우리는 이 간단한 방법을 사용하여 도금 용액의 일체형 구리 농도를 정량화하는 데 성공했습니다. 정량화함으로써, 단원 구리는 누구나 사용할 수있는 매개 변수입니다. 우리의 연구는 미래의 도금 기술에 기여할 것입니다.
중화 및 BCS 솔루션이 사전에 준비되는 경우. 도금 용액을 혼합하여 측정하기만 하면 단일 원가 구리의 제조 현장 측정에서도 가능합니다. 도금 욕탕에서 단원구리의 변이를 모니터링합니다.
그 결과 제조 공정이 개선되었습니다. 우리의 목표는 용액의 광학 평가를 기반으로 코팅 품질의 예측입니다. 광학 방법은 생산 현장에 매우 적합합니다.
IoT에 제조 기술을 만들기 위한 핵심 장치가 될 것입니다. 이 절차를 시작하려면 200 밀리리터 비커에 스티어 바를 추가합니다. 구리 황산도용 150밀리리터를 비커에 붓습니다.
그리고 도금 용액을 실온에서 1 시간 동안 둡니다. 분당 85 밀리리터의 유량으로 질소 가스의 흐름을 시작합니다. 질소 가스가 비커에 들어가기 전에 튜브를 삽입합니다.
그리고 적어도 30 분 동안 도금 용액을 탈산화. 금속 가위를 사용하여 3밀리미터 두께의 구리 플레이트를 9.5cm에서 2센티미터로 추가합니다. 동일한 치수에 1mm 두께의 백금 판을 추가합니다.
에탄올로 구리와 백금 판을 모두 씻으십시오. 그리고 순수한 물로 헹구는 다. 질소 가스를 사용하여 플레이트를 건조시다.
고정 지그에 접시를 부착합니다. 비커 내부에 지그를 삽입하고 제자리에 고정합니다. 구리 플레이트의 전극을 전원 공급 장치의 양수 끝에 연결합니다.
그리고 백금 판의 전극을 음의 끝에 연결합니다. 하나의 암페어의 일정한 전류에서 전원 공급 장치를 켭니다. 10분 후 전원을 끄고 교반기전원을 멈춥니다.
용액을 약 10분 동안 쉬어 파티클이 정착하도록 합니다. 두 개의 흡수 측정 세포를 설정하고 각각에 저어 바를 추가합니다. 그런 다음 2.5 밀리리터의 중화 용액을 붓습니다.
그리고 BCS 용액의 219 마이크로 리터. 샘플 및 참조를 위해 두 개의 셀을 준비합니다. 도금 용액 샘플 22 마이크로리터에 섞고 20분간 저어줍니다.
중화 솔루션은 주황색을 개발할 것입니다. 비 전기 분해 도금 용액을 참조와 혼합합니다. 이 솔루션의 색상은 파란색이 될 것입니다.
UV-Vis 분광광계를 사용하여 400 내지 600 나노미터의 파장 범위에서 시료 용액의 흡수 스펙트럼을 측정합니다. 분사 측정을 위해 20분 이상의 시간 측정 기능을 갖춘 UV-Vis 분광측계를 사용하십시오. 분광계에는 주사기 포트가 있는 샘플 챔버 커버가 있어야 합니다.
그리고 교반기와 온도 조절 기 세포 홀더. 교반기 막대가 포함된 셀에서 중화 용액과 BCS 용액을 준비합니다. 홀더에 셀을 설정하고 교반기 회전 속도를 최대로 설정합니다.
시간 측정 모드에서측정 시간을 485나노미터에서 1270초로 설정하고 레코딩을 시작합니다. 시작 후 1 분 챔버 커버의 주사기 포트에서 도금 용액 샘플의 22 마이크로 리터를 주입하는 파이펫을 사용합니다. 구리 1및 BCS에 대한 반응 곡선을 획득합니다.
도금 솔루션에서 구리 의 농도는 485 나노미터에 배치 된 BCS 키에 구리 하나의 흡수로부터 결정 될 수있다. 대표적인 도금 솔루션의 흡수 스펙트럼은 여기에 나와 있다. 구리 1 농도는 전기 분해 시간에 따라 0분에서 10분으로 증가하는 경향이 있습니다.
전기도금 용액의 색 반응의 변화 및 흡광도를 시뮬레이션하는 곡선이 여기에 나와 있다. 시뮬레이션에서 구리 하나 축적과 관련된 파라미터가 정량화된다. 그런 다음 즉각적으로 반응하는 구성 요소의 시뮬레이션 값, 전해질 된 도금 솔루션의 0이 플롯됩니다.
A0의 값은 전해 4분 후에 크게 변하지 않았지만, 전동 분해 시간에 대응하는 증가는 6분에서 10분 사이에 보입니다. 각 전기 분해 용액은 구리 플레이트에 도금되어 구리 가 거칠기 및 모양과 같은 구리 도금의 품질에 미치는 영향을 조사합니다. SEM 이미지에서 0분 4분 전해 용액을 사용하는 코팅 표면 구조는 거의 구별할 수 없습니다.
전해 의 6 분 후 표면에 약간의 붓기를 도금 볼 수 있습니다. 10 분 후 큰 두툼한 거칠기가 있습니다. 일반적인 색 반응과 비교하여 복잡하고 단발적인 구리 및 BCS를 형성하거나 최소 20 분 동안 정확한 측정을 하는 데 시간이 걸립니다.
사출 방법은 보다 정확한 측정을 위해 사용됩니다. 색상 반응의 시간 반응과 함께. 또한 단일 형 구리의 보존 성분을 분석 할 수 있습니다.
전통적으로 일제적 구리는 액체 용액에 안정적으로 존재하지 않는다고 생각되었습니다. 우리는 도금 용액의 단가성 구리를 눈에 띄게 했습니다.