The authors would like to acknowledge the Humic Products Trade Association (HPTA) for their support in funding the work that resulted in the standardization of the methods described in this paper and also Lawrence Mayhew and Drs. Dan Olk and Paul Bloom for technical support during the standardization work.

1. Solid sample preparation
<ol>
	<li>Crush approximately 5 g of the sample to be analyzed, using a mortar and pestle, so that 100% of the crushed sample passes through a U. S. Standard Sieve mesh size No. 200 (i.e., 74 &#181;m) making sure that the powder is well mixed.</li>
	<li>Determine the moisture content of the powder gravimetrically.
	<ol>
		<li>Weigh an aluminum weigh boat and record the mass (Wwb).</li>
		<li>Transfer approximately 2 g of sample powder into the weigh boat and record the mass (Wws+wb).</li>
		<li>Place the weigh boat in a drying oven for 24 h at 102 &#176;C (do not exceed 102 &#176;C). After 24 h, remove the weigh boat from drying oven and place in a desiccator to cool for at least 1 h.</li>
		<li>Weigh and record the mass of the weigh boat and dried sample powder (Wds+wb).</li>
		<li>Determine the moisture content using formula 1.1. 
		Formula 1.1 Moisture content of solid sample powder 
		&#8203;% moisture = (((Wws+wb- Wwb) &#8211; (Wds+wb - Wwb))/ (Wws+wb - Wwb)) * 100</li>
	</ol>
	</li>
</ol>
2. Extraction procedure
<ol>
	<li>Solid samples
	<ol>
		<li>Weigh approximately 2.5 g of the sieved&#160;sample powder (Wsamp) into a plastic or aluminum weigh boat and record the weight to four decimal places.</li>
		<li>Load the sample into a 1 L graduated cylinder and fill the cylinder to 1 L with 0.1 M NaOH (4 g NaOH x L-1).</li>
		<li>Add a magnetic stir bar (e.g., 5 - 7 cm in length) and stir rapidly (i.e., 300 &#8211; 400 rpm) on a stir plate until the sample is thoroughly mixed.</li>
		<li>Transfer the entire contents of the graduated cylinder into a 1 L Erlenmeyer flask, evacuate the headspace of the flask with N2 gas and cover the flask opening with an airtight cover.</li>
		<li>Place the Erlenmeyer flask on a stir plate and mix at 300 - 400 rpm for 16 - 18 h.</li>
	</ol>
	</li>
	<li>Liquid samples
	<ol>
		<li>For liquid materials, thoroughly mix the sample by shaking to ensure that the test liquid is mixed homogeneously. Make sure any residue that may have fallen to the bottom of the container is thoroughly mixed.</li>
		<li>Add approximately 5 g of the test liquid, weighed to 4 decimal places (WTL), to a 1 L graduated cylinder.</li>
		<li>Fill the graduated cylinder with 0.1 M NaOH to a final volume of 1 L.</li>
		<li>Add a magnetic stir bar (e.g., 5 &#8211; 7 cm in length) and stir rapidly (e.g., 300 - 400 rpm) on a stir plate until the test sample is completely mixed.</li>
		<li>Transfer the mixture into a 1 L Erlenmeyer flask, evacuate the headspace with N2 gas and cover the flask opening with an airtight cover.</li>
		<li>Place the Erlenmeyer flask on a stir plate and mix at 300 - 400 rpm for 1 h. 
		NOTE: After this point, the handling of solid and liquid samples is the same.</li>
	</ol>
	</li>
</ol>
3. Removal of nonsoluble materials from alkaline extracts
<ol>
	<li>At the completion of stirring, remove the flask from the stir plate, transfer the mixture to suitable centrifuge tubes and centrifuge the entire volume at 4,921 x g for 30 min.</li>
	<li>Collect the alkaline supernatant containing the HA and FA in a clean 1 L Erlenmeyer flask containing a magnetic stir bar. Discard the insoluble material. Filtration through glass wool or qualitative 2.5 &#181;m pore size filter paper is recommended if residual particles are not precipitated after centrifugation.</li>
</ol>
4. Precipitation and separation of HA from FF
<ol>
	<li>While stirring the alkaline extract at 300 - 400 rpm on a stir plate, insert a pH probe into the middle portion of the solution (vertically) and add conc. HCl dropwise to the alkaline extract until a stable pH of pH 1.0 &#177; 0.1 is reached.</li>
	<li>Once a pH of pH 1 is reached and remains stable, remove the pH probe from the flask, retrieve the stir bar, cover the flask with an airtight cover and let the flask sit until the precipitated HA has settled to the bottom of the flask. 
	NOTE: The time it takes a HA to precipitate and drop out of solution will vary depending on the source and amount of HA in the sample. It typically takes 1 -6 h for the HA to fully precipitate and drop out of solution.</li>
	<li>Centrifuge the extract and precipitated HA at 4921 x g for 1 h. After centrifugation, pour off the supernatant FF into a clean 1 L Erlenmeyer and cover with an airtight cover. 
	NOTE: A longer centrifuge time may be necessary in order to pack the HA down firmly enough to allow decanting the FF without inclusion of any of the precipitated HA.</li>
	<li>Place the centrifuge tubes in a drying oven held at 100 &#176;C for 24 h.</li>
	<li>After drying, remove the tubes from the drying oven and place in a desiccator to cool to room temperature. After cooling, quantitatively transfer the residue from the tube by scraping it from the sides and bottom of the tube with a spatula, transfer to a tared weigh boat, and record the mass (WEHA). This residue is the &#8220;Extracted HA&#8221;. 
	NOTE: If centrifuge tubes greater than 50 mL have been used in the separation of HA and FF, it is convenient to transfer the precipitated HA to temperature resistant 50 mL centrifuge tubes for the drying process. Also, if a freeze dryer is available the precipitated HA can be freeze dried. Collection of the HA in a freeze-dried state is easier because the HA does not stick to the side of the plastic tubes and does not have to be scrapped.</li>
</ol>
5. Determination of ash content
NOTE: The procedure for determination of ash content of dried HA and FA samples is the same. The procedure using notation for HA is shown.
<ol>
	<li>Transfer approximately 30 mg of the dried HA (WHA) to a clean, pre-weighed ceramic dish (WCD) that had been previously dried in a drying oven at 100 &#176;C and then cooled in a desiccator to room temperature. After recording the combined mass of the weighted HA and dish (WHA+CD), combust the HA in a muffle oven for 2 h at 600&#176;C. 
	NOTE: For each HA sample, three replicates should be processed and the average ash content used in the calculation of pure HA.</li>
	<li>After 2 h, remove the dish and contents from the muffle oven and place in a desiccator to cool. Once cool, weigh the dish with ash (WASH+CD) and calculate the ash ratio (Ashrat) using formula 1.2: 
	Formula 1.2 Ashrat = (WASH+CD - WCD) / (WHA+CD - WCD)</li>
</ol>
6. Determination of the percentage of purified extracted HA
<ol>
	<li>Determine the final mass of the pure HA (WPHA) by correcting for ash content using Formula 1.3: 
	Formula 1.3 WPHA = WEHA * (1- Ashrat)</li>
</ol>
7. Determination of the concentration (%) of pure HA in the original source sample
<ol>
	<li>Determine the concentration of pure HA using Formula 1.4 and 1.5: 
	Formula 1.4: % pure HA in solid sample = (WPHA/Wsamp) * 100 
	Formula 1.5: % pure HA in liquid sample = (WPHA/WTL) * 100</li>
</ol>
8. Column preparation for HFA purification
<ol>
	<li>Prepare a low-pressure chromatography column packed with polymethylmethacrylate DAX-8 resin. If the resin has not been used previously, soak the resin in methanol for 2 h and then rinse thoroughly with deionized H2O until all the methanol is removed.
	<ol>
		<li>Remove small resin particles that float on the water at this time. If the resin has been used previously, regenerate it as described in section 10.</li>
	</ol>
	</li>
	<li>Once thoroughly rinsed, pour the resin into a 5 x 25 cm glass chromatography column fitted with an end piece with a 10 &#181;m frit for resin bed support. Leave 2.5 to 5 cm at top of column for resin-free solution to enable mixing of the FF prior to entering the resin bed. Fit the top piece to the column and pump deionized H2O through the top of the column to pack the DAX-8 resin bed by using a peristaltic pump.</li>
</ol>
9. Isolation of HFA
<ol>
	<li>Once the resin bed is packed, load the FF onto the column using a peristaltic pump, under low pressure, via the top of the column. Use a flow rate of 35 &#8211; 40 mL/min. It is critical that the top of the resin in the column remains covered with solution throughout the entire loading and rinsing procedure to prevent drying of the resin and channeling of the extract though the resin bed.</li>
	<li>Once the fulvic fraction has been completely loaded onto the resin, wash the resin with deionized water, to remove the non-adsorbed &#8220;hydrophilic fulvic fraction&#8221; (HyFF) by pumping it through the top of the column using the peristaltic pump under low pressure. Use a flow rate of 35 &#8211; 40 mL/min. Discard the HyFF-containing effluent unless it will be used for analysis.</li>
	<li>Wash the column with deionized H2O until the absorbance at 350 nm of the column effluent is equal (e.g., within 0.015 absorbance units) to that of the deionized H2O used to wash the column. Use deionized water to zero (i.e., blank) the spectrophotometer.</li>
	<li>Desorb the HFA by back elution by pumping 0.1 M NaOH via the bottom of the column using the peristaltic pump. Use a flow rate of 35 &#8211; 40 mL/min. Capture the pump effluent (the Na-fulvate in a clean sufficiently sized container (e.g., 2 L Erlenmeyer). 
	NOTE: Most of the HFA adsorbs to the very top of the DAX-8 resin bed. Desorption by introducing the 0.1 M NaOH from the bottom of the column minimizes the amount of 0.1 M NaOH needed to fully desorb the FA.</li>
	<li>All the HFA has been desorbed when the absorbance of the column effluent is equal to the absorbance of 0.1 M NaOH influent at 350 nm. Use 0.1 M NaOH as the spectrophotometric blank. Add the effluent taken to check absorbance of the desorbed FA solution to ensure all FA is captured.</li>
</ol>
10.&#160;HFA de-ashing by protonation
<ol>
	<li>Pass the Na-fulvate solution, repeatedly, by gravity feed, through strong cation H+- exchange resin (Table of Materials) contained in a 5 &#215; 50 cm column, with glass frit to retain the resin, until the electrical conductivity of the effluent is &#60;120 &#181;S/cm, as measured with an electrical conductivity meter. Prior to each pass, the H+-exchange resin requires refurbishment as described in Section 11.
	<ol>
		<li>To ensure that all the FA is removed from the resin after the final pass, wash the resin with deionized water until the absorbance of effluent at 350 nm is the same (e.g., within 0.015 absorbance units) as the deionized water used to wash the column. Use deionized H2O as the spectrophotometric blank. Add the wash and any effluent portions taken to check absorbance to the purified FA solution. To help with removal of all FA, the resin can be agitated (e.g., using a long glass or plastic rod) several times.</li>
	</ol>
	</li>
	<li>Concentrate the FA to a volume of approximately 15 &#177; 2 mL by using a rotary evaporator at 55 &#176;C.</li>
	<li>Completely transfer the 15 mL FA concentrate to a 50 mL plastic centrifuge tube and dry at 60&#177;3 &#176;C to constant dryness in a drying oven. Freeze-drying is an alternative to oven drying. After drying transfer the tube to a desiccator to cool.
	<ol>
		<li>Remove FA from the tube by scraping the tube sides and bottom with a spatula and weigh the collected FA on pre-tared weigh paper. This material is the &#8220;Extracted FA&#8221; (WEFA).</li>
		<li>Determine the ash ratio (ASHrat) of extracted FA as described under Step 6 for HA and calculate the ash ratio using Formula 1.2. Determine the weight of the extracted FA without ash (WPFA) using Formula 1.3, substituting the WEFA for weight of WEHA. Finally determine the % pure FA in the sample using Formula 1.4 substituting WPFA for WPHA.</li>
	</ol>
	</li>
</ol>
11. DAX-8 resin regeneration
<ol>
	<li>Regenerate the DAX-8 resin by pumping 0.1 M HCl (8.33 mL concentrated HCl/1000 mL final volume deionized H2O) at a flow rate of 35 &#8211; 40 mL/min through the bottom of the column until the pH of the effluent is equal to the pH of the influent. Use the peristaltic pump to pump all reagents through the DAX-8 column during regeneration.</li>
	<li>Rinse the column with DI water by pumping it into the top of the column until the pH of the effluent equals the pH of the influent (i.e., DI water).</li>
</ol>
12. H+-cation exchange resin regeneration
<ol>
	<li>Regenerate the H+ cation exchange resin in a batch process by pouring the resin into a large beaker (e.g., 4 L plastic beaker), rinse several times by covering the resin with DI H2O, mixing and then pouring off the water.</li>
	<li>Cover the resin with 1 M HCl (83.3 mL concentrated HCl/1000 mL final volume DI water). Let stand for a minimum of 2 h with occasional stirring (e.g., once every 30 min).</li>
	<li>Remove the excess acid from the resin by pouring off the acid and covering the resin with DI water. Stir vigorously with a stirring rod for 15 s, then let the resin drop to the bottom of the flask and then pour off the water. Repeat the process until the electrical conductivity of the rinse water is &#8804; 0.7 &#181;S/cm.</li>
	<li>Load the regenerated resin back into the column. Cover with deionized H2O to make sure the resin remains wet between uses.</li>
</ol>

<ol>
	<li>DiDonato, N., Chen, H., Waggoner, D., Hatcher, P. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Potential+origin+and+formation+for+molecular+components+of+humic+acids+in+soils.">Potential origin and formation for molecular components of humic acids in soils.</a> Geochimica et Cosmochimica Acta. 178, 210-222 (2016).</li><li>Waggoner, D. C., Chen, H., Willoughby, A. S., Hatcher, P. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Formation+of+black+carbon-like+and+alicyclic+aliphatic+compounds+by+hydroxyl+radical+initiated+degradation+of+lignin.">Formation of black carbon-like and alicyclic aliphatic compounds by hydroxyl radical initiated degradation of lignin.</a> Organic Geochemistry. 82, 69-76 (2015).</li><li>Baldock, J. A., Skjemstad, J. O. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Role+of+the+soil+matrix+and+minerals+in+protecting+natural+organic+materials+against+biological+attack.">Role of the soil matrix and minerals in protecting natural organic materials against biological attack.</a> Organic Geochemistry. 31 (7-8), 697-710 (2015).</li><li>Kallenbach, C. M., Frey, S. D., Grandy, A. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Direct+evidence+for+microbial-derived+soil+organic+matter+formation+and+its+ecophysiological+controls.">Direct evidence for microbial-derived soil organic matter formation and its ecophysiological controls.</a> Nature Communications. 7, 13630 (2016).</li><li>Schaeffer, A., Nannipieri, P., Kastner, M., Schmidt, B., Botterweck, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=From+humic+substances+to+soil+organic+matter-microbial+contributions.+In+honour+of+Konrad+Haider+and+James+P.+Martin+for+their+outstanding+research+contributionns+to+soil+science.">From humic substances to soil organic matter-microbial contributions. In honour of Konrad Haider and James P. Martin for their outstanding research contributionns to soil science.</a> Journal of Soils Sediments. 15 (9), 1865-1881 (2015).</li><li>Stevenson, F. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Humus Chemistry: Genesis, Composition, Reactions. 2e. , (1994).</li><li>Weber, J., Chen, Y., Jamroz, E., Miano, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Preface:+humic+substances+in+the+environment.">Preface: humic substances in the environment.</a> Journal of Soils and Sediments. 18, 2665-2667 (2018).</li><li>Schnitzer, M., Page, A. L., Miller, R. H., Keeny, D. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Organic+matter+characterization.">Organic matter characterization.</a> Methods of soil analysis, part 2: Chemical and microbiological properties. , 581-594 (1982).</li><li>Mehlich, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Photometric+determination+of+humic+matter+in+soils:+A+proposed+method.">Photometric determination of humic matter in soils: A proposed method.</a> Communications in Soil Science and Plant Analysis. 15 (12), 1417-1422 (1984).</li><li>Lamar, R. T., Talbot, K. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Critical+comparison+of+humid+acid+test+methods.">Critical comparison of humid acid test methods.</a> Communications in Soil Science and Plant Analysis. 50 (15-16), 2309-2322 (2009).</li><li>Swift, R. S., Sparks, D. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Organic+matter+characterization.">Organic matter characterization.</a> Methods of soil analysis, part 3: Chemical methods. , 1011-1069 (1996).</li><li>Lamar, R. T., Olk, D. C., Mayhew, L., Bloom, P. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+new+standardized+method+for+quantitation+of+humic+and+fulvic+acids+in+humic+ores+and+commercial+products.">A new standardized method for quantitation of humic and fulvic acids in humic ores and commercial products.</a> Journal of the AOAC International. 97 (3), 722-731 (2014).</li><li>International Organization of Standards. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Fertilizers+and+soil+conditioners-Determination+of+humic+and+hydrophobic+fulvic+acids+concentrations+in+fertilizer+materials.">Fertilizers and soil conditioners-Determination of humic and hydrophobic fulvic acids concentrations in fertilizer materials.</a> International Organization of Standards. , (1982).</li><li>Liam, L. E., Serben, T., Cano, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Gravimetric+quantification+of+hydrophobic+filmic+acids+in+lignite+material+using+acetone.">Gravimetric quantification of hydrophobic filmic acids in lignite material using acetone.</a> Journal of the AOAC International. 102 (6), 1901-1907 (2019).</li><li>House, W. A., Zhmud, B. V., Orr, D. R., Lloyd, G. K., Irons, G. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Transportation+of+pesticides+by+colloids.+Final+Report.">Transportation of pesticides by colloids. Final Report.</a> Institute of Freshwater Ecology. National Environment Research Council. , (1998).</li></ol>

The authors have no conflicts of interest to declare.

The initial steps of extraction and isolation of the HA in this method are relatively straightforward. Because the isolation of the HFA involves column chromatography, obtaining repeatable results comes with strict adherence to the details of each step and practice. In particular, correct preparation of the resins is of primary importance. It is extremely important that the polymethylmethacrylate DAX-8 resin is prepared and packed properly. Correct packing of the resin affects both the yield and quality of the HFA. If channeling exists, then neither pretreatment (i.e. acidification) or adsorption of HFA will be complete, and the separation will lead to inaccurate results. If channels or spaces in the resin are observed prior to sample loading the column should be removed and shaken to redistribute the resin beads, by allowing them to settle without channels, and then re-packed by pumping clean DI H2O through the resin. In addition, as mentioned in the protocol, maintaining a volume of liquid above the resin when loading the FF onto the resin, will allow the FF to mix prior to entering the resin and result in more effective adsorption. For the strong cation H+-exchange resin (Table of Materials), complete regeneration cannot be rushed. The Na+/H+ exchange takes time and therefore this is best done in a bulk treatment so that the resin can be mixed while being re-acidified. Mixing the resin while rinsing with DI H2O helps remove the excess HCl. When rising the acidified resin to remove excess acid, mixing the resin help removing the HCl. It is extremely important to remove the acid to the point where an electrical conductivity of &#8804; 0.7 &#181;S/cm is reached. If not, the HCl will be carried over with the HFA.
Finally, when desorbing the HFA from the DAX-8 resin, once the absorbance of the influent equals the absorbance of the effluent, it is a good practice to let the column sit for a couple hours to see if any additional HFA will be released. If so, it will be seen as a yellowing of the liquid above the resin. If this occurs, the additional HFA can be removed by continued desorption until influent/effluent absorbances are equal again.
One of the disadvantages of the HFA isolation is that the entire process is time consuming. The complete desorption of HFA from the DAX-8 resin and complete removal from the H+-exchange resin both result in a significant volume of HFA that has to be reduced by rotary evaporation. This is definitely a bottleneck in the analysis. In an effort to reduce this time, desorbing the HFA from the DAX-8 resin using acetone rather than 0.1 M NaOH has been suggested14. The authors claimed that by using 50% acetone as desorbent in place of NaOH, a similar HFA result was obtained and the DAX-8 was adequately regenerated and thus the H+-exchange step could be eliminated. This modification resulted in a greatly reduced analysis time as a result of decreased volume produced and quicker rotary evaporation&#160;of acetone compared to water. This modification deservers further study.
This method is limited to the analysis of organic matter that has undergone the process of humification, and for the case of peat and soft coals, the further processes of peatification and both peatification and coalification, respectively. Humification is the process whereby dead, primarily plant material, is decomposed by a sequence of microbes that consume and modify increasingly recalcitrant substrates. Abiotic processes also participate in decomposition and re-synthesis reactions. Humification ultimately results in the production of relatively recalcitrant materials comprising heterogeneous mixtures of thousands of molecules that form a range of molecular weight and carbon, oxygen and hydrogen contents that form HS. HS are further modified by peatification and coalification. Therefore, this method is not appropriate for plants materials that have been modified by chemical processes. For example, lignosulfonate is widely used as an HFA adulterant. Lignosulfonate is a by-product of the sulfite pulping process. Therefore, this material has not been produced by the process of humification. In addition, there are many substances that bind to the DAX-8 resin. For example, DAX-8 resin has been used to adsorb pesticides from solution15. Obviously, pesticides are not HS. Thus, binding of a material to DAX-8 resin does not justify a claim that it is an HFA. The prerequisites are both production by humification and binding to DAX-8 resin.
As more is learned about the contribution of the various components of HS in different applications, it may become advantageous to further fractionate HS and thus modify the method accordingly. As it exists, the method does not quantify the HYFA. However, this fraction might also have activity e.g. in plant biostimulation, where the whole FF is generally applied in agricultural treatments rather than purified HFA.

Humic substances (HS) are dynamic residues that result from the microbial decomposition and transformation of dead plant tissues1,2,3 augmented with microbial by-products and biomass3,4,5 through a process that is termed humification6. HS are present in soils, natural waters, lake sediments, peats, soft coals and humic shales and represent an estimated 25% of total organic carbon on the earth7. These substances are complex mixtures of thousands of unique molecules that are fractionated into three main fractions based on their different solubilities in strongly basic and acid aqueous solutions. These fractions are humic acids (HAs), which comprise the alkali-soluble but acid-insoluble fraction; fulvic acids (FAs), the fraction soluble in both alkali and acid; and the humin fraction, which is insoluble at all pH values6,8. The fulvic fraction (FF) is further subdivided into the hydrophobic FA (HFA) and hydrophilic (HyFA) fractions. These fractions are defined as the part of the FF that binds to a hydrophobic DAX-8 resin (HFA) and the part that does not bind to the resin (HyFA).
HS are increasingly being used in agriculture, where they are widely used as crop biostimulants, in animal husbandry, in particular as a livestock feed additive, in mining in drilling muds, and environmental remediation as electron shuttles. Research in the use of HS in human medical applications is also increasing.
Many methods for the quantitation of HA and FA exist. However, most of these methods are neither accurate nor precise. For example, the two most widely used methods for the determination of HA in the USA are the colorimetric method9 and the California Department of Food and Agriculture (CDFA) method, both of which were shown to overestimate the amount of HA in a range of ore and extract sources from the western US and Canada10.The colorimetric or spectrophotometric method is inaccurate because it relies on the absorbance of alkaline extracts that include, in addition to HA, FA and other chromophores that all absorb at the wavelength used and the standard is not representative of the materials being tested10.The CDFA method is not accurate because it does not provide HA concentrations on an ash-free basis. Because different ores have different amounts of ash, some of which is carried with the extraction and the extraction process itself adds ash, this method does not provide an accurate value for HA concentrations10. In response to the need for an accurate and precise method, a standardized gravimetric procedure based on the one detailed by11 was published in 2014 to address quantitation of both HA and FA on an ash free basis12. This method was then adapted, with minor modifications, by the International Organization for Standardization (ISO) in 2018 under Fertilizers and soil conditioners as &#8220;Determination of humic and hydrophobic fulvic acids concentrations in fertilizer materials&#8221;13.
This paper outlines the protocol for extraction and quantitation of humic and hydrophobic fulvic acids and gives details on the accuracy and precision of the data produced from the method.

<table><tbody><tr><td>Amberlite IR 120 H&lt;sup&gt;+&lt;/sup&gt;-exchange resin</td><td>Sigma-Aldrich</td><td>10322</td><td>H&lt;sup&gt;+ &lt;/sup&gt;form</td></tr><tr><td>Analytical Balance</td><td>Ohaus</td><td>PA214</td><td>w/ glass draft shield</td></tr><tr><td>Centrifuge</td><td>Beckman Coulter</td><td>Allegra X-14</td><td>minimum 4300 rpm</td></tr><tr><td>Centrifuge tubes</td><td>Beckman Coulter</td><td></td><td>To fit rotor selected</td></tr><tr><td>Ceramic Combustion Crucibles</td><td>Sigma</td><td>Z247103</td><td></td></tr><tr><td>Chromatography column for DAX-8</td><td>Diba</td><td>Omnifit 006EZ-50-25-FF</td><td></td></tr><tr><td>Chromatography column for IR 120</td><td>Chemglass</td><td>CG-1187-21 2 in. by 24 in.</td><td></td></tr><tr><td>Dessicator</td><td>Capitol Scientic</td><td>Kimax 21200-250</td><td>Vacuum type</td></tr><tr><td>Drying Oven</td><td>Fisher Scientific</td><td>Isotemp</td><td>Precision&amp;plusmn;3?C</td></tr><tr><td>Electrical conductivity meter</td><td>HM Digital</td><td>EC-3</td><td></td></tr><tr><td>Erlenmeyer Flasks</td><td>Amazon</td><td></td><td>1L, 2L</td></tr><tr><td>HCl concentrated</td><td>Sigma-Aldrich</td><td>320331</td><td></td></tr><tr><td>Magnetic Stir Plate</td><td>Barnstead-Thermolyne</td><td>Dataplate 721</td><td></td></tr><tr><td>Magnetic Stir bars</td><td></td><td></td><td>These can be obtained at many outlets</td></tr><tr><td>Muffle Furnace</td><td>Fisher scientific</td><td>Thermolyne Type 47900</td><td></td></tr><tr><td>NaOH</td><td>Sigma-Aldrich</td><td>795429</td><td></td></tr><tr><td>Nitrogen gas</td><td>Praxair</td><td>UNI1066</td><td>99.99% purity</td></tr><tr><td>Peristaltic pump</td><td>Cole Parmer</td><td>Masterflex 7518-00</td><td></td></tr><tr><td>Perstaltic tubing</td><td>Cole Parmer</td><td>Masterflex Pharmed 06508-17</td><td></td></tr><tr><td>pH meter</td><td>Oakton Instruments</td><td>WD-35618--03</td><td></td></tr><tr><td>Rotary Evaporator</td><td>Buchi</td><td>R-210/R-215</td><td></td></tr><tr><td>Spectrophotometer</td><td>Healthcare SCiences</td><td>Ultrospec II</td><td>Dual beam 200 to 900 nm with wavelength accuracy of &amp;plusmn;1 nm and reproducibility of &amp;plusmn;0.5 nm.</td></tr></tbody></table>

quantification of humic and fulvic acids in humate ores, doc, humified materials and humic substance-containing commercial products

The purpose of this method is to provide an accurate and precise concentration of humic (HA) and/or fulvic acids (FA) in soft coals, humic ores and shales, peats, composts and humic substance-containing commercial products. The method is based on the alkaline extraction of test materials, using 0.1 N NaOH as an extractant, and separation of the alkaline soluble humic substances (HS) from nonsoluble products by centrifugation. The pH of the centrifuged alkaline extract is then adjusted to pH 1 with conc. HCl, which results in precipitation of the HA. The precipitated HA are separated from the fulvic fraction (FF) (the fraction of HS that remains in solution,) by centrifugation. The HA is then oven or freeze dried and the ash content of the dried HA determined. The weight of the pure (i.e., ash-free) HA is then divided by the weight of the sample and the resulting fraction multiplied by 100 to determine the % HA in the sample. To determine the FA content, the FF is loaded onto a hydrophobic DAX-8 resin, which adsorbs the FA fraction also referred to as the hydrophobic fulvic acid (HFA). The remaining non-fulvic acid fraction, also called the hydrophilic fulvic fraction (HyFF) is then removed by washing the resin with deionized H2O until all nonabsorbed material is completely removed. The FA is then desorbed with 0.1 N NaOH. The resulting Na-fulvate is then protonated by passing it over a strong H+-exchange resin. The resulting FA is oven or freeze dried, the ash content determined and the concentration in the sample calculated as described above for HA.

Performance data for the method are provided in Tables 1 &#8211; 5. The precision of method for extraction of HA and FAH from liquid commercial samples with very different concentrations of HA and FHA are given in Table 1.
The relative standard deviations (RSDs) for HA were lower than those for HFA, but the average HFA RSD over the three liquid samples was on 6.83% which indicates a high degree of precision. The Horwitz ratio (HorRat) is a normalized performance parameter that indicates the suitability of a methods of analysis regarding among laboratory precision. Here it was used for intra-laboratory precision. Value &#60; 0.5 may indicate undisclosed averaging or a high level of experience with the method. Values &#62; 2.0 indicate heterogeneity of test samples, a need for method optimization or more extensive training, operating below the limit of detection or an inapplicable method. For analysis of liquid samples, the HorRat was only &#62; 2 for one of the HFA analyses (Table 1).
Precision data for the extraction of HA and HFA from three humic ore samples is given in Table 2. Again, with the exception of the HFA extracted from Ore 2 and the HA from Ore 3, all of the HorRat&#8217;s were below 2. This demonstrates a high degree of precision of this method for extraction of HA and HFA for humic ore samples.
Manufacturers of plant biostimulants often formulate products that contain HS in addition to other ingredients like seaweed, inorganic fertilizers, coals or molasses. Table 3 gives the results of an analysis of the inclusion of these types of additives on the precision of the method. None of the additives effected the recovery of HA or HFA significantly (Table 3).
Table 4 and Table 5 report the recoveries of HA and HFA, respectively, from liquid samples that simulated commercial products with very low concentrations. Recoveries were excellent and ranged between 88% and 97% for HA (Table 4) and 92% and 104% for HFA (Table 5). Mean recoveries for HA and HFA were 93% and 97%, respectively and % RSD for both HS were less than 5%. While precision is excellent, these data indicate the need to perform laboratory replicates. The method detection limit (MDL) and method quantitation limit were 4.62 and 1.47 mg/L for HA and 4.8 and 1.53 mg/L for HFA.
<table border="1" fo:keep-together.within-page="1">
	<tbody>
		<tr>
			<td colspan="8">Humic substances, %</td>
		</tr>
		<tr>
			<td>Material</td>
			<td colspan="2">L16</td>
			<td colspan="2">L17</td>
			<td colspan="3">L2</td>
		</tr>
		<tr>
			<td></td>
			<td>HFA</td>
			<td>HA</td>
			<td>HFA</td>
			<td>HA</td>
			<td>HFA</td>
			<td>HA</td>
			<td></td>
		</tr>
		<tr>
			<td>Rep 1</td>
			<td>1.44</td>
			<td>17</td>
			<td>6.59</td>
			<td>7.76</td>
			<td>0.36</td>
			<td colspan="2">4.46</td>
		</tr>
		<tr>
			<td>Rep 2</td>
			<td>1.39</td>
			<td>16.03</td>
			<td>6.25</td>
			<td>7.79</td>
			<td>0.42</td>
			<td colspan="2">4.93</td>
		</tr>
		<tr>
			<td>Rep 3</td>
			<td>1.34</td>
			<td>16.44</td>
			<td>6.02</td>
			<td>7.55</td>
			<td>0.4</td>
			<td colspan="2">4.46</td>
		</tr>
		<tr>
			<td>Rep 4</td>
			<td>1.54</td>
			<td>16.75</td>
			<td>6.2</td>
			<td>7.69</td>
			<td>0.33</td>
			<td colspan="2">4.53</td>
		</tr>
		<tr>
			<td>Mean</td>
			<td>1.43</td>
			<td>16.56</td>
			<td>6.27</td>
			<td>7.7</td>
			<td>0.38</td>
			<td colspan="2">4.6</td>
		</tr>
		<tr>
			<td rowspan="2">SD</td>
			<td rowspan="2">0.09</td>
			<td rowspan="2">0.42</td>
			<td>0</td>
			<td rowspan="2">0.11</td>
			<td rowspan="2">0.04</td>
			<td colspan="2" rowspan="2">0.23</td>
		</tr>
		<tr>
			<td>24</td>
		</tr>
		<tr>
			<td>RSD, %</td>
			<td>6.29</td>
			<td>2.53</td>
			<td>3.8</td>
			<td>1.39</td>
			<td>10.4</td>
			<td colspan="2">4.91</td>
		</tr>
		<tr>
			<td>Hor Rat(r)</td>
			<td>1.58</td>
			<td>0.72</td>
			<td>1.25</td>
			<td>0.47</td>
			<td>2.31</td>
			<td colspan="2">1.55</td>
		</tr>
		<tr>
			<td colspan="8">aExtraction conditions were 1 g in 1 L 0.1 M NaOH.</td>
		</tr>
	</tbody>
</table>
Table 1. Precision of the method in extraction and quantitation of HA and HFA from liquid commercial samples. Extraction conditions were 1 g in 1 L 0.1 M NaOH.
<table border="1" fo:keep-together.within-page="1">
	<tbody>
		<tr>
			<td colspan="7">Humic substances, %</td>
		</tr>
		<tr>
			<td></td>
			<td colspan="2">Ore 1</td>
			<td colspan="2">Ore 2</td>
			<td colspan="2">Ore 3</td>
		</tr>
		<tr>
			<td>Material</td>
			<td>HFA</td>
			<td>HA</td>
			<td>HFA</td>
			<td>HA</td>
			<td>HFA</td>
			<td>HA</td>
		</tr>
		<tr>
			<td>Rep 1</td>
			<td>1.75</td>
			<td>67.4</td>
			<td>1.31</td>
			<td>27.01</td>
			<td>1.55</td>
			<td>8.95</td>
		</tr>
		<tr>
			<td>Rep 2</td>
			<td>1.69</td>
			<td>67.63</td>
			<td>1.25</td>
			<td>27.48</td>
			<td>1.41</td>
			<td>7.2</td>
		</tr>
		<tr>
			<td>Rep 3</td>
			<td>1.63</td>
			<td>67.1</td>
			<td>1.27</td>
			<td>27.34</td>
			<td>1.47</td>
			<td>8.35</td>
		</tr>
		<tr>
			<td>Rep 4</td>
			<td>1.77</td>
			<td>67.59</td>
			<td>1.55</td>
			<td>26.89</td>
			<td>1.51</td>
			<td>7.98</td>
		</tr>
		<tr>
			<td>Mean</td>
			<td>1.71</td>
			<td>67.53</td>
			<td>1.35</td>
			<td>27.18</td>
			<td>1.49</td>
			<td>8.12</td>
		</tr>
		<tr>
			<td>SD</td>
			<td>0.06</td>
			<td>0.94</td>
			<td>0.14</td>
			<td>0.28</td>
			<td>0.06</td>
			<td>0.73</td>
		</tr>
		<tr>
			<td>RSD, %</td>
			<td>3.7</td>
			<td>1.39</td>
			<td>10.33</td>
			<td>1.02</td>
			<td>4.02</td>
			<td>9.02</td>
		</tr>
		<tr>
			<td>HorRat(r)</td>
			<td>0.99</td>
			<td>0.66</td>
			<td>2.71</td>
			<td>0.42</td>
			<td>1.07</td>
			<td>3.09</td>
		</tr>
	</tbody>
</table>
Table 2. Precision of the method in extraction and quantitation of HA and HFA from humic ores. Extraction conditions were 1 g sample in 1 L 0.1 M NaOH. (Data taken from Lamar et al., 2014)
<table border="1" fo:keep-together.within-page="1">
	<tbody>
		<tr>
			<td>Replicate</td>
			<td>Adulterant</td>
			<td>HA, %</td>
			<td>FA, %</td>
			<td>Relative Recovery HA, %</td>
			<td>Relative Recovery HFA, %</td>
		</tr>
		<tr>
			<td>1</td>
			<td>None</td>
			<td>81.61</td>
			<td>12.86</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>2</td>
			<td>None</td>
			<td>80.16</td>
			<td>12.78</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>1</td>
			<td>Seaweed</td>
			<td>80.21</td>
			<td>12.85</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>2</td>
			<td>Seaweed</td>
			<td>80.72</td>
			<td>12.79</td>
			<td>99.5</td>
			<td>99.6</td>
		</tr>
		<tr>
			<td>1</td>
			<td>Fertilizer</td>
			<td>80.25</td>
			<td>12.98</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>2</td>
			<td>Fertilizer</td>
			<td>79.57</td>
			<td>123.77</td>
			<td>98.8</td>
			<td>101.6</td>
		</tr>
		<tr>
			<td>1</td>
			<td>Coal</td>
			<td>78.79</td>
			<td>12.92</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>2</td>
			<td>Coal</td>
			<td>81.27</td>
			<td>12.84</td>
			<td>98.9</td>
			<td>101.8</td>
		</tr>
		<tr>
			<td>1</td>
			<td>Molasses</td>
			<td>79.38</td>
			<td>12.99</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>2</td>
			<td>Molasses</td>
			<td>81.02</td>
			<td>12.72</td>
			<td>99.2</td>
			<td>100.9</td>
		</tr>
		<tr>
			<td>Mean</td>
			<td></td>
			<td>80.3</td>
			<td>12.85</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>SD</td>
			<td></td>
			<td>0.885</td>
			<td>0.09</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td colspan="6">a Final concentration of FA + HA of 2.5 g/L added to 0.1 M NaOH. (data taken from Lamar et al., 2015)</td>
		</tr>
	</tbody>
</table>
Table 3. Effect of adulterants on quantitation of HA and HFA from a Gascoyne leonardite. (Data taken from Lamar et al., 2015)
<table border="1" fo:keep-together.within-page="1">
	<tbody>
		<tr>
			<td colspan="4">HA</td>
		</tr>
		<tr>
			<td>Sample ID</td>
			<td>Extracted, mg</td>
			<td>Recovered, mg</td>
			<td>Recovered, %</td>
		</tr>
		<tr>
			<td>1</td>
			<td>24.6</td>
			<td>23.7</td>
			<td>96.3</td>
		</tr>
		<tr>
			<td>2</td>
			<td>22.6</td>
			<td>19.9</td>
			<td>88.1</td>
		</tr>
		<tr>
			<td>3</td>
			<td>25.2</td>
			<td>23.6</td>
			<td>93.7</td>
		</tr>
		<tr>
			<td>4</td>
			<td>22.5</td>
			<td>21.5</td>
			<td>95.6</td>
		</tr>
		<tr>
			<td>5</td>
			<td>23.9</td>
			<td>21.8</td>
			<td>91.2</td>
		</tr>
		<tr>
			<td>6</td>
			<td>23.2</td>
			<td>20.8</td>
			<td>89.7</td>
		</tr>
		<tr>
			<td>7</td>
			<td>24</td>
			<td>23.2</td>
			<td>96.7</td>
		</tr>
		<tr>
			<td>Mean</td>
			<td>23.7</td>
			<td>22.1</td>
			<td>93</td>
		</tr>
		<tr>
			<td>SD</td>
			<td>1.01</td>
			<td>1.52</td>
			<td>3.43</td>
		</tr>
		<tr>
			<td>RSD, %</td>
			<td>4.35</td>
			<td>6.88</td>
			<td>3.67</td>
		</tr>
		<tr>
			<td colspan="4">(data taken from Lamar et al., 2014)</td>
		</tr>
	</tbody>
</table>
Table 4. Recovery of HA from spiked blanks. (Data taken from Lamar et al., 2014)
<table border="1" fo:keep-together.within-page="1">
	<tbody>
		<tr>
			<td colspan="4">FA</td>
		</tr>
		<tr>
			<td>Sample ID</td>
			<td>Extracted, mg</td>
			<td>Recovered, mg</td>
			<td>Recovered, %</td>
		</tr>
		<tr>
			<td>1</td>
			<td>19.9</td>
			<td>19</td>
			<td>95.48</td>
		</tr>
		<tr>
			<td>2</td>
			<td>23.1</td>
			<td>22.9</td>
			<td>99.13</td>
		</tr>
		<tr>
			<td>3</td>
			<td>20.7</td>
			<td>19.4</td>
			<td>93.72</td>
		</tr>
		<tr>
			<td>4</td>
			<td>20.5</td>
			<td>19.8</td>
			<td>96.39</td>
		</tr>
		<tr>
			<td>5</td>
			<td>20.8</td>
			<td>21.6</td>
			<td>103.85</td>
		</tr>
		<tr>
			<td>6</td>
			<td>21.9</td>
			<td>20.1</td>
			<td>91.78</td>
		</tr>
		<tr>
			<td>7</td>
			<td>22.7</td>
			<td>22.3</td>
			<td>98.24</td>
		</tr>
		<tr>
			<td>Mean</td>
			<td>21.37</td>
			<td>20.73</td>
			<td>96.94</td>
		</tr>
		<tr>
			<td>SD</td>
			<td>1.21</td>
			<td>1.53</td>
			<td>3.95</td>
		</tr>
		<tr>
			<td>RSD, %</td>
			<td>5.64</td>
			<td>7.36</td>
			<td>4.07</td>
		</tr>
		<tr>
			<td colspan="4">(Data taken from Lamar et al., 2014)</td>
		</tr>
	</tbody>
</table>
Table 5. Recovery of HFA from spiked blanks. (Data taken from Lamar et al., 2014)

Watch this Scientific Journal Video about Quantification of Humic and Fulvic Acids in Humate Ores, DOC, Humified Materials and Humic Substance-Containing Commercial Products at JoVE.com

Quantification of Humic and Fulvic Acids in Humate Ores, DOC, Humified Materials and Humic Substance-Containing Commercial Products

This method provides a gravimetric quantification of humic substances (e.g., humic and fulvic acids) on an ash-free basis, in dry and liquid materials from soft coals (i.e., oxidized and non-oxidized lignite and sub-bituminous coal), humate ores and shales, peats, composts and commercial fertilizers and soil amendments.

The purpose of this method is to provide an accurate and precise concentration of humic (HA) and/or fulvic acids (FA) in soft coals, humic ores and ...

quantification-humic-fulvic-acids-humate-ores-doc-humified-materials

Research

JoVE Journal

Biochemistry

16.3K Views.  Bio Huma Netics, Inc.. This method provides a gravimetric quantification of humic substances (e.g., humic and fulvic acids) on an ash-free basis, in dry and liquid materials from soft coals (i.e., oxidized and non-oxidized lignite and sub-bituminous coal), humate ores and shales, peats, composts and commercial fertilizers and soil amendments.

Video: Quantification of Humic and Fulvic Acids in Humate Ores, DOC, Humified Materials and Humic Substance-Containing Commercial Products

Physical, Chemical and Biological Characterization of Six Biochars Produced for the Remediation of Contaminated Sites

The physical and chemical properties of biochar vary based on feedstock sources and production conditions, making it possible to engineer biochars with specific functions (e.g. carbon sequestration, soil quality improvements, or contaminant sorption). In 2013, the International Biochar Initiative (IBI) made publically available their Standardized Product Definition and Product Testing Guidelines (Version 1.1) which set standards for physical and chemical characteristics for biochar. Six biochars made from three different feedstocks and at two temperatures were analyzed for characteristics related to their use as a soil amendment. The protocol describes analyses of the feedstocks and biochars and includes: cation exchange capacity (CEC), specific surface area (SSA), organic carbon (OC) and moisture percentage, pH, particle size distribution, and proximate and ultimate analysis. Also described in the protocol are the analyses of the feedstocks and biochars for contaminants including polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs), metals and mercury as well as nutrients (phosphorous, nitrite and nitrate and ammonium as nitrogen). The protocol also includes the biological testing procedures, earthworm avoidance and germination assays. Based on the quality assurance / quality control (QA/QC) results of blanks, duplicates, standards and reference materials, all methods were determined adequate for use with biochar and feedstock materials. All biochars and feedstocks were well within the criterion set by the IBI and there were little differences among biochars, except in the case of the biochar produced from construction waste materials. This biochar (referred to as Old biochar) was determined to have elevated levels of arsenic, chromium, copper, and lead, and failed the earthworm avoidance and germination assays. Based on these results, Old biochar would not be appropriate for use as a soil amendment for carbon sequestration, substrate quality improvements or remediation.

Biochar is a carbon-rich material used as a soil amendment with the ability to sustainably sequester carbon, improve substrate quality and sorb contaminants. This protocol describes the 17 analytical methods used for the characterization of biochar, which is required prior to large scale implementation of these amendments in the environment.

The physical and chemical properties of biochar vary based on feedstock sources and production conditions, making it possible to engineer biochars with ...

Environment

Sediment Core Sectioning and Extraction of Pore Waters under Anoxic Conditions

We demonstrate a method for sectioning sediment cores and extracting pore waters while maintaining oxygen-free conditions. A simple, inexpensive system is built and can be transported to a temporary work space close to field sampling site(s) to facilitate rapid analysis. Cores are extruded into a portable glove bag, where they are sectioned and each 1-3 cm thick section (depending on core diameter) is sealed into 50 ml centrifuge tubes. Pore waters are separated with centrifugation outside of the glove bag and then returned to the glove bag for separation from the sediment. These extracted pore water samples can be analyzed immediately. Immediate analyses of redox sensitive species, such as sulfide, iron speciation, and arsenic speciation indicate that oxidation of pore waters is minimal; some samples show approximately 100% of the reduced species, e.g. 100% Fe(II) with no detectable Fe(III). Both sediment and pore water samples can be preserved to maintain chemical species for further analysis upon return to the laboratory.

A protocol for sectioning sediment cores and extracting pore waters under anoxic conditions in order to permit analysis of redox sensitive species in both solids and fluids is presented.

We demonstrate a method for sectioning sediment cores and extracting pore waters while maintaining oxygen-free conditions. A simple, inexpensive system is ...

Assessment of Labile Organic Carbon in Soil Using Sequential Fumigation Incubation Procedures

Management practices and environmental changes can alter soil nutrient and carbon cycling. Soil labile organic carbon, a readily decomposable C pool, is highly sensitive to disturbance. It is also the primary substrate for soil microorganisms, which is fundamental to nutrient cycling. Due to these attributes, labile organic carbon (LOC) has been identified as an indicator parameter for soil health. Quantifying the turnover rate of LOC also aids in understanding changes in soil nutrient cycling processes. A sequential fumigation incubation method has been developed to estimate soil LOC and potential C turnover rate. The method requires fumigating soil samples and quantifying CO2-C respired during a 10 day incubation period over a series of fumigation-incubation cycles. Labile organic C and potential C turnover rate are then extrapolated from accumulated CO2 with a negative exponential model. Procedures for conducting this method are described.

Labile organic carbon (LOC) and the potential carbon turnover rate are sensitive indicators of changes in soil nutrient cycling processes. Details are provided for a method based on fumigating and incubating soil in a series of cycles and using the CO2 accumulated during the incubation periods to estimate these parameters.

Management practices and environmental changes can alter soil nutrient and carbon cycling. Soil labile organic carbon, a readily decomposable C pool, is ...

Extraction and Characterization of Surfactants from Atmospheric Aerosols

Surface-active compounds, or surfactants, present in atmospheric aerosols are expected to play important roles in the formation of liquid water clouds in the Earth&#39;s atmosphere, a central process in meteorology, hydrology, and for the climate system. But because specific extraction and characterization of these compounds have been lacking for decades, very little is known on their identity, properties, mode of action and origins, thus preventing the full understanding of cloud formation and its potential links with the Earth&#39;s ecosystems.
In this paper we present recently developed methods for 1) the targeted extraction of all the surfactants from atmospheric aerosol samples and for the determination of 2) their absolute concentrations in the aerosol phase and 3) their static surface tension curves in water, including their Critical Micelle Concentration (CMC). These methods have been validated with 9 references surfactants, including anionic, cationic and non-ionic ones. Examples of results are presented for surfactants found in fine aerosol particles (diameter &#60;1 &#956;m) collected at a coastal site in Croatia and suggestions for future improvements and other characterizations than those presented are discussed.

Methods are presented for the targeted extraction of surfactants present in atmospheric aerosols and the determination of their absolute concentrations and surface tension curves in water, including their Critical Micelle Concentration (CMC).

Surface-active compounds, or surfactants, present in atmospheric aerosols are expected to play important roles in the formation of liquid water clouds in ...

Determination of Inorganic Arsenic in a Wide Range of Food Matrices using Hydride Generation - Atomic Absorption Spectrometry.

The European Food Safety Authority (EFSA) underlined in its Scientific Opinion on Arsenic in Food that in order to support a sound exposure assessment to inorganic arsenic through diet, information about distribution of arsenic species in various food types must be generated. A method, previously validated in a collaborative trial, has been applied to determine inorganic arsenic in a wide variety of food matrices, covering grains, mushrooms and food of marine origin (31 samples in total). The method is based on detection by flow injection-hydride generation-atomic absorption spectrometry of the iAs selectively extracted into chloroform after digestion of the proteins with concentrated HCl. The method is characterized by a limit of quantification of 10 &#181;g/kg dry weight, which allowed quantification of inorganic arsenic in a large amount of food matrices. Information is provided about performance scores given to results obtained with this method and which were reported by different laboratories in several proficiency tests. The percentage of satisfactory results obtained with the discussed method is higher than that of the results obtained with other analytical approaches.

The usefulness of an analytical method to determine inorganic arsenic in a wide range of food matrices is demonstrated. The method consists of selective extraction of inorganic arsenic into chloroform with a final determination by hydride generation-atomic absorption spectrometry.

The European Food Safety Authority (EFSA) underlined in its Scientific Opinion on Arsenic in Food that in order to support a sound exposure assessment to ...

Improving Infrared Spectroscopy Characterization of Soil Organic Matter with Spectral Subtractions

Soil organic matter (SOM) underlies numerous soil processes and functions. Fourier transform infrared (FTIR) spectroscopy detects infrared-active organic bonds that constitute the organic component of soils. However, the relatively low organic matter content of soils (commonly &#60; 5% by mass) and absorbance overlap of mineral and organic functional groups in the mid-infrared (MIR) region (4,000-400 cm-1) engenders substantial interference by dominant mineral absorbances, challenging or even preventing interpretation of spectra for SOM characterization. Spectral subtractions, a post-hoc mathematical treatment of spectra, can reduce mineral interference and enhance resolution of spectral regions corresponding to organic functional groups by mathematically removing mineral absorbances. This requires a mineral-enriched reference spectrum, which can be empirically obtained for a given soil sample by removing SOM. The mineral-enriched reference spectrum is subtracted from the original (untreated) spectrum of the soil sample to produce a spectrum representing SOM absorbances. Common SOM removal methods include high-temperature combustion (&#39;ashing&#39;) and chemical oxidation. Selection of the SOM removal method carries two considerations: (1) the amount of SOM removed, and (2) absorbance artifacts in the mineral reference spectrum and thus the resulting subtraction spectrum. These potential issues can, and should, be identified and quantified in order to avoid fallacious or biased interpretations of spectra for organic functional group composition of SOM. Following SOM removal, the resulting mineral-enriched sample is used to collect a mineral reference spectrum. Several strategies exist to perform subtractions depending on the experimental goals and sample characteristics, most notably the determination of the subtraction factor. The resulting subtraction spectrum requires careful interpretation based on the aforementioned methodology. For many soil and other environmental samples containing substantial mineral components, subtractions have strong potential to improve FTIR spectroscopic characterization of organic matter composition.

SOM underlies many soil functions and processes, but its characterization by FTIR spectroscopy is often challenged by mineral interferences. The described method can increase the utility of SOM analysis by FTIR spectroscopy by subtracting mineral interferences in soil spectra using empirically obtained mineral reference spectra.

Soil organic matter (SOM) underlies numerous soil processes and functions. Fourier transform infrared (FTIR) spectroscopy detects infrared-active organic ...

Combined Size and Density Fractionation of Soils for Investigations of Organo-Mineral Interactions

Combined size and density fractionation (CSDF) is a method used to physically separate soil into fractions differing in particle size and mineralogy. CSDF relies on sequential density separation and sedimentation steps to isolate (1) the free light fraction (uncomplexed organic matter), (2) the occluded light fraction (uncomplexed organic matter trapped in soil aggregates) and (3) a variable number of heavy fractions (soil minerals and their associated organic matter) differing in composition. Provided that the parameters of the CSDF (dispersion energy, density cut-offs, sedimentation time) are properly selected, the method yields heavy fractions of relatively homogeneous mineral composition. Each of these fractions is expected to have a different complexing ability towards organic matter, rendering this a useful method to isolate and study the nature of organo-mineral interactions. Combining density and particle size separation brings an improved resolution compared to simple size or density fractionation methods, allowing the separation of heavy components according to both mineralogy and size (related to surface area) criteria. As is the case for all physical fractionation methods, it may be considered as less disruptive or aggressive than chemically-based extraction methods. However, CSDF is a time-consuming method and furthermore, the quantity of material obtained in some fractions can be limiting for subsequent analysis. Following CSDF, the fractions may be analyzed for mineralogical composition, soil organic carbon concentration and organic matter chemistry. The method provides quantitative information about organic carbon distribution within a soil sample and brings light to the sorptive capacity of the different, naturally-occurring mineral phases, thus providing mechanistic information about the preferential nature of organo-mineral interactions in soils (i.e., which minerals, what type of organic matter).

Combined size and density fractionation (CSDF) is a method to physically separate soil into fractions differing in texture (particle size) and mineralogy (density). The purpose is to isolate fractions with different reactivities towards soil organic matter (SOM), in order to better understand organo-mineral interactions and SOM dynamics.

Combined size and density fractionation (CSDF) is a method used to physically separate soil into fractions differing in particle size and mineralogy. CSDF ...

Single-throughput Complementary High-resolution Analytical Techniques for Characterizing Complex Natural Organic Matter Mixtures

Natural organic matter (NOM) is composed of a highly complex mixture of thousands of organic compounds which, historically, proved difficult to characterize. However, to understand the thermodynamic and kinetic controls on greenhouse gas (carbon dioxide [CO2] and methane [CH4]) production resulting from the decomposition of NOM, a molecular-level characterization coupled with microbial proteome analyses is necessary. Further, climate and environmental changes are expected to perturb natural ecosystems, potentially upsetting complex interactions that influence both the supply of organic matter substrates and the microorganisms performing the transformations. A detailed molecular characterization of the organic matter, microbial proteomics, and the pathways and transformations by which organic matter is decomposed will be necessary to predict the direction and magnitude of the effects of environmental changes. This article describes a methodological throughput for comprehensive metabolite characterization in a single sample by direct injection Fourier transform ion cyclotron resonance mass spectrometry (FTICR-MS), gas chromatography mass spectrometry (GC-MS), nuclear magnetic resonance (NMR) spectroscopy, liquid chromatography mass spectrometry (LC-MS), and proteomics analysis. This approach results in a fully-paired dataset which improves statistical confidence for inferring pathways of organic matter decomposition, the resulting CO2 and CH4 production rates, and their responses to environmental perturbation. Herein we present results of applying this method to NOM samples collected from peatlands; however, the protocol is applicable to any NOM sample (e.g., peat, forested soils, marine sediments, etc.).

This protocol describes a single throughput for complementary analytical and omics techniques culminating in a fully-paired characterization of natural organic matter and microbial proteomics in different ecosystems. This approach permits robust comparisons for identifying metabolic pathways and transformations important for describing greenhouse gas production and predicting responses to environmental change.

Natural organic matter (NOM) is composed of a highly complex mixture of thousands of organic compounds which, historically, proved difficult to ...

Monitoring Pedogenic Inorganic Carbon Accumulation Due to Weathering of Amended Silicate Minerals in Agricultural Soils.

The present study aims to demonstrate a systematic procedure for monitoring inorganic carbon induced by enhanced weathering of comminuted rocks in agricultural soils. To this end, the core soil samples taken at different depth (including 0-15 cm, 15-30 cm, and 30-60 cm profiles) are collected from an agriculture field, the topsoil of which has already been enriched with an alkaline earth metal silicate containing mineral (such as wollastonite). After transporting to the laboratory, the soil samples are air-dried and sieved. Then, the inorganic carbon content of the samples is determined by a volumetric method called calcimetry. The representative results presented herein showed five folded increments of inorganic carbon content in the soils amended with the Ca-silicate compared to control soils. This compositional change was accompanied by more than 1 unit of pH increase in the amended soils, implying high dissolution of the silicate. Mineralogical and morphological analyses, as well as elemental composition, further corroborate the increase in the inorganic carbon content of silicate-amended soils. The sampling and analysis methods presented in this study can be adopted by researchers and professionals looking to trace pedogenic inorganic carbon changes in soils and subsoils, including those amended with other suitable silicate rocks such as basalt and olivine. These methods can also be exploited as tools for verifying soil inorganic carbon sequestration by private and governmental entities to certify and award carbon credits.

The verification method described here is adaptable for monitoring pedogenic inorganic carbon sequestration in various agricultural soils amended with alkaline earth metal silicate-containing rocks, such as wollastonite, basalt, and olivine. This type of validation is essential for carbon credit programs, which can benefit farmers that sequester carbon in their fields.

The present study aims to demonstrate a systematic procedure for monitoring inorganic carbon induced by enhanced weathering of comminuted rocks in ...

Utilizing Soil Density Fractionation to Separate Distinct Soil Carbon Pools

Soil organic matter (SOM) is a complicated mixture of different compounds that span the range from free, partially degraded plant components to more microbially altered compounds held in the soil aggregates to highly processed microbial by-products with strong associations with reactive soil minerals. Soil scientists have struggled to find ways to separate soil into fractions that are easily measurable and useful for soil carbon (C) modeling. Fractionating soil based on density is increasingly being used, and it is easy to perform and yields C pools based on the degree of association between the SOM and different minerals; thus, soil density fractionation can help to characterize the SOM and identify SOM stabilization mechanisms. However, the reported soil density fractionation protocols vary significantly, making the results from different studies and ecosystems hard to compare. Here, we describe a robust density fractionation procedure that separates particulate and mineral-associated organic matter and explain the benefits and drawbacks of separating soil into two, three, or more density fractions. Such fractions often differ in their chemical and mineral composition, turnover time, and degree of microbial processing, as well as the degree of mineral stabilization.

Soil density fractionation separates soil organic matter into distinct pools with differing stabilization mechanisms, chemistries, and turnover times. Sodium polytungstate solutions with specific densities allow the separation of free particulate organic matter and mineral-associated organic matter, resulting in organic matter fractions suitable for describing the soil response to management and climate change.

Soil organic matter (SOM) is a complicated mixture of different compounds that span the range from free, partially degraded plant components to more ...

Quantification of Humic and Fulvic Acids in Humate Ores, DOC, Humified Materials and Humic Substance-Containing Commercial Products

Podsumowanie

Przeglądaj więcej filmów

PLAYLIST