Novel 3D-Printed Direct Plant Infusion 또는 DPI 장치를 사용하여 식물에 화합물을 적용하려면 장치가 식물에 제대로 장착되었는지 확인하십시오. 제대로 조립되면 플라스티졸 링이 DPI 장치와 같은 높이가 되어야 하고 스파우트가 나무에 뚫린 구멍과 일직선이 되어야 합니다. 주사기 또는 피펫을 사용하여 DPI 장치에 관심 있는 복합 용액을 채웁니다.
주사기를 사용하여 DPI 장치 반대쪽에 있는 실리콘 테이프와 플라스티졸 링을 관통하여 내부 채널에서 공기를 추출합니다. 추출된 화합물을 DPI 장치로 다시 교체합니다. 주사기로 만든 구멍 위에 작은 실리콘 테이프 패치를 추가하여 해당 부위를 강화하고 찢어지는 것을 방지합니다.
장치의 부착 지점에서 눈에 보이는 누출이 있는지 검사하고 장치 저장소의 액체 레벨이 안정적인지 검사합니다. DPI 장치의 열린 끝을 왁스 밀봉 필름으로 덮고 아래로 당겨 밀봉을 형성하여 실험 화합물의 증발을 줄입니다. 진공의 발생을 방지하기 위해 주사기 팁으로 왁스 필름에 구멍을 뚫고 장치를 다시 채우십시오.
구성 요소가 적절하게 정렬되었는지 확인하기 위해 매일 장치를 점검하고 원하는 양이 전달될 때까지 저장소가 마르지 않도록 주사기를 사용하여 액체를 보충하십시오. DPI 장치를 사용하여 2밀리몰 CFDA 염료 2밀리리터를 식물에 도입했을 때, 처리된 식물의 맥관 구조에서 형광 신호가 검출되었지만, 물에서 20% DMSO로 처리된 대조 식물에는 없었습니다. 이러한 신호는 처리 24시간 이내에, 해부된 식물 조직 유형 전체에 걸쳐 고르게 관찰되었다.
칸디다투스 리베리박터 아시아티쿠스(Candidatus Liberibacter Asiaticus) 또는 CLass 양성 식물에 스트렙토마이신을 처리한 결과 대조군에 비해 처리 후 28일까지 평균 박테리아 역가가 감소한 것으로 나타났습니다. 처리된 식물은 모든 조합된 시점에 걸쳐 더 낮은 평균 CLas 역가를 나타내었다. 스트렙토마이신 처리된 식물은 대조군과 비교하여 60일 후에 새로운 건강한 홍조 성장의 때때로 증가를 보여주었습니다.
식물에 대한 이미다클로프리드 처리는 해당 난자 수에 비해 가장 높은 이미다클로프리드 농도에서 님프 출현을 유의하게 감소시켰습니다. 이것은 님프 단물 생산의 감소에서 시각적으로 분명했습니다.