Vi har lykkes i å kvantifisere monovalent kobberkonsentrasjon i plating løsning ved hjelp av denne enkle metoden. Ved kvantifisering er monovalent kobber en parameter som alle kan bruke. Vår forskning vil bidra til fremtidig plating teknologi.
Hvis nøytraliserende og BCS-løsninger er utarbeidet på forhånd. Bare bland plating løsningen og måle den, så selv på produksjonsstedet måling av monovalent kobber blir mulig. Vi overvåker variasjonen av monovalent kobber i plating badet.
Som resulterte i forbedring av produksjonsprosessen. Vårt mål er prediksjon av beleggkvalitet basert på optisk evaluering av løsningen. Optiske metoder er ekstremt egnet for produksjonssteder.
Det vil være en viktig enhet for å lage produksjonsteknologi til IoT. For å begynne denne prosedyren legg til en rørestang til et 200 milliliter beger. Hell 150 milliliter kobbersulfatplatingoppløsning i begeret.
Og la platingløsningen stå ved romtemperatur i en time. Begynn strømmen av nitrogengass med en strømningshastighet på 85 milliliter per minutt. Sett røret før nitrogengassen inn i begeret.
Og deoxidize plating løsningen i minst 30 minutter. Ved hjelp av metallsaks tilsett en 3 millimeter tykk kobberplate til 9,5 centimeter med to centimeter. Tilsett en 1 millimeter tykk platinaplate i samme dimensjoner.
Vask både kobber- og platinaplatene med etanol. Og skyll deretter med rent vann. Bruk nitrogengass til å tørke platene.
Fest platene til festejiggen. Sett inn jiggen inne i begeret og fest den på plass. Koble elektroden på kobberplaten til den positive enden av strømforsyningen.
Og koble elektroden av platinaplaten til den negative enden. Slå på strømforsyningen med en konstant strøm på ett ampere. Etter 10 minutter slår du av strømmen og stopper omrøreren.
La oppløsningen hvile i ca. 10 minutter for å la partiklene bosette seg. Sett ut to absorpsjonsmålingsceller og legg til en rørestang til hver. Hell deretter i 2,5 milliliter nøytraliseringsløsning.
Og 219 mikroliter bcs løsning. Klargjør to celler for prøve og referanse. Bland i 22 mikroliter med plating løsningsprøve og rør i 20 minutter.
Nøytraliserende løsning vil utvikle en oransje farge. Bland ikke-elektrolyseplatingoppløsningen med referansen. Fargen på denne løsningen vil være blå.
Bruk et UV-Vis spektrofotometer for å måle absorpsjonsspektraet til prøveløsningen i bølgelengdeområdet på 400 til 600 nanometer. Bruk et UV-Vis spektrofotometer med en tidsmålingsfunksjon på mer enn 20 minutter til injeksjonsmåling. Spektrofotometeret bør ha et prøvekammerdeksel med en sprøyteport.
Og en termostatcelleholder med røre. Forbered en nøytraliserende løsning og en BCS-løsning i en celle som inneholder en rørebar. Sett cellen i holderen og vri omrørerrotasjonshastigheten til maksimum.
I tidsmålingsmodus angir du måletiden til 1270 sekunder ved 485 nanometer og starter opptaket. Ett minutt etter at du har startet, bruk en pipette til å injisere 22 mikroliter av platingoppløsningsprøven fra sprøyteporten på kammerdekselet. Oppnå reaksjonskurver for kobber en og BCS.
Konsentrasjonen av kobber en i plating løsninger kan bestemmes fra absorbans av kobber en til BCS nøkkel lagt på 485 nanometer. Absorpsjonsspektraet av representative plating løsninger er vist her. Kobber en konsentrasjon har en tendens til å øke fra null minutter til 10 minutter avhengig av elektrolyse tid.
En kurve som simulerer endringen og absorbansen av fargereaksjonen til galvaniseringsløsningen er vist her. Fra simuleringen er parametrene knyttet til kobber en akkumulering kvantifisert. Deretter er simuleringsverdien av komponenten som reagerer øyeblikkelig, En null i platingløsningen som ble elektrolysert, plottes.
Mens verdien av A0 ikke endret seg betydelig før etter fire minutter med elektrolyse, ses en økning tilsvarende elektrolysetid mellom seks og 10 minutter. Hver elektrolyseløsning er belagt på kobberplater for å undersøke påvirkning av kobber en på kvaliteten på kobberplating som ruhet og form. Fra SEM-bildene er beleggoverflatestrukturene fra å bruke nullminuttene og fire minutter elektrolyseløsningene nesten umulig å skille.
Etter seks minutter med elektrolyse plating noen hevelse på overflaten kan sees. Mens etter 10 minutter er det en stor tykk grovhet. Sammenlignet med generell fargereaksjon tar det tid å danne et komplekst eller monovalent kobber og BCS eller nøyaktig måling fortsatt i minst 20 minutter.
Injeksjonsmetoden brukes til mer nøyaktig bestemmelse. Sammen med tidsresponsen til fargereaksjonen. Det er også mulig å analysere oppbevaring komponenten av monovalent kobber.
Tradisjonelt har det blitt antatt at monovalent kobber ikke eksisterer stabilt i flytende løsning. Vi gjorde det monovalente kobberet i platingløsningen synlig.