Name: collection and extraction of occupational air samples for analysis of fungal dna
Uploaded: 2018-05-02T13:00:00
Description: Watch this Scientific Journal Video about Collection and Extraction of Occupational Air Samples for Analysis of Fungal DNA at JoVE.com

This work was supported in part by an interagency agreement between NIOSH and NIEHS (AES12007001-1-0-6).

1. Preparing the NIOSH aerosol sampler
NOTE: The NIOSH aerosol sampler is a two-stage cyclone aerosol sampler that collects bioaerosols using two sampling tubes and a polytetrafluoroethylene (PTFE) filter.
<ol>
	<li>Before assembly, carefully inspect the sampler. Check the sampler to ensure it is not damaged, all screws are in place and snug, and the sealing tape around the seam formed by the two halves is intact. Inspect the sampler O-ring to ensure it does not have any nicks, cracks or tea...

<ol>
	<li>Mendell, M. J., Mirer, A. G., Cheung, K., Tong, M., Douwes, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Respiratory+and+allergic+health+effects+of+dampness,+mold,+and+dampness-related+agents:+a+review+of+the+epidemiologic+evidence.">Respiratory and allergic health effects of dampness, mold, and dampness-related agents: a review of the epidemiologic evidence.</a> Environ Health Perspect. 119 (6), 748-756 (2011).</li><li>Green, B. J., Lemons, A. R., Park, Y., Cox-Ganser, J. M., Park, J. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Assessment+of+fungal+diversity+in+a+water-damaged+office+building.">Assessment of fungal diversity in a water-damaged office building.</a> J Occup Environ Hyg. 14 (4), 285-293 (2017).</li><li>Green, B. J., Lemons, A. R., Park, Y., Cox-Ganser, J. M., Park, J. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Assessment+of+fungal+diversity+in+a+water-damaged+office+building.">Assessment of fungal diversity in a water-damaged office building.</a> J Occup Environ Hyg. , (2016).</li><li>Pitkaranta, M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Analysis+of+fungal+flora+in+indoor+dust+by+ribosomal+DNA+sequence+analysis,+quantitative+PCR,+and+culture.">Analysis of fungal flora in indoor dust by ribosomal DNA sequence analysis, quantitative PCR, and culture.</a> Appl Environ Microbiol. 74 (1), 233-244 (2008).</li><li>Rittenour, W. R., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Internal+transcribed+spacer+rRNA+gene+sequencing+analysis+of+fungal+diversity+in+Kansas+City+indoor+environments.">Internal transcribed spacer rRNA gene sequencing analysis of fungal diversity in Kansas City indoor environments.</a> Environ Sci Process Impacts. 16 (1), 33-43 (2014).</li><li>Martin, K. J., Rygiewicz, P. T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Fungal-specific+PCR+primers+developed+for+analysis+of+the+ITS+region+of+environmental+DNA+extracts.">Fungal-specific PCR primers developed for analysis of the ITS region of environmental DNA extracts.</a> BMC Microbiol. 5, 28 (2005).</li><li>Monard, C., Gantner, S., Stenlid, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Utilizing+ITS1+and+ITS2+to+study+environmental+fungal+diversity+using+pyrosequencing.">Utilizing ITS1 and ITS2 to study environmental fungal diversity using pyrosequencing.</a> FEMS Microbiol Ecol. 84 (1), 165-175 (2013).</li><li>Op De Beeck, M., Lievens, B., Busschaert, P., Declerck, S., Vangronsveld, J., Colpaert, J. V. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Comparison+and+validation+of+some+ITS+primer+pairs+useful+for+fungal+metabarcoding+studies.">Comparison and validation of some ITS primer pairs useful for fungal metabarcoding studies.</a> PLoS One. 9 (6), e97629 (2014).</li><li>Toju, H., Tanabe, A. S., Yamamoto, S., Sato, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=High-coverage+ITS+primers+for+the+DNA-based+identification+of+ascomycetes+and+basidiomycetes+in+environmental+samples.">High-coverage ITS primers for the DNA-based identification of ascomycetes and basidiomycetes in environmental samples.</a> PLoS One. 7 (7), e40863 (2012).</li><li>Lemons, A. R., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Microbial+rRNA+sequencing+analysis+of+evaporative+cooler+indoor+environments+located+in+the+Great+Basin+Desert+region+of+the+United+States.">Microbial rRNA sequencing analysis of evaporative cooler indoor environments located in the Great Basin Desert region of the United States.</a> Environ Sci Process Impacts. , (2017).</li><li>Cao, G., Noti, J. D., Blachere, F. M., Lindsley, W. G., Beezhold, D. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Development+of+an+improved+methodology+to+detect+infectious+airborne+influenza+virus+using+the+NIOSH+bioaerosol+sampler.">Development of an improved methodology to detect infectious airborne influenza virus using the NIOSH bioaerosol sampler.</a> J Environ Monit. 13 (12), 3321-3328 (2011).</li><li>Soo, J. C., Lee, T., Kashon, M., Kusti, M., Harper, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Quartz+in+coal+dust+deposited+on+internal+surface+of+respirable+size+selective+samplers.">Quartz in coal dust deposited on internal surface of respirable size selective samplers.</a> J Occup Environ Hyg. 11 (12), D215-D219 (2014).</li><li>Wang, C. H., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Field+evaluation+of+personal+sampling+methods+for+multiple+bioaerosols.">Field evaluation of personal sampling methods for multiple bioaerosols.</a> PLoS One. 10 (3), e0120308 (2015).</li><li>Lindsley, W. G., Schmechel, D., Chen, B. T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+two-stage+cyclone+using+microcentrifuge+tubes+for+personal+bioaerosol+sampling.">A two-stage cyclone using microcentrifuge tubes for personal bioaerosol sampling.</a> J Environ Monit. 8 (11), 1136-1142 (2006).</li><li>Rittenour, W. R., Park, J. H., Cox-Ganser, J. M., Beezhold, D. H., Green, B. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Comparison+of+DNA+extraction+methodologies+used+for+assessing+fungal+diversity+via+ITS+sequencing.">Comparison of DNA extraction methodologies used for assessing fungal diversity via ITS sequencing.</a> J Environ Monit. 14 (3), 766-774 (2012).</li><li>ACGIH. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Documentation of the threshold limit values and biological exposure indices. Appendix C: Particle size-selective sampling criteria for airborne particulate matter. , (2001).</li><li>Rodes, C. E., Thornburg, J. W., Ruzer, L. S., Harley, N. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Aerosols handbook: measurement, dosimetry, and health effects. , (2005).</li><li>Broadwater, K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Investigating+a+persistent+odor+at+an+aircraft+seat+manufacturer.">Investigating a persistent odor at an aircraft seat manufacturer.</a> J Occup Environ Hyg. 13 (10), D159-D165 (2016).</li><li>Couch, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Health Hazard Evaluation Program: Evaluation of Potential Hazards during Harvesting and Processing Cannabis at an Outdoor Organic Farm. Report No. 2015-0111-3271. , (2017).</li><li>Feinstein, L. M., Sul, W. J., Blackwood, C. B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Assessment+of+bias+associated+with+incomplete+extraction+of+microbial+DNA+from+soil.">Assessment of bias associated with incomplete extraction of microbial DNA from soil.</a> Appl Environ Microbiol. 75 (16), 5428-5433 (2009).</li><li>Keswani, J., Kashon, M. L., Chen, B. T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Evaluation+of+interference+to+conventional+and+real-time+PCR+for+detection+and+quantification+of+fungi+in+dust.">Evaluation of interference to conventional and real-time PCR for detection and quantification of fungi in dust.</a> J Environ Monit. 7 (4), 311-318 (2005).</li><li>Bellemain, E., Carlsen, T., Brochmann, C., Coissac, E., Taberlet, P., Kauserud, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=ITS+as+an+environmental+DNA+barcode+for+fungi:+an+in+silico+approach+reveals+potential+PCR+biases.">ITS as an environmental DNA barcode for fungi: an in silico approach reveals potential PCR biases.</a> BMC Microbiol. 10, 189 (2010).</li><li>Farrelly, V., Rainey, F. A., Stackebrandt, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Effect+of+genome+size+and+rrn+gene+copy+number+on+PCR+amplification+of+16S+rRNA+genes+from+a+mixture+of+bacterial+species.">Effect of genome size and rrn gene copy number on PCR amplification of 16S rRNA genes from a mixture of bacterial species.</a> Appl Environ Microbiol. 61 (7), 2798-2801 (1995).</li><li>Vesper, S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Development+of+an+Environmental+Relative+Moldiness+index+for+US+homes.">Development of an Environmental Relative Moldiness index for US homes.</a> J Occup Environ Med. 49 (8), 829-833 (2007).</li></ol>

Determining the fungal diversity within an occupational environment using sequencing-based approaches has improved fungal hazard identification and exposure assessment. Using this approach has allowed for the detection of many additional fungal species that are often not detected using culture or microscopy-based methods of assessment. A method for sampling bioaerosols from occupational and indoor environments and the extraction of genomic DNA from air samples for ITS amplification and sequencing is presented here. Deter...

Fungal exposures in indoor and occupational environments can result in respiratory morbidities, including allergic sensitization and asthma1. Identification of fungal hazards is important for assessing risk and preventing worker exposure. These fungal hazards may be a result of indoor contamination, outdoor air intrusion, or environmental disturbances that result in the transport of fungal materials into areas where workers are present2. Methods to assess fungal exposure have included viable culture sampling as well as microscopic identification of fungal spores. These approaches have several limitations and often overlook many fungal species that could be contributing to the overall fungal burden3. Culture-based approaches can only differentiate those viable fungal organisms that can be cultivated on nutrient media. Identifying fungal spores to species level via microscopy can be confounded by spores sharing similar morphologies. Both methods are highly dependent on mycologists to analyze and identify the fungal species, with many remaining unidentified.
To improve upon existing methodologies used in occupational hazard identification and exposure assessments, many researchers have turned to molecular-based technologies. Sequencing-based approaches for assessing microbial diversity within indoor and occupational environments have revealed a broader spectrum of fungal species encountered compared to methods such as microscopy and viable culture3,4,5. The method presented here describes the air sampling of occupational environments and extraction of genomic DNA for the identification of potential fungal hazards. Hazard identification is accomplished by sequencing the nuclear ribosomal internal transcribed spacer, or ITS, regions that are highly variable among fungi and have been commonly used to differentiate fungal species6,7,8,9. Many species found in occupational settings, such as some species belonging to the phylum Basidiomycota, are not identifiable in viable culture and are difficult to differentiate microscopically. These fungi have been observed in high relative abundance within indoor and occupational environments assessed by sequencing fungal ITS regions3,4,10. ITS sequencing has provided greater knowledge into the diversity of fungi encountered within indoor and occupational environments.
The protocol described here details the methods used to collect, extract, and amplify fungal ITS regions from bioaerosols for sequence analysis. This approach utilizes the National Institute for Occupational Safety and Health (NIOSH) two-stage cyclone aerosol sampler to collect particulates in the air. This sampler was developed to collect bioaerosols and separate respirable (&#8804;4 &#181;m aerodynamic diameter) and non-respirable (&#62;4 &#181;m aerodynamic diameter) particles, which allows for identification of fungal organisms within indoor environments that are most likely to be inhaled by a worker11. Other air samplers, including cyclone samplers, are available on the market that have the ability to collect particles within the respirable range (&#60;4 &#181;m) using filters12,13. In contrast, the NIOSH two-stage cyclone aerosol sampler separates fungal species based on their aerodynamic diameter into disposable, polypropylene tubes that can be immediately processed for downstream applications14.
The processes of extracting genomic DNA and amplifying the fungal ITS regions are detailed in this protocol. The extraction methodologies presented have been developed specifically for the extraction of genomic DNA from fungi and bacteria, as many commercial kits target mammalian cells, bacteria, or specifically yeasts15. The primers used in this study are selected based on their overall coverage of both the fungal ITS 1 and ITS 2 regions4,5. Sequencing of these regions allows for the comparison of many banked ITS sequences, including those that sequence the ITS 1 region, the ITS 2 region, or both the ITS 1 and ITS 2 regions. The fungal diversity of air samples collected in an indoor setting using these methods are shown, revealing a substantial number of sequences placed in the phyla Ascomycota and Basidiomycota as well as other sequences belonging to less dominant fungal phyla, such as Zygomycota. The broad diversity of fungal sequences identified using this approach would not be captured using traditional hazard identification methodologies like cultivation or microscopy. Sequencing of fungal ITS regions provides an enhanced method to identify fungal hazards and allow for a better understanding of indoor and occupational fungal exposures.

<table>
	<tbody>
		<tr>
			<td>NIOSH BC251 bioaerosol cyclone sampler</td>
			<td>NIOSH</td>
			<td>BC251</td>
			<td>The NIOSH sampler is not yet commercially available. Please contact William Lindsley, PhD (wlindsley@cdc.gov) for information on obtaining the NIOSH sampler</td>
		</tr>
		<tr>
			<td>Fisherbrand Sterile Microcentrifuge Tubes with Screw Caps</td>
			<td>Fisher Scientific</td>
			<td>02-681-373</td>
			<td>1.5 mL polypropylene microcentrifuge tubes for air sampling; screw top threading must match the threading of the NIOSH sampler</td>
		</tr>
		<tr>
			<td>Falcon 15 mL Conical Centrifuge Tubes</td>
			<td>Corning</td>
			<td>352096</td>
			<td>15 mL polypropylene tubes for air sampling</td>
		</tr>
		<tr>
			<td>Clean Room Vinyl Tape, Easy-Remove, 1/4&#34; Width</td>
			<td>McMaster-Carr</td>
			<td>76505A1</td>
			<td>sealing tape</td>
		</tr>
		<tr>
			<td>Filter Cassette, Clear Styrene, 37 mm</td>
			<td>SKC Inc.</td>
			<td>225-3LF</td>
			<td>3-piece sampling cassette (no filter). Contains: cassette base, extension cowl, cassette cap and inlet/outlet plugs</td>
		</tr>
		<tr>
			<td>PTFE hydrophobic fluoropore membrane filters, 3.0 &#181;m, 37 mm</td>
			<td>EMD Millipore</td>
			<td>FSLW03700</td>
			<td>Contains: 37 mm, 3.0 &#181;m PTFE filters and support pads</td>
		</tr>
		<tr>
			<td>Fisherbrand filter forceps</td>
			<td>Fisher Scientific</td>
			<td>09-753-50</td>
			<td>filter forceps</td>
		</tr>
		<tr>
			<td>Model 502 Precision PanaPress</td>
			<td>PanaVise</td>
			<td>502</td>
			<td>pneumatic cassette press is constructed from this precision arbor press</td>
		</tr>
		<tr>
			<td>Scotch Super 33+ vinyl electrical tape</td>
			<td>McMaster-Carr</td>
			<td>76455A21</td>
			<td>19 mm tape</td>
		</tr>
		<tr>
			<td>Multi-purpose Calibration Jar, Large</td>
			<td>SKC Inc.</td>
			<td>225-112</td>
			<td>calibration jar</td>
		</tr>
		<tr>
			<td>Universal PCXR4 Sample Pump</td>
			<td>SKC Inc.</td>
			<td>224-PCXR4</td>
			<td>sampling pump</td>
		</tr>
		<tr>
			<td>Mass Flowmeter 4140</td>
			<td>TSI Inc.</td>
			<td>4140</td>
			<td>flow meter</td>
		</tr>
		<tr>
			<td>Roche High Pure PCR Template Kit</td>
			<td>Roche Diagnostics</td>
			<td>11796828001</td>
			<td>Kit used for genomic DNA extraction. Contains: Lysis buffer, Binding buffer, Proteinase K, Inhibitor removal buffer, Wash buffer, Elution buffer, Glass fiber filter tubes and 2 ml collection tubes</td>
		</tr>
		<tr>
			<td>Fisherbrand 2 mL Reinforced Polypropylene Screw Cap Tubes with Caps</td>
			<td>Fisher Scientific</td>
			<td>15340162</td>
			<td>2 mL reinforced tubes for bead homogenization</td>
		</tr>
		<tr>
			<td>Glass beads, acid washed, 212-300 &#181;m</td>
			<td>Sigma-Aldrich</td>
			<td>G1277</td>
			<td>glass beads</td>
		</tr>
		<tr>
			<td>Fisher Scientific Bead Mill 24 Homogenizer</td>
			<td>Fisher Scientific</td>
			<td>15-340-163</td>
			<td>bead homogenizer</td>
		</tr>
		<tr>
			<td>CelLytic B Cell Lysis Reagent, 10X</td>
			<td>Sigma-Aldrich</td>
			<td>C8740</td>
			<td>lysis reagent</td>
		</tr>
		<tr>
			<td>Platinum Taq polymerase</td>
			<td>Invitrogen</td>
			<td>10966-018</td>
			<td>Contains: Platinum Taq polymerase, 10X PCR buffer (no MgCl2), 50 mM MgCl2, KB Extender</td>
		</tr>
		<tr>
			<td>dNTP Mix</td>
			<td>Invitrogen</td>
			<td>18427-088</td>
			<td>10 mM dNTP mix</td>
		</tr>
		<tr>
			<td>QIAquick PCR Purification Kit</td>
			<td>Qiagen</td>
			<td>28106</td>
			<td>Kit used to purify fungal amplicons. Contains: Buffer PB (binding buffer), Buffer PE (washing buffer), Buffer EB (elution buffer), pH Indicator dye (optional), and GelPilot loading dye</td>
		</tr>
		<tr>
			<td>Owl EasyCast Mini Gel Electrophoresis System</td>
			<td>Thermo Fisher</td>
			<td>B1 or B2</td>
			<td></td>
		</tr>
		<tr>
			<td>TrackIt 1 KB Plus DNA Ladder</td>
			<td>Thermo Fisher</td>
			<td>10488-085</td>
			<td>DNA ladder</td>
		</tr>
	</tbody>
</table>

collection and extraction of occupational air samples for analysis of fungal dna

Traditional methods of identifying fungal exposures in occupational environments, such as culture and microscopy-based approaches, have several limitations that have resulted in the exclusion of many species. Advances in the field over the last two decades have led occupational health researchers to turn to molecular-based approaches for identifying fungal hazards. These methods have resulted in the detection of many species within indoor and occupational environments that have not been detected using traditional methods. This protocol details an approach for determining fungal diversity within air samples through genomic DNA extraction, amplification, sequencing, and taxonomic identification of fungal internal transcribed spacer (ITS) regions. ITS sequencing results in the detection of many fungal species that are either not detected or difficult to identify to species level using culture or microscopy. While these methods do not provide quantitative measures of fungal burden, they offer a new approach to hazard identification and can be used to determine overall species richness and diversity within an occupational environment.

The species distribution within an environment can be assessed using relative abundance by determining the number of clones of each OTU identified in the air samples. Figure 6 is a Krona chart representing the taxonomically placed species within an indoor environment following 60 min of air sampling. It can be observed that the environment contains a variety of species within two major fungal phyla, Ascomycota and Basidiomycota, as well as species belonging t...

Watch this Scientific Journal Video about Collection and Extraction of Occupational Air Samples for Analysis of Fungal DNA at JoVE.com

Collection and Extraction of Occupational Air Samples for Analysis of Fungal DNA

Determining the fungal diversity within an environment is a method utilized in occupational health studies to identify health hazards. This protocol describes DNA extraction from occupational air samples for amplification and sequencing of fungal ITS regions. This approach detects many fungal species that can be overlooked by traditional assessment methods.

Traditional methods of identifying fungal exposures in occupational environments, such as culture and microscopy-based approaches, have several ...

Research

Education

JoVE Journal

JoVE Core

Environment

Biology

Nursing

Ecology

Unit 1

Introduction to Health

Biodiversity and Conservation

SCIENTISTS IN ACTION

EPA Method 1615. Measurement of Enterovirus and Norovirus Occurrence in Water by Culture and RT-qPCR. I. Collection of Virus Samples

엔테로 바이러스 및 문화 RT-qPCR에 의해 물에서 노로 바이러스의 발생의 EPA 방법 1615 측정. 바이러스 샘플의 I. 컬렉션

EPA Method 1615 was developed with a goal of providing a standard method for measuring enteroviruses and noroviruses in environmental and drinking waters. ...

연구

환경과학

A Simple Method for Automated Solid Phase Extraction of Water Samples for Immunological Analysis of Small Pollutants

작은 오염 물질의 면역 학적 분석을위한 물 샘플의 자동화 된 고체상 추출을위한 간단한 방법

A new method for solid phase extraction (SPE) of environmental water samples is proposed. The developed prototype is cost-efficient and user friendly, and ...

Air-sampled Filter Analysis for Endotoxins and DNA Content

독소와 DNA 내용에 대한 공기 샘플링 필터 분석

Outdoor aerosol research commonly uses particulate matter sampled on filters. This procedure enables various characterizations of the collected particles ...

Simultaneous DNA-RNA Extraction from Coastal Sediments and Quantification of 16S rRNA Genes and Transcripts by Real-time PCR

실시간 PCR에 의한 연안 퇴적물 및 정량 16S의 rRNA의 유전자 및 성적 증명서에서 동시 DNA-RNA 추출

Real Time Polymerase Chain Reaction also known as quantitative PCR (q-PCR) is a widely used tool in microbial ecology to quantify gene abundances of ...

Extraction and Analysis of Microbial Phospholipid Fatty Acids in Soils

추출 및 토양의 미생물 인지질 지방산의 분석

Phospholipid fatty acids (PLFAs) are key components of microbial cell membranes. The analysis of PLFAs extracted from soils can provide information about ...

Modification and Application of a Leaf Blower-vac for Field Sampling of Arthropods

수정 및 절지 동물의 필드 샘플링을위한 잎 송풍기 - 진공 청소기의 적용

Rice fields host a large diversity of arthropods, but investigating their population dynamics and interactions is challenging. Here we describe the ...

Use of a Filter Cartridge for Filtration of Water Samples and Extraction of Environmental DNA

여과 물 샘플 및 환경 DNA의 추출을위한 필터 카트리지의 사용

Recent studies demonstrated the use of environmental DNA (eDNA) from fishes to be appropriate as a non-invasive monitoring tool. Most of these studies ...

Automated, High-resolution Mobile Collection System for the Nitrogen Isotopic Analysis of NOx

Automated, High-resolution Mobile Collection System for the Nitrogen Isotopic Analysis of NOx

고해상도 모바일 콜렉션 시스템은 NO의 질소 동위 원소 분석, 자동화<sub&gt; X</sub

Nitrogen oxides (NOx = NO + NO2) are a family of atmospheric trace gases that have great impact on the environment. NOx concentrations directly influence ...

A Lipid Extraction and Analysis Method for Characterizing Soil Microbes in Experiments with Many Samples

많은 샘플을 이용한 실험에서 토양 미생물을 특성화하기위한 지질 추출 및 분석 방법

Microbial communities are important drivers and regulators of ecosystem processes. To understand how management of ecosystems may affect microbial ...

Extraction of Organochlorine Pesticides from Plastic Pellets and Plastic Type Analysis

플라스틱 펠렛 및 플라스틱 유형 분석에서 유기 염소 농약의 추출

Plastic resin pellets, categorized as microplastics (&#8804;5 mm in diameter), are small granules that can be unintentionally released to the environment ...