For at begynde skal du konfigurere legenden på grænsefladen, derefter navigere til applikationen og klikke på Kør. I vinduet Kør program skal du vælge Ptolemæus-applikationen. Indstil hoved til Legendon-computeren i omfang og kamera til de respektive computere.
Importer nu forudindstillinger i den forudindstillede manager. I indstillingerne for den firkantede målretningsnode skal du sørge for, at både Sorter mål efter korteste sti og Aktivér automatisk målretning er valgt. I indstillingerne for den firkantede node skal du bekræfte, at ventetiden på, at noden behandler billedet, er markeret.
Føj den firkantede forudindstilling til listen, hvis den ikke allerede er inkluderet. Under avancerede indstillinger skal du markere Indstil disse blænder under billedbehandling og sikre, at blændeværdierne er korrekte. Hvis du vil justere indstillingerne for hele målretningsnoden, skal du markere Tillad brugerbekræftelse af valgte mål.
Fjern markeringen af både kø op mål og spring automatisk hulfinder over. I indstillingen for hele noden skal du markere vent på, at en node behandler billedet, og hele forudindstillingen er på listen til højre. I avancerede indstillinger skal du markere Indstil disse blænder under billeddannelse og bekræfte blændeværdierne.
I indstillingerne for målretningsnoden for eksponering skal du vælge Tillad brugerbekræftelse af valgte mål. Sørg for, at Q up-målene og spring over automatisk hulfinder ikke er markeret. Hvis du vil konfigurere indstillingerne for eksponeringsnode, skal du sikre dig, at ventetiden på, at en node behandler billedet, ikke er markeret.
Bekræft, at eksponeringsforudindstillingen er inkluderet på listen til højre. I avancerede indstillinger skal du vælge Indstil disse blænder under billedbehandling og kontrollere, at disse blændeværdier er nøjagtige. I indstillingerne for fokusnoder skal du sikre dig, at vent på, at en node behandler billedet, ikke er markeret.
Kontroller, at forudindstillingen for automatisk fokusering er angivet til højre, og indstil den ønskede autofokusnøjagtighed til fire gange 10 til de negative seks meter. I fokusnodefokussekvensen skal du kun aktivere to trin til automatisk fokusering af strålehældning. For at justere indstillingerne for Z-fokusnoden skal du sikre dig, at vent på, at en node behandler billedet ikke er markeret.
Bekræft, at hele forudindstillingen er angivet til højre, og indstil den ønskede autofokusnøjagtighed til fem gange 10 til de negative fem meter. I fokussekvensen for Z-fokusnoden skal du kun aktivere to hældningstrin med lav forstørrelse. Når du har bestemt gitterets Z-højde og indsamlet et atlas, skal du bruge den firkantede målretningsknude i Ptolemæus til at finde firkanter.
Overhold de blå cirkler på hver firkant. Hold markøren over hver klat for at se deres størrelse som beregnet af Ptolemæus og registrere størrelsen på de største og mindste klatter. For at ændre tærskelindstillingerne skal du justere minimum- og maksimumfilterområdet for at inkludere ønskelige firkanter og udelukke uønskede.
Tryk på knappen fine firkanter på den øverste værktøjslinje. Finjuster filterområdet, indtil funktionen fine firkanter effektivt retter sig mod firkanterne. I anskaffelsesindstillingerne skal du vælge passende værdier for det maksimale antal mål og antallet af målgrupper, der skal prøves.
Når parametrene er tilfredsstillende, skal du klikke på afspilningsknappen for at fortsætte. Brug derefter linealværktøjet i hele målretningsnoden til at måle diameteren på et hul. I skabelonindstillingerne skal du sikre den målte diameter til den endelige skabelondiameter og klikke på test.
Juster diameterværdien, indtil alle huller viser lyse hvide toppe i deres centre. Klik på test i tærskelindstillingerne. Rediger A-værdien, indtil det binariserede billede tydeligt viser hvide områder udelukkende der, hvor der er huller.
I blobsindstillingerne skal du måle en minimumsafstand fra kanten med linealen og angive denne værdi for at udelukke grænsemål. Filtrer klatter baseret på størrelse, rundhed og ønsket mængde. Hold markøren over blobs for at se deres værdier, og klik på test for at gennemse de aktuelle indstillinger.
Indtast hullernes radius og afstanden mellem dem i gitterindstillingerne. Klik derefter på knappen 42 for at måle referenceintensitetsværdien for et vakuumområde. I anskaffelsesindstillingerne skal du markere brug af delmængde af anskaffelsesmålene og angive den maksimale eksempelværdi til et lavt tal, f.eks. to.
Definer et bredt udvalg af istykkelsesmiddelværdier i standardafvigelser. Brug testmålretning til at randomisere målvalg baseret på ovenstående værdier. Klik på afspilningsknappen for at fortsætte, når alle indstillinger er tilfredsstillende.
I hele indstillingerne skal du indstille shell-scriptet til hlfinding. sh script sti i Ptolemæus installation. Indstil minimumsscoren til mindre end nul.
Indtast hullernes radius, og klik derefter på knappen Vis værdi for at måle referenceintensitetsværdien for et vakuumområde. Klik på test for at finde gitteret af huller. I anskaffelsesindstillinger skal du markere brug af undersæt af anskaffelsesmålene og angive den maksimale eksempelværdi til et lille tal, f.eks. fire.
Indstil en bred vifte af istykkelsesmidler og standardafvigelser. Klik på afspilningsknappen, når du er tilfreds med alle indstillinger. Legendon vil udføre centreret fokus og indsamle billeder med høj forstørrelse, som kan ses i eksponeringsnoden.
Tjek det næste eksponeringsmålretningsbillede for at se, om indstillingerne er tilstrækkelige. Når du er tilfreds, skal du fjerne markeringen af Tillad brugerbekræftelse af valgte mål i indstillingerne for eksponeringsmålretning og hele målretning. Når gitteret er færdigt screening, skal du klikke på fil efterfulgt af exit for at lukke Legendon.
For at konfigurere smart Legendon auto skærm skal du udføre smart Legendons autoskærm. py i et terminalvindue. Vælg GY, og indtast en kommasepareret liste over gitterpladser på skærmen.
Indtast derefter fuldt ud til arbejdsgangen. Indtast navnet på skabelonsessionen for nye sessioner og skabelonsessionernes Z-højdeværdi. En GY åbnes for at indtaste sessionsnavnet og vælge projektforeninger for hvert gitter.
Lad mikroskopet være uden opsyn eller overvåg det i Legendon, Appian og mikroskopcomputeren.