먼저 RPA(Radiation Planning Assistant)를 시작합니다. 그런 다음 서비스 요청 채널을 클릭하여 RPA 인터페이스의 서비스 요청 대시보드로 이동합니다. 그런 다음 새 양식을 클릭하여 새 요청 양식을 생성합니다.
인구 통계라는 제목의 첫 번째 섹션 아래에 있는 질문을 완료합니다. 그런 다음 치료 풀다운 메뉴에서 치료 기술을 선택합니다. 치료 기법 풀다운 메뉴에서 정보 아이콘을 클릭하면 치료 기법에 대한 자세한 내용을 볼 수 있습니다.
다음으로, 치료 일반 질문이라는 제목의 두 번째 섹션에 있는 질문을 완료합니다. 이제 '치료별 질문'이라는 제목의 섹션 3으로 이동하여 치료 목표 및 처방에 대한 세부 사항을 포함한 질문을 완료합니다. 제출을 클릭하여 서비스 요청 PDF를 생성합니다.
환자 목록에서 환자를 선택합니다. 서비스 요청 PDF를 검토하고 동의를 클릭하여 승인합니다. 그런 다음 CT 스캔 채널을 클릭하여 CT 스캔 대시보드로 이동합니다.
옵션을 선택하고 CT를 업로드한 다음 폴더 탐색기를 사용하여 CT 스캔이 저장된 폴더를 선택합니다. 프롬프트에 따라 선택을 확인합니다. 환자 목록에서 환자를 선택하여 업로드된 해당 CT 스캔을 검토합니다.
그런 다음 3D 로드를 클릭하여 전체 3D CT 이미지를 로드합니다. 이제 CT 보기 아래에 있는 앞으로 또는 뒤로 버튼을 사용하여 모든 보기의 분할 영역 사이를 스크롤하여 다음 분할 영역으로 이동합니다. 오른쪽 Shift 또는 왼쪽 Shift 버튼을 클릭하여 어느 방향으로든 5개의 분할 영역을 이동합니다.
또는 커서를 보기 위로 이동하고 마우스를 사용하여 조각 사이를 스크롤합니다. 교차 버튼을 클릭하여 각 CT 뷰에 십자선을 오버레이할 수도 있습니다. 그런 다음 세 가지 보기 중 하나를 클릭하여 십자선을 이동하면 다른 보기가 그에 따라 따라오게 됩니다.
이미지를 확대하여 확대/축소 팬 버튼을 사용하여 자세히 검토합니다. 그런 다음 마우스 오른쪽 버튼을 클릭하고 마우스를 사용하여 CT 보기를 누른 상태로 확대/축소합니다. 표시된 ISO를 클릭하여 CT 뷰를 표시된 ISO 중심으로 이동합니다.
참조점을 추가하려면 먼저 교차 도구를 사용하여 세 개의 뷰를 원하는 참조점 위치로 이동합니다. 그런 다음 참조점 버튼을 클릭하여 참조점을 추가합니다. 새 참조점을 추가하려면 참조점 지우기를 클릭하여 현재 점을 지웁니다.
그런 다음 새 항목을 추가합니다. CT 스캔을 수락합니다. 그런 다음 CT 이미지 아래의 질문에 답하여 후속 RPA 계산에서 위험을 최소화하고 오류를 줄입니다.
이제 수락을 클릭하고 프롬프트를 따릅니다. 모니터링 프로세스를 시작하려면 먼저 환자를 선택하고 기본 대시보드 상단에서 검토를 선택하여 완료된 RPA 계획을 검토합니다. 다운로드 아이콘을 클릭하여 완료된 RPA 계획을 다운로드합니다.
새 창이 열리면 RPA 계획 보고서의 PDF 버전과 함께 DICOM 파일이 다운로드되어 치료 계획 시스템으로 가져올 수 있습니다. 최종 계획을 웹 사이트에 업로드하려면 환자를 선택하고 계획 업로드를 클릭합니다. 업로드할 DICOM 구조 파일, 계획 및 선량 파일을 선택합니다.
마지막으로 환자를 선택하여 계획 비교 보고서를 검토합니다. 여기에는 전뇌 방사선 치료 계획의 측면 필드의 예가 나와 있으며, 자궁경부암에 대한 뼈 랜드마크 기반 4필드 박스 계획의 측면 필드도 표시됩니다. 두 경우 모두 RPA는 사용자의 치료 계획 시스템을 다운로드하고 가져온 후 최종 계획 보고서를 생성했습니다.
서비스 요청 대시보드는 RPA의 현재 환자에 대한 서비스 요청에 대한 빠른 상태 개요를 제공합니다.