conducting-elevated-temperature-normal-combined-pressure-shear-plate

Conducting Elevated Temperature Normal and Combined Pressure-Shear Plate Impact Experiments Via a Breech-end Sabot Heater System

A novel approach for conducting normal and/or combined pressure-shear plate impact experiments at test temperatures up to 1000 &#176;C is presented. The ...

Case Western Reserve University

In the United States there is currently a paucity of available real world minor rear crash data with struck vehicle delta-V, or speed change, less than or equal to 15 kilometers per hour. These data are essential as researchers attempt to define 'whiplash' injury risk potential in these minor crashes. This study analyzed a new set of 105 U.S. minor rear aligned crashes between passenger vehicles. Mean struck vehicle delta-V and acceleration were 6.3 km/h (s.d. = 2.1 km/h) and 1.4 g (s.d. = 0.5 g), respectively. A total of 113 struck vehicle occupants were diagnosed within five weeks post-crash with 761 ICD-9-CM complaints and 427 AIS injuries (99.5% AIS1) attributed to the crashes. No striking vehicle occupants reported complaints. The main ICD-9-CM diagnoses were 40.6% cervical, 22.5% lumbar/sacral and 10.2% thoracic and the main AIS1 diagnoses were 29.7% cervical, 23.2% lumbar/sacral and 14.3% thoracic. The diagnosis disparity was mainly due to coding for pre-existing degenerative diagnosis in ICD-9-CM. Degenerative spine conditions were not significant for increased AIS1 injury risk. Surprisingly, many non-'whiplash' diagnoses were found. The AIS injury diagnosis distribution and frequency in these minor delta-V crashes did not correspond with previous minor rear crash studies. A prospectively collected and unbiased minor rear crash databank in the model of CIREN or NASS is highly desirable to verify or refute these results for the U.S. population since the current study cohort may have been influenced by litigation.

Minor crashes and 'whiplash' in the United States.

This paper reports dependency of specific heat and ballistic thermal conductance on cross-sectional geometry (tube versus rod) and size (i.e., diameter and wall thickness), in free-standing isotropic non-metallic crystalline nanostructures. The analysis is performed using dispersion relations found by numerically solving the Pochhammer-Chree frequency equation for a tube. Estimates for the allowable phonon dispersion relations within the crystal lattice are obtained by modifying the elastic acoustic dispersion relations so as to account for the discrete nature of the material's crystal lattice. These phonon dispersion relations are then used to evaluate the specific heat and ballistic thermal conductance in the nanostructures as a function of the nanostructure geometry and size. Two major results are revealed in the analysis: increasing the outer diameter of a nanotube while keeping the ratio of the inner to outer tube radius (gamma) fixed increases the total number of available phonon modes capable of thermal population. Secondly, decreasing the wall thickness of a nanotube (i.e., increasing gamma) while keeping its outer diameter fixed, results in a drastic decrease in the available phonon mode density and a reduction in the frequency of the longitudinal and flexural acoustic phonon modes in the nanostructure. The dependency of the nanostructure's specific heat on temperature indicates 1D, 2D, and 3D geometric phonon confinement regimes. Transition temperatures for each phonon confinement regime are shown to depend on both the nanostructure's wall thickness and outer radius. Compared to nanowires (gamma = 0), the frequency reduction of acoustic phonon modes in thinner walled nanotubes (gamma = 0.96) is shown to elevate the ballistic thermal conductance of the thin-walled nanotube between 0.2 and 150 K. At 20 K, the ballistic thermal conductance of the thin-walled nanotube (gamma = 0.96) becomes 300% greater than that of a solid nanowire. For temperatures above 150 K, the trend in ballistic thermal conductance inverts. The greater number of phonon modes in nanostructures with increased outer diameter and wall thickness is shown to have a larger contribution to ballistic thermal conductance when compared to the increased contribution from the frequency reduction of acoustic phonon modes in thinner walled nanotubes.

Application of elastic wave dispersion relations to estimate thermal properties of nanoscale wires and tubes of varying wall thickness and diameter.

While Photonic Doppler Velocimetry (PDV) has become a common diagnostic tool for the measurement of normal component of particle motion in shock wave experiments, this technique has not yet been modified for the measurement of combined normal and transverse motion, as needed in oblique plate impact experiments. In this paper, we discuss the design and implementation of a compact fiber-optics-based heterodyne combined normal and transverse displacement interferometer. Like the standard PDV, this diagnostic tool is assembled using commercially available telecommunications hardware and uses a 1550 nm wavelength 2 W fiber-coupled laser, an optical focuser, and single mode fibers to transport light to and from the target. Two additional optical probes capture first-order beams diffracted from a reflective grating at the target free-surface and deliver the beams past circulators and a coupler where the signal is combined to form a beat frequency. The combined signal is then digitized and analyzed to determine the transverse component of the particle motion. The maximum normal velocity that can be measured by this system is limited by the equivalent transmission bandwidth (3.795 GHz) of the combined detector, amplifier, and digitizer and is estimated to be ∼2.9 km/s. Sample symmetric oblique plate-impact experiments are performed to demonstrate the capability of this diagnostic tool in the measurement of the combined normal and transverse displacement particle motion.

Vikas Prakash

Department of Mechanical and Aerospace Engineering

Case Western Reserve University

Conducting Elevated Temperature Normal and Combined Pressure-Shear Plate Impact Experiments Via a Breech-end Sabot Heater System

Vikas Prakash

.css-o250i3{font-size:18px;font-family:Open Sans,sans-serif;line-height:21.6px;}Department of Mechanical and Aerospace Engineering

Case Western Reserve University

Conducting Elevated Temperature Normal and Combined Pressure-Shear Plate Impact Experiments Via a Breech-end Sabot Heater System

Department of Mechanical and Aerospace Engineering