Para iniciar a impressão 3D da infusão direta da planta ou do dispositivo DPI e dos componentes do molde, aplique uma fina camada de cola à base de acetato de polivinila no leito de impressão da impressora. Coloque o filamento de nylon na impressora e prepare a impressora de acordo com as instruções do fabricante. Depois de importar os arquivos STL desejados, configure a impressora e comece a imprimir.
Uma vez que a peça é removida da mesa de impressão após a impressão, lave a cola à base de acetato de polivinila da base do componente impresso com água. Borrife o dispositivo DPI impresso e outros componentes com duas demãos de tinta spray de brilho transparente. Para fabricar o molde de anel de plastisol, monte uma forma de molde construindo um gabinete retangular usando blocos de plástico encaixados em uma base.
Deve ser grande o suficiente para segurar as peças padrão. Misture o silício vulcanizante à temperatura ambiente ou o monômero de silicone RTV e o catalisador juntos em uma proporção de 10:1 agitando por um minuto. Colorir a solução adicionando três gotas de corante alimentar e um mililitro de sabão para as mãos por 25 mililitros de mistura de silicone.
Em seguida, despeje uma camada fina da solução de silicone na forma do molde o suficiente para cobrir totalmente o fundo da forma do molde. Tamp para achatar a superfície do silicone derramado, e esperar por 24 horas para definir o silicone. Uma vez que o silicone está definido, despeje outra camada de silicone profunda o suficiente para cobrir a impressão central do núcleo do furo do padrão.
Insira o padrão no silicone líquido com a impressão do núcleo do orifício central voltada para baixo. Certifique-se de que nenhuma bolha esteja presa e os padrões estejam bem separados e não se toquem uns nos outros. Fixe os padrões com um objeto pesado ou fita adesiva para evitar que flutuem para fora do silicone enquanto ele se ajusta.
Uma vez ajustado, despeje camadas adicionais de silicone na forma do molde até que o nível fique nivelado com a parte superior do padrão. Deixe o silicone curar por 24 horas. Desmonte os blocos plásticos para soltar o molde.
Em seguida, remova os padrões do molde e inspecione o molde em busca de rasgos ou deformidades. Para fundir os anéis de plastisol, cubra o interior do molde, todos os componentes do núcleo e os anéis O com óleo de cozinha. Coloque um anel O ao redor do entalhe no meio do núcleo do poste central e coloque o núcleo no orifício central do molde do anel de plastisol.
Insira o núcleo do canal de entrega no espaço na lateral do molde do anel de plastisol. Oriente a ponta em forma de V no final do núcleo do canal de entrega para alinhar com o anel O no núcleo do poste central. Em seguida, aqueça o plastisol no micro-ondas por rajadas curtas de 10 segundos até que a solução atinja 160 a 170 graus Celsius.
Pelo meio, mexa o plastisol suavemente para evitar bolhas. Despeje o plastisol derretido no molde do anel de plastisol perto da borda externa do molde sem introduzir bolhas. Aguarde uma hora para que os anéis de plastisol esfriem.
Em seguida, retire os anéis do molde. O aparelho de IPD tinha oito centímetros de altura e três centímetros de largura. Possuía um único reservatório central contíguo à bica.
O volume total que pode ser contido dentro desses componentes é de 2,0 mililitros. O anel de plastisol de 1,8 centímetro de altura e 2,7 centímetros de largura também continha dois canais. Um para acomodar o bico do dispositivo DPI e outro de diâmetro variável para encaixe ao redor do tronco da árvore.
Quando montado corretamente, o anel de plastisol deve ser nivelado contra o dispositivo de DPI e o bico deve se alinhar com o furo perfurado na árvore.