Begynn med å starte Radiation Planning Assistant, eller RPA. Gå deretter til instrumentbordet for serviceforespørsel på RPA-grensesnittet ved å klikke serviceforespørselskanalen. Klikk deretter på det nye skjemaet for å generere et nytt forespørselsskjema.
Fullfør spørsmålene under den første delen med tittelen Demografi. Velg deretter behandlingsteknikk fra rullegardinmenyen for behandling. Klikk på informasjonsikonet i rullegardinmenyen for behandlingsteknikk for å få tilgang til ytterligere detaljer om behandlingsteknikken.
Deretter fullfører du spørsmålene i den andre delen med tittelen Generelle spørsmål om behandling. Gå nå til seksjon tre med tittelen Behandlingsspesifikke spørsmål og fullfør spørsmålene, inkludert detaljene i behandlingsmålene og resept. Klikk på send for å generere PDF-filen med serviceforespørselen.
Velg pasienten i pasientlisten. Se gjennom PDF-filen med serviceforespørselen, og klikk Godta for å godkjenne den. Deretter går du til CT Scans-dashbordet ved å klikke på CT Scans-kanalen.
Velg alternativet, last opp CT og velg mappen der CT-skanningen er lagret ved hjelp av mappeutforsker. Følg instruksjonene for å bekrefte valget. Velg pasienten i pasientlisten for å se gjennom den tilsvarende opplastede CT-skanningen.
Last deretter inn hele 3D CT-bildet ved å klikke på last inn 3D. Rull nå mellom stykkene i alle visninger ved hjelp av knappene fremover eller bakover under CT-visningen for å flytte til neste stykke. Klikk høyre skift- eller venstre skiftknapp for å flytte fem stykker i begge retninger.
Alternativt kan du flytte markøren over en hvilken som helst visning og bruke musen til å bla mellom stykkene. Skjæringsknappen kan også klikkes for å legge over et trådkors på hver CT-visning. Klikk deretter på en av de tre visningene for å flytte trådkorset, slik at de andre visningene følger tilsvarende.
Zoom inn på bildet for å se gjennom det ytterligere ved hjelp av zoompanoreringsknappen. Høyreklikk deretter og hold nede en CT-visning ved hjelp av musen for å zoome. Klikk på merket ISO for å flytte CT-visningene til det merkede ISO-senteret.
Hvis du vil legge til et referansepunkt, flytter du først de tre visningene til ønsket referansepunkt ved hjelp av skjæringsverktøyet. Deretter klikker du på Ref Point-knappen for å legge til et referansepunkt. For å legge til et nytt referansepunkt, fjern gjeldende punkt ved å klikke på clear ref point.
Legg deretter til en ny. Godta CT-skanningen. Svar deretter på spørsmålene under CT-bildene for å minimere risikoen og redusere feil i de påfølgende RPA-beregningene.
Klikk nå på godta og følg instruksjonene. For å starte overvåkingsprosessen må du først gjennomgå en fullført RPA-plan ved å velge pasienten og velge gjennomgang øverst på hoveddashbordet. Last ned en fullført RPA-plan ved å klikke på nedlastingsikonet.
Når et nytt vindu åpnes, blir DICOM-filene, sammen med PDF-versjonen av RPA-planrapporten, lastet ned for import til behandlingsplanleggingssystemet. For å laste opp den endelige planen til nettstedet, velg pasienten og klikk last opp plan. Velg DICOM-strukturfilen, Plan- og Dosefiler for opplasting.
Til slutt går du gjennom sammenligningsrapporten for planen ved å velge pasienten. Et eksempel på et lateralt felt fra en helhjernestrålebehandlingsplan er vist her, mens et lateralt felt fra en benete landemerkebasert firefeltsboksplan for livmorhalskreft også vises. I begge tilfeller opprettet RPA en endelig planrapport etter å ha lastet ned og importert brukerens behandlingsplanleggingssystem.
Instrumentbordet for serviceforespørsel gir en rask statusoversikt over serviceforespørselen for gjeldende pasienter i RPA.