作者希望 aknowledge 参与项目不同步骤的同事和人员。在 JRC 卡尔斯鲁厄设计办公室的同事, Knoche 和 Volkmar 欧内斯特, 在 JRC 卡尔斯鲁厄讲习班基督教 Diebold 和 Küst 为实验室的设计和制造阀门 (爱) 歧管和林瓦尔德 GmbH 为停止流检测模式技术的软件实现。

注: 使用设计用于超痕量分析的设备, 采用高纯度水 (18.2 MΩ cm) 制备解决方案。用石英亚沸腾蒸馏装置提纯硝酸。净水系统和次沸蒸馏装置均在洁净室操作。
警告: 90Sr 具有强烈的毒性和致癌性。在进行实验时, 应采取适当的安全措施, 包括工程控制系统和个人防护设备。
1. 实验准备
注意: 有关软件体系结构及其功能的详细说明可在其他地方找到23。
<ol><li>将模块化阀位置出口端口连接到无线电流量检测器的入口端口。</li>
	<li>将触发线连接到选定的探测器。</li>
	<li>确保爱的端口已正确连接。确保为整个协议提供足够数量的工作解决方案, 并且液体取样油管仍将被淹没。</li>
	<li>确保 Autosampler, 启动 Autosampler 软件, 并通过软件接口初始化 Autosampler。单击初始化按钮以生成设备和 PC 之间的通信。</li>
	<li>确保 AutoRAD 软件已启动, 请使用 "选项" 选项卡检查通信端口, 并通过用户界面初始化软件。有关软件图形界面的详细信息, 请参阅讨论部分。</li>
	<li>确保检测软件中的分析序列被编程。通过输入所需的步骤数以及每个设备的任务和速度, 使用 AutoRAD 软件中的方法编辑器选项卡程序视图序列。 注意: 在以前的发布23中可以找到软件操作的详细说明。</li>
	<li>请咨询本地防护人员, 并使用90Sr 为整个过程采用所需的防护测量。</li>
</ol>2. 系统清洗
<ol><li>在 90 mL·min-1上, 从烧瓶中装载10毫升 18.2 MΩ厘米的水。确保将注射器阀位置设置为此步骤的 in 位置. 在这个位置, 加载发生直接到注射器, 而不是通过爱。</li>
	<li>在 90 mL·min-1的流速下, 通过保持线圈将水丢弃到废料中。</li>
	<li>在 3 mL·min-1的流速下, 将3毫升乙醇装载到保温线圈上。将注射器阀位置设置为出。</li>
	<li>将乙醇以 3 mL·min-1的流速降低到探测器线圈。</li>
</ol>3. 对爱的负载树脂
<ol><li>搅拌树脂悬浮在水中 (12 mg·mL-1), 通过爱提取3毫升。将流设置为 3 mL·min-1
</li>
	<li>以 1.2 mL·min-1的流速将树脂悬浮液滴入柱形通道
</li>
	<li>清洗保温线圈, 将树脂残留物放到柱形通道上。为此, 负载9毫升 18.2 MΩ厘米水从烧瓶到注射器的流速为 90 mL·min-1。确保注射器阀位置位于 in 位置. 在 3 mL·min-1的流速下, 通过保持线圈将水丢弃到废料中。</li>
</ol>4. 分析序列
<ol><li>列调节<ol>
<li>将2毫升的 HNO3 (4 米) 通过爱的持有线圈加载。将流设置为 6 mL·min-1。</li>
		<li>将 HNO3拖放到列上, 其流速率为 1.2 mL·min-1。</li>
	</ol>
</li>
	<li>采样的加载和消除干扰<ol>
<li>从 autosampler 到持有线圈的负载样品 (1.3 毫升) 的流速为 6 mL·min-1。</li>
		<li>以 1.2 mL·min-1的流速将示例拖到列上。</li>
		<li>将0.5 毫升的 HNO3 (4 M) 加载到持有线圈, 其流速为 6 mL·min-1。</li>
		<li>用0.5 毫升的 HNO3 (4 米) 冲洗该列, 以洗脱矩阵干扰的速率为 1.2 mL·min-1.</li>
	</ol>
</li>
	<li>样品的洗脱和测量<ol>
<li>将5毫升 18.2 MΩ厘米的水装载到保持线圈上, 流速为 6 mL·min-1。</li>
		<li>触发探测器。将闪烁液体的流速设置为检测器软件中的 2 mL·min-1 。定住到十年代。样品线圈的体积为2毫升。</li>
		<li>冲洗列。</li>
	</ol>
</li>
	<li>取样探头和夹持线圈的冲洗<ol>
<li>将0.6 毫升的 HNO3 (1%) 加载到持有线圈, 其流速为 6 mL·min-1。</li>
		<li>以 6 mL·min-1的流速将0.6 毫升的空气加载到保持线圈上。</li>
		<li>将混合物的1.2 毫升排出废料。</li>
	</ol>
</li>
	<li>树脂置换<ol>
<li>在 3 mL·min-1的流速下, 将0.2 毫升乙醇装载到保温线圈上。</li>
		<li>用0.2 毫升乙醇冲洗柱, 流速为 1.2 mL·min-1。</li>
		<li>用0.5 毫升水冲洗柱通道, 流速为 0.45 mL·min-1。</li>
		<li>将使用过的树脂排出废料。</li>
	</ol>
</li>
</ol>

<ol><li>Zapata-García, D., Wershofen, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Development+of+radiochemical+analysis+strategies+for+decommissioning+activities%5BTitle%5D)+AND+%22Applied+Radiation+and+Isotopes%22%5BJournal%5D)">Development of radiochemical analysis strategies for decommissioning activities.</a> Applied Radiation and Isotopes. 126, 204-207 (2017).</li>
<li>Hou, X. <a target="_blank" href="https://link.springer.com/article/10.1007/s10967-007-0708-x">Radiochemical analysis of radionuclides difficult to measure for waste characterization in decommissioning of nuclear facilities.</a> Journal of Radioanalytical and Nuclear Chemistry. 273 (1), 43-48 (2007).</li>
<li>Chung, K. H., et al. <a target="_blank" href="https://link.springer.com/article/10.1007/s10967-014-3594-z">Rapid determination of radiostrontium in milk using automated radionuclides separator and liquid scintillation counter.</a> Journal of Radioanalytical and Nuclear Chemistry. 304 (1), 293-300 (2015).</li>
<li>Desmartin, P., Kopajtic, Z., Haerdi, W. <a target="_blank" href="https://link.springer.com/article/10.1023/A:1005712218900">Radiostrontium-90 (90Sr) Ultra-Traces Measurements by Coupling Ionic Chromatography (HPIC) and on Line Liquid Scintillation Counting (OLLSC).</a> Environmental Monitoring and Assessment. 44 (1), 413-423 (1997).</li>
<li>Grate, J. W., Strebin, R., Janata, J., Egorov, O., Ruzicka, J. <a target="_blank" href="http://pubs.acs.org/doi/abs/10.1021/ac950561m">Automated Analysis of Radionuclides in Nuclear Waste: Rapid Determination of 90Sr by Sequential Injection Analysis.</a> Analytical Chemistry. 68 (2), 333-340 (1996).</li>
<li>Holmgren, S., Tovedal, A., Björnham, O., Ramebäck, H. <a target="_blank" href="https://www.sciencedirect.com/science/article/pii/S0969804316300112">Time optimization of 90Sr measurements: Sequential measurement of multiple samples during ingrowth of 90Y.</a> Applied Radiation and Isotopes. 110, 150-154 (2016).</li>
<li>Kavasi, N., et al. <a target="_blank" href="https://link.springer.com/article/10.1007/s10967-014-3649-1">Measurement of 90Sr in soil samples affected by the Fukushima Daiichi Nuclear Power Plant accident.</a> Journal of Radioanalytical and Nuclear Chemistry. 303 (3), 2565-2570 (2015).</li>
<li>Kołacińska, K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Automation+of+sample+processing+for+ICP-MS+determination+of+90Sr+radionuclide+at+ppq+level+for+nuclear+technology+and+environmental+purposes%5BTitle%5D)+AND+%22Talanta%22%5BJournal%5D)">Automation of sample processing for ICP-MS determination of 90Sr radionuclide at ppq level for nuclear technology and environmental purposes.</a> Talanta. 169, 216-226 (2017).</li>
<li>Lazare, L., Crestey, C., Bleistein, C. <a target="_blank" href="https://link.springer.com/article/10.1007/s10967-008-7298-0">Measurement of 90Sr in primary coolant of pressurized water reactor.</a> Journal of Radioanalytical and Nuclear Chemistry. 279 (2), 633-638 (2009).</li>
<li>Mola, M., et al. <a target="_blank" href="https://www.sciencedirect.com/science/article/pii/S0969804313005721">Determination of 90Sr and 210Pb in sludge samples using a LOV-MSFIA system and liquid scintillation counting.</a> Applied Radiation and Isotopes. 86, 28-35 (2014).</li>
<li>Plionis, A. A., Gonzales, E. R., Landsberger, S., Peterson, D. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Evaluation+of+flow+scintillation+analysis+for+the+determination+of+Sr-90+in+bioassay+samples%5BTitle%5D)+AND+%22Applied+Radiation+and+Isotopes%22%5BJournal%5D)">Evaluation of flow scintillation analysis for the determination of Sr-90 in bioassay samples.</a> Applied Radiation and Isotopes. 67 (1), 14-20 (2009).</li>
<li>Temba, E. S. C., Reis Júnior, A. S., Amaral, ÂM., Monteiro, R. P. G. <a target="_blank" href="http://link.springer.com/content/pdf/10.1007/s10967-011-1327-0.pdf">Separation and determination of 90Sr in low- and intermediate-level radioactive wastes using extraction chromatography and LSC.</a> Journal of Radioanalytical and Nuclear Chemistry. 290 (3), 631-635 (2011).</li>
<li>Tomita, J., Yamamoto, M., Nozaki, T., Tanimura, Y., Oishi, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Determination+of+low-level+radiostrontium%2C+with+emphasis+on+in+situ+pre-concentration+of+Sr+from+large+volume+of+freshwater+sample+using+Powdex+resin%5BTitle%5D)+AND+%22Journal+of+Environmental+Radioactivity%22%5BJournal%5D)">Determination of low-level radiostrontium, with emphasis on in situ pre-concentration of Sr from large volume of freshwater sample using Powdex resin.</a> Journal of Environmental Radioactivity. 146, 88-93 (2015).</li>
<li>Egorov, O., Grate, J. W., Ruzicka, J. <a target="_blank" href="https://link.springer.com/article/10.1007/BF02389777">Automation of radiochemical analysis by flow injection techniques: Am-Pu separation using TRU-resin™ sorbent extraction column.</a> Journal of Radioanalytical and Nuclear Chemistry. 234 (1), 231-235 (1998).</li>
<li>Rodríguez, R., Avivar, J., Leal, L. O., Cerdà, V., Ferrer, L. <a target="_blank" href="https://www.sciencedirect.com/science/article/pii/S0165993615300522">Strategies for automating solid-phase extraction and liquid-liquid extraction in radiochemical analysis.</a> TrAC Trends in Analytical Chemistry. 76, 145-152 (2016).</li>
<li>Miró, M., Oliveira, H. M., Segundo, M. A. <a target="_blank" href="https://www.sciencedirect.com/science/article/pii/S0165993610002682">Analytical potential of mesofluidic lab-on-a-valve as a front end to column-separation systems.</a> TrAC Trends in Analytical Chemistry. 30 (1), 153-164 (2011).</li>
<li>Kołacińska, K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Automation+of+sample+processing+for+ICP-MS+determination+of+90Sr+radionuclide+at+ppq+level+for+nuclear+technology+and+environmental+purposes%5BTitle%5D)+AND+%22Talanta%22%5BJournal%5D)">Automation of sample processing for ICP-MS determination of 90Sr radionuclide at ppq level for nuclear technology and environmental purposes.</a> Talanta. , (2016).</li>
<li>Rodríguez, R., Avivar, J., Ferrer, L., Leal, L. O., Cerdà, V. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Automated+total+and+radioactive+strontium+separation+and+preconcentration+in+samples+of+environmental+interest+exploiting+a+lab-on-valve+system%5BTitle%5D)+AND+%22Talanta%22%5BJournal%5D)">Automated total and radioactive strontium separation and preconcentration in samples of environmental interest exploiting a lab-on-valve system.</a> Talanta. 96, 96-101 (2012).</li>
<li>Rodríguez, R., et al. <a target="_blank" href="https://www.sciencedirect.com/science/article/pii/S0039914014005359">Automation of 99Tc extraction by LOV prior ICP-MS detection: Application to environmental samples.</a> Talanta. 133, 88-93 (2015).</li>
<li>Villar, M., et al. <a target="_blank" href="https://www.ncbi.nlm.nih.gov/pubmed/23683144">Automatic and Simple Method for 99Tc Determination Using a Selective Resin and Liquid Scintillation Detection Applied to Urine Samples.</a> Analytical Chemistry. 85 (11), 5491-5498 (2013).</li>
<li>L'Annunziata, M. F. <a target="_blank" href="http://scholar.google.com/scholar?hl=en&safe=off&q=author%3aL%27Annunziata%2C+MF+%22Handbook+of+Radioactivity+Analysis%22">Handbook of Radioactivity Analysis</a>. , Third Edition, Academic Press. 1117-1178 (2012).</li>
<li>Roane, J. E., DeVol, T. A., Leyba, J. D., Fjeld, R. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((The+use+of+extraction+chromatography+resins+to+concentrate+actinides+and+strontium+from+soil+for+radiochromatographic+analyses%5BTitle%5D)+AND+%22Journal+of+Environmental+Radioactivity%22%5BJournal%5D)">The use of extraction chromatography resins to concentrate actinides and strontium from soil for radiochromatographic analyses.</a> Journal of Environmental Radioactivity. 66 (3), 227-245 (2003).</li>
<li>Barbesi, D., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((A+LabVIEW%C2%AE-based+software+for+the+control+of+the+AUTORAD+platform%3A+a+fully+automated+multisequential+flow+injection+analysis+Lab-on-Valve+%28MSFIA-LOV%29+system+for+radiochemical+analysis%5BTitle%5D)+AND+%22Journal+of+Radioanalytical+and+Nuclear+Chemistry%22%5BJournal%5D)">A LabVIEW®-based software for the control of the AUTORAD platform: a fully automated multisequential flow injection analysis Lab-on-Valve (MSFIA-LOV) system for radiochemical analysis.</a> Journal of Radioanalytical and Nuclear Chemistry. 313 (1), 217-227 (2017).</li>
<li>Barbesi, D., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((A+LabVIEW%C2%AE-based+software+for+the+control+of+the+AUTORAD+platform%3A+a+fully+automated+multisequential+flow+injection+analysis+Lab-on-Valve+%28MSFIA-LOV%29+system+for+radiochemical+analysis%5BTitle%5D)+AND+%22Journal+of+Radioanalytical+and+Nuclear%22%5BJournal%5D)">A LabVIEW®-based software for the control of the AUTORAD platform: a fully automated multisequential flow injection analysis Lab-on-Valve (MSFIA-LOV) system for radiochemical analysis.</a> Journal of Radioanalytical and Nuclear. , 1-11 (2017).</li>
<li>Strahlenschutz, F. f <a target="_blank" href="http://www.tuev-media.de/produkte/91119-moderne-routine--und-schnellmethoden-zur-bestimmung-von-sr-89-und-sr-90-bei-der-umweltueberwachung.php">Moderne Routine- und Schnellmethoden zur Bestimmung von SR-89 und SR-90 bei der Umweltüberwachung : Bericht einer Ad-hoc-Arbeitsgruppe des Arbeitskreises Umweltüberwachung (AKU)</a>. , Fachverband für Strahlenschutz e.V. (2008).</li>
<li>Currie, L. A. <a target="_blank" href="http://pubs.acs.org/doi/abs/10.1021/ac60259a007">Limits for qualitative detection and quantitative determination. Application to radiochemistry.</a> Analytical Chemistry. 40 (3), 586-593 (1968).</li>
</ol>

作者没有什么可透露的。

放射性特征和保护是核设施生命周期所有阶段的关键问题。核设施退役期间需要进行放射性核素测定, 需要不断改进分析程序。这需要提高选择性和灵敏度, 缩短分析时间。AUTORAD 原型满足了这些要求。此外, 该原型是便携的, 并允许现场确定。建议的自动在线方法成功地应用于测定水样品中的90Sr 活动。
图 1显示了 AutoRAD 系统的示意图。使用商用图形编程语言 LabVIEW 2014 实现了与原型的通信。部署了用于配置、编程和控制接口的虚拟仪器软件体系结构 (VISA) 模式。图 2显示了图形用户界面屏幕, 在系统初始化之前可以验证端口配置。签证模式在操作系统和程序环境上是独立的, 因此提供了特殊的通用性。已开发的软件的基本结构和特点在以前的出版物24中得到了广泛的讨论。通过使用 RS232 接口控制 PC 机的滴定管, 实现了改进, 从而允许同时加强对两滴定管的控制, 以及在停止流模式下进行测量的可能性。相反, 当系统背压增加时, RS232 连接会迅速反应。这可能导致系统错误和测量停止。因此, 在树脂的加载过程中, 必须特别注意样品的离子强度。
用锶稳定同位素86sr 作为放射性90sr 的代理, 并将 AUTORAD 系统耦合到 ICP-MS 而不是 beta detctcor, 实现了实验条件的优化。系统。图 3显示了 ICP-MS 86Sr 洗脱配置文件。获得的86Sr 洗脱配置文件与以前报告的总锶使用低压分离设备25的结果完全一致, 并已被减去空白。采用最小二乘法线性回归法生成不引入额外不确定分量的目的曲线拟合。所得到的线性度为 0.995, 与p值小于意义水平。2 pg·g-1的 LOD 是根据柯里26对空白的重复测量确定的。该方法的重现性基于峰值面积的相对标准偏差, 根据三次重复运行计算, 在10到 120 pg·g-1的范围内始终小于4%。在洗脱剖面中目击的肩部最有可能是由于自动 AUTORAD 配置中列的非最佳包装造成的。
图 4显示了使用无线电流量检测器的90Sr 配置文件。AUTORAD 系统能够有效地在水样品中分离90Sr。
图 5显示了90Sr 浓度与信号在感兴趣范围内是线性的依赖性。导出的检测限制在成品中。g-1范围, 启用, 不作进一步修改, 在核退役和废物表征样品中确定放射性锶。该方法的重现性, 利用流闪烁探测器, 并根据峰值面积的相对标准偏差, 在研究的浓度范围内约为30%。然而, 目前的原型设置限制了它在环境样品中的应用, 这主要是由于探测器的时间数很短。此外, 复杂的矩阵可能饱和的树脂在迷你柱。
在测量过程中, 哈密顿和无线电流量检测器泵停止流动的技术将被实现。这项功能将延长停留时间在样品区域的最大的部分在流动细胞之内, 提高灵敏度。因此, 在样本退出检测器之前, acculated 有统计学意义的信号。这种方法将改进计数统计和检测限制。此外, 正在开发一个新的应用, 其中包括一个额外的离子交换小柱, 用于去除可能影响复杂基质样品中不同放射性核素的保留和分离的基质元件。

大约150个商业核电厂正在退役, 但如果将研究和再加工设施考虑到1, 核设施的总数量就会大得多。核设施退役非常昂贵, 涉及运输和关闭污染材料的现场测量。通过采用现场和灵活的测量技术1可以节省开支。因此, 迫切需要迅速提供支持旧核设施退役的现场分析方法。伽玛发射器可以很容易和有选择地确定使用伽玛光谱学, 但在现场分析的方法, 难以测量 (HTM) 放射性核素2。在 HTM 中, 90Sr 由于其毒性和高能量排放引起了极大的兴趣。它的决心是耗时的, 需要分离从干扰和量化使用或分光光度法3,4,5,6,7, 8,9,10,11,12,13。
标准的放射化学方法费时费力, 通常需要重复才能获得足够的锶产量。因此, 迫切需要更快、更准确的方法。除标准分离协议外, 流动注射技术还适用于放射性同位素5、14、15的纯化和/或预浓缩。实验室阀门 (爱) 装置是流动技术的进一步发展。它们是可编程的、基于流的平台, 具有不同的耦合模式, 并且具有高通用性16。这种装置允许在检测之前自动分离和预浓缩分析器, 从而增加再现性和重复性8,17,18,19。与 multisyringe 流泵耦合的爱系统被广泛用于检测放射性核素, 因为试剂消耗和废物产生的最小化8,10,17,18,19,20. 然而, 关于超微量水平在线检测的报告研究是稀疏817。
放射性材料的现场测量有许多优点和优点, 但在90Sr 监视中没有应用流闪烁。基本上, 量化是使用在线检测器, 混合的洗脱液来自爱的设备与闪烁鸡尾酒11, 21, 22.然后通过计数单元泵浦混合物, 用配对光电倍增管进行测量。由于单元格体积小, 测量时间为秒刻度。
本研究的目的是开发一种全自动的在线锶检测方法, 其范围广泛, 涵盖了与环境有关的浓度, 也包括在核工业废料流中发现的。该平台是移动的, 可以安装在车辆上进行水样品的现场分析。

<table><tbody><tr><td>microLAB 600 series</td><td>Hamilton</td><td>ML600EE6910</td><td>Two dual syringe pump system, equiped with two 10 mL glass syringes. The instruments are interconnected using the CAN port (daisy chain).</td></tr><tr><td>FlowLogic U</td><td>LabLogic</td><td>SG-BXX-05</td><td>Liquid scintillator with high flash point</td></tr><tr><td>&amp;szlig;-RAM 5</td><td>LabLogic</td><td></td><td>flow detector, 2000 &amp;mu;L coiled Teflon flow cell.Software Laura 4.2.8 (LabLogic, England) run on desktop PC and connected to the detector via USB</td></tr><tr><td>SC-&amp;mu; DX Autosampler</td><td>Elemental Scientific Instruments (ESI)</td><td></td><td></td></tr><tr><td>Cheminert selector</td><td>Valco Instruments Co. Inc.</td><td></td><td>in-house made Lab-on-Valve has been mounted on this selector</td></tr><tr><td>Modular Valve&lt;br/&gt; Positioner (MVP)</td><td>Hamilton</td><td></td><td></td></tr><tr><td>mini magnetic stirrer</td><td>IKA</td><td></td><td></td></tr><tr><td>Nitric Acid Suprapur 65%</td><td>Merck</td><td>1.00441.1000</td><td>purified using quartz sub-boiling distillation unit</td></tr><tr><td>Sr-resin</td><td>Eichchrom Tecnologies, Inc</td><td>SR-B100-A</td><td>particle size 100-150 &amp;micro;m</td></tr><tr><td>Water system Elix 3 in combination with Mili-Q Element A10</td><td>Millipore</td><td></td><td>high-purity water (18.2 M&amp;Omega; cm)</td></tr><tr><td>Sr-90 standard</td><td>Eckert &amp;amp; Ziegler</td><td>7090</td><td>Sr-90 concentration 1.915 kBq/g &amp;plusmn; 3.0%, reference date 15-May-2016 12:00 PST</td></tr><tr><td>MLS quartz sub-boiling distillation unit</td><td>MLS GmbH</td><td></td><td>Subboiling unit for the purification of HCl and nitric acid</td></tr></tbody></table>

automated 90sr separation and preconcentration in a lab-on-valve system at ppq level

开发了一种快速、自动化、便携的水样品中放射性锶的分离和测定系统, 采用 Sr 树脂和多序贯流注入分析法。放射性锶的浓度由流动闪烁计数确定, 允许在线和现场确定。该系统可在工业相关水平上确定放射性锶, 而无需进一步修改, 使用的总分析时间为每水样品少于10分钟。检测的限制为 320 fg·g-1 (1.7)。

开发并实现了由自制的基于 LabVIEW 的软件操作的全自动 AUTORAD 平台 (图 1)。该软件允许在用户友好的环境中为日常操作提供足够的灵活性 (图 2)。通过将该平台与不同的检测器 (图 3) 耦合在一起, 也证明了该系统的通用性。该方法的适用性已在含90Sr 标准 (图 4) 的水样中显示。对参数的线性度、线性范围、检测极限 (LOD) 和重复性进行了评估 (图 5)。
<img alt="Figure 1" class="xfigimg" src="/files/ftp_upload/57722/57722fig1.jpg"> 图1。显示端口配置和使用试剂的 AutoRAD 系统的示意图表示。中心端口通过保持线圈 (10 毫升) 连接到注射器泵;在房子里制造了甲基丙烯酸酯。<a href="/files/ftp_upload/57722/57722fig1large.jpg" target="_blank">请单击此处查看此图的较大版本.</a>
<img alt="Figure 2" class="xfigimg" src="/files/ftp_upload/57722/57722fig2.jpg"> 图2。AutoRAD 软件选项菜单.右下角区域显示分配的端口。通过 "向下滚动" 菜单, 用户可以在分配中进行更改。<a href="/files/ftp_upload/57722/57722fig2large.jpg" target="_blank">请单击此处查看此图的较大版本.</a>
<img alt="Figure 3" class="xfigimg" src="/files/ftp_upload/57722/57722fig3.jpg"> 图3。86采用电感耦合等离子体质谱 (ICP-MS) 作为探测器的 Sr 洗脱峰.在洗脱的第一个100s 中, 锶从柱体中洗脱定量。<a href="/files/ftp_upload/57722/57722fig3large.jpg" target="_blank">请单击此处查看此图的较大版本.</a>
<img alt="Figure 4" class="xfigimg" src="/files/ftp_upload/57722/57722fig4.jpg"> 图4。34.5 @ 1 90Sr (6.6 pg·g-1) 洗脱峰使用ß RAM 5 作为探测器.居住时间在卷是四十年代。建议的90Sr 方法的总体恢复率为 70% 5%。<a href="/files/ftp_upload/57722/57722fig4large.jpg" target="_blank">请单击此处查看此图的较大版本.</a>
<img alt="Figure 5" class="xfigimg" src="/files/ftp_upload/57722/57722fig5.jpg"> 图5。计数率与放射性锶浓度的校准曲线。获得了良好的线性度 (R2 = 0.997)。检测限制被计算为 320 fg·g-1 5 (1.7), 由三点三乘以空白的标准偏差。<a href="/files/ftp_upload/57722/57722fig5large.jpg" target="_blank">请单击此处查看此图的较大版本.</a>

Watch this Scientific Journal Video about Automated 90Sr Separation and Preconcentration in a Lab-on-Valve System at Ppq Level at JoVE.com

Automated 90Sr Separation and Preconcentration in a Lab-on-Valve System at Ppq Level

Ppq 级实验室系统中的自动90Sr 分离和预富集

在这里, 我们提出了便携式 autoRAD 平台快速辐射分离和确定的90Sr, 一个重要的裂变产品高度相关的核废料。

A quick, automated and portable system for the separation and determination of radiostrontium in aqueous samples, using Sr-resin and multi sequential flow ...

automated-90sr-separation-preconcentration-lab-on-valve-system-at-ppq

Research

Education

JoVE Journal

JoVE Core

Chemistry

Automated 90Sr Separation and Preconcentration in a Lab-on-Valve System at Ppq Level

Atoms and Elements

SCIENTISTS IN ACTION

8.0K 次观看.  European Commission, DG Joint Research Centre - JRC. 在这里, 我们提出了便携式 autoRAD 平台快速辐射分离和确定的90Sr, 一个重要的裂变产品高度相关的核废料。

视频: Automated 90Sr Separation and Preconcentration in a Lab-on-Valve System at Ppq Level

Radiolabeling and Quantification of Cellular Levels of Phosphoinositides by High Performance Liquid Chromatography-coupled Flow Scintillation

Phosphoinositides (PtdInsPs) are essential signaling lipids responsible for recruiting specific effectors and conferring organelles with molecular identity and function. Each of the seven PtdInsPs varies in their distribution and abundance, which are tightly regulated by specific kinases and phosphatases. The abundance of PtdInsPs can change abruptly in response to various signaling events or disturbance of the regulatory machinery. To understand how these events lead to changes in the amount of PtdInsPs and their resulting impact, it is important to quantify PtdInsP levels before and after a signaling event or between control and abnormal conditions. However, due to their low abundance and similarity, quantifying the relative amounts of each PtdInsP can be challenging. This article describes a method for quantifying PtdInsP levels by metabolically labeling cells with 3H-myo-inositol, which is incorporated into PtdInsPs. Phospholipids are then precipitated and deacylated. The resulting soluble 3H-glycero-inositides are further extracted, separated by high-performance liquid chromatography (HPLC), and detected by flow scintillation. The labeling and processing of yeast samples is described in detail, as well as the instrumental setup for the HPLC and flow scintillator. Despite losing structural information regarding acyl chain content, this method is sensitive and can be optimized to concurrently quantify all seven PtdInsPs in cells.

Phosphoinositides are signaling lipids whose relative abundance rapidly changes in response to various stimuli. This article describes a method to measure the abundance of phosphoinositides by metabolically labeling cells with 3H-myo-inositol, followed by extraction and deacylation. Extracted glycero-inositides are then separated by high-performance liquid chromatography and quantified by flow scintillation.

放射性标记和磷酸肌醇的细胞水平的定量高效液相色谱耦合流动闪烁

Phosphoinositides (PtdInsPs) are essential signaling lipids responsible for recruiting specific effectors and conferring organelles with molecular ...

科研

化学

Quantification of Hydrogen Concentrations in Surface and Interface Layers and Bulk Materials through Depth Profiling with Nuclear Reaction Analysis

Nuclear reaction analysis (NRA) via the resonant 1H(15N,&#945;&#947;)12C reaction is a highly effective method of depth profiling that quantitatively and non-destructively reveals the hydrogen density distribution at surfaces, at interfaces, and in the volume of solid materials with high depth resolution. The technique applies a 15N ion beam of 6.385 MeV provided by an electrostatic accelerator and specifically detects the 1H isotope in depths up to about 2 &#956;m from the target surface. Surface H coverages are measured with a sensitivity in the order of ~1013 cm-2 (~1% of a typical atomic monolayer density) and H volume concentrations with a detection limit of ~1018 cm-3 (~100 at. ppm). The near-surface depth resolution is 2-5 nm for surface-normal 15N ion incidence onto the target and can be enhanced to values below 1 nm for very flat targets by adopting a surface-grazing incidence geometry. The method is versatile and readily applied to any high vacuum compatible homogeneous material with a smooth surface (no pores). Electrically conductive targets usually tolerate the ion beam irradiation with negligible degradation. Hydrogen quantitation and correct depth analysis require knowledge of the elementary composition (besides hydrogen) and mass density of the target material. Especially in combination with ultra-high vacuum methods for in-situ target preparation and characterization, 1H(15N,&#945;&#947;)12C NRA is ideally suited for hydrogen analysis at atomically controlled surfaces and nanostructured interfaces. We exemplarily demonstrate here the application of 15N NRA at the MALT Tandem accelerator facility of the University of Tokyo to (1) quantitatively measure the surface coverage and the bulk concentration of hydrogen in the near-surface region of a H2 exposed Pd(110) single crystal, and (2) to determine the depth location and layer density of hydrogen near the interfaces of thin SiO2 films on Si(100).

We illustrate the application of 1H(15N,&#945;&#947;)12C resonant nuclear reaction analysis (NRA) to quantitatively evaluate the density of hydrogen atoms on the surface, in the volume, and at an interfacial layer of solid materials. The near-surface hydrogen depth profiling of a Pd(110) single crystal and of SiO2/Si(100) stacks is described.

通过与核反应分析深度剖面的表面和界面层和颗粒材料氢含量的定量

Nuclear reaction analysis (NRA) via the resonant 1H(15N,&#945;&#947;)12C reaction is a highly effective method of depth profiling that quantitatively and ...

工程学

In Situ Detection and Single Cell Quantification of Metal Oxide Nanoparticles Using Nuclear Microprobe Analysis

Micro-analytical techniques based on chemical element imaging enable the localization and quantification of chemical composition at the cellular level. They offer new possibilities for the characterization of living systems and are particularly appropriate for detecting, localizing and quantifying the presence of metal oxide nanoparticles both in biological specimens and the environment. Indeed, these techniques all meet relevant requirements in terms of (i) sensitivity (from 1 up to 10 &#181;g.g-1 of dry mass), (ii) micrometer range spatial resolution, and (iii) multi-element detection. Given these characteristics, microbeam chemical element imaging can powerfully complement routine imaging techniques such as optical and fluorescence microscopy. This protocol describes how to perform a nuclear microprobe analysis on cultured cells (U2OS) exposed to titanium dioxide nanoparticles. Cells must grow on and be exposed directly in a specially designed sample holder used on the optical microscope and in the nuclear microprobe analysis stages. Plunge-freeze cryogenic fixation of the samples preserves both the cellular organization and the chemical element distribution. Simultaneous nuclear microprobe analysis (scanning transmission ion microscopy, Rutherford backscattering spectrometry and particle induced X-ray emission) performed on the sample provides information about the cellular density, the local distribution of the chemical elements, as well as the cellular content of nanoparticles. There is a growing need for such analytical tools within biology, especially in the emerging context of Nanotoxicology and Nanomedicine for which our comprehension of the interactions between nanoparticles and biological samples must be deepened. In particular, as nuclear microprobe analysis does not require nanoparticles to be labelled, nanoparticle abundances are quantifiable down to the individual cell level in a cell population, independently of their surface state.

In Situ Detection and Single Cell Quantification of Metal Oxide Nanoparticles Using Nuclear Microprobe Analysis

We describe a procedure for the detection of chemical elements present in situ in human cells as well as their in vitro quantification. The method is well-suited to any cell type and is particularly useful for quantitative chemical analyses in single cells following in vitro metal oxide nanoparticles exposure.

原位金属氧化物纳米粒子的核探针检测与单细胞定量研究

Micro-analytical techniques based on chemical element imaging enable the localization and quantification of chemical composition at the cellular level. ...

Preparation and Evaluation of 99mTc-labeled Tridentate Chelates for Pre-targeting Using Bioorthogonal Chemistry

Pre-targeting combined with bioorthogonal chemistry is emerging as an effective way to create new radiopharmaceuticals. Of the methods available, the inverse electron demand Diels-Alder (IEDDA) cycloaddition between a radiolabeled tetrazines and trans-cyclooctene (TCO) linked to a biomolecule has proven to be a highly effective bioorthogonal approach to imaging specific biological targets. Despite the fact that technetium-99m remains the most widely used isotope in diagnostic nuclear medicine, there is a scarcity of methods for preparing 99mTc-labeled tetrazines. Herein we report the preparation of a family of tridentate-chelate-tetrazine derivatives and their Tc(I) complexes. These hitherto unknown compounds were radiolabeled with 99mTc using a microwave-assisted method in 31% to 83% radiochemical yield. The products are stable in saline and PBS and react rapidly with TCO derivatives in vitro. Their in vivo pre-targeting abilities were demonstrated using a TCO-bisphosphonate (TCO-BP) derivative that localizes to regions of active bone metabolism or injury. In murine studies, the 99mTc-tetrazines showed high activity concentrations in knees and shoulder joints, which was not observed when experiments were performed in the absence of TCO-BP. The overall uptake in non-target organs and pharmacokinetics varied greatly depending on the nature of the linker and polarity of the chelate.

Preparation and Evaluation of 99mTc-labeled Tridentate Chelates for Pre-targeting Using Bioorthogonal Chemistry

Here, we describe a protocol for radiolabeling and in vivo testing of tridentate 99mTc(I) chelate-tetrazine derivatives for pre-targeting and bioorthogonal chemistry.

制备和评价<sup&gt;99米</sup&gt;锝标记的三齿螯合物预靶向使用生物正交化学

Pre-targeting combined with bioorthogonal chemistry is emerging as an effective way to create new radiopharmaceuticals. Of the methods available, the ...

Automation of a Positron-emission Tomography (PET) Radiotracer Synthesis Protocol for Clinical Production

The development of new positron-emission tomography (PET) tracers is enabling researchers and clinicians to image an increasingly wide array of biological targets and processes. However, the increasing number of different tracers creates challenges for their production at radiopharmacies. While historically it has been practical to dedicate a custom-configured radiosynthesizer and hot cell for the repeated production of each individual tracer, it is becoming necessary to change this workflow. Recent commercial radiosynthesizers based on disposable cassettes/kits for each tracer simplify the production of multiple tracers with one set of equipment by eliminating the need for custom tracer-specific modifications. Furthermore, some of these radiosynthesizers enable the operator to develop and optimize their own synthesis protocols in addition to purchasing commercially-available kits. In this protocol, we describe the general procedure for how the manual synthesis of a new PET tracer can be automated on one of these radiosynthesizers and validated for the production of clinical-grade tracers. As an example, we use the ELIXYS radiosynthesizer, a flexible cassette-based radiochemistry tool that can support both PET tracer development efforts, as well as routine clinical probe manufacturing on the same system, to produce [18F]Clofarabine ([18F]CFA), a PET tracer to measure in vivo deoxycytidine kinase (dCK) enzyme activity. Translating a manual synthesis involves breaking down the synthetic protocol into basic radiochemistry processes that are then translated into intuitive chemistry &#34;unit operations&#34; supported by the synthesizer software. These operations can then rapidly be converted into an automated synthesis program by assembling them using the drag-and-drop interface. After basic testing, the synthesis and purification procedure may require optimization to achieve the desired yield and purity. Once the desired performance is achieved, a validation of the synthesis is carried out to determine its suitability for the production of the radiotracer for clinical use.

Automation of a Positron-emission Tomography PET Radiotracer Synthesis Protocol for Clinical Production

Positron-emission tomography (PET) imaging sites that are involved in multiple early clinical research trials need robust and versatile radiotracer manufacturing capabilities. Using the radiotracer [18F]Clofarabine as an example, we illustrate how to automate the synthesis of a radiotracer using a flexible, cassette-based radiosynthesizer and validate the synthesis for clinical use.

用于临床生产的正电子发射层析成像 (PET) 放射性同位素示踪合成协议的自动化

The development of new positron-emission tomography (PET) tracers is enabling researchers and clinicians to image an increasingly wide array of biological ...

Preparing an Isotopically Pure 229Th Ion Beam for Studies of 229mTh

A methodology is described to generate an isotopically pure 229Th ion beam in the 2+ and 3+ charge states. This ion beam enables one to investigate the low-lying isomeric first excited state of 229Th at an excitation energy of about 7.8(5) eV and a radiative lifetime of up to 104 seconds. The presented method allowed for a first direct identification of the decay of the thorium isomer, laying the foundations to study its decay properties as prerequisite for an optical control of this nuclear transition. High energy 229Th ions are produced in the &#945;&#160;decay of a radioactive 233U source. The ions are thermalized in a buffer-gas stopping cell, extracted and subsequently an ion beam is formed. This ion beam is mass purified by a quadrupole-mass separator to generate a pure ion beam. In order to detect the isomeric decay, the ions are collected on the surface of a micro-channel plate detector, where electrons, as emitted in the internal conversion decay of the isomeric state, are observed.

Preparing an Isotopically Pure 229Th Ion Beam for Studies of 229mTh

We present a protocol for the generation of an isotopically purified low-energy 229Th ion beam from a 233U source. This ion beam is used for the direct detection of the 229mTh ground-state decay via the internal-conversion decay channel. We also measure the internal conversion lifetime of 229mTh as well.

为229mTh的研究准备一个同位素纯229Th Ion光束

A methodology is described to generate an isotopically pure 229Th ion beam in the 2+ and 3+ charge states. This ion beam enables one to investigate the ...

Technical Aspect of the Automated Synthesis and Real-Time Kinetic Evaluation of [11C]SNAP-7941

Positron emission tomography (PET) is an essential molecular imaging technique providing insights into pathways and using specific targeted radioligands for in vivo investigations. Within this protocol, a robust and reliable remote-controlled radiosynthesis of [11C]SNAP-7941, an antagonist to the melanin-concentrating hormone receptor 1, is described. The radiosynthesis starts with cyclotron produced [11C]CO2 that is subsequently further reacted via a gas-phase transition to [11C]CH3OTf. Then, this reactive intermediate is introduced to the precursor solution and forms the respective radiotracer. Chemical as well as the radiochemical purity are determined by means of RP-HPLC, routinely implemented in the radiopharmaceutical quality control process. Additionally, the molar activity is calculated as it is a necessity for the following real-time kinetic investigations. Furthermore, [11C]SNAP-7941 is applied to MDCKII-WT and MDCKII-hMDR1 cells for evaluating the impact of P-glycoprotein (P-gp) expression on cell accumulation. For this reason, the P-gp expressing cell line (MDCKII-hMDR1) is either used without or with blocking prior to experiments by means of the P-gp substrate (&#177;)-verapamil and the results are compared to the ones observed for the wildtype cells. The overall experimental approach demonstrates the importance of a precise time-management that is essential for every preclinical and clinical study using PET tracers radiolabelled with short-lived nuclides, such as carbon-11 (half-life: 20 min).

Technical Aspect of the Automated Synthesis and Real-Time Kinetic Evaluation of [11C]SNAP-7941

Here, we represent a protocol for the fully automated radiolabelling of [11C]SNAP-7941 and the analysis of the real-time kinetics of this PET-tracer on P-gp expressing and non-expressing cells.

[11C_SNAP-7941] 自动合成和实时动力学评估的技术方面

Positron emission tomography (PET) is an essential molecular imaging technique providing insights into pathways and using specific targeted radioligands ...

Radiosynthesis of 1-(2-[18F]Fluoroethyl)-L-Tryptophan using a One-pot, Two-step Protocol

The kynurenine pathway (KP) is a primary route for tryptophan metabolism. Evidence strongly suggests that metabolites of the KP play a vital role in tumor proliferation, epilepsy, neurodegenerative diseases, and psychiatric illnesses due to their immune-modulatory, neuro-modulatory, and neurotoxic effects. The most extensively used positron emission tomography (PET) agent for mapping tryptophan metabolism, &#945;-[11C]methyl-L-tryptophan ([11C]AMT), has a short half-life of 20 min with laborious radiosynthesis procedures. An onsite cyclotron is required to radiosynthesize [11C]AMT. Only a limited number of centers produce [11C]AMT for preclinical studies and clinical investigations. Hence, the development of an alternative imaging agent that has a longer half-life, favorable in vivo kinetics, and is easy to automate is urgently needed. The utility and value of 1-(2-[18F]fluoroethyl)-L-tryptophan, a fluorine-18-labeled tryptophan analog, has been reported in preclinical applications in cell line-derived xenografts, patient-derived xenografts, and transgenic tumor models.
This paper presents a protocol for the radiosynthesis of 1-(2-[18F]fluoroethyl)-L-tryptophan using a one-pot, two-step strategy. Using this protocol, the radiotracer can be produced in a 20 &#177; 5% (decay corrected at the end of synthesis, n &#62; 20) radiochemical yield, with both radiochemical purity and enantiomeric excess of over 95%. The protocol features a small precursor amount with no more than 0.5 mL of reaction solvent in each step, low loading of potentially toxic 4,7,13,16,21,24-hexaoxa-1,10-diazabicyclo[8.8.8]hexacosane (K222), and an environmentally benign and injectable mobile phase for purification. The protocol can be easily configured to produce 1-(2-[18F]fluoroethyl)-L-tryptophan for clinical investigation in a commercially available module.

Radiosynthesis of 1-2-[18F]Fluoroethyl-L-Tryptophan using a One-pot, Two-step Protocol

Here, we describe the radiosynthesis of 1-(2-[18F]Fluoroethyl)-L-tryptophan, a positron emission tomography imaging agent for studying tryptophan metabolism, using a one-pot, two-step strategy in a radiochemistry synthesis system with good radiochemical yields, high enantiomeric excess, and high reliability.

1-（2-[18F]氟乙基）-L-色氨酸的放射性合成，采用一锅两步实验方案

The kynurenine pathway (KP) is a primary route for tryptophan metabolism. Evidence strongly suggests that metabolites of the KP play a vital role in tumor ...

<meta charset="utf8"></head><body>异种移植模型中 68个 Ga 标记纳米抗体的放射合成和 PET/CT 成像

Radiosynthesis, Quality Control, and Small Animal Positron Emission Tomography Imaging of 68Ga-Labelled Nano Molecules

Small animal Positron Emission Tomography (PET) and Single Photon Emission Computed Tomography (SPECT) imaging techniques are crucial in preclinical cancer research, necessitating meticulous attention to radiotracer synthesis, quality assurance, and in vivo injection protocols. This study presents a comprehensive workflow tailored to enhance the robustness and reproducibility of small animal PET experiments. The synthesis process in the radiochemistry laboratory using 68Ga is detailed, highlighting stringent quality control and assurance protocols for each radiotracer production. Parameters such as concentration, molar activity, pH, and purity are rigorously monitored, aligning with standards applicable to human studies. This methodology introduces streamlined syringe preparation and a custom-designed 30G cannula for precise intravenous injections into mice. Monitoring of animal health during scanning, including temperature and heart rate, ensures their well-being throughout the procedure. Dosages for PET and SPECT scans are predetermined to balance data acquisition with minimizing radiation exposure to animals and researchers. Similarly, CT scans employ pre-programmed settings to limit radiation exposure, especially pertinent in long-term studies assessing treatment effects. By optimizing these steps, the workflow aims to standardize procedures, reduce variability, and enhance the quality of small animal PET/SPECT/CT imaging. This resource provides valuable insights for researchers seeking to improve the accuracy and reliability of preclinical investigations in molecular imaging, ultimately advancing the field.

<meta charset="utf8"></head><body>68个 Ga-labeled Nano 分子的放射性合成、质量控制和小动物正电子发射断层扫描成像

This paper describes the radiosynthesis, formulation, quality control of a new radiolabeled probe (i.e., 68Ga-labeled nanobody NM-02), and its use for small animal PET/CT imaging in a xenograft model.

68个 Ga-labeled Nano 分子的放射性合成、质量控制和小动物正电子发射断层扫描成像

Small animal Positron Emission Tomography (PET) and Single Photon Emission Computed Tomography (SPECT) imaging techniques are crucial in preclinical ...

Ppq 级实验室系统中的自动⁹⁰Sr 分离和预富集

摘要

探索更多视频

放射性标记和磷酸肌醇的细胞水平的定量高效液相色谱耦合流动闪烁

通过与核反应分析深度剖面的表面和界面层和颗粒材料氢含量的定量

原位金属氧化物纳米粒子的核探针检测与单细胞定量研究

制备和评价

用于临床生产的正电子发射层析成像 (PET) 放射性同位素示踪合成协议的自动化

^为229mTh的研究准备一个同位素^纯229Th Ion光束

[¹¹C_SNAP-7941] 自动合成和实时动力学评估的技术方面

1-（2-[^18F]氟乙基）-L-色氨酸的放射性合成，采用一锅两步实验方案

⁶⁸个 Ga-labeled Nano 分子的放射性合成、质量控制和小动物正电子发射断层扫描成像

⁶⁸个 Ga-labeled Nano 分子的放射性合成、质量控制和小动物正电子发射断层扫描成像