chemical-synthesis-porous-barium-titanate-thin-film-thermal

Chemical Synthesis of Porous Barium Titanate Thin Film and Thermal Stabilization of Ferroelectric Phase by Porosity-Induced Strain

Barium titanate (BaTiO3, hereafter BT) is an established ferroelectric material first discovered in the 1940s and still widely used because of its ...

National Institute for Materials Science (NIMS)

Size-induced suppression of permittivity in perovskite thin films is a fundamental problem that has remained unresolved for decades. This size-effect issue becomes increasingly important due to the integration of perovskite nanofilms into high-κ capacitors, as well as concerns that intrinsic size effects may limit their device performance. Here, we report a new approach to produce robust high-κ nanodielectrics using perovskite nanosheet (Ca2Nb3O10), a new class of nanomaterials that is derived from layered compounds by exfoliation. By a solution-based bottom-up approach using perovskite nanosheets, we have successfully fabricated multilayer nanofilms directly on SrRuO3 or Pt substrates without any interfacial dead layers. These nanofilms exhibit high dielectric constant (>200), the largest value seen so far in perovskite films with a thickness down to 10 nm. Furthermore, the superior high-κ properties are a size-effect-free characteristic with low leakage current density (<10(-7) A cm(-2)). Our work provides a key for understanding the size effect and also represents a step toward a bottom-up paradigm for future high-κ devices.

Robust high-κ response in molecularly thin perovskite nanosheets.

We have investigated the interface electronic states in self-assembled (Ti(0.8)Co(0.2)O(2)/Ti(0.6)Fe(0.4)O(2))(n) superlattices by X-ray photoelectron spectroscopy. A charge of about -0.3 electron is transferred from Fe to Co ions across the interface and induces a major reconstruction of the orbital occupation at the interfacial (Ti(0.8)Co(0.2)O(2)/Ti(0.6)Fe(0.4)O(2)) layers. Supported by first-principles calculations, the Co(3+) state is partially occupied at the interface by superlattice formation, and this new magnetic state directly influences the coupling between Ti(0.8)Co(0.2)O(2) and Ti(0.6)Fe(0.4)O(2) nanosheets. These data indicate that the orbital reconstruction is indeed realized by the interface charge transfer between Co and Fe ions in the adjoined nanosheets, and the generic feature of engineered interfaces can be extended to self-assembled superlattices of oxide nanosheets.

Orbital reconstruction and interface ferromagnetism in self-assembled nanosheet superlattices.

Two-dimensional (2D) nanosheets, which possess atomic or molecular thickness and infinite planar lengths, are regarded as the thinnest functional nanomaterials. The recent development of methods for manipulating graphene (carbon nanosheet) has provided new possibilities and applications for 2D systems; many amazing functionalities such as high electron mobility and quantum Hall effects have been discovered. However, graphene is a conductor, and electronic technology also requires insulators, which are essential for many devices such as memories, capacitors, and gate dielectrics. Along with graphene, inorganic nanosheets have thus increasingly attracted fundamental research interest because they have the potential to be used as dielectric alternatives in next-generation nanoelectronics. Here, we review the progress made in the properties of dielectric nanosheets, highlighting emerging functionalities in electronic applications. We also present a perspective on the advantages offered by this class of materials for future nanoelectronics.

Two-dimensional dielectric nanosheets: novel nanoelectronics from nanocrystal building blocks.

Ti₁-x-yFexCoyO₂ nanosheets are synthesized in which the (Fe/Co) content is systematically controlled in the range of 0 ≤ x ≤ 0.4 and 0 ≤ y ≤ 0.2. A key feature of this new preparation is the use of (Li/Fe)-, (Fe/Co)- and (Li/Co)-co-substituted layered titanates as starting materials. In exfoliated nanosheets, the composition can be intentionally modified by controlled Fe/Co substitution into Ti sites during the solid-state synthesis of the starting layered compounds. The composition of the host layers is maintained in the subsequent exfoliation process, which is very helpful in the rational design of nanosheets through the use of controlled doping. Through this controlled doping, we achieve exquisite control of the electronic properties of Ti₁-δO₂ nanosheets, including the position of impurity bands, the Fermi energy and ferromagnetic properties. From photoelectron spectroscopy and first-principles studies, we have observed that the use of Fe/Co co-doping with higher Fe and Co oxidation states is necessary to bring the highest occupied Fe/Co impurity states to the Fermi level. This band engineering transforms the Ti₁-x-yFexCoyO₂ nanosheet into a room-temperature half-metallic ferromagnet, thus accomplishing the main requirements of future spinelectronics.

Controlled doping of semiconducting titania nanosheets for tailored spinelectronic materials.

Assemble metal nanoparticles into various ordered structures with scale up to centimeter area is required to meet diverse needs of lab-on-a-chips and analytic components. Here, we present the uniform and high-yield fabrication of centimeter-scale gold nanoparticles (AuNPs) array for SERS substrates. Ferroelectric-assisted assembly of AuNPs line array is successfully fabricated by using a periodically poled LiNbO(PPLN) single crystal as a template. SNOM-Raman shows that the uniform assembly of AuNPs exhibits a high density of "hot spots" arising from strong electromagnetic (EM) field coupling induced by adjacent AuNPs. Quantitative analysis based on SERS detection describes an excellent reproducibility with an intensity variation less than 7% at 1649 cmof Rhodamine 6G. SERS spectra combined with 3D-FDTD modelling indicate that the EM enhancement occurs at all three excitation wavelength of 515, 561 and 633 nm and the 561-nm-laser displays the strongest Raman enhancement with an enhancement factor in an order of 10. The corresponding experimental and theoretical results present a new strategy to fabricate large-area, highly reproducible and sensitive SERS substrates for practical applications.

Ferroelectric-assisted gold nanoparticles array for centimeter-scale highly reproducible SERS substrates.

We present an overview of recent investigations on the dielectric/ferroelectric properties of Dion-Jacobson-type perovskites, including bulk 3D layered systems and their exfoliated 2D nanosheets. In contrast to the Ruddlesden-Popper and Aurivillius phases, the Dion-Jacobson phases in bulk 3D systems have not been important targets for constructing dielectric/ferroelectric materials. However, recent investigations on Dion-Jacobson phases have provided new impetus to dielectric/ferroelectric materials. Dion-Jacobson perovskites can also facilitate delamination into 2D nanosheets. Layer-by-layer engineering of 2D perovskite nanosheets has a great potential for the rational design of new high-k dielectric/ferroelectric materials and nanodevices.

Minoru Osada

International Center for Materials Nanoarchitectonics (MANA)

National Institute for Materials Science (NIMS)

Chemical Synthesis of Porous Barium Titanate Thin Film and Thermal Stabilization of Ferroelectric Phase by Porosity-Induced Strain