För att börja 3D-skriva ut den direkta växtinfusionen eller DPI-enheten och formkomponenter, applicera ett tunt lager polyvinylacetatbaserat lim på skrivarens utskriftsbädd. Fyll på nylonfilament i skrivaren och förbered skrivaren enligt tillverkarens anvisningar. När du har importerat önskade STL-filer ställer du in skrivaren och börjar skriva ut.
När biten har tagits bort från tryckbädden efter utskrift, skölj det polyvinylacetatbaserade limet från basen av den tryckta komponenten med vatten. Spraya den tryckta DPI-enheten och andra komponenter med två lager klarglans sprayfärg. För att tillverka plastisolringformen, montera en formform genom att bygga ett rektangulärt hölje med hjälp av snäppbara plastblock på en bas.
Den ska vara tillräckligt stor för att hålla mönsterbitarna. Blanda rumstemperatur vulkaniserande silikon eller RTV silikonmonomer och katalysatorn tillsammans i förhållandet 10: 1 genom omrörning i en minut. Färga lösningen genom att tillsätta tre droppar matfärg och en milliliter handtvål per 25 ml silikonblandning.
Häll sedan ett tunt lager av silikonlösningen i formformen tillräckligt för att helt täcka botten av formformen. Tampa för att platta ytan på den hällda silikonen och vänta i 24 timmar för att ställa silikon. När silikonet är inställt, häll ytterligare ett lager silikon tillräckligt djupt för att täcka mönstrets mitthålskärntryck.
Sätt in mönstret i det flytande silikonet med mitthålets kärntryck nedåt. Se till att inga bubblor fångas och mönstren är väl separerade och inte vidrör varandra. Säkra mönstren med antingen ett tungt föremål eller tejp för att förhindra att de flyter ut ur silikonet medan det stelnar.
När du har stelnat, häll ytterligare lager silikon i formformen tills nivån är i linje med toppen av mönstret. Låt silikonet härda i 24 timmar. Demontera de snäppbara plastblocken för att frigöra formen.
Ta sedan bort mönstren från formen och inspektera formen för tårar eller missbildningar. För gjutning av plastisolringarna, täck formens inre, alla kärnkomponenter och O-ringarna med matolja. Placera en O-ring runt skåran i mitten av mittstolpkärnan och placera kärnan i plastisolringformens mitthål.
Sätt in leveranskanalkärnan i utrymmet på sidan av plastisolringformen. Rikta in den V-formade spetsen i slutet av leveranskanalens kärna för att anpassa den till O-ringen på mittstolpens kärna. Värm sedan plastisol i mikrovågsugnen i korta skurar på 10 sekunder tills lösningen når 160 till 170 grader Celsius.
Däremellan, rör plastisolen försiktigt för att undvika bubblor. Häll den smälta plastisolen i plastisolringformen nära formens ytterkant utan att införa bubblor. Vänta en timme tills plastisolringarna har svalnat.
Ta sedan bort ringarna från formen. DPI-enheten var åtta centimeter hög och tre centimeter bred. Den hade en enda central reservoar som gränsade till pipen.
Den totala volymen som kan finnas inom dessa komponenter är 2, 0 ml. Den 1,8 centimeter långa och 2,7 centimeter breda plastisolringen innehöll också två kanaler. En för att rymma DPI-enhetens pip och en annan med variabel diameter för montering runt trädets stam.
När den är korrekt monterad ska plastisolringen spolas mot DPI-enheten och pipen ska ligga i linje med hålet som borrats i trädet.