optimization of latin hypercube sampling and adaptive simulated annealing for temperature control in fluid dynamics

Optimizing Battery Heat Management in Dusty Environments

With the rapid development of the automobile industry, traditional fuel vehicles consume a lot of non-renewable resources, resulting in serious environmental pollution and energy shortage. One of the most promising solutions is the development of electric vehicles (EVs)1,2.
The power batteries used for EVs can store electrochemical energy, which is the key to replacing traditional fuel vehicles. Power batteries used in EVs include lithium-ion battery (LIB), nickel-metal hydride battery (NiMH), and electric double-layer capacitor (EDLC)3. Compared to the other batteries, lithium-ion batteries are currently widely used as energy storage units in EVs owing to their advantages such as high energy density, high efficiency, and long life cycle4,5,6,7.
However, due to chemical reaction heat and Joule heat, it is easy to accumulate a large amount of heat and increase the battery temperature during rapid charging and high-intensity discharging. The ideal operating temperature of LIB is 20-40 &#176;C8,9. The maximum temperature difference between the batteries in a battery string should not exceed 5 &#176;C10,11. Otherwise, it may lead to a series of risks such as temperature imbalance between the batteries, accelerated aging, even overheating, fire, explosion, and so on12. Therefore, the critical issue to be resolved is designing and optimizing an efficient battery thermal management system (BTMS) that can control the temperature and temperature difference of the battery pack within a narrow.
Typical BTMS include air cooling, water cooling, and phase change material cooling13. Among these cooling methods, the air cooling type is widely used because of its low cost and simplicity of the structure14. Due to the limited specific heat capacity of air, high temperature and large temperature differences are easy to occur between battery cells in air-cooled systems. In order to improve the cooling performance of air-cooled BTMS, it is necessary to design an efficient system15,16,17. Qian et al.18 collected the battery pack&#39;s maximum temperature and temperature difference to train the corresponding Bayesian neural network model, which is used to optimize cell spacings of the series air-cooled battery pack. Chen et al.19 reported using the Newton method and the flow resistance network model for optimization of the widths of the inlet divergence plenum and the outlet convergence plenum in the Z-type parallel air-cooled system. The results showed a 45% reduction in the temperature difference of the system. Liu et al.20 sampled five groups of the cooling ducts in the J-BTMS and obtained the best combination of cell spacings by the ensemble surrogate-based optimization algorithm. Baveja et al.21 modeled a passively balanced battery module, and the study described the effects of thermal prediction on module-level passive balancing and vice versa. Singh et al.22 investigated a battery thermal management system (BTMS) that used encapsulated phase change material along with forced convective air cooling designed using the coupled electrochemical-thermal modeling. Fan et al.23 proposed a liquid cooling plate comprising a multi-stage Tesla valve configuration to provide a safer temperature range for a prismatic-type lithium-ion battery with high recognition in microfluidic applications. Feng et al. 24 used the coefficient of variation method to evaluate the schemes with different inlet flow rates and battery clearances. Talele et al.25 introduced wall-enhanced pyro lining thermal insulation to store potential generated heating based on optimal placement of heating films.
When one uses air-cooling BTMS, metal dust particles, mineral dust particles, building materials dust particles, and other particles in the external environment will be brought into the air-cooling BTMS by the blower, which can cause the surface of the batteries to be covered with DPM. If there is no heat dissipation plan, it may cause accidents due to the excessively high battery temperature. After simulation, we take the maximum temperature of the battery pack in a specified airflow velocity and dust-free environment as the expected temperature in a dusty environment. First, C-rate refers to the current value required when the battery releases its rated capacity within the specified time, which is equal to a multiple of the battery&#39;s rated capacity in the data value. In this paper, the simulation uses 2C rate discharge. The rated capacity is 10 Ah, and the nominal voltage is 3.2 V. Lithium iron phosphate (LiFePO4) is used as the positive electrode material, and carbon is used as the negative electrode material. The electrolyte has electrolyte lithium salt, a high-purity organic solvent, necessary additives, and other raw materials. The random array representing the different velocity combinations at the inlets was determined through the OLHA, and a 2nd order function between the maximum temperature of the battery pack and the inlet flow velocity combination was set up under the condition of checking the accuracy of the curve fitting. Latin hypercube (LH) designs have been applied in many computer experiments since they were proposed by McKay et al.26. An LH is given by an N x p-matrix L, where each column of L consists of a permutation of the integers 1 to N. In this paper, the optimal Latin hypercube sampling method is used to reduce the computational burden. The method uses stratified sampling to ensure that the sampling points can cover all the sampling internals.
In the following step, the inlet flow velocity combination was optimized to decrease the maximum temperature of the battery pack in a dusty environment based on the ASAM under the condition of considering energy consumption simultaneously. The adaptive simulated annealing algorithm has been extensively developed and widely used in many optimization problems27,28. This algorithm can avoid getting trapped in a local optimum by accepting the worst solution with a certain probability. The global optimum is achieved by defining the acceptance probability and temperature; the calculation speed can also be adjusted by using these two parameters. Finally, for checking the accuracy of the optimization, the optimal result was compared with the analysis result obtained from the simulation software.
In this paper, an optimization method for the inlet flow rate of the battery box is proposed for the battery pack whose temperature rises due to dust cover. The purpose is to reduce the maximum temperature of the dust-covered battery pack to below the maximum temperature of the non-dust-covered battery pack in the case of low energy consumption.

Author Spotlight: Optimization of Airflow Velocities in Battery Cooling Systems for Enhanced Thermal Performance and Reduced Energy Consumption 

Optimization of An Air-Based Heat Management System for Dusty Particulate Matter-Covered Lithium-Ion Battery Packs

Watch this Scientific Journal Video about Optimization of Latin Hypercube Sampling and Adaptive Simulated Annealing for Temperature Control in Fluid Dynamics at JoVE.com

Optimization of Latin Hypercube Sampling and Adaptive Simulated Annealing for Temperature Control in Fluid Dynamics  

optimization-latin-hypercube-sampling-adaptive-simulated-annealing

Research

Education

JoVE Journal

JoVE Core

Civil Engineering

Electrical Engineering

Engineering

Unit 1

Finite Control Volume Analysis

Design of Control Systems

SCIENTISTS IN ACTION

219 Views.  Wenzhou University. Optimization of Latin Hypercube Sampling and Adaptive Simulated Annealing for Temperature Control in Fluid Dynamics

Video: Optimization of Latin Hypercube Sampling and Adaptive Simulated Annealing for Temperature Control in Fluid Dynamics  