Open om te beginnen de aanpassoftware en laad de voorbeeldgegevensset. Klik op het menu Surface en selecteer Verstrooid licht aftrekken. Gebruik in het nieuwe venster de pijltjestoetsen en stel het aantal achtergrondspectra in op Gemiddeld tot 10 voor het uitvoeren van achtergrondcorrectie.
Klik op Accepteren om de aftrekking uit te voeren. Verwijder vervolgens de nutteloze delen van het spectrum en concentreer u op het spectrum dat linksonder wordt weergegeven. Klik op eindgolflengten.
Voer nieuwe waarden in en druk op enter. Stel het spectrale venster in op het gewenste golflengtebereik. Ga naar het menu Surface, selecteer Bijsnijden en bevestig door te klikken op OK.To de wijzigingen op te slaan, klik op het menu Bestand, selecteer Bestand opslaan als, klik op OK en sluit de gegevensset.
Open de blanco oplosmiddeldataset en start het tripcorrectieproces door de spectrale weergave aan te passen. Klik in de heatmap-tegel linksboven op het dradenkruis en sleep de verticale lijn naar het blauwe uiteinde van het spectrum, beginnend bij het blauwe golflengtebereik aan het begin van het spectrale venster. Navigeer vervolgens naar het menu Kinetiek en selecteer Fit Solvent Response.
Klik in het nieuwe venster met de titel Fit Solvent Response op de knop Fit. Voer dit uit op ten minste vijf verschillende golflengten verdeeld over het hele spectrum. Klik na het laatste punt op Opslaan en sluit het venster.
Open vervolgens de eerder bijgesneden en op de achtergrond afgetrokken gegevensset. Selecteer in het menu Surface de optie Chirp-correctie. Voeg de recent gemaakte Chirp-correctie toe door Toevoegen uit bestand te kiezen, het bestand te selecteren dat eindigt op FitCoëfficiënten en te bevestigen met OK. Klik op de knop Chirp Correction en bekijk de correctie in het venster linksboven, waarbij u ervoor zorgt dat de gegevens tijdelijk afgevlakt lijken zonder enige kromming.
Als de correctie bevredigend is, voltooit u deze door op de knop Toepassen en afsluiten te klikken. Navigeer naar het bestandsmenu. Selecteer Bestand opslaan als.
Voer een geschikte naam in om de toepassing Chirp-correctie weer te geven en klik vervolgens op OK.To zoek functies in de gegevens die moeten worden verwijderd, navigeer naar de heatmap-tegel linksboven. Gebruik het dradenkruis binnen het negatieve tijdgebied om de begin- en eindgolflengten van de verstrooiingsfunctie te identificeren. Begin met de onderste of blauwe golflengte van 654 nanometer in het spectrum linksonder tegel.
Selecteer de juiste eindgolflengte en voer de waarde in voor het onderste functiebereik. Snijd de gegevens bij door Surface te selecteren in het menu, bijsnijden te kiezen en vervolgens op OK te klikken in het pop-upmenu. Sla de bijsnijdgegevens op met een unieke bestandsnaam die aangeeft aan welke kant van de gegevens het is en sluit het bestand.
Open vervolgens het eerder opgeslagen Chirp-correctiebestand en ga verder met het bereik van de hogere of rode golflengte. Selecteer de linker eindgolflengte op het spectrum in de tegel linksonder en voer de waarde in voor het hogere bereik van de functie. Als u de gegevens wilt bijsnijden, navigeert u naar het menu Surface, selecteert u Bijsnijden en klikt u vervolgens op OK in het pop-upmenu.
Sla de gewasgegevens op met een onderscheidende bestandsnaam om aan te geven welke kant van de gegevens het vertegenwoordigt. Combineer de twee bestanden door naar Bestand te gaan en Meerdere oppervlakken combineren te selecteren. Selecteer beide zijden van de gegevens in het nieuwe venster met Control Click.
Zorg ervoor dat beide bestanden zijn gekozen in het vak Bestandsnaam en klik vervolgens op OK om te bevestigen. Klik op Bestand en kies Bestand opslaan als om het gecombineerde bestand op te slaan. Wijs een unieke bestandsnaam toe om de gecombineerde status aan te geven en klik op OK om op te slaan.
Een gecorrigeerde warmtekaart en representatieve spectragegevens worden hier weergegeven. De resultaten laten zien hoe de gegevens eruit moeten zien na het toepassen van de correcties. De dataset is nu klaar voor montage.