Ratiometric Imaging of Extracellular pH in Dental Biofilms

Podsumowanie

A pH-sensitive ratiometric dye is used in combination with confocal laser scanning microscopy and digital image analysis to monitor extracellular pH in dental biofilms in real-time.

Streszczenie

The pH in bacterial biofilms on teeth is of central importance for dental caries, a disease with a high worldwide prevalence. Nutrients and metabolites are not distributed evenly in dental biofilms. A complex interplay of sorption to and reaction with organic matter in the biofilm reduces the diffusion paths of solutes and creates steep gradients of reactive molecules, including organic acids, across the biofilm. Quantitative fluorescent microscopic methods, such as fluorescence life time imaging or pH ratiometry, can be employed to visualize pH in different microenvironments of dental biofilms. pH ratiometry exploits a pH-dependent shift in the fluorescent emission of pH-sensitive dyes. Calculation of the emission ratio at two different wavelengths allows determining local pH in microscopic images, irrespective of the concentration of the dye. Contrary to microelectrodes the technique allows monitoring both vertical and horizontal pH gradients in real-time without mechanically disturbing the biofilm. However, care must be taken to differentiate accurately between extra- and intracellular compartments of the biofilm. Here, the ratiometric dye, seminaphthorhodafluor-4F 5-(and-6) carboxylic acid (C-SNARF-4) is employed to monitor extracellular pH in in vivo grown dental biofilms of unknown species composition. Upon exposure to glucose the dye is up-concentrated inside all bacterial cells in the biofilms; it is thus used both as a universal bacterial stain and as a marker of extracellular pH. After confocal microscopic image acquisition, the bacterial biomass is removed from all pictures using digital image analysis software, which permits to exclusively calculate extracellular pH. pH ratiometry with the ratiometric dye is well-suited to study extracellular pH in thin biofilms of up to 75 µm thickness, but is limited to the pH range between 4.5 and 7.0.

Wprowadzenie

The method described here allows monitoring extracellular pH in dental biofilms in the range between 4.5 and 7, using the ratiometric dye seminaphthorhodafluor-4F 5-(and-6) carboxylic acid (C-SNARF-4) in combination with confocal laser scanning microscopy and digital image analysis. The employed fluorescent dye is pH-sensitive and displays a shift in its fluorescent emission depending on the state of protonation. The fluorescent emission of the protonated molecule peaks at 580 nm, and the emission of the deprotonated molecule at 640 nm¹. The ratio of the fluorescent emission intensities in two detection windows comprising the two emission peaks (576 - 608 nm and 629 - 661 nm) thus reflects pH in the liquid phase, irrespective of dye concentration. With a pK_a of ~6.4 the dye is suitable to visualize pH in moderately acidic environments.

PH in bacterial biofilms is of central importance for all metabolic processes. In the case of dental biofilms, pH in the extracellular matrix is the key virulence factor for the development of dental caries. Extended periods with low pH at the biofilm-tooth interface lead to slow demineralization of the underlying enamel². Due to the complex three-dimensional architecture of biofilms, metabolites, including organic acids, are not uniformly distributed across the biofilm. Highly and less acidogenic microenvironments may be found in close spatial proximity³.

For decades, vertical pH gradients in biofilms were recorded with the help of microelectrodes^4-6. While they offer a good spatial resolution due to their small tip size, they are not well-suited to monitor horizontal gradients. Moreover, insertion of the electrode disturbs the biofilm mechanically. Quantitative fluorescent microscopic techniques offer the advantage of visualizing pH changes in different areas of a biofilm without mechanical interference. Different microscopic fields of view can be selected freely and imaged repeatedly over prolonged periods^1,7-9. However, when interpreting microscopic biofilm images, it is important to distinguish between fluorescence deriving from the microbial biomass and fluorescence deriving from the extracellular space. In acidic conditions, pH inside bacterial cells is different from pH in the extracellular matrix, as the bacteria actively transport protons across their cell membrane at the expense of adenosine triphosphate¹⁰. In the context of dental caries, intracellular bacterial pH does not have a direct impact on the underlying enamel whereas low extracellular pH leads to demineralization. Averaging pH in microscopic images that contain both bacteria-free areas and bacteria leads to erroneous results. The use of other stains along with the pH-sensitive dye in order to visualize the bacterial biomass and differentiate between extra- and intracellular areas brings about the risk of fluorescent contamination of the extracellular space and false measurements¹¹.

The present manuscript therefore describes the use of the ratiometric dye in a double function; both as a pH marker and as a universal bacterial stain. As the dye is up-concentrated in bacterial cells, the combination of confocal microscopic imaging and an accurate digital image analysis procedure allows determining extracellular pH in the range between 4.5 and 7.0 in thin dental biofilms.

Protokół

The experimental protocol was reviewed and approved by the Ethics Committee of Aarhus County (M-20100032).

1. Confocal Microscopic Calibration of the Ratiometric Dye

1. For image acquisition, use an inverted confocal microscope equipped with an incubator, a 63X/1.2-numeric aperture water immersion objective, a 543 nm laser line and a META detector.
2. Prepare HEPES buffer stock solutions (50 mM, adjusted to pH 4.5-8.5 in steps of 0.1 pH units). Pipette 100 µl of each solution into the wells of a clear-bottom 96-well plate for fluorescent microscopy.
3. Wear nitrile gloves when handling the ratiometric dye C-SNARF-4. Prepare a 1 mM stock solution of the dye in dimethyl sulfoxide. Add 5 µl of the stock solution to each well with HEPES buffer. Place the 96-well plate on the microscope.
4. Turn on the microscope. Open the microscope software. Click the following panels: Acquire → Laser; Acquire → Micro; Acquire → Config; Acquire → Scan; Acquire → Stage. Warm up the incubator to 37 °C.
5. Turn on the 543 nm laser line by clicking on the 543 nm laser and the "On" button in the "Laser Control" window. Choose the 63X/1.2-numeric aperture water immersion objective in the "Microscope Control" window.
6. Set the META detector to simultaneously monitor fluorescence within 576- to 608-nm (green) and 629- to 661 nm (red) intervals ("Configuration Control" → "ChS"). Adjust the laser power ("Configuration Control" → "Excitation"). Set the pinhole to yield an optical slice thickness of 1.6 µm ("Scan Control" → "Pinhole").
7. Acquire an image of each HEPES buffer solution, 5 µm above the glass bottom of the 96-well plate. Note: As soon as the focus plane is situated below the glass bottom, no fluorescent light can be seen on the screen. After every third image, set the laser power to zero and take an image for background subtraction.
8. Perform the calibration experiment in triplicate (1.2-1.7).
9. Determine the average fluorescent intensity and standard deviation in all red and green images.
   1. Calculate the ratio R and standard error of mean, S_R, for each image according to equations (1) and (2)
      (1)
      (2)
      g, r, s_g and s_r are the averages and standard deviations in the respective green and red images. b_g, b_r, s_bg and s_br are the corresponding values for the background images. n² is number of pixels imaged.
   2. Plot the calculated ratios for each pH value from the three replicate calibration experiments in a diagram and construct a fitted curve from this series of data points (i.e. using the software SigmaPlot 13). Make a mathematical function from the fitted curve that can convert ratios into pH values¹⁰.

2. Collection of In Situ Grown Dental Biofilm Samples

1. Select volunteers that fulfill inclusion and exclusion criteria relevant for the study. Make alginate impressions of their upper and lower dental arch. Make cast models from these impressions and manufacture an acrylic splint in the lower jaw. Design the splint with buccal acrylic flanges connected by a lingual orthodontic wire that allows the volunteer to bite into normal occlusion¹².
2. Drill recessions in the buccal flanges of the acrylic splint (Figure 1) with the help of dental acrylic burs to allow insertion of glass slabs for biofilm collection. The depth of the recessions should be at least 1.5 mm, while the width and length of the recessions may vary depending on the number of glass slabs to be inserted.
3. For biofilm collection, use custom-made non-fluorescent glass slabs (4 x 4 x 1 mm³) with a surface roughness of grit 1,200 in order to mimic the colonization pattern on natural enamel¹¹.
4. Sterilize the glass slabs by autoclaving prior to mounting. Mount the glass slabs with sticky wax in the depressions in the buccal flanges of each side slightly recessed to the surface of the acrylic surface in order to protect the biofilm from shear forces exerted by movement of the cheeks¹¹.
   Note: The number of glass slabs placed in a recession may vary between 3 and 14, depending on the aim of the study.
5. Insert the appliance in the mouth of the volunteer. Instruct the volunteer to retain the appliance intra-orally throughout the experimental period. Instruct the volunteer to store the appliance in an orthodontic retainer container with a piece of wet paper tissue (to keep it humid) at room temperature during tooth brushing and intake of food and beverages other than water. Instruct the volunteer to not touch the buccal acrylic flanges with the glass slabs while placing and removing the appliance.
   Note: The experimental period may vary depending on the aim of the study (one day to several weeks).
6. Carefully remove the glass slabs from the appliance at the end of the experimental period. Remove the sticky wax around the slabs with a knife and transfer them with a pair of tweezers to a closed container, the biofilm facing upward, until microscopic analysis. Keep the container humid with wet paper tissue. Perform pH imaging within few hours after biofilm collection.

3. Biofilm pH Imaging

1. Prepare salivary solution by adding dithiothreitol to collected saliva according to the method of de Jong et al.¹³. Titrate the salivary solution to pH 7.0 and add glucose to a concentration of 0.4 % (wt/vol). Pipette 100 µl per biofilm to be analyzed into a glass-bottom 96-well plate for microscopy. Add 5 µl of the ratiometric dye per well.
2. Place the 96-well plate on the microscope stage. Turn on the microscope and the 543 nm laser line. Warm up the incubator to 37 °C. Use the same microscope settings as for the calibration of the dye (see steps 1.5-1.6). Wait for 30 min, until the 96-well plate has reached working temperature.
3. Pick up one or more glass slabs with a slim set of tweezers and place them in the saliva-filled wells, one slab per well, with the biofilms facing downward.
4. Acquire single images ("Scan Control" → "Single") or z-stacks ("Scan Control" → "Start") spanning the depth of the biofilms in different areas. To acquire z-stacks choose the number of slices to be imaged ("Scan Control" → "Z Settings" → "Num Slices") and mark the z-position for the first and the last slice in the microscope software ("Scan Control" → "Z Settings" → "Mark First"; "Mark Last").
   Note: Z-stacks with a depth of up to 75 µm can be acquired with good contrast between extracellular and intracellular areas.
5. To follow pH changes in a microscopic field of view over time, mark the x-y-position in the microscope software ("Stage and Focus Control" → "Mark Pos") and take repeated images at consecutive time points ("Scan Control" → "Single"). Regularly take images with the laser power set to zero for background subtraction.

4. Digital Image Analysis

1. To export the microscopic images as TIF files, use the file batch export of the microscope software ("Macro" → "File Batch Export"). Mark the files to be exported and save red and green channel images in separate folders as TIF-files ("Start Batch Export"). Rename the files in both folders giving them sequential numbers.
2. Import the red and green image series into software such as daime (digital image analysis in microbial ecology)¹⁴. Segment the green channel images with individually chosen brightness thresholds (Segment → Automatic segmentation → Custom threshold). Choose the brightness thresholds with care (typically between 20 and 80), so that all bacteria (brighter than the extracellular matrix), but not the matrix will be recognized as objects during segmentation. Verify visually that the areas recognized as objects correspond well to the bacterial biomass.
3. Transfer the object layer of the segmented green channel images to the corresponding red channel images (Segment → Transfer object layer). Use the object editor function to reject and delete all objects in the red and green channel images. Now only the extracellular matrix is left in the biofilm images. Export the processed image series as TIF files.
4. Import the image series into ImageJ (http://rsb.info.nih.gov/ij; v.1.47). Determine the average fluorescence intensity in the background images taken with the laser turned off (Analyze →  Histogram). Subtract the appropriate background from the red and green images (Process →  Math →  Subtract).
5. Still in ImageJ, divide the green image series (G1) by itself (Process → Image calculator). Then multiply the resulting image series (G2) with the green image series (G1). This will yield an image series (G3), where NaN is assigned to all pixels belonging to areas that were recognized as objects in daime. Proceed in the same way with the red image series (R1/R1 = R2; R2 x R1 = R3).
   Note: As the bacterial biomass was removed from the images in step 4.3, the fluorescent intensity is 0 in these areas. Step 4.5 is necessary to convert the value 0 to NaN, which allows for ratio calculation in step 4.6.
6. Apply the 'Mean' filter (Process → Filters → Mean; radius: 1 pixel) to compensate for detector noise. Divide the green image series by the red image series (Process → Image calculator). This results in a green/red ratio for every remaining pixel in the extracellular space of the images. Use false coloring for graphic representation of the ratios in the images (Image → Lookup Tables). Calculate the mean ratio for each image (Analyze → Histogram).
7. Convert the green/red ratios to pH values according to the function fitted under 1.9.2). Note: An example for calibration data and fitted curve can be seen in Schlafer et al, 2015¹¹.

Wyniki

The presented method allows monitoring extracellular pH drops in different microenvironments of dental biofilms in the pH range from 4.5 to 7 in real-time. If the experimental conditions are chosen as described above, pH starts to drop in all areas of the biofilms shortly after exposure to glucose.

When pH in a biofilm drops, bacterial cells become visible within short time (<1 min), as the ratiometric dye is upconcentrated ...

Dyskusje

Microscopic monitoring of biofilm pH provides several advantages, as compared to electrode or microelectrode measurements^4-6. Microscopic techniques permit to determine pH with a high spatial resolution and allow capturing both horizontal and vertical pH gradients in biofilms without disturbing the biofilm mechanically. Previous attempts of microscopic pH monitoring, however, failed to differentiate between extracellular and intracellular pH in the biofilms^1,7,9. Due to bacterial homeostasis, intrac...

Materiały

Name	Company	Catalog Number	Comments
Zeiss LSM 510 META	Zeiss	N/A
C-Apochromat 63X water immersion objective	Zeiss	N/A
XL Incubator	PeCON	N/A
SNARF-4F 5-(and-6)-Carboxylic Acid	Life Technologies	S23920
Dimethyl sulfoxide	Life Technologies	D12345
HEPES	Life Technologies	11344-041
Costar 96-well black clear-bottom plate	Fisher Scientific	07-200-567
Custom-made glass slabs (4 x 4 x 1 mm3; 1,200 grit)	Menzel	N/A
Alginate impression material	GC Corporation	N/A
Acrylic Adjusting Logic Sets/set of acrylic dental burs	Axis Dental	LS-906
Orthodontic retainer containers	Spark Medical Equipment Co., Ltd	SK-WDTC01
Sticky wax	Dentsply	N/A
Chewing paraffin wax	Ivoclar Vivadent AG	N/A
Dithiothreitol	Sigma Aldrich	D0632	Used during preparation of salivary solution
0.45 µm and 0.2 µm syringe filters	Sigma Aldrich	CLS431220; CLS431219
daime	University of Vienna, Austria	http://dome.csb.univie.ac.at/daime
ImageJ	NIH, Bethesda, Maryland, USA	http://imagej.nih.gov/ij/