Börja med att ställa in förklaringen i gränssnittet, navigera sedan till programmet och klicka på kör. I fönstret Kör program väljer du Ptolemaios-programmet. Ställ in main på Legendon-datorn i omfång och kameran på respektive dator.
Importera nu förinställningar i förinställningshanteraren. I inställningarna för den fyrkantiga målnoden ser du till att både sortera mål efter kortaste sökväg och aktivera automatisk inriktning är markerade. I inställningarna för den fyrkantiga noden bekräftar du att väntetiden för att noden ska bearbeta avbildningen är markerad.
Lägg till den fyrkantiga förinställningen i listan om den inte redan ingår. Under avancerade inställningar, kontrollera ställ in dessa bländare medan du avbildar och se till att bländarvärdena är korrekta. Om du vill justera inställningarna för hela målnoden markerar du Tillåt användarverifiering av valda mål.
Avmarkera både köa upp mål och hoppa över automatisk hålsökare. I inställningen för hela noden markerar du vänta tills en nod bearbetar bilden och hela förinställningen finns i listan till höger. I avancerade inställningar, kontrollera ställ in dessa bländare medan du avbildar och bekräfta bländarvärdena.
I inställningarna för noden för exponeringsmål väljer du tillåt användarverifiering av valda mål. Se till att Q up-målen och hoppa över den automatiska hålsökaren är avmarkerade. Om du vill konfigurera inställningarna för exponeringsnoden ser du till att väntetiden för att en nod ska bearbeta bilden är avmarkerad.
Kontrollera att den förinställda exponeringen finns med i listan till höger. I avancerade inställningar väljer du ställ in dessa bländare medan du avbildar och kontrollerar att dessa bländarvärden är korrekta. I inställningarna för fokusnoden kontrollerar du att vänteläget tills en nod ska bearbeta avbildningen är avmarkerat.
Kontrollera att förinställningen för autofokus är listad till höger och ställ in önskad autofokusnoggrannhet till fyra gånger 10 till de negativa sex meterna. I fokusnodens fokussekvens aktiverar du endast två autofokussteg för strållutning. Om du vill justera inställningarna för Z-fokusnoden ser du till att vänta på att en nod ska bearbeta bilden är avmarkerad.
Bekräfta att hela förinställningen är listad till höger och ställ in önskad autofokusnoggrannhet till fem gånger 10 till de negativa fem meterna. I fokussekvensen för Z-fokusnoden, aktivera endast två lutningssteg med låg förstoring stage. Efter att ha bestämt rutnätets Z-höjd och samlat in en atlas, använd den fyrkantiga målnoden i Ptolemaios för att hitta rutor.
Observera de blå cirklarna på varje ruta. Hovra över varje blob för att visa deras storlek som beräknas av Ptolemaios och registrera storleken på de största och minsta blobarna. Om du vill ändra tröskelinställningarna justerar du det lägsta och högsta filterintervallet så att det inkluderar önskvärda rutor och utesluter oönskade.
Tryck på knappen för fina rutor i det övre verktygsfältet. Finjustera filterområdet tills funktionen för fina rutor effektivt riktar in sig på rutorna. I anskaffningsinställningarna väljer du lämpliga värden för det maximala antalet objekt och antalet målgrupper som ska samplas.
När parametrarna är tillfredsställande klickar du på uppspelningsknappen för att fortsätta. Använd sedan linjalverktyget i hela målnoden för att mäta diametern på ett hål. I mallinställningarna, se till att den uppmätta diametern är den slutliga malldiametern och klicka på test.
Justera diametervärdet tills alla hål visar ljusa vita toppar i mitten. Klicka på testa i tröskelinställningarna. Ändra A-värdet tills den binäriserade bilden tydligt visar vita områden endast där det finns hål.
I blobinställningarna mäter du ett minsta avstånd från kanten med linjalen och anger det värdet för att exkludera kantmål. Filtrera blobbar baserat på storlek, rundhet och önskad kvantitet. Hovra över blobar för att visa deras värden och klicka på testa för att granska de aktuella inställningarna.
Ange hålens radie och avståndet mellan dem i gitterinställningarna. Klicka sedan på knappen 42 för att mäta referensintensitetsvärdet för ett vakuumområde. I förvärvsinställningarna markerar du använd delmängd av förvärvsmålen och ställer in samplingens maximala värde till ett lågt tal, till exempel två.
Definiera ett brett spektrum av istjockleksmedelvärden i standardavvikelser. Använd testmål för att slumpa målval baserat på ovanstående värden. Klicka på uppspelningsknappen för att fortsätta när alla inställningar är tillfredsställande.
I hela inställningarna anger du shell-skriptet till hlfinding. sh skriptsökväg i Ptolemaios-installationen. Ange minimipoängen till mindre än noll.
Mata in hålens radie och klicka sedan på knappen visa värde för att mäta referensintensitetsvärdet för ett vakuumområde. Klicka på testa för att hitta hålens gitter. I förvärvsinställningarna markerar du använd delmängd av förvärvsmålen och ställer in samplingens maximala värde till ett litet tal, till exempel fyra.
Ställ in ett brett spektrum av istjockleksmedelvärden och standardavvikelser. Klicka på uppspelningsknappen när du är nöjd med alla inställningar. Legendon kommer att utföra centrerad fokus och samla in bilder med hög förstoring som kan ses i exponeringsnoden.
Kontrollera nästa bild för exponeringsinriktning för att se om inställningarna är tillräckliga. När du är nöjd avmarkerar du Tillåt användarverifiering av valda mål i inställningarna för exponeringsinriktning och hela inriktning. När rutnätet är klart klickar du på fil följt av avsluta för att stänga Legendon.
För att ställa in smart Legendon autoskärm, kör smart Legendons autoskärm. PY i ett terminalfönster. Välj GY och mata in en kommaseparerad lista med rutnätsplatser på skärmen.
Mata sedan in full för arbetsflödet. Ange mallsessionens namn för nya sessioner och Z-höjdvärdet för mallsessioner. En GY öppnas för att mata in sessionsnamnet och välja projektassociationer för varje rutnät.
Lämna mikroskopet utan uppsikt eller övervaka det i Legendon, Appian och mikroskopdatorn.