Protocol for Long Duration Whole Body Hyperthermia in Mice

Podsumowanie

This paper describes a protocol for whole body hyperthermia in mice that can stimulate fever like conditions up to 12-24 hr.

Streszczenie

Hyperthermia is a general term used to define the increase in core body temperature above normal. It is often used to describe the increased core body temperature that is observed during fever. The use of hyperthermia as an adjuvant has emerged as a promising procedure for tumor regression in the field of cancer biology. For this purpose, the most important requirement is to have reliable and uniform heating protocols. We have developed a protocol for hyperthermia (whole body) in mice. In this protocol, animals are exposed to cycles of hyperthermia for 90 min followed by a rest period of 15 min. During this period mice have easy access to food and water. High body temperature spikes in the mice during first few hyperthermia exposure cycles are prevented by immobilizing the animal. Additionally, normal saline is administered in first few cycles to minimize the effects of dehydration. This protocol can simulate fever like conditions in mice up to 12-24 hr. We have used 8-12 weeks old BALB/Cj female mice to demonstrate the protocol.

Protokół

1. Animal Ethics

Before performing the long duration hyperthermia on mice make sure that the procedure has been approved by Institutional Animal Care and Use Committee. All the procedures discussed in this paper and shown in the accompanying video were approved by the Institutional Animal Ethics Committee of the National Institute of Immunology.

2. Understanding Hyperthermia

Whole Body Hyperthermia (WBH) is delivered by placing the animals in prewarmed cages that are placed in incubator maintained at 39.5°C. During the standardization of protocol, a temperature sensor was surgically implanted in the mice and their body temperature was monitored in different experimental conditions. It was observed that upon placing the animals in heated environment, their temperature gradually increased from 37 °C to up to 42 °C over the duration of 100 min (Figure 1). The resulting "spike" in temperature is intriguing as the internal body temperature shot even higher than the external environmental temperature.

When the body temperature exceeded 40 °C, the animal would show signs of stress and dehydration such as wetting around the snout. Increase the body temperature beyond 40 °C, will lead to wetting and irreversible stress or even death of animals due to heat stress. So it is important to prevent the temperature spikes during the course of hyperthermia.

This phenomenon of high temperature spikes is associated with the physical hyperactivity of animal during hyperthermia exposure. Similar temperature spikes were observed by other groups too and were associated with the physical hyperactivity of the animal upon being introduced to environment having higher temperatures ¹⁰.

In our protocol, mice are immobilized during the hyperthermia exposure. As shown in Figure 2, immobilization of animal prevents the temperature spikes.

We have used 8-12 weeks old BALB/Cj mice for demonstrating this protocol. The protocol is not restricted to a particular type/strain of the mice.

3. Preparing for the Experiment

3.1 Incubator

This experiment can be performed in a normal CO₂ incubator as they have a good temperature control. Disconnect CO₂ gas supply and remove water holding tray of the CO₂ incubator. In some models of incubators it is possible to switch off the CO₂ controller. Arrange shelves of the incubator so that a mice cage could be placed conveniently inside. Set the temperature of the incubator at 39.5 °C.

3.2 Cages

Typically, the hyperthermia experiment is performed on 4 mice at a time. Two cages are required; one is placed inside the incubator and the other is placed outside at room temperature. Bedding of cages is avoided, as the patches of bedding become wet with time which results in non-uniform temperature inside the cage. The outside cage should have food pellets and water bottle.

3.3 Mice immobilization tubes

During the course of first 4 cycles of hyperthermia mice are immobilized in perforated tubes. These immobilization tubes can be made from 50 ml 'centrifuge' tubes by piercing 3 mm holes all over its body and four of such tubes will be required. The 50ml tube can conveniently immobilize BALB/Cj mice which are older than 8 weeks. Tubes of appropriate sizes may be required for some unusually different strain of mice or for mice which are very young or older than 50 weeks.

Place immobilization tubes and a cage inside the incubator maintained at 39.5 °C. Wait for at least 2 hour so that the cage and immobilization tubes attain the temperature of the incubator.

4. First cycle of the Hyperthermia

Mice may experience dehydration during the hyperthermia exposure. Therefore before beginning the experiment, administer 0.5 ml normal saline intraperitoneally to every mouse. Use a 26 G needle with 1 ml syringe.

Quickly take out the cage placed in the incubator, place one animal in each immobilization tubes and place the cage back in the incubator. Record the time. It is essential to keep the cage at the same place in the incubator every time.

After 90 min, take out the cage from the incubator. Release animals from the immobilization tubes and place them in the cage at normal temperature with easy access to food and water. Place empty immobilization tubes back in the incubator.

After 15 min, the second cycle of hyperthermia is started by delivering 0.5 ml saline intraperitoneally to every mouse.

They are then immobilized in 50 ml perforated immobilization tubes and placed in the incubator.

5. Subsequent Hyperthermia Cycles

For first 4 cycles, it is essential to immobilize mice during the hyperthermia exposure and for the first two cycles, saline injection is given before beginning the hyperthermia period.

After these cycles of hyperthermia followed by rest are completed, mice get acclimatize and do not become hyperactive during the hyperthermia exposure. The intraperitoneal injection of saline may not be necessary if mice readily take food and water during the resting time.

6. After All the Cycles Completed, the Final Step is to Examine the Animals

There should not be any death during the hyperthermia cycles. Every animal has to be watched very carefully in the first few cycles. Rapidly look for any wetting around the snout. This symptom is a signature of dehydration. Mice with such symptoms should immediately be given 0.5 ml normal saline i.p and rest at room temperature. Most of the immobilized mice will not require any additional care and will successfully bear the stress the hyperthermia.

After completing required cycles, animals may look weak and dehydrated but they will quickly recover within few hours.

Figure 1. Variation of the core body temperature of Mice when the cage was placed in an incubator at 39.5 °C. After 90 min the cage was removed from the incubator and placed at 25 °C. Red circles indicate high temperature spikes.

Figure 2. Variation of the core body temperature of an immobilized Mice during the hyperthermia cycles. After immobilizing the animal, high temperatures spikes were not observe when the cage was placed at 39.5 °C.

Dyskusje

As far back as 5,000 B.C., Egyptian doctors treated tumors with heat. The Greeks recognized the value of heat in some medical treatments. The most ancient texts of the Law of Moses mention hot springs (Genesis 36:24) to therapeutically elevate body temperature.

The earlier techniques employed either the use of pyrogenic microbial extracts for induction of fever or hot water baths for induction of hyperthermia ¹. However none of these approaches could be easily monitored or controlle...

Materiały

Name	Company	Catalog Number	Comments
Thermistor	RS components	528-8558
CO2 Incubator	Heraeus	B5060 EK-CO2
Mice cages	Citizen industries ltd.		Type B 365X207X190 cm
Animal feed	Provimi India
Water bottle for cage	Local supplier		Glass bottle
Soldering iron	Solderon, India
50 ml Centrifuge tubes	BD Biosciences	352070
Timer	Local supplier
1 ml Syringe with 26G needle	BD Biosciences	309602
Saline	Local supplier