Para comenzar a imprimir en 3D la infusión directa de la planta o el dispositivo DPI y los componentes del molde, aplique una capa delgada de pegamento a base de acetato de polivinilo en el lecho de impresión de la impresora. Cargue filamento de nylon en la impresora y prepare la impresora según las instrucciones del fabricante. Después de importar los archivos STL deseados, configure la impresora y comience a imprimir.
Una vez que la pieza se retire de la cama de impresión después de la impresión, enjuague el pegamento a base de acetato de polivinilo de la base del componente impreso con agua. Rocíe el dispositivo DPI impreso y otros componentes con dos capas de pintura en aerosol brillante transparente. Para fabricar el molde de anillo de plastisol, ensamble una forma de molde construyendo un recinto rectangular utilizando bloques de plástico a presión sobre una base.
Debe ser lo suficientemente grande como para sostener las piezas del patrón. Mezcle la silicona vulcanizante a temperatura ambiente o el monómero de silicona RTV y el catalizador en una proporción de 10: 1 agitando durante un minuto. Coloree la solución agregando tres gotas de colorante alimentario y un mililitro de jabón de manos por cada 25 mililitros de mezcla de silicona.
Luego, vierta una capa delgada de la solución de silicona en la forma del molde lo suficiente como para cubrir completamente la parte inferior de la forma del molde. Tamp para aplanar la superficie de la silicona vertida y espere 24 horas para fijar la silicona. Una vez que la silicona esté establecida, vierta otra capa de silicona lo suficientemente profunda como para cubrir la impresión del núcleo del orificio central del patrón.
Inserte el patrón en la silicona líquida con la impresión del núcleo del orificio central hacia abajo. Asegúrese de que no queden burbujas atrapadas y que los patrones estén bien separados y no se toquen entre sí. Asegure los patrones con un objeto pesado o cinta adhesiva para evitar que floten fuera de la silicona mientras se asienta.
Una vez establecido, vierta capas adicionales de silicona en la forma del molde hasta que el nivel esté al ras con la parte superior del patrón. Deje que la silicona se cure durante 24 horas. Desmonte los bloques de plástico a presión para liberar el molde.
Luego, retire los patrones del molde e inspeccione el molde en busca de desgarros o deformidades. Para fundir los anillos de plastisol, cubra el interior del molde, todos los componentes principales y las juntas tóricas con aceite de cocina. Coloque una junta tórica alrededor de la muesca en el centro del núcleo del poste central y coloque el núcleo en el orificio central del molde del anillo de plastisol.
Inserte el núcleo del canal de entrega en el espacio en el costado del molde del anillo de plastisol. Oriente la punta en forma de V al final del núcleo del canal de entrega para alinearla con la junta tórica en el núcleo del poste central. A continuación, caliente el plastisol en el microondas durante ráfagas cortas de 10 segundos hasta que la solución alcance los 160 a 170 grados centígrados.
En el medio, revuelva el plastisol suavemente para evitar burbujas. Vierta el plastisol fundido en el molde del anillo de plastisol cerca del borde exterior del molde sin introducir burbujas. Espere una hora para que los anillos de plastisol se enfríen.
Luego, retire los anillos del molde. El dispositivo DPI tenía ocho centímetros de altura y tres centímetros de ancho. Tenía un solo depósito central contiguo al pico.
El volumen total que se puede contener dentro de estos componentes es de 2.0 mililitros. El anillo de plastisol de 1,8 centímetros de alto y 2,7 centímetros de ancho también contenía dos canales. Uno para acomodar el pico del dispositivo DPI y otro de diámetro variable para encajar alrededor del tronco del árbol.
Cuando se ensambla correctamente, el anillo de plastisol debe estar al ras contra el dispositivo DPI y el pico debe alinearse con el orificio perforado en el árbol.