Per iniziare la stampa 3D dell'infusione diretta dell'impianto o del dispositivo DPI e dei componenti dello stampo, applicare un sottile strato di colla a base di acetato di polivinile sul piano di stampa della stampante. Caricare il filamento di nylon nella stampante e preparare la stampante secondo le istruzioni del produttore. Dopo aver importato i file STL desiderati, configurare la stampante e avviare la stampa.
Una volta rimosso il pezzo dal piano di stampa dopo la stampa, sciacquare la colla a base di polivinilacetato dalla base del componente stampato con acqua. Spruzzare il dispositivo DPI stampato e altri componenti con due mani di vernice spray lucida trasparente. Per fabbricare lo stampo ad anello plastisol, assemblare una forma di stampo costruendo un involucro rettangolare utilizzando blocchi di plastica a scatto su una base.
Dovrebbe essere abbastanza grande da contenere i pezzi del modello. Mescolare il silicone vulcanizzante a temperatura ambiente o il monomero di silicone RTV e il catalizzatore insieme in un rapporto 10: 1 agitando per un minuto. Colorare la soluzione aggiungendo tre gocce di colorante alimentare e un millilitro di sapone per le mani per 25 millilitri di miscela di silicone.
Quindi, versare uno strato sottile della soluzione di silicone nella forma dello stampo sufficientemente per coprire completamente il fondo della forma dello stampo. Tamponare per appiattire la superficie del silicone versato e attendere 24 ore per impostare il silicone. Una volta impostato il silicone, versare un altro strato di silicone abbastanza profondo da coprire la stampa del nucleo del foro centrale del modello.
Inserire il motivo nel silicone liquido con la stampa del nucleo del foro centrale rivolta verso il basso. Assicurati che nessuna bolla sia intrappolata e che i motivi siano ben separati e non si tocchino. Fissare i modelli con un oggetto pesante o un nastro adesivo per evitare che fluttuino fuori dal silicone mentre si fissa.
Una volta impostato, versare ulteriori strati di silicone nella forma dello stampo fino a quando il livello è a filo con la parte superiore del modello. Lasciare polimerizzare il silicone per 24 ore. Smontare i blocchi di plastica a scatto per rilasciare lo stampo.
Quindi, rimuovere i modelli dallo stampo e ispezionare lo stampo per lacrime o deformità. Per colare gli anelli plastisol, rivestire l'interno dello stampo, tutti i componenti principali e gli O-ring con olio da cucina. Posizionare un O-ring attorno alla tacca al centro del nucleo del palo centrale e posizionare il nucleo nel foro centrale dello stampo dell'anello plastisol.
Inserire il nucleo del canale di consegna nello spazio sul lato dello stampo ad anello plastisol. Orientare la punta a forma di V all'estremità del nucleo del canale di mandata per allinearlo con l'O-ring sul nucleo del montante centrale. Successivamente, riscaldare plastisol nel microonde per brevi raffiche di 10 secondi fino a quando la soluzione raggiunge da 160 a 170 gradi Celsius.
Nel mezzo, mescolare delicatamente il plastisol per evitare bolle. Versare il plastisol fuso nello stampo ad anello plastisol vicino al bordo esterno dello stampo senza introdurre bolle. Attendere un'ora affinché gli anelli plastisol si raffreddino.
Quindi, rimuovere gli anelli dallo stampo. Il dispositivo DPI era alto otto centimetri e largo tre centimetri. Aveva un unico serbatoio centrale contiguo al beccuccio.
Il volume totale che può essere contenuto all'interno di questi componenti è di 2,0 millilitri. L'anello plastisol alto 1,8 centimetri e largo 2,7 centimetri conteneva anche due canali. Uno per ospitare il beccuccio del dispositivo DPI e un altro di diametro variabile per il montaggio attorno al tronco dell'albero.
Se assemblato correttamente, l'anello plastisol deve essere a filo contro il dispositivo DPI e il beccuccio deve allinearsi con il foro praticato nell'albero.