JoVE Logo

Sign In

Rockwell Hardness Test and the Effect of Treatment on Steel

Overview

Source: Roberto Leon, Department of Civil and Environmental Engineering, Virginia Tech, Blacksburg, VA

Hardness testing is one of the most universally valuable mechanical tests available to engineers, as it is both simple and relatively inexpensive for the wealth of information and data it produces. Hardness testing, generally in the form of a surface penetration test, is both quicker and less destructive than tensile testing. Hardness provides a linear relationship with tensile strength over a wide range of strengths for many materials, such as steel. Hardness tests are empirical, rather than derived from theory, as the results conflate effects from many different materials properties (Young's modulus, yield strength, etc.).

Hardness is a characteristic of a material used to describe how much plastic deformation (yield) that a material will undergo when a known force is applied). One can characterize hardness in three manners: scratch, indentation, and rebound hardness. A common early example of a hardness (scratch) test is the Mohs scale (1820), derived for minerals, and in which talc has a value of 1 and diamond a value of 10. In indentation testing using the Rockwell approach, small indenters are used with different loads. The most common are the Rockwell Hardness B (HRB), which uses a 1/16 in. hardened steel ball indenter along with a 100 kg weight, and the Rockwell Hardness C (HRC), which uses a diamond cone indenter along with a 150 kg weight. HRB tests are conducted for materials with low range hardness, such as aluminum, brass, and soft steels, whereas HRC tests are used for materials with high range hardness, such as harder steels. Smaller weights (15 to 45 kg) are used for the Rockwell superficial hardness test such as the HR15W, which uses a 1/8 in. steel ball with a 15 kg weight. With its lower load and shallow impression, a superficial Rockwell hardness test is ideal for very thin or brittle materials. An example of a rebound test is the Schmidt hammer, used to measure the strength of concrete. In this test, a steel mass is shot at the surface with a known force and the rebound of the ball is measured. In all types of hardness testing, it is imperative to conduct extensive calibrations if reliable results are to be obtained.

For this experiment, we will be examining the Rockwell hardness test, which measures indentation hardness of untreated and heat-treated aluminum.

Procedure

The following procedure is for the manual machine shown in Fig. 1. The procedure is typical for other machines as well.

  1. Obtain a typical Jominy end-quench test specimen that has undergone water-cooling treatment.
  2. Secure the specimen to the table of the testing machine so that it will not move during testing.
  3. Ensure selection lever is in "Unloading" position.
  4. Using the adjustment wheel under the support, raise the sample until contact with the indenter is established (wh

Log in or to access full content. Learn more about your institution’s access to JoVE content here

Results

A typical result of Rockwell testing on a Jominy specimen for a HR C test is shown in the video. The hardness decrease appreciably as one moves away from the end subjected to the water jet. The hardness test value can be converted to a tensile strength through charts provided by the testing machine manufacturer. The results show that the steel varies considerably in both hardness and strength as one moves away from the quenched end.

Log in or to access full content. Learn more about your institution’s access to JoVE content here

Application and Summary

Hardness testing is one of the principal tests to garner important engineering information about a material. Rockwell hardness testing is the preferred method of hardness testing, as it eliminates the need for advanced optical equipment, but instead employs basic laboratory equipment to accurately, inexpensively, and quickly measure the hardness of a material. More importantly, this method is easily translated and reproducible between labs and testing personnel because of its relative simplicity. The procedure requires t

Log in or to access full content. Learn more about your institution’s access to JoVE content here

Tags
Rockwell Hardness TestTreatment On SteelHardness TestingMechanical TestsEmpirical ValuesMaterial StrengthPlastic DeformationRockwell type TestingIndentersUntreated SteelHeat treated SteelBrinell Hardness TestVickers Hardness TestKnoop Hardness TestRockwell Hardness BNC TestPenetratorIndentationStructural SteelsManual Rockwell TesterLever SystemAnalog ReadoutPreliminary LoadMajor Load

Skip to...

0:08

Overview

1:01

Principles of the Rockwell Hardness Test

3:38

Measuring Rockwell C Hardness

6:07

Results

6:38

Applications

7:40

Summary

JoVE Logo

Privacy

Terms of Use

Policies

Research

Education

ABOUT JoVE

Copyright © 2024 MyJoVE Corporation. All rights reserved