid is passed at high speeds over bacteria immobilized on the bottom of a microfluidic channel. In the presence of stress and antibiotic, susceptible strains of bacteria die rapidly. However, resistant bacteria can survive these stressful conditions.

We have developed a rapid microfluidic method for antibiotic susceptibility testing in a stress-based environment. Fluid is passed at high speeds over ...

A Microfluidic Chip for ICPMS Sample Introduction

This protocol discusses the fabrication and usage of a disposable low cost microfluidic chip as sample introduction system for inductively coupled plasma mass spectrometry (ICPMS). The chip produces monodisperse aqueous sample droplets in perfluorohexane (PFH). Size and frequency of the aqueous droplets can be varied in the range of 40 to 60 &#181;m and from 90 to 7,000&#160;Hz, respectively. The droplets are ejected from the chip with a second flow of PFH and remain intact during the ejection. A custom-built desolvation system removes the PFH and transports the droplets into the ICPMS. Here, very stable signals with a narrow intensity distribution can be measured, showing the monodispersity of the droplets. We show that the introduction system can be used to quantitatively determine iron in single bovine red blood cells. In the future, the capabilities of the introduction device can easily be extended by the integration of additional microfluidic modules.

We present a discrete droplet sample introduction system for inductively coupled plasma mass spectrometry (ICPMS). It is based on a cheap and disposable microfluidic chip that generates highly monodisperse droplets in a size range of 40&#8722;60 &#181;m at frequencies from 90 to 7,000 Hz.

This protocol discusses the fabrication and usage of a disposable low cost microfluidic chip as sample introduction system for inductively coupled plasma ...

Sandwich-like Microenvironments to Harness Cell/Material Interactions

Cell culture has been traditionally carried out on bi-dimensional (2D) substrates where cells adhere using ventral receptors to the biomaterial surface. However in vivo, most of the cells are completely surrounded by the extracellular matrix (ECM), resulting in a three-dimensional (3D) distribution of receptors. This may trigger differences in the outside-in signaling pathways and thus in cell behavior.
This article shows that stimulating the dorsal receptors of cells already adhered to a 2D substrate by overlaying a film of a new material (a sandwich-like culture) triggers important changes with respect to standard 2D cultures. Furthermore, the simultaneous excitation of ventral and dorsal receptors shifts cell behavior closer to that found in 3D environments. Additionally, due to the nature of the system, a sandwich-like culture is a versatile tool that allows the study of different parameters in cell/material interactions, e.g., topography, stiffness and different protein coatings at both the ventral and dorsal sides. Finally, since sandwich-like cultures are based on 2D substrates, several analysis procedures already developed for standard 2D cultures can be used normally, overcoming more complex procedures needed for 3D systems.

The following protocol describes the procedure to assemble sandwich-like cultures to be used as an intermediate stage between bi-dimensional (2D) and three-dimensional (3D) cellular environments. The engineered systems can have applications in microscopy, biomechanics, biochemistry and cell biology assays.

Cell culture has been traditionally carried out on bi-dimensional (2D) substrates where cells adhere using ventral receptors to the biomaterial surface. ...

Gradient Strain Chip for Stimulating Cellular Behaviors in Cell-laden Hydrogel

Artificial guidance for cellular alignment is a hot topic in the field of tissue engineering. Most of the previous research has investigated single strain-induced cellular alignment on a cell-laden hydrogel by using complex experimental processes and mass controlling systems, which are usually associated with contamination issues. Thus, in this article, we propose a simple approach to building a gradient static strain using a fluidic chip with a plastic PDMS cover and a UV transparent glass substrate for the stimulation of cellular behavior in a 3D hydrogel. Overloading photo-patternable cell prepolymer in the fluidic chamber can generate a convex curved PDMS membrane on the cover. After UV crosslinking, through a concentric circular micropattern under the curved PDMS membrane, and buffer washing, a microenvironment for investigating cell behaviors under a variety of gradient strains is self-established in a single fluidic chip, without external instruments. NIH3T3 cells were demonstrated after observing the change in the cellular alignment trend under geometry guidance, in cooperation with strain stimulation, which varied from 15 - 65% on hydrogels. After a 3-day incubation, the hydrogel geometry dominated the cell alignment under low compressive strain, where cells aligned along the hydrogel elongation direction under high compressive strain. Between these, the cells showed random alignment due to the dissipation of the radical guidance of hydrogel elongation and the geometry guidance of the patterned hydrogel.

This article introduces a simple approach to providing non-continuous gradient static strains on a concentric cell-laden hydrogel to regulate cell alignment for tissue engineering.

Artificial guidance for cellular alignment is a hot topic in the field of tissue engineering. Most of the previous research has investigated single ...

Fabrication of Three-dimensional Paper-based Microfluidic Devices for Immunoassays

Paper wicks fluids autonomously due to capillary action. By patterning paper with hydrophobic barriers, the transport of fluids can be controlled and directed within a layer of paper. Moreover, stacking multiple layers of patterned paper creates sophisticated three-dimensional microfluidic networks that can support the development of analytical and bioanalytical assays. Paper-based microfluidic devices are inexpensive, portable, easy to use, and require no external equipment to operate. As a result, they hold great promise as a platform for point-of-care diagnostics. In order to properly evaluate the utility and analytical performance of paper-based devices, suitable methods must be developed to ensure their manufacture is reproducible and at a scale that is appropriate for laboratory settings. In this manuscript, a method to fabricate a general device architecture that can be used for paper-based immunoassays is described. We use a form of additive manufacturing (multi-layer lamination) to prepare devices that comprise multiple layers of patterned paper and patterned adhesive. In addition to demonstrating the proper use of these three-dimensional paper-based microfluidic devices with an immunoassay for human chorionic gonadotropin (hCG), errors in the manufacturing process that may result in device failures are discussed. We expect this approach to manufacturing paper-based devices will find broad utility in the development of analytical applications designed specifically for limited-resource settings.

We detail a method to fabricate three-dimensional paper-based microfluidic devices for use in the development of immunoassays. Our approach to device assembly is a type of multilayer, additive manufacturing. We demonstrate a sandwich immunoassay to provide representative results for these types of paper-based devices.

Paper wicks fluids autonomously due to capillary action. By patterning paper with hydrophobic barriers, the transport of fluids can be controlled and ...

Microfluidic Platform with Multiplexed Electronic Detection for Spatial Tracking of Particles

Microfluidic processing of biological samples typically involves differential manipulations of suspended particles under various force fields in order to spatially fractionate the sample based on a biological property of interest. For the resultant spatial distribution to be used as the assay readout, microfluidic devices are often subjected to microscopic analysis requiring complex instrumentation with higher cost and reduced portability. To address this limitation, we have developed an integrated electronic sensing technology for multiplexed detection of particles at different locations on a microfluidic chip. Our technology, called Microfluidic CODES, combines Resistive Pulse Sensing with Code Division Multiple Access to compress 2D spatial information into a 1D electrical signal. In this paper, we present a practical demonstration of the Microfluidic CODES technology to detect and size cultured cancer cells distributed over multiple microfluidic channels. As validated by the high-speed microscopy, our technology can accurately analyze dense cell populations all electronically without the need for an external instrument. As such, the Microfluidic CODES can potentially enable low-cost integrated lab-on-a-chip devices that are well suited for the point-of-care testing of biological samples.

We demonstrate a microfluidic platform with an integrated surface electrode network that combines resistive pulse sensing (RPS) with code division multiple access (CDMA), to multiplex detection and sizing of particles in multiple microfluidic channels.

Microfluidic processing of biological samples typically involves differential manipulations of suspended particles under various force fields in order to ...

Snap Chip for Cross-reactivity-free and Spotter-free Multiplexed Sandwich Immunoassays

Samenvatting

Meer video's verkennen

Hoofdstukken in deze video