Maintenance of a Lateral Fluid Percussion Injury Device

Podsumowanie

Proper care and maintenance are essential for a lateral fluid percussion injury (LFPI) device to function reliably. Here, we demonstrate how to properly clean, fill, and assemble an LFPI device, and ensure that it is adequately maintained for optimal results.

Streszczenie

Traumatic brain injury (TBI) accounts for roughly 2.5 million emergency room visits and hospitalizations annually and is a leading cause of death and disability in children and young adults. TBI is caused by a sudden force applied to the head and, to better understand human TBI and its underlying mechanisms, experimental injury models are necessary. Lateral fluid percussion injury (LFPI) is a commonly used injury model due to similarities in the pathological changes found in human TBI compared to LFPI, including hemorrhages, vascular disruption, neurological deficits, and neuron loss. LFPI employs a pendulum and a fluid-filled cylinder, the latter having a moveable piston at one end, and a Luer lock connection to stiff, fluid-filled tubing at the other end. Preparation of the animal involves performing a craniectomy and attaching a Luer hub over the site. The next day, the tubing from the injury device is connected to the Luer hub on the animal's skull and the pendulum is raised to a specified height and released. The impact of the pendulum with the piston generates a pressure pulse which is transmitted to the intact dura mater of the animal via the tubing and produces the experimental TBI. Proper care and maintenance are essential for the LFPI device to function reliably, as the character and severity of the injury can vary greatly depending on the condition of the device. Here, we demonstrate how to properly clean, fill, and assemble the LFPI device, and ensure that it is adequately maintained for optimal results.

Wprowadzenie

Traumatic brain injury (TBI) is caused by a sudden force applied to the head. Following primary injuries resulting from the physical impact, TBI survivors commonly experience secondary injuries, including cognitive deficits and neurological dysfunctions that are associated with physiological responses to the initial injury¹. It is estimated that roughly 69 million individuals worldwide suffer from TBI annually². In the United States alone, approximately 2.5 million TBI-related emergency room visits and hospitalizations occur each year, making TBI one of the leading causes of disability and death among children and young adults³. TBI can be classified as mild, moderate, or severe, with mild TBI (mTBI) accounting for approximately 70%-90% of TBI cases⁴. Histological and cognitive TBI pathology can occur within minutes to hours of injury, and the effects of TBI can persist for months to years after initial damage⁵.

The development of experimental models has been instrumental in understanding the effects and underlying mechanisms of TBI. One such model, the lateral fluid percussion injury (LFPI), is commonly used to assess TBI in vivo. LFPI closely reproduces pathologies associated with human TBI, including vascular disruptions, hemorrhages, neuronal loss, inflammation, gliosis, and molecular disturbances^6,7,8. The LFPI technique is used for a diverse set of experimental applications, including modeling pediatric TBI, as well as chronic neurodegenerative conditions, such as chronic traumatic encephalopathy^9,10. LFPI is a well-defined and reproducible method of experimental TBI that allows for the severity of the injury to be adjusted¹¹. The LFPI device has several important components, including: a pendulum with a weighted hammer, a piston, a fluid-filled cylinder, a pressure transducer, a digital oscilloscope, and a small tube at the end of the cylinder with a Luer lock which attaches to a hub on the animal's skull (Figure 1). LFPI works by swinging the pendulum into the piston, creating a wave of pressure through the fluid (degassed deionized water or saline) into the brain of the attached animal; this increases intracranial pressure, thus replicating the mechanical features and biological changes of TBI¹². Additionally, animals used in LFPI experiments undergo a craniectomy in order to expose the brain to the impact of the fluid pressure of the device.

Routine maintenance and monitoring are necessary to ensure that the LFPI device is accurately functioning. The following methods are vital in preventing the introduction of contaminating air bubbles into the device. Here, we demonstrate methods to properly clean, fill, and assemble the LFPI device. We will also discuss oscilloscope outputs and mouse righting times as ways to confirm the viability of the LFPI.

Protokół

1. Cleaning the LFPI cylinder

1. Carefully detach the syringes attached to the transducer housing and fill port, as well as the cable connected to the pressure transducer (see Figure 1 for a schematic of injury device components).
2. While being careful not to drop the cylinder, unscrew the hand knobs at the back of the device from the cylinder clamps to free the cylinder.
3. Remove the piston at the end of the cylinder, transducer, transducer housing, and plunger O-rings.
4. Drain fluid out of the cylinder.
5. Add mild detergent, such as dish washing detergent, to the cylinder and scrub lightly using a dish or bottle brush¹³.
6. To ensure that all the detergent is rinsed off, completely fill the cylinder with water and rinse thoroughly.

2. Degassing the fluid used to fill the cylinder

1. Use a vacuum pump to degas the fluid before refilling the cylinder to prevent the formation of new bubbles and absorb existing bubbles.
   NOTE: Approximately 1.5 L of fluid will be needed to fill the cylinder, although degassing approximately 2 L will leave a small supply for replacing any fluid lost during use and testing.
   NOTE: House vacuums are too weak to effectively degas the fluid. The vacuum must be able to produce a pressure of 25-28 inHg.
2. Add a stir bar to the fluid and place the fluid container on a stir plate. Stirring the fluid during the degassing process helps to stimulate bubbling and the release of gas. Stirring also prevents a large sudden increase in bubbling.
   ​NOTE: The degassing process should be over when very few bubbles are being produced; this occurs after roughly 45 min.

3. Reassembly of the LFPI device

1. Apply a thin layer of petroleum jelly to the piston plunger.
2. Attach the piston plunger with the plunger protruding approximately 32 mm from the cylinder¹⁴.
   NOTE: Air frequently gets trapped at the plunger before the leading O-ring. To get rid of this excess air, twist the plunger while moving it in and out to work the air out of this gap.
3. Apply a thin layer of petroleum jelly to the other O-rings as well and attach them to the cylinder, with exception to the O-ring on the fill port.
4. Wrap Teflon tape twice around the transducer's threads.

4. Refilling the LFPI device and attachment to the base

1. Connect a 10 mL syringe filled with degassed fluid and free of air bubbles to the Luer lock hub on the transducer housing.
2. Hold the transducer with the threaded end pointing upward, and completely fill the well inside the threaded region of the transducer with the degassed fluid using a 10 mL syringe. The goal here is to fill the transducer well without introducing any air bubbles. Be careful not to damage the delicate membrane at the bottom of the transducer well.
3. With the cylinder placed at an angle to prevent air from reentering the transducer housing, attach the transducer housing to the cylinder¹³ and use a wrench to tighten it snugly.
4. Remove the cap from the fill port and cylinder once the degassed fluid reaches approximately 2/3 of the cylinder capacity.
5. Place the cylinder horizontally and finish filling the cylinder with degassed fluid.
   NOTE: To avoid the formation of air bubbles, pouring the fluid in slowly is recommended¹⁴.
6. Replace the cap at the fill port and close all stopcocks.
7. Manipulate the cylinder to work any air bubbles to the fill port¹⁴.
8. Open the stopcock on the fill port and inject fluid using the syringe on the transducer housing to force any air bubbles out of the port¹⁴.
9. Inspect the entire device and ensure that there are no air bubbles.
10. Add a 10 mL syringe filled with degassed fluid to the Luer lock hub on the fill cap.
11. Reattach the cylinder to the base using the hand screws.
12. Ensure that the cylinder is horizontal and lined up with the center of the weighted hammer on the pendulum.

Wyniki

We tested the effects of air bubble contamination in an LFPI device on waveform formation. We injected air bubbles into the device and compared the oscilloscope outputs with oscilloscope data collected from a non-contaminated LFPI device. Conditions were as follows: non-contaminated, injection of 5 mL of air, injection of 10 mL of air, and injection of 15 mL of air. We kept the pendulum at a consistent height for all impacts for all conditions, and we performed 15 impacts per condition.

When p...

Dyskusje

The techniques outlined above demonstrate how to properly maintain an LFPI device. Routine cleaning and monitoring are necessary to keep the LFPI device functioning correctly and reliably. Additionally, due to the invasive nature of the LFPI procedure, it is imperative that the device be cleaned thoroughly to prevent infection of laboratory animals.

Avoiding the formation of air bubbles in the device is crucial for obtaining optimal injuries and pressure waveforms. Air bubbles alter the chara...

Materiały

Name	Company	Catalog Number	Comments
2 - 10 mL syringes with Luer lock capability			Ensures that needle is secure and reduces possible leaks of fluid
Degassed fluid			Helps to reduce air bubble formation during injury procedure
Fluid Percussion Injury (FPI) device (Model 01-B)	Custom Designs & Fabrications Inc.	N/A	Injury device used to model TBI in rodents
Mild detergent			Allows to thoroughly clean the LFPI cylinder
Petroleum Jelly			Used as a water-repellent and protects LFPI device form rust
Teflon tape			Helps with tight seal of pipe joints on the LFPI device
*Materials other than the LFPI device can be purchased from any reliable company.