Name: fabrication of soft pneumatic network actuators with oblique chambers
Uploaded: 2018-08-17T14:30:00
Description: Watch this Scientific Journal Video about Fabrication of Soft Pneumatic Network Actuators with Oblique Chambers at JoVE.com

这项工作得到了中国国家自然科学基金授予51622506和上海市科技委员会授予16JC1401000 的支持。

注: 该协议提供了软气动网络执行器的制作程序。在制作过程之前, 一组模具和几个执行器-油管连接器, 这是设计的计算机辅助设计 (CAD) 软件必须提前3维打印。模具见图 1B。
1. 硅胶弹性体的制备
<ol><li>在同一混合容器 (图 2A) 中, 将5克的硅胶弹性体 B 和 45 g 部分 A (9:1 (A: B) 零件按重量) 称量。使用注射器?...

<ol>
	<li>Rus, D., Tolley, M. T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Design,+fabrication+and+control+of+soft+robots.">Design, fabrication and control of soft robots.</a> Nature. 521 (7553), 467-475 (2015).</li><li>Ilievski, F., Mazzeo, A. D., Shepherd, R. F., Chen, X., Whitesides, G. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Soft+robotics+for+chemists.">Soft robotics for chemists.</a> Angewandte Chemie International Edition. 50 (8), 1890-1895 (2011).</li><li>Shepherd, R. F., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Multigait+soft+robot.">Multigait soft robot.</a> Proceedings of the National Academy of Sciences of the United States of America. 108 (51), 20400-20403 (2011).</li><li>Yap, H. K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+fully+fabric-based+bidirectional+soft+robotic+glove+for+assistance+and+rehabilitation+of+hand+impaired+patients.">A fully fabric-based bidirectional soft robotic glove for assistance and rehabilitation of hand impaired patients.</a> IEEE Robotics and Automation Letters. 2 (3), 1383-1390 (2017).</li><li>Yang, Y., Chen, Y., Li, Y., Chen, M. Z. Q., Wei, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Bioinspired+Robotic+Fingers+Based+on+Pneumatic+Actuator+and+3D+Printing+of+Smart+Material.">Bioinspired Robotic Fingers Based on Pneumatic Actuator and 3D Printing of Smart Material.</a> Soft Robotics. 4 (2), 147-162 (2017).</li><li>Gu, G. Y., Zhu, J., Zhu, L. M., Zhu, X. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+survey+on+dielectric+elastomer+actuators+for+soft+robots.">A survey on dielectric elastomer actuators for soft robots.</a> Bioinspiration &amp; Biomimetics. 12 (1), 011003 (2017).</li><li>Holland, D. P., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+soft+robotics+toolkit:+Strategies+for+overcoming+obstacles+to+the+wide+dissemination+of+soft-robotic+hardware.">The soft robotics toolkit: Strategies for overcoming obstacles to the wide dissemination of soft-robotic hardware.</a> IEEE Robotics &amp; Automation Magazine. 24 (1), 57-64 (2017).</li><li>Galloway, K. C., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Soft+Robotic+Grippers+for+Biological+Sampling+on+Deep+Reefs.">Soft Robotic Grippers for Biological Sampling on Deep Reefs.</a> Soft Robotics. 3 (1), 23-33 (2016).</li><li>Polygerinos, P., Wang, Z., Galloway, K. C., Wood, R. J., Walsh, C. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Soft+robotic+glove+for+combined+assistance+and+at-home+rehabilitation.">Soft robotic glove for combined assistance and at-home rehabilitation.</a> Robotics and Autonomous Systems. 73, 135-143 (2015).</li><li>Tolley, M. T., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+Resilient,+Untethered+Soft+Robot.">A Resilient, Untethered Soft Robot.</a> Soft Robotics. 1 (3), 213-223 (2014).</li><li>Ainla, A., Verma, M. S., Yang, D., Whitesides, G. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Soft,+Rotating+Pneumatic+Actuator.">Soft, Rotating Pneumatic Actuator.</a> Soft Robotics. 4 (3), 297-304 (2017).</li><li>Koizumi, Y., Shibata, M., Hirai, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Rolling+tensegrity+driven+by+pneumatic+soft+actuators.">Rolling tensegrity driven by pneumatic soft actuators.</a> 2012 IEEE International Conference on Robotics and Automation (ICRA). , (2012).</li><li>Connolly, F., Polygerinos, P., Walsh, C. J., Bertoldi, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Mechanical+Programming+of+Soft+Actuators+by+Varying+Fiber+Angle.">Mechanical Programming of Soft Actuators by Varying Fiber Angle.</a> Soft Robotics. 2 (1), 26-32 (2015).</li><li>Connolly, F., Walsh, C. J., Bertoldi, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Automatic+design+of+fiber-reinforced+soft+actuators+for+trajectory+matching.">Automatic design of fiber-reinforced soft actuators for trajectory matching.</a> Proceedings of the National Academy of Sciences of the United States of America. 114 (1), 51-56 (2017).</li><li>Martinez, R. V., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Robotic+tentacles+with+three-dimensional+mobility+based+on+flexible+elastomers.">Robotic tentacles with three-dimensional mobility based on flexible elastomers.</a> Advanced Materials. 25 (2), 205-212 (2013).</li><li>Polygerinos, P., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Modeling+of+Soft+Fiber-Reinforced+Bending+Actuators.">Modeling of Soft Fiber-Reinforced Bending Actuators.</a> IEEE Transactions on Robotics. 31 (3), 778-789 (2015).</li><li>Mosadegh, B., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Pneumatic+Networks+for+Soft+Robotics+that+Actuate+Rapidly.">Pneumatic Networks for Soft Robotics that Actuate Rapidly.</a> Advanced Functional Materials. 24 (15), 2163-2170 (2014).</li><li>Wang, T., Ge, L., Gu, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Programmable+design+of+soft+pneu-net+actuators+with+oblique+chambers+can+generate+coupled+bending+and+twisting+motions.">Programmable design of soft pneu-net actuators with oblique chambers can generate coupled bending and twisting motions.</a> Sensors and Actuators A: Physical. 271, 131-138 (2018).</li><li>Marchese, A. D., Katzschmann, R. K., Rus, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+Recipe+for+Soft+Fluidic+Elastomer+Robots.">A Recipe for Soft Fluidic Elastomer Robots.</a> Soft Robotics. 2 (1), 7-25 (2015).</li></ol>

本文提出了一种用斜腔法指导软气动网络驱动器制作的方法协议。根据该协议, 一个执行器可以在3小时内独立制造。该议定书的关键步骤可归纳如下。(i) 硅胶弹性体是按比例和混合井配制而成的。(二) 将硅胶弹性体倒入模具中, 用于制造室部零件和底座。(iii) 暴露表面的气泡被刺穿, 暴露表面上的任何多余的硅胶弹性体被刮掉。(iv) 硅胶弹性体在烤箱中固化。(v) 两部分由硅胶弹性体粘合在一起。?...

软气动执行器 (spa) 是软的设备, 可以驱动的简单输入气压1,2。它们可以用不同的材料制造, 如硅胶弹性体3、织物4、形状记忆聚合物5和介电弹性6。研究人员从他们的依从性, 灵巧的动作, 和简单的制造方法7, 使温泉已成为最有希望的设备, 软机器人应用8,9。温泉可以实现各种复杂的运动, 如蠕动10, 旋转11, 和滚动12基于各种类型的变形, 包括扩展, 扩大, 弯曲, 扭曲13,14. 为了能够做出不同类型的运动, 温泉浴场设计在不同的结构中, 例如一个具有平行通道15的线性机构, 一个带有纤维增强16的单室, 以及重复的网络分庭17。其中, 带有重复分室网络的软气动网络执行器, 由于在较低的输入压力下能产生较大的变形, 因而得到了广泛的应用。然而, 在以前的大多数设计中, 这种类型的执行器只能产生2维空间的弯曲运动, 这极大地限制了它们的应用。
软气动网络执行器由一个由内部通道连接的线性排列的腔组组成。每立方室包含一对相对地比另一对更薄的对面墙壁, 并且在垂直于更薄的墙壁的方向产生双面通货膨胀。原来, 更薄的腔壁垂直于执行机构的长轴, 并随着长轴膨胀。这些共线通货膨胀在腔室和不可扩展的基板导致一个整体的纯弯曲的执行器。为了探索3维空间中执行器的运动, 调整腔的方向, 使较薄的侧壁不再垂直于执行器的长轴 (图 1A), 从而使每个腔室的膨胀方向从轴偏移并变为非共线。所有平行但非共线通货膨胀将执行器的运动改变为3维空间18的耦合弯曲和扭转运动。这种耦合的运动使执行器更灵活和灵巧, 使执行器一个合适的候选更实际的应用, 如灵活的机械手, 生物启发的机器人, 和医疗设备。
该协议说明了该类软气动网络驱动器的制造方法。它包括准备硅胶弹性体, 制造室和基部, 组装执行器, 连接油管, 检查泄漏, 并在必要时, 修复执行器。它还可用于制造正常的软气动网络执行器和其他软执行机构, 可以通过对成型方法的一些简单修改来制作。我们提供了详细的步骤, 以制造一个软的气动执行器与30°斜室。对于不同的应用, 不同腔角的执行机构可以根据相同的协议进行制造。此外, 执行机构可以结合起来, 形成一个多执行器系统的各种要求。

<table border="0" cellpadding="0" cellspacing="0" style="width:796px;" width="794">
	<colgroup>
		<col />
		<col />
		<col />
		<col />
	</colgroup>
	<tbody>
		<tr height="42">
			<td height="42" style="height:42px;width:207px;">Silicone elastomer</td>
			<td style="width:168px;">Wacker</td>
			<td style="width:135px;">ELASTOSIL M4601 A/B</td>
			<td style="width:287px;">Material of the actuators</td>
		</tr>
		<tr height="63">
			<td height="63" style="height:63px;width:207px;">Syringe&#160;</td>
			<td style="width:168px;">Shanghai Kindly Medical Instruments&#160;</td>
			<td style="width:135px;">10 ml</td>
			<td style="width:287px;">Used to inject silicone rubber into the hole of the mold for fabricating the connection end</td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:207px;">Precision scale</td>
			<td style="width:168px;">Shanghai Hochoice</td>
			<td style="width:135px;">UTP-313</td>
			<td style="width:287px;">Used to weigh the silicone rubber</td>
		</tr>
		<tr height="42">
			<td height="42" style="height:42px;width:207px;">Planetary centrifugal vacuum mixer</td>
			<td style="width:168px;">THINKY</td>
			<td style="width:135px;">ARE-310</td>
			<td style="width:287px;">Used to mix the silicone rubber and defoam after mixing process</td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:207px;">Release agent</td>
			<td style="width:168px;">Smooth-on</td>
			<td style="width:135px;">Release 200</td>
			<td style="width:287px;">Used for ease of demolding&#160;</td>
		</tr>
		<tr height="42">
			<td height="42" style="height:42px;width:207px;">Needle</td>
			<td style="width:168px;">Shanghai Kindly Medical Instruments&#160;</td>
			<td style="width:135px;"></td>
			<td style="width:287px;">Used for Piercing the bubbles form on the surface</td>
		</tr>
		<tr height="63">
			<td height="63" style="height:63px;width:207px;">Utility blade</td>
			<td style="width:168px;">M&#38;G Chenguang Stationery</td>
			<td style="width:135px;">ASS91325</td>
			<td style="width:287px;">Used for Scraping off excess silicone rubber along the upper surface of the mold&#160;</td>
		</tr>
		<tr height="42">
			<td height="42" style="height:42px;width:207px;">Vacuum oven</td>
			<td style="width:168px;">Ningbo SI Instrument</td>
			<td style="width:135px;">DZF-6050</td>
			<td style="width:287px;">Used to reduce the cure time of the silicone rubber</td>
		</tr>
		<tr height="63">
			<td height="63" style="height:63px;width:207px;">Male stud push in fit pneumatic fitting</td>
			<td style="width:168px;">Zhe Jiang BLCH Pneumatic Science &#38; Technology</td>
			<td style="width:135px;">PC4-01</td>
			<td style="width:287px;">Used to connect the tubing and the 3D-printed actuator tubing connector</td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:207px;">Tubing</td>
			<td style="width:168px;">SMC</td>
			<td style="width:135px;">TU0425</td>
			<td style="width:287px;">Used for actuating the actuators</td>
		</tr>
		<tr height="63">
			<td height="63" style="height:63px;width:207px;">Vacuum pump</td>
			<td style="width:168px;">Zhe Jiang BLCH Pneumatic Science &#38; Technology</td>
			<td style="width:135px;"></td>
			<td style="width:287px;">Used as the air source</td>
		</tr>
		<tr height="63">
			<td height="63" style="height:63px;width:207px;">Pressure valve</td>
			<td style="width:168px;">Zhe Jiang BLCH Pneumatic Science &#38; Technology</td>
			<td style="width:135px;">IR1000-01BG</td>
			<td style="width:287px;">Used for adjusting the input air pressure</td>
		</tr>
	</tbody>
</table>

fabrication of soft pneumatic network actuators with oblique chambers

软气动网络驱动器已成为软机器人中最有希望的驱动装置之一, 其主要优点是弯曲变形大, 输入低。然而, 它们在二维 (2 维) 空间中单调的弯曲运动形式使它们远离广泛的应用。本文给出了斜腔软气动网络驱动器的详细制作方法, 探讨了其在三维 (3) 空间中的运动。斜腔的设计使驱动器具有可调谐的耦合弯曲和扭转能力, 使他们有可能在灵活的机械手中移动巧妙, 成为生物启发的机器人和医疗设备。制造过程是基于成型方法, 包括硅胶弹性体的准备, 室和基础零件的制造, 执行器装配, 油管连接, 检查泄漏, 和执行器维修。该制造方法保证了在模具中只进行少量修改的一系列驱动器的快速制造。试验结果表明, 该传动机构质量优良, 弯曲、扭转能力显著。该夹具的实验表明, 在适应不同直径的物体和提供足够的摩擦力方面发展的优势。

单驱动器: 为了验证制造方法, 证明了执行器的功能, 并对其进行了测试。对于实验装置, 采用空气泵来激活阀门。阀门连接到执行器以控制内部压力。单执行器固定在其连接端, 垂直放置。当执行器被加压时, 两个数码相机被用来从不同的角度捕捉它的位置。分析位置 (图 3A), 明确了执行机构的运动可以用两个参数来描述: ?...

Watch this Scientific Journal Video about Fabrication of Soft Pneumatic Network Actuators with Oblique Chambers at JoVE.com

Fabrication of Soft Pneumatic Network Actuators with Oblique Chambers

本文介绍了一种带斜腔的软气动网络驱动器的制作方法。该驱动器能够产生耦合弯曲和扭转运动, 从而拓宽了它们在软机器人中的应用。

斜腔软气动网络驱动器的研制

Soft pneumatic network actuators have become one of the most promising actuation devices in soft robotics which benefits from their large bending ...

This method answers the key questions in the field of soft cell robotics by showing the fabrication method of soft pneumatic network actuators with oblique chambers that characterizes coupled bending and twisting motions. The main advantage of this technique is that it is fast, reliable, low-cost and suitable for the fabrication of soft pneumatic actuators with varied structures. Generally, individuals new to this method will struggle because the fabrication contains many steps, and one minor inappropriate operation can cause lethal failure of the actuators.The fabrication process requires molds. Design and 3D print a set of molds for the actuator with a 30 degree oblique chamber. Two parts will form the chamber mold, with one part having a hole to create a tubing connection.The third part will form a base. Next, place a mixing container on a scale. In separate syringes, have silicone elastomer component parts A and B.Use the syringes and scale to add the desired mass of each component to the mixing container.Now, move the mixing container to a Planetary Centrifugal mixer and mix well. After mixing, the silicone elastomer is ready for the protocol. Work with the mold pieces for the chamber.On each of the pieces, evenly spray mold release agent for silicone elastomer products. Orient the two pieces properly and bring them together to assemble the mold. Hold both ends of the mold with clips to prevent leakage.Get five milliliters of silicone elastomer with a syringe. Inject the elastomer slowly into the hole of the mold to fabricate the connection end. Then, fill the whole mold with the silicone elastomer.Use a low-flow rate and move the elastomer back and forth slowly. Once the mold is filled, use a needle to pierce any bubbles that form on the surface. Use a blade to scrape off excess elastomer on the upper surface of the mold.Now, place the mold in a 70 degrees Celsius oven until it is cured. After curing, inspect the mold. Use a syringe to inject silicone elastomer into bubbles and holes on the surface of the actuator.Scrape off any excess elastomer on the surface. Return the mold to the 70 degrees Celsius oven until it is cured. This is an example of a chamber produced by these steps after curing and demolding.Get the mold piece for the base. Spray mold release agent for the silicone elastomer evenly on its surface. Pour the silicone elastomer into the mold to fill it completely.Then, with a needle, pierce any bubbles that form on the surface. Scrape off any excess silicone elastomer along the upper surface with a blade. Place the mold in a 70 degree Celsius oven until the silicone elastomer is cured.This is an example of the base produced by these steps after curing and demolding. At this point, the actuator components are ready. Work with both a chamber and a base.Begin by pouring a one millimeter thick layer of silicone elastomer on one face of the base. Then, place the chamber part on the base. There will be a space between the two pieces.Use a syringe to inject silicone elastomer into the space. Place the actuator in the oven at 70 degrees Celsius until the elastomer is cured. After curing the actuator, tap the actuator tubing connector.It should accept the screw of a male stud push-in fit pneumatic fitting. With a needle, pierce the connection end of the actuator along the central line of the cylinder. Use a steel rod to increase the diameter of the hole to about two millimeters.Get the actuator tubing connector and screw it into the actuator. Once it is in place, push a section of tubing into the pneumatic fitting. The final step is to check for leaks.For this, use a container of water that can cover the actuator. Get the actuator and connect it to an air source. Place the entire actuator into the water and pressurize it.Observe whether bubbles are formed due to a leak. After the test, remove the actuator from the water. In this video, a 30 degree actuator starts under zero applied air pressure.As the pressure increases from zero kilopascals to 90 kilopascals, without interruption, the actuator both bends and twists. As the pressure is reduced, it returns to its original state. The bending angle for the actuator is defined as the angle between the body line in unactuated position and the body line in the actuated position.The twisting angle is the angle between the tip line in the unactuated position and the actuated position. This plot shows the bending angle as a function of pressure for actuators with oblique angles of 30, 45 and 60 degrees. Here is a similar plot for the twisting angle as a function of pressure.Note the difference in the vertical scales. While attempting this procedure, it is important to remember to pierce any bubbles that form on the top surface and scrape off excess elastomer on the upper surface of the mold before placing it into the oven. In this procedure, the silicone elastomer can be mixed manually and the elastomer can be cured at room temperature if the mixer and oven are not available.After its development, this method has paved the way for researchers in the fabrication of soft pneumatic actuators to explore oblique chambers capable of bending and twisting motion in 3D space. Don't forget that working with needles and blades can be extremely hazardous and attention should be paid;avoiding any hurt. In addition, nitrile gloves should always be worn when working with silicone elastomers.

Research

JoVE Journal

Engineering

Fabrication of Low Temperature Carbon Nanotube Vertical Interconnects Compatible with Semiconductor Technology

低温碳纳米管垂直互连的制作兼容半导体技术

We demonstrate a method for the low temperature growth (350 &#176;C) of vertically-aligned carbon nanotubes (CNT) bundles on electrically conductive ...

科研

工程学

Fabrication Process of Silicone-based Dielectric Elastomer Actuators

有机硅为基础的介电弹性体致动器的制作工艺

This contribution demonstrates the fabrication process of dielectric elastomer transducers (DETs). DETs are stretchable capacitors consisting of an ...

Indirect Fabrication of Lattice Metals with Thin Sections Using Centrifugal Casting

与超薄切片格金属制造间接使用离心铸造

One of the typical methods to manufacture 3D lattice metals is the direct-metal additive manufacturing (AM) process such as Selective Laser Melting (SLM) ...

A Fabrication Method for Highly Stretchable Conductors with Silver Nanowires

对于高伸缩的导线与银纳米线制作方法

Stretchable electronics are identified as a key technology for electronic applications in the next generation. One of the challenges in fabrication of ...

Free-form Light Actuators &#8212; Fabrication and Control of Actuation in Microscopic Scale

自由形式的光驱动器 - 制作和开动控制在微观尺度

Liquid crystalline elastomers (LCEs) are smart materials capable of reversible shape-change in response to external stimuli, and have attracted ...

Fabrication of White Light-emitting Electrochemical Cells with Stable Emission from Exciplexes

白的制造发光电化学细胞与来自激发络合物稳定的发射

The authors present an approach for fabricating stable white light emission from polymer light-emitting electrochemical cells (PLECs) having an active ...

Experimental Implementation of a New Composite Fabrication Method: Exposing Bare Fibers on the Composite Surface by the Soft Layer Method

一种新的复合制备方法的实验实现: 用软层法对复合材料表面裸露纤维进行曝光

The bipolar plate is a key component in proton exchange membrane fuel cells (PEMFCs) and vanadium redox flow batteries (VRFBs). It is a multi-functional ...

Fabrication of Ultra-thin Color Films with Highly Absorbing Media Using Oblique Angle Deposition

用斜角沉积法制备高吸收介质的超薄彩色薄膜

Ultra-thin film structures have been studied extensively for use as optical coatings, but performance and fabrication challenges remain.&#160; We present ...

A Soft Tooling Process Chain for Injection Molding of a 3D Component with Micro Pillars

微柱3D 构件注塑成型的软加工工艺链

The purpose of this paper is to present the method of a soft tooling process chain employing Additive Manufacturing (AM) for fabrication of injection ...

Fabrication of Microscope Stage for Vertical Observation with Temperature Control Function

具有温度控制功能的垂直观测显微镜级的制造

Samples are usually placed onto a horizontal microscope stage for microscopic observation. However, to observe the influence of gravity on a sample or ...