准备E18胎鼠皮层神经元为条块开始之前，重要的是温暖的一切必要的媒体和试剂，以37 ° C 同样重要的是消毒一切准备的细胞（例如，橡胶灯泡，试管架，媒体瓶，等），并用70％乙醇擦拭，这是摆在引擎盖。 <ol><li>放置在一个15毫升中含1毫升冰冷无钙镁免费清扫缓冲管两件E18胎鼠皮层（大脑，以前解剖）。 </li><li>加入1毫升0.25％胰蛋白酶- EDTA的皮质夹层缓冲，使最终体积为2毫升和最终胰蛋白酶的浓度为0.125％。 </li><li>在37℃水浴8分钟中放置15毫升管。 </li><li>在此期间，消防波兰3玻璃巴斯德吸管，形成连续较小的开口，在生物安全柜，以帮助保持无菌。 </li><li>皮层潜伏期8分钟后，添加10毫升的DMEM含10％胎牛血清的皮质，以帮助阻止胰蛋白酶反应。 </li><li>离心15 mL的试管中，在2分钟2500转的皮质和DMEM/10％FBS。 </li><li>在生物安全柜，取出上清液用巴斯德玻璃吸管连接真空吸皮质。要小心不要去打扰或撞出颗粒。 </li><li>加入1毫升的NMB皮层颗粒，轻轻吸管向上和向下。这是非常重要，以避免产生气泡而pipeting向上和向下，气泡可损害细胞氧化。 </li><li>使用最广泛的开放的火抛光的巴斯德吸管磨碎附加无菌的橡胶球，最终pipeting向上和向下的5倍皮层，再小心不要引入气泡。这个过程中继续与其他2个玻璃吸管，每一个开口尺寸减少。 </li><li> trituration后，再次离心下来的细胞在2分钟2500转。 </li><li>离心后，再次去除上清，重悬细胞沉淀在2毫升的NBM。 </li><li>通过一个45微米的细胞过滤器过滤悬浮细胞溶液。 </li><li>用台盼蓝染色，计数，并加载到设备的细胞。我们通常装载20细胞每台设备的UL。 </li></ol> 注 ：终浓度的细胞通常是250万细胞/毫升和800万细胞/毫升之间载入细胞后的细胞已被计算，它是时间的负载设备的细胞： <ol><li>把先前准备好的设备，将含有生物安全柜的NBM保持无菌。 </li><li>从井中取出多余的介质，通过真空抽吸。但是，要小心，以避免删除所有的媒体 - 必须有一些媒体的主渠道。 </li><li> 20细胞UL应用设备的顶部左手水库（如有必要，见图表）。细胞进入设备的流量和连接到PLL的表面处理。 </li><li>加载后，放置10分钟含细胞回的设备，让细胞附着在一个孵化器。 </li><li> 10分钟后，填补与媒体和地方的设备在孵化器的水库。 </li></ol>

<ol>
	<li>Park, J. W., Vahidi, B., Taylor, A. M., Rhee, S. W., Jeon, N. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Microfluidic+culture+platform+for+neuroscience+research.">Microfluidic culture platform for neuroscience research.</a> Nat Protoc. 1, 2128-2136 (2006).</li><li>Taylor, A. M., Blurton-Jones, M., Rhee, S. W., Cribbs, D. H., Cotman, C. W., Jeon, N. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+microfluidic+culture+platform+for+CNS+axonal+injury,+regeneration+and+transport.">A microfluidic culture platform for CNS axonal injury, regeneration and transport.</a> Nat Methods. 2, 599-605 (2005).</li></ol>

根据不同的应用，可以是多种多样的细胞密度。然而，播种密度过低的主要神经元通常会导致细胞死亡。根据不同的孵化器和湿度水平，媒体可能需要在设备改为每2至3天。不断变化的媒体时，这是很重要的媒体取出后水库，切勿从媒体的主渠道。此外，新媒体，并放置在顶部的井，让一些新鲜的媒体流通过设备进入主渠道，填补了所有的水塘前，它是很好的做法。

<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
<html xmlns="http://www.w3.org/1999/xhtml" xml:lang="en" lang="en">	
		
		<div>
		<table border="1">
		<thead>
		<tr>
		<th>Material Name</th>
		<th>Type</th>
		<th>Company</th>
		<th>Catalogue Number</th>
		<th>Comment</th>
		</tr>
		</thead>
		<tbody>
		
<tr>
<td>NBM</td>
<td>medium</td>
<td>Invitrogen</td>
<td>21103-049</td>
<td>Neural Basal Media is obtained by Invitrogen under their Gibco line of cell culture reagents.</td>
</tr>
<tr>
<td>E18 rat embryos</td>
<td>Animal</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>Obtained from pregnant Sprague Dawley Rats. The pregnant rat is sacrificed and the E18 fetal rat pups dissected to obtain the E18 fetal rat cortex.</td>
</tr>
<tr>
<td>CMFM dissection buffer HBSS</td>
<td>buffer</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>ice-cold Calcium-free Magnesium-free dissection buffer HBSS based.</td>
</tr>
<tr>
<td>15 ml Tube</td>
<td>Tool</td>
<td>BD Falcon</td>
<td>Falcon No. 352097</td>
<td>Available through Fisher Scientific catalog number 14-959-70C</td>
</tr>
<tr>
<td>0.25% Trypsin-EDTA</td>
<td>Reagent</td>
<td>Invitrogen</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<tr>
<td>37&#x02DA;C water bath</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<tr>
<td>Pasteur pipets</td>
<td>&nbsp;</td>
<td>Fisher Scientific</td>
<td>&nbsp;</td>
<td>glass</td>
</tr>
<tr>
<td>DMEM</td>
<td>medium</td>
<td>Invitrogen</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<tr>
<td>FBS</td>
<td>Reagent</td>
<td>Invitrogen</td>
<td>&nbsp;</td>
<td>serum, used at 10% in DMEM</td>
</tr>
<tr>
<td>centrifuge</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>set at 2500 rpm </td>
</tr>
<tr>
<td>Trypan Blue</td>
<td>&nbsp;</td>
<td>Invitrogen</td>
<td>&nbsp;</td>
<td>for counting live/dead cells</td>
</tr>
<tr>
<td>BD Falcon Cell Strainer 40 um</td>
<td>Tool</td>
<td>BD Falcon</td>
<td>Falcon cat# 352340</td>
<td>Available through Fisher Scientific. Fisher catalog# 08-771-1</td>
</tr>
<tr>
<td>B27</td>
<td>Reagent</td>
<td>Invitrogen</td>
<td>17504-044</td>
<td>B27 is a proprietary supplement available through Invitrogen under their Gibco line of cell culture reagents.</td>
</tr>
<tr>
<td>Glutamax</td>
<td>Reagent</td>
<td>Invitrogen</td>
<td>35050-061</td>
<td>Glutamax is available through Invitrogen under their Gibco line of celll culture reagents.</td>
</tr>		</tbody>
		</table>
		</div>

preparing e18 cortical rat neurons for compartmentalization in a microfluidic device

在这个视频中，我们展示了E18皮质大鼠神经元的准备。 E18皮质大鼠以前解剖，并准备从E18胎鼠大脑皮层神经元得到。 E18皮层，清扫后，立即到单个神经元的分离。它可以存储长达一个星期的E18皮质休眠发送含有B27的缓冲区4 ° C的分解是执行之前。然而，将细胞活力下降。通常情况下，我们获得我们的E18的Cortex新鲜。在冰冷的无钙镁免费清扫缓冲区（招商基金）被运送到实验室。抵达后，胰蛋白酶添加到皮质的终浓度为0.125％。皮层，然后在37℃孵育8分钟。 DMEM培养液含10％胎牛血清添加到皮质停止反应。然后在2分钟2500转离心皮质。上清被删除，含2％B27（体积/体积）和0.25％Glutamax（体积/体积），然后向上和向下吹打重悬的皮质神经基底媒体2毫升（NBM）。下一步，皮质是磨碎与以前火抛光的玻璃滴管，用较小的一个连续的开放每个。研制过程后，皮层再次离心2分钟2500转。然后取出上清液和皮质颗粒重新悬浮2毫升含有B27与Glutamax的NBM。细胞悬液，然后通过一个40微米的尼龙细胞过滤网。下一步的细胞计数。现正准备装载到神经元的微流体装置的神经元。

Watch this Scientific Journal Video about Preparing E18 Cortical Rat Neurons for Compartmentalization in a Microfluidic Device at JoVE.com

Preparing E18 Cortical Rat Neurons for Compartmentalization in a Microfluidic Device

在这个视频中，我们展示了E18皮质大鼠神经元的准备。

准备在微流体装置E18条块皮质大鼠神经元

In this video, we demonstrate the preparation of E18 cortical rat neurons. E18 cortical rat neurons are obtained from E18 fetal rat cortex previously ...

preparing-e18-cortical-rat-neurons-for-compartmentalization

Research

JoVE Journal

Biology

19.6K 次观看.  University of California, Irvine (UCI). 在这个视频中，我们展示了E18皮质大鼠神经元的准备。

视频: Preparing E18 Cortical Rat Neurons for Compartmentalization in a Microfluidic Device

Organotypic Slice Culture of E18 Rat Brains

Organotypic slice cultures from embryonic rodent brains are widely used to study brain development. While there are often advantages to an in-vivo system, organotypic slice cultures allow one to perform a number of manipulations that are not presently feasible in-vivo. To date, organtotypic embryonic brain slice cultures have been used to follow individual cells using time-lapse microscopy, manipulate the expression of genes in the ganglionic emanances (a region that is hard to target by in-utero electroporation), as well as for pharmacological studies. In this video protocol we demonstrate how to make organotypic slice cultures from rat embryonic day 18 embryos. The protocol involves dissecting the embryos, embedding them on ice in low melt agarose, slicing the embedded brains on the vibratome, and finally plating the slices onto filters in culture dishes. This protocol is also applicable in its present form to making organotypic slice cultures from different embryonic ages for both rats and mice. 

器官型E18大鼠脑切片文化

Organotypic slice cultures from embryonic rodent brains are widely used to study brain development. While there are often advantages to an in-vivo system, ...

科研

生物学

Fabrication of a Microfluidic Device for the Compartmentalization of Neuron Soma and Axons

In this video, we demonstrate the technique of soft lithography with polydimethyl siloxane (PDMS) which we use to fabricate a microfluidic device for culturing neurons. Previously, a silicon wafer was patterned with the design for the neuron microfluidic device using SU-8 and photolithography to create a master mold, or what we simply refer to as a "master". Next, we pour the silicon polymer PDMS on top of the master which is then cured by heating the PDMS to 80&deg;C for 1 hour. The PDMS forms a negative mold of the device. The PDMS is then carefully cut and lifted away from the master. Holes are punched where the reservoirs will be and the excess PDMS trimmed away from the device. Nitrogen is used to blow away any excess debris from the device. At this point the devices are now ready for use and can either bonded to corning No. 1 cover glass with a plasma sterilizer/cleaner or can be reversibly bound to the cover glass by simply placing the device on top of the cover glass. The reversible bonding of the device to glass is covered in a separate video and requires first that the device be sterilized either with 70% ethanol or by autoclaving. Plasma treating sterilizes the devices so no further treatment is necessary. It is, however, important, when plasma-treating the devices, to add liquid to the devices within 10 minutes of the plasma treatment while the surfaces are still hydrophilic. Waiting longer than 10 minutes to add liquid to the device makes it difficult for the liquid to enter the device. The neuron devices are typically plasma-bound to cover glass and 0.5 mg/ml poly-L-lysine (PLL) in pH 8.5 borate buffer is immediately added to the device. After a minimum of 3 hours incubating with PLL, the devices are washed with dH2O water a minimum of 3 times with at least 15 minutes between each wash. Next, the water is removed and fresh media is added to the device. At this point the device is ready for use. It is important to remember at this point to never remove all the media from the device. Always leave media in the main channel.

In this video we demonstrate the technique of soft lithography with polydimethyl siloxane (PDMS) which we use to farbricate a microfluidic device for culturing neurons.

条块索玛的神经元和轴突的一个微流体设备制造

In this video, we demonstrate the technique of soft lithography with polydimethyl siloxane (PDMS) which we use to fabricate a microfluidic device for ...

A Microfluidic Device with Groove Patterns for Studying Cellular Behavior

We describe a microfluidic device with microgrooved patterns for studying cellular behavior. This microfluidic platform consists of a top fluidic channel and a bottom microgrooved substrate. To fabricate the microgrooved channels, a top poly(dimethylsiloxane) (PDMS) mold containing the impression of the microfluidic channels was aligned and bonded to a microgrooved substrate. Using this device, mouse fibroblast cells were immobilized and patterned within microgrooved substrates (25, 50, 75, and 100 &mu;m wide). To study apoptosis in a microfluidic device, media containing hydrogen peroxide, Annexin V, and propidium iodide was perfused into the fluidic channel for 2 hours. We found that cells exposed to the oxidative stress became apoptotic. These apoptotic cells were confirmed by Annexin V that bound to phosphatidylserine at the outer leaflet of the plasma membrane during the apoptosis process. Using this microfluidic device with microgrooved patterns, the apoptosis process was observed in real-time and analyzed by using an inverted microscope containing an incubation chamber (37&deg;C, 5% CO2). Therefore, this microfluidic device incorporated with microgrooved substrates could be useful for studying the cellular behavior and performing high-throughput drug screening.

We describe a protocol for the fabrication of microfluidic devices that can enable cell capture and culture. In this approach patterned microstructures such as grooves within microfluidic channels are used to create low shear stress regions within which cell can dock.

微流体装置与Groove的模式，为研究细胞行为

We describe a microfluidic device with microgrooved patterns for studying cellular behavior.  This microfluidic platform consists of a top fluidic channel ...

A Gradient-generating Microfluidic Device for Cell Biology

 The fabrication and operation of a gradient-generating microfluidic device for studying cellular behavior is described.  A microfluidic platform is an enabling experimental tool, because it can precisely manipulate fluid flows, enable high-throughput experiments, and generate stable soluble concentration gradients.  Compared to conventional gradient generators, poly(dimethylsiloxane) (PDMS)-based  microfluidic devices can generate stable concentration gradients of growth factors with well-defined profiles.  Here, we developed simple gradient-generating microfluidic devices with three separate inlets.  Three microchannels combined into one microchannel to generate concentration gradients.  The stability and shape of growth factor gradients were confirmed by fluorescein isothyiocyanate (FITC)-dextran with a molecular weight similar to epidermal growth factor (EGF).  Using this microfluidic device, we demonstrated that fibroblasts exposed to concentration gradients of EGF migrated toward higher concentrations.  The directional orientation of cell migration and motility of migrating cells were quantitatively assessed by cell tracking analysis.  Thus, this gradient-generating microfluidic device might be useful for studying and analyzing the behavior of migrating cells.

We describe a protocol for the microfabrication of the gradient-generating microfluidic device that can generate spatial and temporal gradients in well-defined microenvironment. In this approach, the gradient-generating microfluidic device can be used to study directed cell migration, embryogenesis, wound healing, and cancer metastasis.

一个渐变产生的微流体装置，细胞生物学

 The fabrication and operation of a gradient-generating microfluidic device for studying cellular behavior is described.  A microfluidic platform is an ...

CD4+ T-Lymphocyte Capture Using a Disposable Microfluidic Chip for HIV

CD4 + T淋巴细胞艾滋病毒的捕获使用一次性微流体芯片

Cell Capture Using a Microfluidic Device

细胞捕获使用一个微流体装置

Preparing T Cell Growth Factor from Rat Splenocytes

Maintenance of antigen-specific T cell lines or clones in culture requires rounds of antigen-induced activation separated by phases of cell expansion 1,2. Addition of interleukin 2 to the culture media during the expansion phase is necessary to prevent cell death and sufficient to maintain short-term T cell lines but has been shown to increase Th1 polarization 3. Replacement of interleukin 2 by T cell growth factor (TCGF) which contains a mix of cytokines is more effective than interleukin 2 in maintaining long-term T cell lines in vitro 3. Moreover, TCGF can easily be prepared in large amounts in the laboratory and is much cheaper than recombinant interleukin 2. 
Here, we show how to prepare TCGF from rat splenocyte culture supernatants. For this procedure, we harvest spleens from naive Lewis rats euthanized for thymus and blood collection. We prepare single-cell suspensions from the spleens, lyze the red blood cells by osmotic shock, and seed the splenocytes in culture medium. The cells are stimulated with concanavalin A, a mitogen that non-selectively activates all rat T lymphocytes, inducing the production of cytokines. The culture supernantant is collected 48 hours later andexcess concanavalin A is bound to alpha methyl mannoside to prevent it from activating T cell lines to which TCGF will be added. The TCGF is then sterile-filtered, aliquoted, and stored at -20&deg;C.

We describe the preparation of T cell growth factor used for the in vitro expansion of antigen-specific rat T lymphocyte lines.

准备从大鼠脾细胞T细胞生长因子

Maintenance of antigen-specific T cell lines or clones in culture requires rounds of antigen-induced activation separated by phases of cell expansion 1,2. ...

Assessing Neural Stem Cell Motility Using an Agarose Gel-based Microfluidic Device

While microfluidic technology is reaching a new level of maturity for macromolecular assays, cell-based assays are still at an infant stage1. This is largely due to the difficulty with which one can create a cell-compatible and steady microenvironment using conventional microfabrication techniques and materials. We address this problem via the introduction of a novel microfabrication material, agarose gel, as the base material for the microfluidic device. Agarose gel is highly malleable, and permeable to gas and nutrients necessary for cell survival, and thus an ideal material for cell-based assays. We have shown previously that agarose gel based devices have been successful in studying bacterial and neutrophil cell migration2. In this report, three parallel microfluidic channels are patterned in an agarose gel membrane of about 1mm thickness. Constant flows with media/buffer are maintained in the two side channels using a peristaltic pump. Cells are maintained in the center channel for observation. Since the nutrients and chemicals in the side channels are constantly diffusing from the side to center channel, the chemical environment of the center channel is easily controlled via the flow along the side channels. Using this device, we demonstrate that the movement of neural stem cells can be monitored optically with ease under various chemical conditions, and the experimental results show that the over expression of epidermal growth factor receptors (EGFR) enhances the motility of neural stem cells. Motility of neural stem cells is an important biomarker for assessing cells aggressiveness, thus tumorigenic factor3. Deciphering the mechanism underlying NSC motility will yield insight into both disorders of neural development and into brain cancer stem cell invasion.

We demonstrate that the over expression of epidermal growth factor receptors (EGFR) enhances the motility of neural stem cells(NSCs) using a novel agarose gel based microfluidic device. This technology can be readily adaptable to other mammalian cell systems where cell sources are scarce, such as human neural stem cells, and the turn around time is critical.

使用琼脂糖凝胶为基础的微流体装置的评估神经干细胞的运动

While microfluidic technology is reaching a new level of maturity for macromolecular assays, cell-based assays are still at an infant stage1. This is ...

Protocol for Culturing Sympathetic Neurons from Rat Superior Cervical Ganglia (SCG)

The superior cervical ganglia (SCG) in rats are small, glossy, almond-shaped structures that contain sympathetic neurons.  These neurons provide sympathetic innervations for the head and neck regions and they constitute a well-characterized and relatively homogeneous population (4).  Sympathetic neurons are dependent on nerve growth factor (NGF) for survival, differentiation and axonal growth and the wide-spread availability of NGF facilitates their culture and experimental manipulation (2, 3, 6).  For these reasons, cultured sympathetic neurons have been used in a wide variety of studies including neuronal development and differentiation, mechanisms of programmed and pathological cell death, and signal transduction (1, 2, 5, and 6).  Dissecting out the SCG from newborn rats and culturing sympathetic neurons is not very complicated and can be mastered fairly quickly.  In this article, we will describe in detail how to dissect out the SCG from newborn rat pups and to use them to establish cultures of sympathetic neurons.  The article will also describe the preparatory steps and the various reagents and equipment that are needed to achieve this.

Protocol for Culturing Sympathetic Neurons from Rat Superior Cervical Ganglia SCG

This is a protocol describing how to isolate and culture primary sympathetic neurons from superior cervical ganglia (SCG) of newborn rat pups.

培养大鼠颈上神经节（SCG）的交感神经元的议定书

The superior cervical ganglia (SCG) in rats are small, glossy, almond-shaped structures that contain sympathetic neurons.  These neurons provide ...

Calcium Imaging of Cortical Neurons using Fura-2 AM

Calcium imaging is a common technique that is useful for measuring calcium signals in cultured cells. Calcium imaging techniques take advantage of calcium indicator dyes, which are BAPTA-based organic molecules that change their spectral properties in response to the binding of Ca2+ ions. Calcium indicator dyes fall into two categories, ratio-metric dyes like Fura-2 and Indo-1 and single-wavelength dyes like Fluo-4. Ratio-metric dyes change either their excitation or their emission spectra in response to calcium, allowing the concentration of intracellular calcium to be determined from the ratio of fluorescence emission or excitation at distinct wavelengths.  The main advantage of using ratio-metric dyes over single wavelength probes is that the ratio signal is independent of the dye concentration, illumination intensity, and optical path length allowing the concentration of intracellular calcium to be determined independently of these artifacts. One of the most common calcium indicators is Fura-2, which has an emission peak at 505 nM and changes its excitation peak from 340 nm to 380 nm in response to calcium binding.  Here we describe the use of Fura-2 to measure intracellular calcium elevations in neurons and other excitable cells.

Calcium signals play a key role in many cellular processes including gene expression, survival and differentiation. Here we demonstrate how to perform calcium imaging using Fura-2 AM. Calcium imaging is a valuable tool to study the regulation of intracellular calcium in real time and its regulation of signaling cascades.

使用FURA - 2上午皮层神经元的钙成像

Calcium imaging is a common technique that is useful for measuring calcium signals in cultured cells. Calcium imaging techniques take advantage of calcium ...