El estudio fue apoyado por la Fundación Artères, la Fundación Astellas Europa y la Fundación Boninchi. CT fue apoyado por la Fundación Nacional de Ciencia de Suiza (subvención SCORE 3232230-126233).

1. Mango: Diseño y Definición <ol><li> Proteger una hoja de bisturí N º 10 de carbono en una tabla de madera con una cinta. </li><li> Marque el centro del ring en el microscopio. Debe estar ubicado 1,2 cm recta desde el bosque de la hoja de bisturí. </li><li> Taladre un agujero de 2 mm con una broca de diamante esférica, montado en un taladro de alta velocidad. </li><li> Ampliar el agujero con fusiforme o pedacitos de diamante cónica. El diámetro final varía de acuerdo con el peso de la rata como se muestra en la Tabla 1. </li><li> El diseño de la forma del mango con un marcador permanente. Figuras 1 y 2 se pueden utilizar como plantillas. </li><li> Convertir el taladro en una amoladora de banco pequeño y quitar la parte de la hoja fuera de la forma. </li><li> Para rematar la pieza con una baja velocidad de cepillo giratorio. </li></ol> 2. Approximator: Diseño y Definición <ol><li> El aproximador se obtiene mediante la modificación de Klemmer quirúrgica recta o pinza de Kochers. </li><li> Cortar la mitad de una rama en el microscopio utilizando el mini amoladora de banco de alta velocidad. </li><li> Hacer ranuras simétricas a ambos lados para permitir el asa para introducir por completo. </li><li> Haga un corte longitudinal en el brazo largo y compruebe que el centro del brazo largo y un mango bien posicionados se encuentran en un mismo eje. </li><li> Diseñar una muesca en el brazo largo mirando hacia el centro de la empuñadura. </li><li> Hacer la rama lo más fina posible y completan la pieza con la baja velocidad del cepillo giratorio. </li></ol> 3. Puños: Diseño y Definición <ol><li> Gemelos pinzas varían de acuerdo con el peso de la rata y la tensión. Por el contrario, su longitud debe mantenerse alrededor de 4 mm. </li><li> Tome un tubo de polietileno de calibre fino y redondo fuera de un borde con un bisturí N º 10. </li><li> Diseñar una arboleda 0,5 mm desde el borde y corte cuidadosamente una pendiente de bajar a la arboleda. </li><li> Cortar una o dos muescas de espesor total en la tubería. Estos seayudar a la manipulación de la banda durante la preparación del injerto y trasplante. </li><li> Cortar el brazalete a 4 mm a partir de su borde. </li></ol>

<ol>
	<li>Oldani, G., Lacotte, S., Morel, P., Mentha, G., Toso, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Orthotopic+Liver+Transplantation+in+Rats.">Orthotopic Liver Transplantation in Rats.</a> J. Vis. Exp. (65), e4143 (2012).</li><li>Hori, T., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Comprehensive+and+innovative+techniques+for+liver+transplantation+in+rats:+A+surgical+guide.">Comprehensive and innovative techniques for liver transplantation in rats: A surgical guide.</a> World Journal of Gastroenterology., WJG. 16, 3120 (2010).</li><li>Kashfi, A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+review+of+various+techniques+of+orthotopic+liver+transplantation+in+the+rat.">A review of various techniques of orthotopic liver transplantation in the rat.</a> Transplantation Proceedings. 37 (1), 185-188 (2005).</li><li>Kamada, N., Calne, R. Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Orthotopic+liver+transplantation+in+the+rat.+Technique+using+cuff+for+portal+vein+anastomosis+and+biliary+drainage.">Orthotopic liver transplantation in the rat. Technique using cuff for portal vein anastomosis and biliary drainage.</a> Transplantation. 28, 47 (1979).</li><li>Oldani, G., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+novel+technique+for+rat+liver+transplantation+using+Quick+Linker+system:+a+preliminary+result.">A novel technique for rat liver transplantation using Quick Linker system: a preliminary result.</a> Journal of Surgical Research. 149, 303-309 (2008).</li></ol>

Los autores no tienen nada que revelar.

En el presente informe se describe el diseño y construcción del sistema de quick-enlazador para el trasplante de hígado de rata más fácil. Trasplante de hígado de rata es un modelo popular entre 125-180 documentos relacionados que se publican anualmente desde la década de 1990 ( <a href="http://www.pubmed.com" target="_blank">www.pubmed.com</a> ). Además, permite una amplia gama de experimentos, incluyendo la exploración de aspectos de la preservación inmunológicos y de injerto. El uso del kit &quot;rápida-enlazador&quot; permite la anastomosis más fácil y más rápido con garantía de contacto de la íntima-a-íntima. Una descripción detallada y la discusión de los pasos técnicos de un trasplante de hígado de rata se han descrito anteriormente 1. El kit de rápido enlazador se puede construir a bajo precio de material común de laboratorio. El principal desafío encontrado se ha relacionado la ruptura de un mango durante el cepillado final, y ese problema se ha resuelto mediante el establecimiento de la nominal más estrechat del anillo de mango en 0,5 mm (Figuras 1 y 2 muestran tamaños apropiados). En cuanto a la calidad de la hoja, sólo debe considerarse de acero inoxidable. Aunque ligeramente menos flexible en comparación con la hoja de acero de carbono medio, cuchillas de acero inoxidable no se desarrollan óxido, lo que permite un uso en la vida de las asas. De nota, el diseño de las asas y puños actuales es el resultado de un proceso, que ha llevado a los tamaños de propuestas, lo que permite para las anastomosis más eficientes. Gemelos diámetros varían de acuerdo con los pesos de rata (Tabla 1). Mínimas variaciones se pueden tolerar en términos de longitud, con una longitud habitual de alrededor de 4 mm (Figuras 3 y 4). En cuanto a la aproximador, la pinza de Kocher seleccionado debería haber mangos al menos 4 cm del punto de apoyo. Esto permite un cierre seguro de la rejilla fuera del abdomen del animal. En general,el dispositivo propuesto puede permitir la anastomosis de vena más fácil para el trasplante de hígado y otros tipos de injertos en ratas.

Una técnica de trasplante ortotópico de hígado de rata se ha demostrado en un reciente Diario de experimentos visualizados papel 1. Vena porta y de infra-hepáticos vena cava anastomosis se realizaron con la técnica de puño asistida rápido enlazador. Esta técnica fue elegida entre otras revisiones de la técnica del Kamada original de 2-4, ya que permite la anastomosis más fácil y más rápido, resulta en una mejor hemodinámica, y puede ser implementado con una curva de aprendizaje más corta 1,5. La técnica rápida-enlazador requiere el uso de un mango, un aproximador y puños, todos los cuales pueden ser diseñados a partir de material común de laboratorio de acuerdo con la técnica descrita en el presente informe.

<table border="1">
<tbody>
 <tr>
 <td>Tool / Reagent</td>
 <td>Company</td>
 <td>Catalogue n.</td>
 <td>Comment</td>
 </tr>
 <tr>
 <td>Porta cuff</td>
 <td>altecweb or 
 smiths-medical</td>
 <td>Coil 01-96-1729 
 800/100/420</td>
 <td>Bore : variable 
 Wall : 0.30 mm 
 Length: 3.8-4.2 mm 
 <a href="http://altecweb.com" target="_blank">altecweb.com</a> or 
 <a href="http://smiths-medical.com" target="_blank">smiths-medical.com</a></td>
 </tr>
 <tr>
 <td>IVC cuff</td>
 <td>altecweb or 
 smiths-medical </td>
 <td>Coil 01-96-1733 
 800/100/540</td>
 <td>Bore : variable 
 Wall : 0.30 mm 
 Length: 3.8-4.2 mm 
 <a href="http://altecweb.com" target="_blank">altecweb.com</a> or 
 <a href="http://smiths-medical.com" target="_blank">smiths-medical.com</a></td>
 </tr>
 <tr>
 <td>Mini-drill </td>
 <td>Dremel</td>
 <td>100 series</td>
 <td>35,000 rpm 
 <a href="http://dremel.com" target="_blank">dremel.com</a></td>
 </tr>
 <tr>
 <td>Diamond wheel point</td>
 <td>Dremel</td>
 <td>7103</td>
 <td>2 mm 
 <a href="http://dremel.com" target="_blank">dremel.com</a></td>
 </tr>
 <tr>
 <td>Diamond wheel point</td>
 <td>Dremel</td>
 <td>7105</td>
 <td>4.4 mm 
 <a href="http://dremel.com" target="_blank">dremel.com</a></td>
 </tr>
 <tr>
 <td>Diamond wheel point</td>
 <td>Dremel</td>
 <td>7144</td>
 <td>2.4 mm 
 <a href="http://dremel.com" target="_blank">dremel.com</a></td>
 </tr>
 <tr>
 <td>Cut-off wheels</td>
 <td>Dremel</td>
 <td>420</td>
 <td>dia: 23.8 mm 
 thickness: 0.5 mm 
 <a href="http://dremel.com" target="_blank">dremel.com</a></td>
 </tr>
 <tr>
 <td>Quick-linker handles</td>
 <td>dltchiropody (DLT)</td>
 <td>PAR 10</td>
 <td>modified scalpel blades 
 <a href="http://dltchiropody.co.uk" target="_blank">dltchriopdy</a></td>
 </tr>
 <tr>
 <td>Quick-linker approximator</td>
 <td>pharmap</td>
 <td>UD-04-275</td>
 <td>modified Kocher's forceps 
 <a href="http://pharmap.ch" target="_blank">pharmap.ch</a></td>
 </tr>
 </tbody>
</table>

manufacturing devices and instruments for easier rat liver transplantation

Trasplante ortotópico de hígado de rata es un modelo popular, que se ha demostrado en un papel JoVe reciente con el uso del dispositivo &quot;rápida-enlazador&quot;. Esta técnica permite la fácil venosa del manguito-anatomoses después de una curva de aprendizaje razonable. El dispositivo se compone de dos asas, que se talla fuera de hojas de bisturí, una aproximador, que se obtiene mediante la modificación de unas pinzas de Kocher, y los puños diseñados a partir de tubo de polietileno de calibre fino. Todo el proceso se puede realizar en un laboratorio común el uso de material de bajo costo. El presente informe proporciona un protocolo paso a paso para el diseño de las piezas necesarias e incluye plantillas.

Cinco equipos, entre ellos cinco aproximadores y 11 tiradores han sido fabricados. Un asa se rompió durante la final cepillado. Este problema era debido al hecho de que el anillo de la manija era demasiado estrecha, y se ha resuelto mediante el establecimiento de la parte más estrecha del anillo de mango a 0,5 mm. No hay problemas ocurrieron durante la formación de los aproximadores. <table border="1"><tbody><tr><td> Peso Rat (g) </td><td> Porta mango (diámetro interno) (mm) </td><td> Porta manguito (diámetro exterior) (mm) </td><td> IVC mango (diámetro interno) (mm) </td><td> IVC manguito (diámetro exterior) (mm) </td></tr><tr><td> 120-180 </td><td> 2.2 </td><td> 1.7 </td><td> 2.6 </td><td> 2.08 </td></tr><tr><td> 180-270 </td><td> 2.6 </td><td> 2.08 </td><td> 03.04 a 03.07 </td><td> 3,0-3,25 </td></tr><tr><td> &gt; 270 </td><td> 2.9<html></td><td> 2.42 </td><td> 4.2 </td><td> 3.7 </td></tr></tbody></table> La Tabla 1. <img src="/files/ftp_upload/50380/50380fig1.jpg" alt="Figura 1" fo:content-width="6in" fo:src="/files/ftp_upload/50380/50380fig1highres.jpg"/> Figura 1. Porta plantilla mango. Si impresa con una escala de 1:01 se puede utilizar para guiar el mango de la conformación. <a href="https://www.jove.com/files/ftp_upload/50380/50380fig1large.jpg" target="_blank">Haga clic aquí para ver la figura más grande</a> . <img src="/files/ftp_upload/50380/50380fig2.jpg" alt="La figura 2" fo:content-width="6in" fo:src="/files/ftp_upload/50380/50380fig2highres.jpg"/> Figura 2. IVC plantilla mango. Si impresa con una escala de 1:01 se puede utilizar para guiar el mango de la conformación. <a href="https://www.jove.com/files/ftp_upload/50380/50380fig2large.jpg" target="_blank">Haga clic aquí para ver la figura más grande</a> . contenido &quot;&gt; <img src="/files/ftp_upload/50380/50380fig3.jpg" alt="Figura 3" fo:content-width="4.6in" fo:src="/files/ftp_upload/50380/50380fig3highres.jpg" /> Figura 3. V.Porta Porta y IVC puños vista lateral. Del injerto debe ser asegurado a la ranura central, mientras recipiente del destinatario al lateral. Este recurso permite el contacto óptimo de la íntima-a-íntima. <img src="/files/ftp_upload/50380/50380fig4.jpg" alt="Figura 4" fo:content-width="4.1in" fo:src="/files/ftp_upload/50380/50380fig4highres.jpg"/> La Figura 4. Están representados Porta y IVC puños vista frontal. Calibradores adecuados para ratas que pesaban 180-270 g.

Watch this Scientific Journal Video about Manufacturing Devices and Instruments for Easier Rat Liver Transplantation at JoVE.com

Manufacturing Devices and Instruments for Easier Rat Liver Transplantation

Se describe el diseño del dispositivo &quot;quick-linker&quot; para el trasplante ortotópico de hígado de rata más fácil.

Fabricación de aparatos e instrumentos para facilitar la rata Trasplante de Hígado

Orthotopic rat liver transplantation is a popular model, which has been shown in a recent JoVE paper with the use of the "quick-linker" device. This ...

manufacturing-devices-instruments-for-easier-rat-liver

Research

JoVE Journal

Bioengineering

8.6K vistas.  University of Geneva Hospitals. Se describe el diseño del dispositivo "quick-linker" para el trasplante ortotópico de hígado de rata más fácil.

Video: Manufacturing Devices and Instruments for Easier Rat Liver Transplantation

Mass Cytometry: Protocol for Daily Tuning and Running Cell Samples on a CyTOF Mass Cytometer

In recent years, the rapid analysis of single cells has commonly been performed using flow cytometry and fluorescently-labeled antibodies. However, the issue of spectral overlap of fluorophore emissions has limited the number of simultaneous probes. In contrast, the new CyTOF mass cytometer by DVS Sciences couples a liquid single-cell introduction system to an ICP-MS.1 Rather than fluorophores, chelating polymers containing highly-enriched metal isotopes are coupled to antibodies or other specific probes.2-5 Because of the metal purity and mass resolution of the mass cytometer, there is no "spectral overlap" from neighboring isotopes, and therefore no need for compensation matrices. Additionally, due to the use of lanthanide metals, there is no biological background and therefore no equivalent of autofluorescence. With a mass window spanning atomic mass 103-203, theoretically up to 100 labels could be distinguished simultaneously. Currently, more than 35 channels are available using the chelating reagents available from DVS Sciences, allowing unprecedented dissection of the immunological profile of samples.6-7
Disadvantages to mass cytometry include the strict requirement for a separate metal isotope per probe (no equivalent of forward or side scatter), and the fact that it is a destructive technique (no possibility of sorting recovery). The current configuration of the mass cytometer also has a cell transmission rate of only ~25%, thus requiring a higher input number of cells.
Optimal daily performance of the mass cytometer requires several steps. The basic goal of the optimization is to maximize the measured signal intensity of the desired metal isotopes (M) while minimizing the formation of oxides (M+16) that will decrease the M signal intensity and interfere with any desired signal at M+16. The first step is to warm up the machine so a hot, stable ICP plasma has been established. Second, the settings for current and make-up gas flow rate must be optimized on a daily basis. During sample collection, the maximum cell event rate is limited by detector efficiency and processing speed to 1000 cells/sec. However, depending on the sample quality, a slower cell event rate (300-500 cells/sec) is usually desirable to allow better resolution between cells events and thus maximize intact singlets over doublets and debris. Finally, adequate cleaning of the machine at the end of the day helps minimize background signal due to free metal.

The steps necessary for daily tuning and optimization of the performance of a CyTOF mass cytometer are described. Comments on optimal sample preparation and flow rate are discussed

Citometría de masas: Protocolo para la afinación y servicio diario muestras de células en un citómetro de masas CyTOF

In recent years, the rapid analysis of single cells has commonly been performed using flow cytometry and fluorescently-labeled antibodies. However, the ...

Investigación

Bioingeniería

Paper-based Devices for Isolation and Characterization of Extracellular Vesicles

Extracellular vesicles (EVs), membranous particles released from various types of cells, hold a great potential for clinical applications. They contain nucleic acid and protein cargo and are increasingly recognized as a means of intercellular communication utilized by both eukaryote and prokaryote cells. However, due to their small size, current protocols for isolation of EVs are often time consuming, cumbersome, and require large sample volumes and expensive equipment, such as an ultracentrifuge. To address these limitations, we developed a paper-based immunoaffinity platform for separating subgroups of EVs that is easy, efficient, and requires sample volumes as low as 10 &#956;l. Biological samples can be pipetted directly onto paper test zones that have been chemically modified with capture molecules that have high affinity to specific EV surface markers. We validate the assay by using scanning electron microscopy (SEM), paper-based enzyme-linked immunosorbent assays (P-ELISA), and transcriptome analysis. These paper-based devices will enable the study of EVs in the clinic and the research setting to help advance our understanding of EV functions in health and disease.

This protocol details a method to isolate extracellular vesicles (EVs), small membranous particles released from cells, from as little as 10 &#956;l serum samples. This approach circumvents the need for ultracentrifugation, requires only a few minutes of assay time, and enables the isolation of EVs from samples of limited volumes.

Dispositivos basados ​​en papel para aislamiento y caracterización de extracelular vesículas

Extracellular vesicles (EVs), membranous particles released from various types of cells, hold a great potential for clinical applications. They contain ...

Procedure for Decellularization of Rat Livers in an Oscillating-pressure Perfusion Device

Decellularization and recellularization of parenchymal organs may enable the generation of functional organs in vitro, and several protocols for rodent liver decellularization have already been published. We aimed to improve the decellularization process by construction of a proprietary perfusion device enabling selective perfusion via the portal vein and/or the hepatic artery. Furthermore, we sought to perform perfusion under oscillating surrounding pressure conditions to improve the homogeneity of decellularization. The homogeneity of perfusion decellularization has been an underestimated factor to date. During decellularization, areas within the organ that are poorly perfused may still contain cells, whereas the extracellular matrix (ECM) in well-perfused areas may already be affected by alkaline detergents. Oscillating pressure changes can mimic the intraabdominal pressure changes that occur during respiration to optimize microperfusion inside the liver. In the study presented here, decellularized rat liver matrices were analyzed by histological staining, DNA content analysis and corrosion casting. Perfusion via the hepatic artery showed more homogenous results than portal venous perfusion did. The application of oscillating pressure conditions improved the effectiveness of perfusion decellularization. Livers perfused via the hepatic artery and under oscillating pressure conditions showed the best results. The presented techniques for liver harvesting, cannulation and perfusion using our proprietary device enable sophisticated perfusion set-ups to improve decellularization and recellularization experiments in rat livers.

The presented techniques for liver harvesting, cannulation and perfusion using our proprietary device enable sophisticated perfusion set-ups to improve decellularization and recellularization experiments in rat livers.

Procedimiento para Descelularización de rata hígados en un dispositivo de perfusión oscilante presión

Decellularization and recellularization of parenchymal organs may enable the generation of functional organs in vitro, and several protocols for rodent ...

Fabricating Cotton Analytical Devices

A robust, low-cost analytical device should be user-friendly, rapid, and affordable. Such devices should also be able to operate with scarce samples and provide information for follow-up treatment. Here, we demonstrate the development of a cotton-based urinalysis (i.e., nitrite, total protein, and urobilinogen assays) analytical device that employs a lateral flow-based format, and is inexpensive, easily fabricated, rapid, and can be used to conduct multiple tests without cross-contamination worries. Cotton is composed of cellulose fibers with natural absorptive properties that can be leveraged for flow-based analysis. The simple but elegant fabrication process of our cotton-based analytical device is described in this study. The arrangement of the cotton structure and test pad takes advantage of the hydrophobicity and absorptive strength of each material. Because of these physical characteristics, colorimetric results can persistently adhere to the test pad. This device enables physicians to receive clinical information in a timely manner and shows great potential as a tool for early intervention.

To investigate simple fabrication approaches for multiple assay needs, we created a fluid-absorbing channel system made of cotton material. This device was used to establish a multiple detection platform, and solve contamination issues that commonly affect lateral flow-based biomedical devices, for clinical urinalysis of nitrite, total protein, and urobilinogen.

La fabricación de dispositivos analíticos de algodón

A robust, low-cost analytical device should be user-friendly, rapid, and affordable. Such devices should also be able to operate with scarce samples and ...

A Simple and Scalable Fabrication Method for Organic Electronic Devices on Textiles

Today, wearable electronics devices combine a large variety of functional, stretchable, and flexible technologies. However, in many cases, these devices cannot be worn under everyday conditions. Therefore, textiles are commonly considered the best substrate to accommodate electronic devices in wearable use. In this paper, we describe how to selectively pattern organic electroactive materials on textiles from a solution in an easy and scalable manner. This versatile deposition technique enables the fabrication of wearable organic electronic devices on clothes.

In this paper, we present a protocol to selectively deposit organic materials on textiles, which allows for the direct integration of organic electronic devices with wearables. The fabricated devices can be fully integrated in textiles, respecting their mechanical appearance and enabling sensing capabilities.

Un método de fabricación simple y escalable para dispositivos electrónicos orgánicos sobre los Textiles

Today, wearable electronics devices combine a large variety of functional, stretchable, and flexible technologies. However, in many cases, these devices ...

Optimized Setup and Protocol for Magnetic Domain Imaging with In Situ Hysteresis Measurement

This paper elaborates the sample preparation protocols required to obtain optimal domain patterns using the Bitter method, focusing on the extra steps compared to standard metallographic sample preparation procedures. The paper proposes a novel bespoke rig for dynamic domain imaging with in situ BH (magnetic hysteresis) measurements and elaborates the protocols for the sensor preparation and the use of the rig to ensure accurate BH measurement. The protocols for static and ordinary dynamic domain imaging (without in situ BH measurements) are also presented. The reported method takes advantage of the convenience and high sensitivity of the traditional Bitter method and enables in situ BH measurement without interrupting or interfering with the domain wall movement processes. This facilitates establishing a direct and quantitative link between the domain wall movement processes&#8211;microstructural feature interactions in ferritic steels with their BH loops. This method is anticipated to become a useful tool for the fundamental study of microstructure&#8211;magnetic property relationships in steels and to help interpret the electromagnetic sensor signals for non-destructive evaluation of steel microstructures.

Optimized Setup and Protocol for Magnetic Domain Imaging with In Situ Hysteresis Measurement

This paper elaborates the sample and sensor preparation procedures and the protocols for using the test rig particularly for dynamic domain imaging with in situ BH measurements in order to achieve optimal domain pattern quality and accurate BH measurements.

Configuración optimizada y protocolo para la proyección de imagen de dominio magnético con In Situ la medición histéresis

This paper elaborates the sample preparation protocols required to obtain optimal domain patterns using the Bitter method, focusing on the extra steps ...

A Novel Surgical Technique As a Foundation for In Vivo Partial Liver Engineering in Rat

Organ engineering is a novel strategy to generate liver organ substitutes that can potentially be used in transplantation. Recently, in vivo liver engineering, including in vivo organ decellularization followed by repopulation, has emerged as a promising approach over ex vivo liver engineering. However, postoperative survival was not achieved. The aim of this study is to develop a novel surgical technique of in vivo selective liver lobe perfusion in rats as a prerequisite for in vivo liver engineering. We generate a circuit bypass only through the left lateral lobe. Then, the left lateral lobe is perfused with heparinized saline. The experiment is performed with 4 groups (n = 3 rats per group) based on different perfusion times of 20 min, 2 h, 3 h, and 4 h. Survival, as well as the macroscopically visible change of color and the histologically determined absence of blood cells in the portal triad and the sinusoids, is taken as an indicator for a successful model establishment. After selective perfusion of the left lateral lobe, we observe that the left lateral lobe, indeed, turned from red to faint yellow. In a histological assessment, no blood cells are visible in the branch of the portal vein, the central vein, and the sinusoids. The left lateral lobe turns red after reopening the blocked vessels. 12/12 rats survived the procedure for more than one week. We are the first to report a surgical model for in vivo single liver lobe perfusion with a long survival period of more than one week. In contrast to the previously published report, the most important advantage of the technique presented here is that perfusion of 70% of the liver is maintained throughout the whole procedure. The establishment of this technique provides a foundation for in vivo partial liver engineering in rats, including decellularization and recellularization.

A Novel Surgical Technique As a Foundation for In Vivo Partial Liver Engineering in Rat

We establish a novel surgical technique for an in vivo single liver lobe perfusion model in rat as a prerequisite for further studying in vivo partial liver engineering in the future.

Una novedosa técnica quirúrgica como base para In Vivo parcial ingeniería hígado de rata

Organ engineering is a novel strategy to generate liver organ substitutes that can potentially be used in transplantation. Recently, in vivo liver ...

A Guide to Build a Highly Inclined Swept Tile Microscope for Extended Field-of-view Single-molecule Imaging

Single-molecule imaging has greatly advanced our understanding of molecular mechanisms in biological studies. However, it has been challenging to obtain large field-of-view, high-contrast images in thick cells and tissues. Here, we introduce highly inclined swept tile (HIST) microscopy that overcomes this problem. A pair of cylindrical lenses was implemented to generate an elongated excitation beam that was scanned over a large imaging area via a fast galvo mirror. A 4f configuration was used to position optical components. A scientific complementary metal-oxide semiconductor camera detected the fluorescence signal and blocked the out-of-focus background with a dynamic confocal slit synchronized with the beam sweeping. We present a step-by-step instruction on building the HIST microscope with all basic components.

A detailed instruction is described on how to build a highly inclined swept tile (HIST) microscope and its usage for single-molecule imaging.

Una guía para crear un altamente inclinado barrido microscopio de azulejo para la proyección de imagen de una sola molécula campo de visión extendida

Single-molecule imaging has greatly advanced our understanding of molecular mechanisms in biological studies. However, it has been challenging to obtain ...

Rapid Fabrication of Custom Microfluidic Devices for Research and Educational Applications

Microfluidic devices allow for the manipulation of fluids, particles, cells, micro-sized organs or organisms in channels ranging from the nano to submillimeter scales. A rapid increase in the use of this technology in the biological sciences has prompted a need for methods that are accessible to a wide range of research groups. Current fabrication standards, such as PDMS bonding, require expensive and time consuming lithographic and bonding techniques. A viable alternative is the use of equipment and materials that are easily affordable, require minimal expertise and allow for the rapid iteration of designs. In this work we describe a protocol for designing and producing PET-laminates (PETLs), microfluidic devices that are inexpensive, easy to fabricate, and consume significantly less time to generate than other approaches to microfluidics technology. They consist of thermally bonded film sheets, in which channels and other features are defined using a craft cutter. PETLs solve field-specific technical challenges while dramatically reducing obstacles to adoption. This approach facilitates the accessibility of microfluidics devices in both research and educational settings, providing a reliable platform for new methods of inquiry.

Here we present a protocol to design and fabricate custom microfluidic devices with minimal financial and time investment. The aim is to facilitate the adoption of microfluidic technologies in biomedical research laboratories and educational settings.

Fabricación rápida de dispositivos microfluídicos personalizados para investigación y aplicaciones educativas

Microfluidic devices allow for the manipulation of fluids, particles, cells, micro-sized organs or organisms in channels ranging from the nano to ...

Electric and Magnetic Field Devices for Stimulation of Biological Tissues

Electric fields (EFs) and magnetic fields (MFs) have been widely used by tissue engineering to improve cell dynamics such as proliferation, migration, differentiation, morphology, and molecular synthesis. However, variables such stimuli strength and stimulation times need to be considered when stimulating either cells, tissues or scaffolds. Given that EFs and MFs vary according to cellular response, it remains unclear how to build devices that generate adequate biophysical stimuli to stimulate biological samples. In fact, there is a lack of evidence regarding the calculation and distribution when biophysical stimuli are applied. This protocol is focused on the design and manufacture of devices to generate EFs and MFs and implementation of a computational methodology to predict biophysical stimuli distribution inside and outside of biological samples. The EF device was composed of two parallel stainless-steel electrodes located at the top and bottom of biological cultures. Electrodes were connected to an oscillator to generate voltages (50, 100, 150 and 200 Vp-p) at 60 kHz. The MF device was composed of a coil, which was energized with a transformer to generate a current (1 A) and voltage (6 V) at 60 Hz. A polymethyl methacrylate support was built to locate the biological cultures in the middle of the coil. The computational simulation elucidated the homogeneous distribution of EFs and MFs inside and outside of biological tissues. This computational model is a promising tool that can modify parameters such as voltages, frequencies, tissue morphologies, well plate types, electrodes and coil size to estimate the EFs and MFs to achieve a cellular response.

This protocol describes the step-by-step process to build both electrical and magnetic stimulators used to stimulate biological tissues. The protocol includes a guideline to simulate computationally electric and magnetic fields and manufacture of stimulator devices.

Dispositivos eléctricos y de campo magnético para la estimulación de tejidos biológicos

Electric fields (EFs) and magnetic fields (MFs) have been widely used by tissue engineering to improve cell dynamics such as proliferation, migration, ...