Los autores desean agradecer el apoyo de la Nueva York Capital Region Research Alliance Grant.

1. Bioprinting Plataforma Establecimiento La modificación de la impresora se basa en una impresora de inyección de tinta térmica HP Deskjet 500 y HP 51626A cartucho de tinta de color negro. <ol><li> Retire la tapa de plástico encima de la impresora y cuidadosamente extraiga el panel de control de la cubierta. </li><li> Desconecte las conexiones de los cables entre 3 la parte superior de la impresora y la base. Quite la parte superior de la impresora desde la base. </li><li> En la parte superior de la impresora, retire la pequeña de plástico y accesorios de goma (sistema de limpieza del cabezal de impresión) en el lado derecho debajo del cartucho de tinta. </li><li> Quite la base de la bandeja de papel con resortes. </li><li> Retire la placa metálica que cubre la barra de alimentación de papel de plástico. </li><li> Cortar la barra de alimentación de papel de plástico en la posición de la rueda de alimentación medio usando una sierra de mano u otra herramienta de corte. </li><li> Retire las 2 ruedas de alimentación de papel expuestos después de la etapa anterior. El plástico de la rueda es muy duro y un sistema electrónicosierra será útil. </li><li> Limpie el polvo y los escombros de utilizar paños de aire y etanol en conserva. </li><li> Coloque la parte superior de la impresora a la base. </li><li> UV esterilizar la impresora modificado durante al menos 2 horas en una campana de flujo laminar antes de usar. </li><li> Cortar la tapa de un cartucho de tinta HP 51626A utilizando una sierra de mano u otra herramienta de corte. </li><li> Vaciar la tinta y retire el filtro que cubre el depósito del fondo del pozo del cartílago. </li><li> Enjuague el cartucho a fondo con agua corriente del grifo. </li><li> Ultrasonicate el cartucho en desionizada (DI) durante 10 min para eliminar la tinta residual. </li><li> Examine el cartucho para asegurarse de que toda la tinta se ha eliminado. Enjuague o rociar el cartucho a fondo con etanol al 70% para la esterilización, seguido de agua DI esterilizada. </li><li> Configurar una lámpara de luz ultravioleta de onda larga sobre la plataforma de impresión para proporcionar una capacidad de fotopolimerización simultánea. </li><li> Medir la intensidad de los rayos UV en la plataforma de impresión usando una luz UVmetro. Ajustar la distancia entre la lámpara UV y la plataforma de la impresora de modo que la intensidad de impresión en el sujeto está entre 4-8 mW / cm 2 (aproximadamente 25 cm desde la lámpara a la plataforma de la impresora). </li></ol> 2. Preparación Bioink <ol><li> Expansión de condrocitos monocapa <ol><li> Placa de 5 millones de condrocitos humanos en cada matraz de cultivo de tejido T175 para la expansión de células en Dulbecco Modificado Eagles Medium (DMEM) complementado con 10% de suero de ternera y 1x de penicilina-estreptomicina-glutamina (PSG). Células de cultivo a 37 ° C con aire humidificado contiene 5% de CO 2. Cambiar el medio de cultivo cada 3 días hasta que el matraz es 85% de confluencia. Utilice células de la misma pasaje. </li></ol></li><li> Disolver PEGDA en PBS a una concentración final de 10% w / v Añadir fotoiniciador I-2959 a una concentración final de 0,05% w / v Filtrar esterilizar la solución. </li><li> Suspender los condrocitos humanos cultivados en la solución PEGDA preparado a 5 x 10 6 células /ml. </li></ol> 3. El cartílago de tejido de impresión <ol><li> Encienda la impresora y el ordenador portátil. </li><li> Crear un patrón de impresión de un círculo sólido con 4 mm de diámetro utilizando Microsoft Word o Adobe Photoshop. <ol><li> Ajuste la posición del patrón y asegúrese de que se imprimirá exactamente en el molde de plástico. </li><li> Calcular el número de copias necesarias para alcanzar el espesor deseado del andamio. Para 4 mm de altura, se requieren 220 impresiones para crear el andamio deseado. </li></ol></li><li> Cargue el bioink en el cartucho de tinta. Cubra el cartucho con papel de aluminio para protegerlo de la exposición directa del sol durante la impresión. </li><li> Enviar comando de impresión a la impresora. Tire del sensor de papel cuando la impresora comienza a imprimir. El proceso de impresión de conjunto debería tomar menos de 4 minutos para un andamio con 4 mm de diámetro y 4 mm de altura. </li><li> Transferencia impreso neocartílago a una placa de 24 pocillos y añadir 1,5 ml de medio de cultivo a cada pocillo. </li></ol><ol><li> Incubar la neocartílago impreso en solución VIVO / DEAD viabilidad / citotoxicidad de trabajo a temperatura ambiente durante 15 min en la oscuridad. </li><li> Cortar el hidrogel de células cargadas por la mitad y tomar imágenes fluorescentes de la zona de corte. </li><li> Cuente en vivo las células muertas (rojo) (verde) y por un observador ciego a los cinco imágenes tomadas al azar. Calcular la viabilidad celular mediante la división del número de células vivas por el número total de células vivas y muertas. </li></ol>

<ol>
	<li>Cui, X., Boland, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Human+microvasculature+fabrication+using+thermal+inkjet+printing+technology.">Human microvasculature fabrication using thermal inkjet printing technology.</a> Biomaterials. 30, 6221-6227 (2009).</li><li>Cui, X., Breitenkamp, K., Finn, M. G., Lotz, M., D'Lima, D. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Direct+human+cartilage+repair+using+three-dimensional+bioprinting+technology.">Direct human cartilage repair using three-dimensional bioprinting technology.</a> Tissue Eng Part A. 18, 1304-1312 (2012).</li><li>Cui, X., Breitenkamp, K., Lotz, M., D'Lima, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Synergistic+action+of+fibroblast+growth+factor-2+and+transforming+growth+factor-beta1+enhances+bioprinted+human+neocartilage+formation.">Synergistic action of fibroblast growth factor-2 and transforming growth factor-beta1 enhances bioprinted human neocartilage formation.</a> Biotechnol. Bioeng. 109, 2357-2368 (2012).</li><li>Cui, X., Breitenkamp, K., Finn, M. G., Lotz, M., Colwell, C. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Direct+human+cartilage+repair+using+thermal+inkjet+printing+technology.">Direct human cartilage repair using thermal inkjet printing technology.</a> Osteoarthritis and Cartilage. 19, (2011).</li><li>Cui, X., Boland, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Simultaneous+deposition+of+human+microvascular+endothelial+cells+and+biomaterials+for+human+microvasculature+fabrication+using+inkjet+printing.">Simultaneous deposition of human microvascular endothelial cells and biomaterials for human microvasculature fabrication using inkjet printing.</a> NIP24/digital Fabrication 2008: 24th International Conference on Digital Printing Technologies, Technical Program and Proceedings. 24, 480-483 (2008).</li><li>Cui, X., Dean, D., Ruggeri, Z. M., Boland, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Cell+damage+evaluation+of+thermal+inkjet+printed+Chinese+hamster+ovary+cells.">Cell damage evaluation of thermal inkjet printed Chinese hamster ovary cells.</a> Biotechnol. Bioeng. 106, 963-969 (2010).</li><li>Cui, X., Hasegawa, A., Lotz, M., D'Lima, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Structured+three-dimensional+co-culture+of+mesenchymal+stem+cells+with+meniscus+cells+promotes+meniscal+phenotype+without+hypertrophy.">Structured three-dimensional co-culture of mesenchymal stem cells with meniscus cells promotes meniscal phenotype without hypertrophy.</a> Biotechnol. Bioeng. 109, 2369-2380 (2012).</li><li>Cui, X., Gao, G., Qiu, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Accelerated+myotube+formation+using+bioprinting+technology+for+biosensor+applications.">Accelerated myotube formation using bioprinting technology for biosensor applications.</a> Biotechnol. Lett. 35, 315-321 (2013).</li><li>Cui, X., Boland, T., D'Lima, D. D., Lotz, M. K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Thermal+inkjet+printing+in+tissue+engineering+and+regenerative+medicine.">Thermal inkjet printing in tissue engineering and regenerative medicine.</a> Recent Pat Drug Deliv Formul. 6, 149-155 (2012).</li><li>Bryant, S. J., Anseth, K. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Hydrogel+properties+influence+ECM+production+by+chondrocytes+photoencapsulated+in+poly(ethylene+glycol)+hydrogels.">Hydrogel properties influence ECM production by chondrocytes photoencapsulated in poly(ethylene glycol) hydrogels.</a> Journal of Biomedical Materials Research. 59, 63-72 (2002).</li><li>Elisseeff, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Photoencapsulation+of+chondrocytes+in+poly(ethylene+oxide)-based+semi-interpenetrating+networks.">Photoencapsulation of chondrocytes in poly(ethylene oxide)-based semi-interpenetrating networks.</a> Journal of Biomedical Materials Research. 51, 164-171 (2000).</li><li>Buskirk, W. A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Development+of+A+High-Resolution+Thermal+Inkjet+Printhead.">Development of A High-Resolution Thermal Inkjet Printhead.</a> Hewlett-Packard Journal. 39, 55-61 (1988).</li><li>Harmon, J. P., Widder, J. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Integrating+the+Printhead+Into+the+HP+Deskjet+Printer.">Integrating the Printhead Into the HP Deskjet Printer.</a> Hewlett-Packard Journal. 39, 62-66 (1988).</li><li>Kim, T. K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Experimental+model+for+cartilage+tissue+engineering+to+regenerate+the+zonal+organization+of+articular+cartilage.">Experimental model for cartilage tissue engineering to regenerate the zonal organization of articular cartilage.</a> Osteoarthritis and Cartilage. 11, 653-664 (2003).</li><li>Sharma, B., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Designing+zonal+organization+into+tissue-engineered+cartilage.">Designing zonal organization into tissue-engineered cartilage.</a> Tissue Engineering. 13, 405-414 (2007).</li><li>Cohen, D. L., Lipton, J. I., Bonassar, L. J., Lipson, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Additive+manufacturing+for+in+situ+repair+of+osteochondral+defects.">Additive manufacturing for in situ repair of osteochondral defects.</a> Biofabrication. 2, (2010).</li></ol>

Los autores no tienen ningún interés financiero en este estudio.

Este sistema bioprinting 3D con capacidad de fotopolimerización simultánea proporciona una significativamente mayor resolución de impresión que el mejor método descrito de esta en la impresión in situ de los defectos osteocondrales utilizando jeringa extruido un hidrogel de alginato celular 16. Una mayor resolución de impresión es particularmente crítico para la ingeniería de tejidos de cartílago para restaurar la organización zonal cartílago anatómica. Fotopolimerización simu...

Bioprinting basa en la impresión de inyección de tinta térmica es una de las tecnologías que permiten más prometedores en el campo de la ingeniería de tejidos y medicina regenerativa. Con cabezales de impresión de control digital y de alto rendimiento factores de células, andamios, y crecimiento pueden ser depositados precisamente a la de dos dimensiones (2D) deseado y posiciones (3D) tridimensionales rápidamente. Muchas aplicaciones exitosas se han cumplido con esta tecnología en ingeniería de tejidos y medicina regenerativa 1-9. En este trabajo, una plataforma bioprinting se estableció con una impresora Deskjet modificado Hewlett-Packard (HP) 500 térmica de inyección de tinta y un sistema de fotopolimerización simultánea. Hidrogeles sintéticos formulados a partir de poli (etilenglicol) (PEG) han mostrado la capacidad de mantener la viabilidad de los condrocitos y promover la producción de ECM condrogénica 10,11. Además, fotorreticulable PEG es altamente soluble en agua con baja viscosidad, lo que lo hace ideal para polyme simultánearización durante bioprinting 3D. En este trabajo, los condrocitos humanos en suspensión en el poli (etileno) diacrilato (PEGDA; MW 3400) se imprimieron precisamente para construir capa-por-capa neocartílago con 1400 dpi de resolución en 3D. Se observó la distribución homogénea de células depositadas en un andamio 3D, que generó tejido de cartílago con excelentes propiedades mecánicas y la mejora de la producción de ECM. Por el contrario, en la fabricación manual de las células acumuladas en la parte inferior del gel en lugar de sus posiciones depositados inicialmente debido a la polimerización de andamio más lenta, lo que condujo a la formación de cartílago no homogénea después de la cultura 2,3.

<table border="0" cellpadding="0" cellspacing="0">
	<tbody>
		<tr height="22">
			<td height="22" style="height:22px;width:357px;">HP Deskjet 500 thermal inkjet printer</td>
			<td style="width:221px;">Hewlett-Packard</td>
			<td style="width:195px;">C2106a</td>
			<td style="width:433px;">Discontinued. Purchased refurbished from internet vendor.</td>
		</tr>
		<tr height="22">
			<td height="22" style="height:22px;width:357px;">HP black ink cartridge</td>
			<td style="width:221px;">Hewlett-Packard</td>
			<td style="width:195px;">51626a</td>
			<td style="width:433px;"></td>
		</tr>
		<tr height="22">
			<td height="22" style="height:22px;width:357px;">Ultraviolet lamp</td>
			<td style="width:221px;">UVP</td>
			<td style="width:195px;">B-100AP</td>
			<td style="width:433px;"></td>
		</tr>
		<tr height="22">
			<td height="22" style="height:22px;width:357px;">UV light meter</td>
			<td style="width:221px;">General Tools</td>
			<td style="width:195px;">UV513AB</td>
			<td style="width:433px;"></td>
		</tr>
		<tr height="22">
			<td height="22" style="height:22px;width:357px;">Zeiss LSM 510 laser scanning microscope</td>
			<td style="width:221px;">Carl Zeiss</td>
			<td style="width:195px;">LSM 510</td>
			<td style="width:433px;"></td>
		</tr>
		<tr height="22">
			<td height="22" style="height:22px;width:357px;">Dulbeccos Modified Eagles Medium (DMEM)</td>
			<td style="width:221px;">Mediatech</td>
			<td style="width:195px;">10-013</td>
			<td style="width:433px;"></td>
		</tr>
		<tr height="22">
			<td height="22" style="height:22px;width:357px;">Penicillin-streptomycin-glutamine (PSG)</td>
			<td style="width:221px;">Invitrogen</td>
			<td style="width:195px;">10378-016</td>
			<td style="width:433px;"></td>
		</tr>
		<tr height="22">
			<td height="22" style="height:22px;width:357px;">Accutase cell dissociation reagent</td>
			<td style="width:221px;">Invitrogen</td>
			<td style="width:195px;">A11105-01</td>
			<td style="width:433px;"></td>
		</tr>
		<tr height="22">
			<td height="22" style="height:22px;width:357px;">Phosphate buffered saline (PBS)</td>
			<td style="width:221px;">Invitrogen</td>
			<td style="width:195px;">10010-023</td>
			<td style="width:433px;"></td>
		</tr>
		<tr height="22">
			<td height="22" style="height:22px;width:357px;">Live/Dead viability/cytotoxicity Kit</td>
			<td style="width:221px;">Invitrogen</td>
			<td style="width:195px;">L-3224</td>
			<td style="width:433px;"></td>
		</tr>
		<tr height="22">
			<td height="22" style="height:22px;width:357px;">Poly(ethylene glycol) diacrylate (PEGDA)</td>
			<td style="width:221px;">Glycosan Biosystems</td>
			<td style="width:195px;">GS700</td>
			<td style="width:433px;"></td>
		</tr>
		<tr height="22">
			<td height="22" style="height:22px;width:357px;">Irgacure 2959</td>
			<td style="width:221px;">Ciba Specialty Chemicals</td>
			<td style="width:195px;">I-2959</td>
			<td style="width:433px;"></td>
		</tr>
		<tr height="22">
			<td height="22" style="height:22px;width:357px;">Human articular chondrocytes</td>
			<td style="width:221px;">Lonza</td>
			<td style="width:195px;">CC-2550</td>
			<td style="width:433px;"></td>
		</tr>
	</tbody>
</table>

human cartilage tissue fabrication using three-dimensional inkjet printing technology

Bioprinting, que se basa en la impresión de inyección de tinta térmica, es una de las más atractivas tecnologías facilitadoras en el campo de la ingeniería de tejidos y medicina regenerativa. Con las células de control digital, andamios, y factores de crecimiento pueden ser depositados precisamente a la de dos dimensiones (2D) deseado y ubicaciones (3D) tridimensionales rápidamente. Por lo tanto, esta tecnología es un enfoque ideal para la fabricación de tejidos que imitan sus estructuras anatómicas nativas. Con el fin de diseñar el cartílago con la organización nativa zonal, composición de la matriz extracelular (ECM), y las propiedades mecánicas, hemos desarrollado una plataforma bioprinting usando una impresora de inyección de tinta comercial con fotopolimerización simultánea capaz para la ingeniería de tejido cartilaginoso 3D. Condrocitos humanos en suspensión en poli (etilenglicol) diacrilato (PEGDA) se imprimieron para la construcción neocartílago 3D mediante el conjunto de capa por capa. Las células fueron fijadas impresos en sus posiciones originales depositados, apoyado por el entorUnding andamio en la fotopolimerización simultánea. Las propiedades mecánicas del tejido impreso fueron similares al cartílago nativo. En comparación con la fabricación de tejidos convencional, que requiere la exposición a UV más larga, la viabilidad de las células impresos con fotopolimerización simultánea fue significativamente mayor. Neocartílago Impreso demostró una excelente glicosaminoglicano (GAG) y la producción de colágeno de tipo II, que era consistente con la expresión de genes. Por lo tanto, esta plataforma es ideal para la distribución de células exacta y la disposición para la ingeniería de tejidos anatómica.

La impresora de inyección de tinta térmica modificado era capaz de celular y la deposición de andamio con un alto rendimiento y una excelente viabilidad celular. La combinación con la fotopolimerización simultánea y biomateriales fotosensibles, esta tecnología es capaz de fijar las células y otras sustancias impresos a los lugares depositados inicialmente. De acuerdo con las propiedades de la impresora de inyección de tinta térmica modificada, la resolución de impresión de 300 dpi 2D con un solo volumen de g...

Watch this Scientific Journal Video about Human Cartilage Tissue Fabrication Using Three-dimensional Inkjet Printing Technology at JoVE.com

Human Cartilage Tissue Fabrication Using Three-dimensional Inkjet Printing Technology

Los métodos descritos en este artículo muestran cómo convertir una impresora de inyección de tinta comercial en un bioprinter con la polimerización UV simultánea. La impresora es capaz de construir la estructura del tejido 3D con células y biomateriales. El estudio ha demostrado aquí construyó un neocartílago 3D.

El cartílago humano Tissue Fabrication Usando tridimensional Tecnología de impresión inyección de tinta

Bioprinting, which is based on thermal inkjet printing, is one of the most attractive enabling technologies in the field of tissue engineering and ...

human-cartilage-tissue-fabrication-using-three-dimensional-inkjet

Research

JoVE Journal

Bioengineering

15.6K vistas.  Rensselaer Polytechnic Institute.  Los métodos descritos en este artículo muestran cómo convertir una impresora de inyección de tinta comercial en un bioprinter con la polimerización UV simultánea. La impresora es capaz de construir la estructura del tejido 3D con células y biomateriales. El estudio ha demostrado aquí construyó un neocartílago 3D. 

Video: Human Cartilage Tissue Fabrication Using Three-dimensional Inkjet Printing Technology

Planar and Three-Dimensional Printing of Conductive Inks

Printed electronics rely on low-cost, large-area fabrication routes to create flexible or multidimensional electronic, optoelectronic, and biomedical devices1-3. In this paper, we focus on one- (1D), two- (2D), and three-dimensional (3D) printing of conductive metallic inks in the form of flexible, stretchable, and spanning microelectrodes.
Direct-write assembly4,5 is a 1-to-3D printing technique that enables the fabrication of features ranging from simple lines to complex structures by the deposition of concentrated inks through fine nozzles (~0.1 - 250 &mu;m). This printing method consists of a computer-controlled 3-axis translation stage, an ink reservoir and nozzle, and 10x telescopic lens for visualization. Unlike inkjet printing, a droplet-based process, direct-write assembly involves the extrusion of ink filaments either in- or out-of-plane. The printed filaments typically conform to the nozzle size. Hence, microscale features (&lt; 1 &mu;m) can be patterned and assembled into larger arrays and multidimensional architectures.
In this paper, we first synthesize a highly concentrated silver nanoparticle ink for planar and 3D printing via direct-write assembly. Next, a standard protocol for printing microelectrodes in multidimensional motifs is demonstrated. Finally, applications of printed microelectrodes for electrically small antennas, solar cells, and light-emitting diodes are highlighted.

Planar and three-dimensional printing of conductive metallic inks is described. Our approach provides new avenues for fabricating printed electronic, optoelectronic, and biomedical devices in unusual layouts at the microscale.

Impresión plana y tridimensional de tintas conductoras

Printed electronics rely on low-cost, large-area fabrication routes to create flexible or multidimensional electronic, optoelectronic, and biomedical ...

Investigación

Bioingeniería

Generation of a Three-dimensional Full Thickness Skin Equivalent and Automated Wounding

In vitro models are a cost effective and ethical alternative to study cutaneous wound healing processes. Moreover, by using human cells, these models reflect the human wound situation better than animal models. Although two-dimensional models are widely used to investigate processes such as cellular migration and proliferation, models that are more complex are required to gain a deeper knowledge about wound healing. Besides a suitable model system, the generation of precise and reproducible wounds is crucial to ensure comparable results between different test runs. In this study, the generation of a three-dimensional full thickness skin equivalent to study wound healing is shown. The dermal part of the models is comprised of human dermal fibroblast embedded in a rat-tail collagen type I hydrogel. Following the inoculation with human epidermal keratinocytes and consequent culture at the air-liquid interface, a multilayered epidermis is formed on top of the models. To study the wound healing process, we additionally developed an automated wounding device, which generates standardized wounds in a sterile atmosphere.

The goal of this protocol is to build up a three-dimensional full thickness skin equivalent, which resembles natural skin. With a specifically constructed automated wounding device, precise and reproducible wounds can be generated under maintenance of sterility.

Generación de una tridimensional grosor de la piel completa y automatizada Equivalente Heridas

In vitro models are a cost effective and ethical alternative to study cutaneous wound healing processes. Moreover, by using human cells, these models ...

Three-dimensional Biomimetic Technology: Novel Biorubber Creates Defined Micro- and Macro-scale Architectures in Collagen Hydrogels

Tissue scaffolds play a crucial role in the tissue regeneration process. The ideal scaffold must fulfill several requirements such as having proper composition, targeted modulus, and well-defined architectural features. Biomaterials that recapitulate the intrinsic architecture of in vivo tissue are vital for studying diseases as well as to facilitate the regeneration of lost and malformed soft tissue. A novel biofabrication technique was developed which combines state of the art imaging, three-dimensional (3D) printing, and selective enzymatic activity to create a new generation of biomaterials for research and clinical application. The developed material, Bovine Serum Albumin rubber, is reaction injected into a mold that upholds specific geometrical features. This sacrificial material allows the adequate transfer of architectural features to a natural scaffold material. The prototype consists of a 3D collagen scaffold with 4 and 3 mm channels that represent a branched architecture. This paper emphasizes the use of this biofabrication technique for the generation of natural constructs. This protocol utilizes a computer-aided software (CAD) to manufacture a solid mold which will be reaction injected with BSA rubber followed by the enzymatic digestion of the rubber, leaving its architectural features within the scaffold material.

An innovative biofabrication technique was developed to engineer three-dimensional constructs that resemble the architectural features, components, and mechanical properties of in vivo tissue. This technique features a newly developed sacrificial material, BSA rubber, which transfers detailed spatial features, reproducing the in vivo architectures of a wide variety of tissues.

Tridimensional Tecnología Biomimética: Novel biorubber Crea Definido micro y macro escala Arquitecturas de colágeno hidrogeles

Tissue scaffolds play a crucial role in the tissue regeneration process. The ideal scaffold must fulfill several requirements such as having proper ...

Fabrication of Inverted Colloidal Crystal Poly(ethylene glycol) Scaffold: A Three-dimensional Cell Culture Platform for Liver Tissue Engineering

The ability to maintain hepatocyte function in vitro, for the purpose of testing xenobiotics&#39; cytotoxicity, studying virus infection and developing drugs targeted at the liver, requires a platform in which cells receive proper biochemical and mechanical cues. Recent liver tissue engineering systems have employed three-dimensional (3D) scaffolds composed of synthetic or natural hydrogels, given their high water retention and their ability to provide the mechanical stimuli needed by the cells. There has been growing interest in the inverted colloidal crystal (ICC) scaffold, a recent development, which allows high spatial organization, homotypic and heterotypic cell interaction, as well as cell-extracellular matrix (ECM) interaction. Herein, we describe a protocol to fabricate the ICC scaffold using poly (ethylene glycol) diacrylate (PEGDA) and the particle leaching method. Briefly, a lattice is made from microsphere particles, after which a pre-polymer solution is added, properly polymerized, and the particles are then removed, or leached, using an organic solvent (e.g., tetrahydrofuran). The dissolution of the lattice results in a highly porous scaffold with controlled pore sizes and interconnectivities that allow media to reach cells more easily. This unique structure allows high surface area for the cells to adhere to as well as easy communication between pores, and the ability to coat the PEGDA ICC scaffold with proteins also shows a marked effect on cell performance. We analyze the morphology of the scaffold as well as the hepatocarcinoma cell (Huh-7.5) behavior in terms of viability and function to explore the effect of ICC structure and ECM coatings. Overall, this paper provides a detailed protocol of an emerging scaffold that has wide applications in tissue engineering, especially liver tissue engineering.

Fabrication of Inverted Colloidal Crystal Polyethylene glycol Scaffold: A Three-dimensional Cell Culture Platform for Liver Tissue Engineering

This manuscript presents a detailed protocol for the fabrication of an emerging three-dimensional hepatocyte culture platform, the inverted colloidal crystal scaffold, and the concomitant techniques to assess hepatocyte behavior. The size-controllable pores, interconnectivity and ability to conjugate extracellular matrix proteins to the poly(ethylene glycol) (PEG) scaffold enhance Huh-7.5 cell performance.

La fabricación de cristal invertida coloidal poli (etilenglicol) Andamios: Una célula Plataforma de cultivo tridimensional para ingeniería de tejidos de hígado

The ability to maintain hepatocyte function in vitro, for the purpose of testing xenobiotics&#39; cytotoxicity, studying virus infection and developing ...

Fabrication of Three-dimensional Paper-based Microfluidic Devices for Immunoassays

Paper wicks fluids autonomously due to capillary action. By patterning paper with hydrophobic barriers, the transport of fluids can be controlled and directed within a layer of paper. Moreover, stacking multiple layers of patterned paper creates sophisticated three-dimensional microfluidic networks that can support the development of analytical and bioanalytical assays. Paper-based microfluidic devices are inexpensive, portable, easy to use, and require no external equipment to operate. As a result, they hold great promise as a platform for point-of-care diagnostics. In order to properly evaluate the utility and analytical performance of paper-based devices, suitable methods must be developed to ensure their manufacture is reproducible and at a scale that is appropriate for laboratory settings. In this manuscript, a method to fabricate a general device architecture that can be used for paper-based immunoassays is described. We use a form of additive manufacturing (multi-layer lamination) to prepare devices that comprise multiple layers of patterned paper and patterned adhesive. In addition to demonstrating the proper use of these three-dimensional paper-based microfluidic devices with an immunoassay for human chorionic gonadotropin (hCG), errors in the manufacturing process that may result in device failures are discussed. We expect this approach to manufacturing paper-based devices will find broad utility in the development of analytical applications designed specifically for limited-resource settings.

We detail a method to fabricate three-dimensional paper-based microfluidic devices for use in the development of immunoassays. Our approach to device assembly is a type of multilayer, additive manufacturing. We demonstrate a sandwich immunoassay to provide representative results for these types of paper-based devices.

La fabricación de dispositivos de microfluidos basados ​​en papel tridimensional para inmunoensayos

Paper wicks fluids autonomously due to capillary action. By patterning paper with hydrophobic barriers, the transport of fluids can be controlled and ...

Melt Electrospinning Writing of Three-dimensional Poly(&#949;-caprolactone) Scaffolds with Controllable Morphologies for Tissue Engineering Applications

This tutorial reflects on the fundamental principles and guidelines for electrospinning writing with polymer melts, an additive manufacturing technology with great potential for biomedical applications. The technique facilitates the direct deposition of biocompatible polymer fibers to fabricate well-ordered scaffolds in the sub-micron to micro scale range. The establishment of a stable, viscoelastic, polymer jet between a spinneret and a collector is achieved using an applied voltage and can be direct-written. A significant benefit of a typical porous scaffold is a high surface-to-volume ratio which provides increased effective adhesion sites for cell attachment and growth. Controlling the printing process by fine-tuning the system parameters enables high reproducibility in the quality of the printed scaffolds. It also provides a flexible manufacturing platform for users to tailor the morphological structures of the scaffolds to their specific requirements. For this purpose, we present a protocol to obtain different fiber diameters using melt electrospinning writing (MEW) with a guided amendment of the parameters, including flow rate, voltage and collection speed. Furthermore, we demonstrate how to optimize the jet, discuss often experienced technical challenges, explain troubleshooting techniques and showcase a wide range of printable scaffold architectures.

Melt Electrospinning Writing of Three-dimensional Poly(&amp;#949;-caprolactone) Scaffolds with Controllable Morphologies for Tissue Engineering Applications

This protocol serves as a comprehensive guideline to fabricate scaffolds via electrospinning with polymer melts in a direct writing mode. We systematically outline the process and define the appropriate parameter settings for achieving targeted scaffold architectures.

Escritura de Electrospinning de andamios Poly(ε-caprolactone) tridimensional con morfologías controlables para aplicaciones de ingeniería de tejidos del derretimiento

This tutorial reflects on the fundamental principles and guidelines for electrospinning writing with polymer melts, an additive manufacturing technology ...

Culturing Mammalian Cells in Three-dimensional Peptide Scaffolds

A useful technique for culturing cells in a self-assembling nanofiber three-dimensional (3D) scaffold is described. This culture system recreates an environment that closely mimics the structural features of non-polarized tissue. Furthermore, the particular intrinsic nanofiber structure of the scaffold makes it transparent to visual light, which allows for easy visualization of the sample under microscopy. This advantage was largely used to study cell migration, organization, proliferation, and differentiation and thus any development of their particular cellular function by staining with specific dyes or probes. Furthermore, in this work, we describe the good performance of this system to easily study the redifferentiation of expanded human articular chondrocytes into cartilaginous tissue. Cells were encapsulated into self-assembling peptide scaffolds and cultured under specific conditions to promote chondrogenesis. Three-dimensional cultures showed good viability during the 4 weeks of the experiment. As expected, samples cultured with chondrogenic inducers (compared to non-induced controls) stained strongly positive for toluidine blue (which stains glycosaminoglycans (GAGs) that are highly present in cartilage extracellular matrix) and expressed specific molecular markers, including collagen type I, II and X, according to Western Blot analysis. This protocol is easy to perform and can be used at research laboratories, industries and for educational purposes in laboratory courses.

Here, we present a protocol to obtain 3D-culture systems in self-assembling peptide scaffolds to promote the differentiation of dedifferentiated human articular chondrocytes into cartilage-like tissue.

Cultivo de células de mamífero en andamios tridimensionales péptido

A useful technique for culturing cells in a self-assembling nanofiber three-dimensional (3D) scaffold is described. This culture system recreates an ...

Three-dimensional Printing of Thermoplastic Materials to Create Automated Syringe Pumps with Feedback Control for Microfluidic Applications

Microfluidics has become a critical tool in research across the biological, chemical, and physical sciences. One important component of microfluidic experimentation is a stable fluid handling system capable of accurately providing an inlet flow rate or inlet pressure. Here, we have developed a syringe pump system capable of controlling and regulating the inlet fluid pressure delivered to a microfluidic device. This system was designed using low-cost materials and additive manufacturing principles, leveraging three-dimensional (3D) printing of thermoplastic materials and off-the-shelf components whenever possible. This system is composed of three main components: a syringe pump, a pressure transducer, and a programmable microcontroller. Within this paper, we detail a set of protocols for fabricating, assembling, and programming this syringe pump system. Furthermore, we have included representative results that demonstrate high-fidelity, feedback control of inlet pressure using this system. We expect this protocol will allow researchers to fabricate low-cost syringe pump systems, lowering the entry barrier for the use of microfluidics in biomedical, chemical, and materials research.

Here we present a protocol to construct a pressure-controlled syringe pump to be used in microfluidic applications. This syringe pump is made from an&#160;additively manufactured body, off-the-shelf hardware, and open-source electronics. The resulting system is low-cost, straightforward to build, and delivers well-regulated fluid flow to enable rapid microfluidic research.

Tridimensional de la impresión de materiales termoplásticos para crear automatizado de bombas de la jeringuilla con retroalimentación de Control para aplicaciones de microfluídica

Microfluidics has become a critical tool in research across the biological, chemical, and physical sciences. One important component of microfluidic ...

Fabrication of Decellularized Cartilage-derived Matrix Scaffolds

Osteochondral defects lack sufficient intrinsic repair capacity to regenerate functionally sound bone and cartilage tissue. To this extent, cartilage research has focused on the development of regenerative scaffolds. This article describes the development of scaffolds that are completely derived from natural cartilage extracellular matrix, coming from an equine donor. Potential applications of the scaffolds include producing allografts for cartilage repair, serving as a scaffold for osteochondral tissue engineering, and providing in vitro models to study tissue formation. By decellularizing the tissue, the donor cells are removed, but many of the natural bioactive cues are thought to be retained. The main advantage of using such a natural scaffold in comparison to a synthetically produced scaffold is that no further functionalization of polymers is required to drive osteochondral tissue regeneration. The cartilage-derived matrix scaffolds can be used for bone and cartilage tissue regeneration in both in vivo and in vitro settings.

Decellularized cartilage-derived scaffolds can be used as a scaffold to guide cartilage repair and as a means to regenerate osteochondral tissue. This paper describes the decellularization process in detail and provides suggestions to use these scaffolds in in vitro settings.

Fabricación de andamios de Decellularized derivados de cartílago matriz

Osteochondral defects lack sufficient intrinsic repair capacity to regenerate functionally sound bone and cartilage tissue. To this extent, cartilage ...

Pancreatic Tissue-Derived Extracellular Matrix Bioink for Printing 3D Cell-Laden Pancreatic Tissue Constructs

The transplantation of pancreatic islets is a promising treatment for patients who suffer from type 1 diabetes accompanied by hypoglycemia and secondary complications. However, islet transplantation still has several limitations such as the low viability of transplanted islets due to poor islet engraftment and hostile environments. In addition, the insulin-producing cells differentiated from human pluripotent stem cells have limited ability to secrete sufficient hormones that can regulate the blood glucose level; therefore, improving the maturation by culturing cells with proper microenvironmental cues is strongly required. In this article, we elucidate protocols for preparing a pancreatic tissue-derived decellularized extracellular matrix (pdECM) bioink to provide a beneficial microenvironment that can increase glucose sensitivity of pancreatic islets, followed by describing the processes for generating 3D pancreatic tissue constructs using a microextrusion-based bioprinting technique.

Decellularized extracellular matrix (dECM) can provide suitable microenvironmental cues to recapitulate the inherent functions of target tissues in an engineered construct. This article elucidates the protocols for the decellularization of pancreatic tissue, evaluation of pancreatic tissue-derived dECM bioink, and generation of 3D pancreatic tissue constructs using a bioprinting technique.

Bioink de matriz extracelular derivada del tejido pancreático para imprimir construcciones de tejido pancreático laden de células 3D

The transplantation of pancreatic islets is a promising treatment for patients who suffer from type 1 diabetes accompanied by hypoglycemia and secondary ...