experimental setup and procedure for ice cream melting trials

<meta charset="utf8"></head><body>Studerar glassens smältbeteende med hjälp av ett datorseendesystem

Ice cream is a multi-phase system in which liquid, solid, and gas phases are strictly connected. The continuous liquid phase envelops air bubbles and ice crystals, and it contains partially crystallized fats, colloidal proteins, salts, sugars (eventually crystallized), and stabilizers. The ice cream composition varies depending on the local market requests and possible regulations. Although the processing technology affects the characteristics of the final ice cream, each constituent plays an important role in defining the product quality1. Melting behavior is one of the most important quality indices of ice cream, considering phenomena occurring both during consumption and in the mouth. With heat penetration into the ice cream, ice crystals melt, and water diffuses and mixes with the serum phase, which can drain through the remaining structure2. A fast-melting product is undesirable for comfortable eating but also for guaranteeing a higher heat-shock resistance. However, slow-melting products also indicate some defects in the formulation1. It is known that ice cream microstructure is responsible for melting properties3, but contrasting results have been published so far, showing that knowledge about the influence of microstructural factors on melting is still limited4. Thus, more studies are necessary to elucidate the meltdown mechanism, which is crucial also in the design of new formulations3.
Melting behavior is usually evaluated by gravimetric methods and expressed in terms of starting time and rate of melting5. A given portion of ice cream is placed on a wire mesh in a controlled temperature cabinet, and the weight of the melted product is registered. From the weight-time curve, three phases can be highlighted: the lag phase during which heat penetration occurs, the fast-melting phase with the dilute serum phase flowing through the ice cream structure at the maximum rate, and the stationary phase, where most of the product has dripped out2.
With the gravimetric method, slow- and fast-melting products can be recognized; however, the aspect of ice cream during meltdown is important too, because shape retention is linked to a good composition and structure of the product6. Thus, a procedure based on a computer vision system (CVS) can support the already existing gravitational methodology by allowing the study of the product&#39;s appearance during melting. CVSs can acquire numerous food attributes3 (e.g., size, weight, shape, texture, and color) with accurate details that cannot be observed by the human eye. Such systems are usually made of digital cameras and image processing software7. Indeed, a protocol based on CVSs includes two main steps: 1) image acquisition and 2) image processing. Various levels of image processing can be applied7, from the simplest to the more complex, such as deep-learning methods for Artificial Intelligence development8,9. Great attention has been recently paid to CVSs in the food sector, and a high number of applications have been developed for food safety inspection, food processing monitoring, foreign object detection, and other fields. They are fast, efficient, and non-destructive, thus representing valid tools to provide consumers with safe foods of high quality10.
In the field of ice cream, an image analysis method was suggested to study ice recrystallization by optical microscopy11. More recently, X-ray computed tomography images were processed to analyze the 3D microstructure of soft-porous matters, including ice cream3. However, the elaboration of simple digital Charge Coupled Device (CCD) images can present several advantages in terms of easiness of acquisition and rendering of the ice cream aspect as perceived by consumers. Some Authors show images of ice cream during melting12, but, to the best of our knowledge, the extraction of numerical indices from the images was reported for the first time by Moriano and Alamprese13.
Therefore, the protocol here proposed, based on the work by Moriano and Alamprese13, illustrates a simple CVS that can be applied to support the already existing gravitational methodology for the study of ice cream melting behavior. A block diagram of the proposed method is illustrated in Figure 1. The use of such a system allows the calculation of two melting indices related to shape retention and the melting rate. In particular, the paper describes for the first time the detailed experimental setup and procedure for digital image acquisition during ice cream meltdown and the image processing steps. Besides, the results obtained from ice creams produced with different sweeteners (i.e., sucrose, sucromalt, and erythritol) are reported to show the potential of the method.
<img alt="Figure 1" class="xfigimg" src="/files/ftp_upload/66114/66114fig01.jpg" /> 
Figure 1: Block diagram of the proposed methodologies. Summary of the general steps for the proposed Computer Vision System and the gravimetric method for studying ice cream melting behavior. <a href="https://www.jove.com/files/ftp_upload/66114/66114fig01large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>

<meta charset="utf8"></head><body>Författare i fokus: Innovativ analys av smältande beteende hos glass genom ett system för datorseende

Ett datorseendesystem för bedömning av smältbeteende hos glass

This research aims to propose a computer vision system procedure to study one of the most important features of ice cream, which is the melting behavior. Usually, melting behavior is studied by a gravimetric approach, giving information about the initial time of melting and the rate of melting. However, the aspect of the product during melting is also very important, and this method calculates a couple of indexes related to the shape and size retention of ice cream during the meltdown.The advantage of using a computer vision system in the ice cream melting evaluation relies on the increased sensitivity in detecting small variations compared to the gravimetric method, and on the possibility to elaborate data related to the visual appearance of the product during meltdown. The computer vision system approach here proposed can be easily applied to other food products for which the melting rate and shape retention index are important, such as mousses and foams like whipped milk cream and egg albumin. These can lead to a better understanding of the meltdown mechanism, which is related to different factors.

Experimentell uppställning och procedur för smältningsförsök med glass

experimental-setup-and-procedure-for-ice-cream-melting-trials

Research

JoVE Journal

Engineering

Experimental Setup and Procedure for Ice Cream Melting Trials

257 Views. To begin, select transparent cups with fixed volume and shape, each equipped with a lid. Cut two strips of baking paper, each about two-centimeters wide. Using paper tape, attach these strips inside the cup walls, forming a cross at the bottom.Fill the cup with ice cream using a spatula. Once full, smooth the surface of the ice cream with the spatula, and seal the cup with its lid. Store the prepared sample at 30 degrees Celsius for at least 24 hours.Then condition the sample at...

Video: Experimental Setup and Procedure for Ice Cream Melting Trials

minimal erythema dose (med) testing

Minimal Erythema Dose MED Testing

This article describes how to conduct minimal erythema dose (MED) testing in order to determine the lowest dose of ultraviolet radiation that will cause erythema (burning) when administered to an...

Minimal Erythema Dose (MED) Testing

genotyping of staphylococcus aureus by ribosomal spacer pcr (rs-pcr)

Genotyping of Staphylococcus aureus by Ribosomal Spacer PCR RS-PCR

Here, ribosomal spacer PCR (RS-PCR) is used together with a miniaturized electrophoresis system as a fast and high resolution method for genotyping S. aureus at moderate costs allowing a high...

Genotyping of Staphylococcus aureus by Ribosomal Spacer PCR (RS-PCR)

an r-based landscape validation of a competing risk model

An R-Based Landscape Validation of a Competing Risk Model

The present protocol describes codes in R for evaluating the discrimination and calibration abilities of a competing risk model, as well as codes for the internal and external validation of...

r-loop analysis by dot-blot

R-Loop Analysis by Dot-Blot

This protocol details a simple method that quantifies R-loop, a three-stranded nucleic acid structure that comprises of an RNA-DNA hybrid and a displaced DNA...

proliferation and differentiation of murine myeloid precursor 32d/g-csf-r cells

Proliferation and Differentiation of Murine Myeloid Precursor 32D/G-CSF-R Cells

Here detailed protocols for culturing the murine myeloid precursor 32D/G-CSF-R cell line, performing viral infections, and carrying out proliferation and differentiation assays are presented. This cell line is suitable for studying myeloid cell development, and the role of genes of interest in myeloid cell growth and neutrophilic...

production of synthetic nuclear melt glass

Production of Synthetic Nuclear Melt Glass

A protocol for the production of synthetic nuclear melt glass, similar to trinitite, is...

customizing a cryolite glass prosthetic eye

Customizing a Cryolite Glass Prosthetic Eye

This manuscript shows each step of customizing a cryolite glass prosthetic eye including some major advantages of the use of cryolite glass for manufacturing an eye prosthesis compared to poly(methyl methacrylate). In addition, this manuscript gives ophthalmologists better insight into the ocularistic care that could improve interprofessional...

fabricating optical-quality glass surfaces to study macrophage fusion

Fabricating Optical-quality Glass Surfaces to Study Macrophage Fusion

This protocol describes the fabrication of optical-quality glass surfaces adsorbed with compounds containing long-chain hydrocarbons that can be used to monitor macrophage fusion of living specimens and enables super-resolution microscopy of fixed...

measuring cation transport by na,k- and h,k-atpase in xenopus oocytes by atomic absorption spectrophotometry: an alternative to radioisotope assays

Measuring Cation Transport by Na,K- and H,K-ATPase in Xenopus Oocytes by Atomic Absorption Spectrophotometry: An Alternative to Radioisotope Assays

We describe a method to quantify the activity of K+-countertransporting P-type ATPases by heterologous expression of the enzymes in Xenopus oocytes and measuring Rb+ or Li+ uptake into individual cells by atomic absorption spectrophotometry. The method is a sensitive and safe alternative to radioisotope flux experiments facilitating complex kinetic...

Measuring Cation Transport by Na,K- and H,K-ATPase in Xenopus Oocytes by Atomic Absorption Spectrophotometry: An Alternative to Radioisotope Assays

use of single molecule fluorescent in situ hybridization (sm-fish) to quantify and localize mrnas in murine oocytes

Use of Single Molecule Fluorescent In Situ Hybridization SM-FISH to Quantify and Localize mRNAs in Murine Oocytes

To reproducibly count the numbers of mRNAs in individual oocytes, single molecule RNA fluorescence in situ hybridization (RNA-FISH) was optimized for non-adherent cells. Oocytes were collected, hybridized with the transcript specific probes, and quantified using an image quantification...

Use of Single Molecule Fluorescent In Situ Hybridization (SM-FISH) to Quantify and Localize mRNAs in Murine Oocytes

measuring protein binding to f-actin by co-sedimentation

Measuring Protein Binding to F-actin by Co-sedimentation

This protocol describes a method to test the ability of a protein to co-sediment with filamentous actin (F-actin) and, if binding is observed, to measure the affinity of the...

use of electron paramagnetic resonance in biological samples at ambient temperature and 77 k

Use of Electron Paramagnetic Resonance in Biological Samples at Ambient Temperature and 77 K

Electron paramagnetic resonance (EPR) spectroscopy is an unambiguous method to measure free radicals. The use of selective spin probes allows for detection of free radicals in different cellular compartments. We present a practical, efficient method to collect biological samples that facilitate treating, storing, and transferring samples for EPR...

in vitro polymerization of f-actin on early endosomes

In Vitro Polymerization of F-actin on Early Endosomes

Early endosome functions depend on F-actin polymerization. Here, we describe a microscopy-based in vitro assay that reconstitutes the nucleation and polymerization of F-actin on early endosomal membranes in test tubes, thus rendering this complex series of reactions amenable to biochemical and genetic...

In Vitro Polymerization of F-actin on Early Endosomes

precision implementation of minimal erythema dose (med) testing to assess individual variation in human inflammatory response

Precision Implementation of Minimal Erythema Dose MED Testing to Assess Individual Variation in Human Inflammatory Response

Minimal erythema dose (MED) testing is used to establish dosage schedules for ultraviolet radiation phototherapy. It can assess individual variation in inflammatory response but lacks methodology for achieving reproducible results. Here, we present a precision implementation of MED and demonstrate its ability to capture individual variation in inflammatory...

Precision Implementation of Minimal Erythema Dose (MED) Testing to Assess Individual Variation in Human Inflammatory Response

mapping r-loops and rna:dna hybrids with s9.6-based immunoprecipitation methods

Mapping R-Loops and RNA:DNA Hybrids with S9.6-Based Immunoprecipitation Methods

R-loops constitute a prevalent class of transcription-driven non-B DNA structures that occur in all genomes depending on both DNA sequence and topological favorability. In recent years, R-loops have been implicated in a variety of adaptive and maladaptive roles and have been linked to genomic instability in the context of human disorders. As a consequence, the accurate mapping of these structures in genomes is of high interest to many investigators. DRIP-seq (DNA:RNA Immunoprecipitation...

labeling f-actin barbed ends with rhodamine-actin in permeabilized neuronal growth cones

Labeling F-actin Barbed Ends with Rhodamine-actin in Permeabilized Neuronal Growth Cones

A method to visualize and quantify F-actin barbed ends in neuronal growth cones is described. After culturing neurons on glass coverslips, cells are permeabilized with a saponin-containing solution. Then, a short incubation with the saponin buffer containing rhodamine-actin incorporates fluorescent actin onto free actin barbed...

live cell imaging of f-actin dynamics via fluorescent speckle microscopy (fsm)

Live Cell Imaging of F-actin Dynamics via Fluorescent Speckle Microscopy FSM

Selection, microinjection, and imaging of fluorescently-labeled F-actin via fluorescent speckle microscopy (FSM).

Live Cell Imaging of F-actin Dynamics via Fluorescent Speckle Microscopy (FSM)

implanting glass spinal cord windows in adult mice with experimental autoimmune encephalomyelitis

Implanting Glass Spinal Cord Windows in Adult Mice with Experimental Autoimmune Encephalomyelitis

We describe a method for implanting and maintaining glass windows over the exposed spinal cords of adult mice for studying experimental autoimmune encephalomyelitis. These windows provide chronic optical access to the spinal cord for monitoring cell dynamics at the subcellular level in live animals using two-photon...

study of the functions and activities of neuronal k-cl co-transporter kcc2 using western blotting

Study of the Functions and Activities of Neuronal K-Cl Co-Transporter KCC2 Using Western Blotting

The present protocol highlights the application of western blotting technique to study the functions and activities of neuronal K-Cl co-transporter KCC2. The protocol describes the investigation of KCC2 phosphorylation at kinase regulatory sites Thr906/1007 via western blotting. Also, additional methods to confirm KCC2 activity are briefly highlighted in this...

quantification of filamentous actin (f-actin) puncta in rat cortical neurons

Quantification of Filamentous Actin F-actin Puncta in Rat Cortical Neurons

Filamentous actin (F-actin) plays an important role in spinogenesis, synaptic plasticity, and synaptic stability. Quantification of F-actin puncta is therefore a useful tool to study the integrity of synaptic structures. This protocol describes the procedures of quantifying F-actin puncta labeled with Phalloidin in low-density primary cortical neuronal...

Quantification of Filamentous Actin (F-actin) Puncta in Rat Cortical Neurons

A Computer Vision System for the Assessment of Ice Cream Melting Behavior

Melting behavior is one of the most important quality indices of ice cream. It is usually evaluated by gravimetric methods and expressed in terms of starting time and rate of melting. However, the aspect of ice cream during melting is also important because shape retention is linked to a good structure of the product. The protocol proposed here illustrates a computer vision system (CVS) that can be used to support the already existing gravitational methodology to calculate two new melting indices related to shape retention and melting rate. Pictures of ice cream during melting are taken every 15 min for a total of 90 min. Afterward, digital images are elaborated using a purposely developed image processing method to calculate ice cream area, height, and width. The ratio between height and width at each melting time, referred to&#160;the ratio at time 0 (Rt/R0), is an index of the shape retention of ice cream, while the area at the different melting times referred to the area at time 0 (At/A0) is related to the melting rate. This computer vision system allows the obtaining of highly sensitive and reliable results, and it can be applied not only to ice cream but also to different food matrices, such as whipped milk cream or egg albumen.

Here, we present a protocol based on a computer vision system (CVS) to determine the melting behavior of multi-phase food systems.

Melting behavior is one of the most important quality indices of ice cream. It is usually evaluated by gravimetric methods and expressed in terms of ...

To begin, select transparent cups with fixed volume and shape, each equipped with a lid. Cut two strips of baking paper, each about two-centimeters wide. Using paper tape, attach these strips inside the cup walls, forming a cross at the bottom.Fill the cup with ice cream using a spatula. Once full, smooth the surface of the ice cream with the spatula, and seal the cup with its lid. Store the prepared sample at 30 degrees Celsius for at least 24 hours.Then condition the sample at 16 degrees Celsius for 24 hours before analysis. For the melting trial, set a thermostatic cabinet to approximately 20 degrees Celsius. Place a digital scale inside the cabinet.Connect the scale to a computer with software to record weight as a function of time. Next, position a graduated cylinder on the scale and reset the weight. Place a hanging funnel over the cylinder to collect melted ice cream.Set up a camera on a tripod in front of the cabinet, ensuring the best framing for sample images. Then prepare a metal wire mesh screen with a size reference. Remove the ice cream cup from the freezer and detach the ice cream from the cup walls Using a spatula, keeping the baking paper attached gently place it on the wire mesh screen, then remove the baking paper strips.Position the screen with the ice cream on the funnel inside the cabinet. Capture the initial image with the open cabinet door, including the size reference. Record data for 90 minutes, and take pictures of the ice cream every 15 minutes.Using this protocol, melting trials were performed for the three ice cream samples with different sweeteners, such as sucrose, sucromalt, and erythritol. While all samples showed good shape retention after 90 minutes, the lowest melting rate was observed for the ice cream made with erythritol.

Melting Index Calculation and Gravimetric Analysis of Ice Cream Melting 

To begin, download the images of melting ice cream captured by the digital camera setup to a computer. Then, in the image analysis software, click on File and Open to open the ice cream images. Start processing the first image and click on Edit and Rotate to adjust its rotation if necessary.Then, zoom into the size reference and click on Measure, then Calibration, followed by Spatial. Next, click on Image to spatially calibrate the image. Move the scale over the size reference and calibrate the length to convert pixels to millimeters.Next, click Edit, NEW AOI, and rectangular to select a rectangular area of interest that includes the ice cream sample avoiding the edge of the metal wire mesh screen. Crop this area and convert it to grayscale by clicking Edit, then Convert To and selecting Gray Scale. To apply the best fit filter, click on Enhance, then Equalize and Best Fit to automatically adjust brightness and contrast.Then, open the Measure and Count/Size window and set the parameters of Area, Box Height and Box Width. Choose manual measurement in the Count/Size window and click on Select Ranges to set the histogram values to segment the bright shape of the ice cream. After closing the Segmentation window, click on Count in the Count/Size window of the software to measure the parameters.View the results by clicking on View and Measurement Data. Then click on File and Data to Clipboard to copy these results and paste them into a data management software spreadsheet To evaluate the melting index, use this equation on the H and W data at different melting times to calculate the shape retention index. Refer R and A data at each time point to the corresponding index at time zero, and plot these results over time according to these equations.For gravimetric data analysis, save the spreadsheet with the weight of the melted sample per minute. At the end of the 90-minute melting trial, open this spreadsheet in data management software to create a melting curve showing the melted weight over time. Select data from the linear portion of the melting curve to calculate the least squares regression line and the regression coefficient.The slope of this line represents the ice cream melting rate in grams per minute. Calculate the starting time of melting as the x-intercept where y is zero. Using this protocol, melting behavior was analyzed for ice creams made with different sweeteners such as sucrose, sucromalt, and erythritol.Shape retention curves showed that ice cream made with sucrose lost its shape faster than the others, whereas the ice cream made with erythritol kept its shape until the end of the trial. Similarly, area retention curves showed that ice cream containing erythritol showed a lower meltdown rate compared to ice creams with sucromalt and sucrose. Further, gravimetric analysis showed that the ice cream containing erythritol showed the highest melting starting time and lowest melting rate out of the three samples.