The authors have no acknowledgements.

1. Design
<ol>
	<li>Fabrication of aluminum plates
	<ol>
		<li>Cut a 101 mm hole in the center of an aluminum plate of dimensions 150 mm x 200 mm x 2 mm to be used as the forefront plate with a laser processing machine. Machine claws at eight points to affix two rubber bands across the length, or two across the width of this plate (see Supplemental Figure 1A and Supplemental Figure 2A).</li>
		<li>Cut a 130 mm hole in the center of another 150 mm x 200 mm x 5 mm aluminum plate to be used as the middle upper plate with a laser processing machine. Machine eight notches for attaching rubber bands at two points across the length, or two across the width of this plate (see Supplemental Figure 1B and Supplemental Figure 2B).</li>
		<li>Cut a 130 mm hole in the center of a 150 mm x 200 mm x 4 mm aluminum plate to be used as the middle lower plate with a laser processing machine (see Supplemental Figure 1C and Supplemental Figure 2C).</li>
		<li>Cut a 30 mm hole in the center of a 150 mm x 200 mm x 1.5 mm aluminum plate to be used as the base plate (see Supplemental Figure 1D and Supplemental Figure 2D).</li>
	</ol>
	</li>
	<li>Fabrication of two aluminum pedestal
	<ol>
		<li>Cut a 30 mm hole in the center of the aluminum plate (100 mm diameter, 3 mm thickness) and make a notch from one side with the dimensions 42 mm wide x 30 mm deep (see Supplemental Figure 3A).</li>
		<li>Cut a 30 mm hole in the center of the plate in an aluminum plate (100 mm diameter, 4 mm thickness) and drill three 3 mm holes located 25 mm from the center, spaced 120&#176; from each other (see Supplemental Figure 3B).</li>
	</ol>
	</li>
	<li>Fabrication of three pressed cork disc
	<ol>
		<li>Cut a 20 mm hole in the center of the pressed cork disc (100 mm diameter, 2 mm thickness) with a water jet cutting machine. Make one cut 42 mm across x 30 mm deep, then one cut 4 mm wide x 5 mm deep (see Supplemental Figure 4A).</li>
		<li>Cut a 20 mm hole in the center of the pressed cork disc of dimensions 100 mm diameter, 1 mm thickness with a water jet cutting machine. Make a cut 42 mm across x 30 mm deep, a cut 4 mm wide x 40 mm deep (see Supplemental Figure 4B).</li>
		<li>Cut a pressed cork plate from a 100 mm diameter disc with a 42 mm width and 30 mm depth. Two sheets of 1 mm thickness and one sheet of 2 mm thickness are required (see Supplemental Figure 4C).</li>
	</ol>
	</li>
	<li>Fabrication of silicone rubber heater
	<ol>
		<li>Fabricate a heater using a 100 mm diameter disc of 2.5 mm thick silicon rubber with built-in Nichrome wire and cut a 20 mm hole in the center of the disc (see Supplemental Figure 5).</li>
	</ol>
	</li>
	<li>Assemble parts described in steps 1.1&#8211;1.4 by stacking them as shown in Supplemental Figure 6.</li>
	<li>To construct a microscope stage, refer to Supplemental Figure 6, cross-section of the microscope stage. Fix <img alt="Equation 1" src="/files/ftp_upload/59799/59799eq1.jpg" /> and <img alt="Equation 2" src="/files/ftp_upload/59799/59799eq2.jpg" />, then <img alt="Equation 3" src="/files/ftp_upload/59799/59799eq3.jpg" /> and <img alt="Equation 4" src="/files/ftp_upload/59799/59799eq4.jpg" /> with screws. Fix <img alt="Equation 4" src="/files/ftp_upload/59799/59799eq4.jpg" /> and <img alt="Equation 5" src="/files/ftp_upload/59799/59799eq5.jpg" /> with screws. Fix <img alt="Equation 2" src="/files/ftp_upload/59799/59799eq2.jpg" /> and <img alt="Equation 3" src="/files/ftp_upload/59799/59799eq3.jpg" />, <img alt="Equation 6" src="/files/ftp_upload/59799/59799eq6.jpg" /> and <img alt="Equation 5" src="/files/ftp_upload/59799/59799eq5.jpg" />, <img alt="Equation 6" src="/files/ftp_upload/59799/59799eq6.jpg" /> and <img alt="Equation 7" src="/files/ftp_upload/59799/59799eq7.jpg" />, <img alt="Equation 7" src="/files/ftp_upload/59799/59799eq7.jpg" /> and <img alt="Equation 8" src="/files/ftp_upload/59799/59799eq8.jpg" />, and <img alt="Equation 5" src="/files/ftp_upload/59799/59799eq5.jpg" /> and <img alt="Equation 9" src="/files/ftp_upload/59799/59799eq9.jpg" /> with adhesive.</li>
</ol>
2. Hardware design outlines
<ol>
	<li>Prepare a &#8220;power supply and programming circuit&#8221; as shown in Supplemental Figure 7. Supply 12 V DC to the heater controller from the J4 terminal connected to the AC adapter. Decrease the voltage from 12 V DC to 3.3 V DC for the circuit power supply using a regulator because the CPU supply voltage is 3.3 V DC. 
	NOTE: USB 1 is a terminal for 5 V DC and serial signal of development PC. Although 5 V DC is not essential, it is used as the power source to program the CPU. This is also converted to 3.3 V DC by the regulator. J1 is a control signal terminal at the time of programming. This circuit is housed in the controller case shown in Supplemental Figure 8.</li>
	<li>Prepare a &#8220;heater control circuit&#8221; as shown in Supplementary Figure 7. Switch to 12 V DC with Q5 (P channel MOS FET) and supply it to the heater. Q5 is a switching element that controls 12 V DC with PWM to adjust the amount of power supplied to the heater. 
	NOTE: The circuit includes an LED to visually confirm that voltage is being supplied to the heater. This drive signal (HEATER_C) is a PWM signal from the CPU. When an overheat signal is detected by the protection circuit, the BREAKER signal switches to LOW, and the operation of the MOS-FET stops. This circuit is housed in the controller case shown in Supplemental Figure 8.</li>
	<li>Prepare a &#8220;connector circuit for heater unit&#8221; as shown in Supplementary Figure 7. Install a USB connector for connection with the heater section. 
	NOTE: This circuit is housed in the controller case shown in Supplemental Figure 8.</li>
	<li>Prepare a &#8220;connector circuit for temperature sensor&#8221; as shown in Supplemental Figure 7. Mount the connector (Euroblock receptacle 2P) to connect the temperature sensor. 
	NOTE: This circuit is housed in the controller case shown in Supplemental Figure 8.</li>
	<li>For a &#8220;A/D converter&#8221; as shown in Supplemental Figure 7, use ADS 1015 as an AD conversion device. 
	NOTE: AD conversion device converts the values of the temperature sensor and overheat detection sensor from voltage to digital values. This is a 12-bit multiplexer AD conversion device and is connected to the CPU with the I2C interface. This circuit is housed in the controller case shown in Supplemental Figure 8.</li>
	<li>Make a &#8220;protect circuit&#8221; as shown in Supplemental Figure 7 by connecting the overheat detection sensor (OHS) signal to the inverting input of the OP amp. Compare this signal with the voltage of the trimmer resistor connected to the noninverting input.
	<ol>
		<li>Ensure that when the voltage becomes lower than the voltage of the trimmer resistor, the output of the OP amplifier goes HIGH, the connected NPN transistor Q2 turns ON and the BREAKER signal goes LOW.</li>
		<li>Ensure that at the same time, Q4 turns ON and the connected overheat indicator LED D6 lights up. 
		NOTE: This circuit is housed in the controller case shown in Supplemental Figure 8.</li>
	</ol>
	</li>
	<li>For a &#8220;display section&#8221; as shown in Supplemental Figure 7, use 192 x 64 dots for OLED. Connect with the CPU via the I2C interface.
	<ol>
		<li>Reset the OLED by separating the GND of the OLED by the CPU signal IO0 using an NPN transistor Q1 connected to the GND of the OLED. 
		NOTE: This OLED displays various types of information. This circuit is housed in the controller case shown in Supplemental Figure 8.</li>
	</ol>
	</li>
	<li>For a &#8220;LED &#38; rotary encoder with push switch&#8221; in Supplemental Figure 7, mount a rotary encoder by solder that functions as a push switch and incorporates two LEDs.
	<ol>
		<li>Connect one LED to VCC for use as a power LED. The other is connected to the CPU for use as an indicator during heater operation.</li>
		<li>Use a push switch contact for heater START/STOP that is connected to CPU. Connect the A and B outputs of the rotary encoder to the IO input set in the CPU interrupt. 
		NOTE: This circuit is housed in the controller case shown in Supplemental Figure 8.</li>
	</ol>
	</li>
	<li>For the CPU in Supplemental Figure 7, use the CPU of WROOM - 02D.
	<ol>
		<li>Output from IO12, IO13 to the &#8220;display unit&#8221; because the interface of the display is I2C standard. Connect IO0 to &#34;display unit&#34; and reset the OLED.</li>
		<li>Connect IO15 to &#34;heater control unit&#34; and control the power supplied to the heater by PWM output.</li>
		<li>Connect IO2 to &#34;LED &#38; rotary encoder with push switch&#34; and light the START LED. Connect IO4 and IO14 to &#34;LED &#38; rotary encoder with push switch&#34; and receive the signals (REA and REB) from the rotary encoder to determine the set temperature. Connect IO5 to &#34;LED &#38; rotary encoder with push switch&#34; and start/stop the heater.</li>
	</ol>
	</li>
</ol>
3. Software design outline
<ol>
	<li>Use Arduino CORE for WROOM - 02D for the CPU as the controller for this system. 
	NOTE: As input devices, the start/stop switch, rotary encoder, temperature sensor (thermistor) are used. As output devices, an LED, character display (OLED), and heater are used. The communication device uses Wi-Fi.</li>
	<li>Outline of the operation
	<ol>
		<li>Detect the operation of the rotary encoder as shown in the LED &#38; rotary encoder with the push switch in Supplemental Figure 7, store it as the set temperature, and display it on the OLED. Set the input terminal of the CPU to which the phase terminals REA and REB are connected as an interrupt input terminal and process the rotation (forward and reverse) of the rotary encoder by interrupt. Set it to +1 for forward rotation and -1 for reverse rotation. Write the set temperature to the global variable and use it for the heater temperature control. At the same time, update the set temperature display of the OLED.</li>
		<li>Identify start and stop by CPU IO 5 by start/stop switch (SW-S) as shown in the CPU of Supplemental Figure 7. The state of the start/stop switch is a timer interrupt process every 50 ms. 
		NOTE: Since the switch is a momentary switch, it reverses the state of start/stop when it is pushed and released. This state is stored in the global variable.</li>
		<li>Use a thermistor for the temperature sensor. Read the measured values from the sample sensor (refer to &#8220;connector circuit for heater connection&#8221; in Supplemental Figure 7) into the CPU after A/D converter (refer to &#8220;A/D converter&#8221; in Supplemental Figure 7). Supply the current to the heater by turning on the IO15 port in the &#8220;CPU&#8221; of Supplemental Figure 7. 
		NOTE: There are two types of temperature sensors. One is used to measure the temperature of the sample and control the heater on the set temperature, and the other is attached to a heater and used for heat prevention. Connect the thermistor to 3.3 V via a resistor and record the change in resistance as a change in voltage. Remove a noise by the moving average method.</li>
		<li>Use a thermistor for temperature prevention temperature sensor. Overheat detection is performed using a thermistor (R2) (&#8220;connector circuit for heater connection&#8221; in Supplemental Figure 7), and when the set value is exceeded, the heater current is shut off (&#8220;protect circuit&#8221; in Supplemental Figure 7). 
		NOTE: This sensor is incorporated into a circuit and not through the CPU. This sensor is independent from the CPU and compared with the resistance value set by the resistor trimmer by a differential amplifier in an analog manner. When it detects that the temperature has exceeded the set value, it intervenes in the FET switch, which controls the current to the heater and forcibly stops the current supply. The purpose is to prevent the temperature of the heater from exceeding a certain level even in a situation where the CPU does not work properly.</li>
		<li>Turn on the LED in the &#8220;LED &#38; rotary encoder with push switch&#8221; of the Supplemental Figure 7 by the CPU (in the &#8220;CPU&#8221; of Supplemental Figure 7), when the equipment is in operation.</li>
		<li>Display the set temperature and measured value to OLED in the &#34;display section&#34; of the Supplemental Figure 7 by the CPU (in the &#34;CPU &#34;of Supplemental Figure 7).</li>
		<li>Drive the FET switch in the &#34;heater control circuit&#34; of Supplemental Figure 7 with PWM from CPU to control the heater.</li>
		<li>Control the heater by PID, based on measured temperatures acquired by the temperature sensor. Use Arduino&#39;s pid_v1.h library for PID processing. 
		NOTE: The CPU calibrates the time, communicates with the server, transmits data, and receives instructions from the server. When the sensor temperature exceeds the set temperature, the current to the heater is set to 0, and overshoot is suppressed.</li>
		<li>Use the built-in Wi-Fi connection function of the CPU and connect to the Internet. Transmit set the temperature, heater temperature, etc. to the designated server by Wi-Fi.</li>
	</ol>
	</li>
</ol>
4. System configuration
<ol>
	<li>Build the system according to Supplemental Figure 9.</li>
	<li>Equip a Wi-Fi with the controller.</li>
	<li>Use a thermistor as a sensor for temperature measurement. Connect the thermistor wire to the &#34;SENSOR&#34; terminal on the controller case. Receive the temperature signal measured by the thermistor.</li>
	<li>Connect a microscope stage incorporating the rubber heater and the &#34;HEATER&#34; of the controller case with a dedicated cable. Control the current to the rubber heater.</li>
	<li>Change the set temperature with the knob on the controller. 
	NOTE: Temperature log monitoring, temperature setting can be operated remotely from a PC or smartphone.</li>
	<li>Transfer the measured temperature, set temperature, and time information at measurement from the controller to the server via the internet. The data measurement cycle time is 5 s and cycle time for data transfer to the server is 1 min.</li>
	<li>Access the server from the controller side at regular intervals and transfer the measurement data stored in the CPU of the controller to the server for analysis and graphing.</li>
	<li>Refer to the supplementary material for how to operate the server.</li>
</ol>
5. Design of the sideways inverted microscope
<ol>
	<li>Fix two aluminum plates of 15 mm in thickness vertically with screws to create a basic mount.</li>
	<li>Attach a jig (one place) to the horizontal part of the base mount.</li>
	<li>Place the microscope stage part vertically, attach the jigs (two places) to the vertical part of the base stand and fix the bottom of the microscope to the base stand.</li>
	<li>Fix the microscope stage with screws.</li>
</ol>
6. Method of operation
NOTE: Here, the sample used is a mixture of Bold Modified Basal Freshwater Nutrient Solution liquid culture medium, sodium metasilicate, vitamins, and sterile water. 800 &#956;L of this sample is diluted in 10 mL of fresh water medium.
<ol>
	<li>Observation method
	<ol>
		<li>Inject 1,000 &#956;L of the prepared sample into a self-made glass chamber. 
		NOTE: The self-made glass chamber arranges two slide glasses in parallel and fixes them with an adhesive. A normal Petri dish has a large thickness and cells escape in the depth direction in the chamber, making it difficult to observe with a microscope. To prevent this, the chamber with a small depth direction is made, which makes it possible to prevent the cells from escaping in the depth direction in the chamber. A low temperature curable epoxy resin adhesive is used to bond around the glass to prevent the sample dropping from the chamber.</li>
		<li>Attach a separately prepared video camera to the microscope. Connect a video camera using the microscope&#39;s dedicated lens adapter and shoot the sample.</li>
		<li>Use a microscope with a 10x eyepiece and 200x objective.</li>
		<li>Attach the vertical microscope stage to a microscope in four locations with 4 mm screws. 
		NOTE: Refer to Supplemental Figure 1A and Supplemental Figure 2A for design drawings of aluminum plates. In this experiment, an inverted microscope was used. This was tilted by 90&#176;, and the fabricated microscope stage was affixed with screws. Refer to Figure 1.</li>
		<li>Secure the sample with two rubber bands using the four claws made lengthwise. Place a sample on a microscope stage perpendicular to the ground surface.</li>
		<li>Set the temperature to 40 &#176;C with the controller shown in Supplemental Figure 8. Turn the controller knob to set the temperature. Check the set temperature on the display. Press the knob to start temperature control, and the blue LED will light up. Press the knob again to turn off the LED and stop temperature control. 
		NOTE: The measured temperature is displayed in real-time, and the heater is controlled to reach the set temperature. When the temperature control starts, the blue LED lights up and remains so while the heater is in operation. When the heater overheats, the red LED lights, and the heater automatically stops.</li>
		<li>Refer to &#34;The Server Operation Manual&#34; in the supplementary information for server operation. 
		NOTE: A server for data storage is required. The server&#39;s database uses My-SQL.</li>
	</ol>
	</li>
</ol>
7. Measurement of surface temperature distribution of rubber heater
<ol>
	<li>Measure the distribution of the rubber heater surface temperature by thermography to check the temperature uniformity.</li>
	<li>Attach the microscope stage which incorporated a rubber heater with a stand.</li>
	<li>Change the setting temperature of the rubber heater surface to 35 &#176;C, 45 &#176;C, 55 &#176;C, and 65 &#176;C, and measure by the thermography from the front (refer to Supplemental Figure 10).</li>
</ol>
8. Temperature response test
<ol>
	<li>Start temperature control by setting the sample set temperature to 30 &#176;C. Wait until the measurement value reaches 30 &#176;C and stabilizes. Increase the preset temperature stepwise by 5 &#176;C from 30 &#176;C to 50 &#176;C and wait until the measured value stabilizes following the respective preset temperature.</li>
	<li>Decrease the preset temperature stepwise by 5 &#176;C from 50 &#176;C to 30 &#176;C and detect the tracking ability of the measured value.</li>
</ol>

<ol><li>Drum, R. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Electron+Microscope+Observations+of+Diatos%5BTitle%5D)+AND+%22Osterreichische+Botanische+Zeitschrift%22%5BJournal%5D)">Electron Microscope Observations of Diatos.</a> Osterreichische Botanische Zeitschrift. 116, 321(1969).</li>
<li>McBride, T. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Preparing+Random+Distributions+of+Datom+Values+on+Microscope+Slides%5BTitle%5D)+AND+%22Limnology+and+Oceangraphy%22%5BJournal%5D)">Preparing Random Distributions of Datom Values on Microscope Slides.</a> Limnology and Oceangraphy. 33, 1627-1629 (1988).</li>
<li>Liu, X. Y., Lu, Z., Sun, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Orientation+Control+of+Biological+Cells+Under+Inverted+Microscopy%5BTitle%5D)+AND+%22IEEE-ASME+Transactions+on+Mechatronics%22%5BJournal%5D)">Orientation Control of Biological Cells Under Inverted Microscopy.</a> IEEE-ASME Transactions on Mechatronics. 16, 918-924 (2011).</li>
<li>Kahle, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Applications+of+a+Compact%2C+Easy-to-Use+Inverted+Fluorescence+Microscope%5BTitle%5D)+AND+%22American+Laboratory%22%5BJournal%5D)">Applications of a Compact, Easy-to-Use Inverted Fluorescence Microscope.</a> American Laboratory. 43, 11-14 (2011).</li>
<li>Prunet, N., Jack, T. P., Meyerowitz, E. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Live+confocal+imaging+of+Arabidopsis+flower+buds%5BTitle%5D)+AND+%22Developmental+Biology%22%5BJournal%5D)">Live confocal imaging of Arabidopsis flower buds.</a> Developmental Biology. , 114-120 (2016).</li>
<li>Nimchuk, Z. L., Perdue, T. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Live+Imaging+of+Shoot+Meristems+on+an+Inverted+Confocal+Microscope+Using+an+Objective+Lens+Inverter+Attachment%5BTitle%5D)+AND+%22Frontiers+in+Plant+Science%22%5BJournal%5D)">Live Imaging of Shoot Meristems on an Inverted Confocal Microscope Using an Objective Lens Inverter Attachment.</a> Frontiers in Plant Science. 8, 10(2017).</li>
<li>Hedde, P. N., Malacrida, L., Ahrar, S., Siryaporn, A., Gratton, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((sideSPIM+-+selective+plane+illumination+based+on+a+conventional+inverted+microscope%5BTitle%5D)+AND+%22Biomedical+Optics+Express%22%5BJournal%5D)">sideSPIM - selective plane illumination based on a conventional inverted microscope.</a> Biomedical Optics Express. 8, 3918-3937 (2017).</li>
<li>Crowe, W. E., Wills, N. K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((A+simple+Method+for+Monitoring+Changes+in+Cell+Height+using+Fluorescent+Microbeads+and+an+Ussing-type+Chamber+for+the+Inverted+Microscope%5BTitle%5D)+AND+%22Pflugers+Archiv-Europian+journal+of+Physiology%22%5BJournal%5D)">A simple Method for Monitoring Changes in Cell Height using Fluorescent Microbeads and an Ussing-type Chamber for the Inverted Microscope.</a> Pflugers Archiv-Europian journal of Physiology. , 349-357 (1991).</li>
<li>Bavister, B. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((A+Minichamber+Device+for+Maintaining+a+Constant+Carbon-Dioxide+in+Air+Atmosphere+during+Prolonged+Culture+of+Cells+on+the+Stage+of+an+Inverted+Microscope%5BTitle%5D)+AND+%22In+Vitro+Cellular+%26+Developmental+Biology%22%5BJournal%5D)">A Minichamber Device for Maintaining a Constant Carbon-Dioxide in Air Atmosphere during Prolonged Culture of Cells on the Stage of an Inverted Microscope.</a> In Vitro Cellular & Developmental Biology. 24, 759-763 (1988).</li>
<li>Makler, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((A+New+version+of+the+10-MU-M+Chamber+and+its+use+for+Semen+Analysis+with+Inverted+Microscope%5BTitle%5D)+AND+%22Archives+of+Andrology%22%5BJournal%5D)">A New version of the 10-MU-M Chamber and its use for Semen Analysis with Inverted Microscope.</a> Archives of Andrology. 13, 195-197 (1984).</li>
<li>Xu, Z., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Flexible+microassembly+methods+for+micro%2Fnanofluidic+chips+with+an+inverted+microscope%5BTitle%5D)+AND+%22Microelectronic+Engineering%22%5BJournal%5D)">Flexible microassembly methods for micro/nanofluidic chips with an inverted microscope.</a> Microelectronic Engineering. 97, 1-7 (2012).</li>
<li>Datyner, N. B., Gintant, G. A., Cohen, I. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Versatile+Temperature+Controlled+Tissue+Bath+for+Studies+of+Isolated+Cells+using+an+Inverted+Microscope%5BTitle%5D)+AND+%22Pflugers+Archive-+Europian+Journal+of+Physiology%22%5BJournal%5D)">Versatile Temperature Controlled Tissue Bath for Studies of Isolated Cells using an Inverted Microscope.</a> Pflugers Archive- Europian Journal of Physiology. 403, 318-323 (1985).</li>
<li>Claudet, C., Bednar, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Magneto-optical+tweezers+built+around+an+inverted+microscope%5BTitle%5D)+AND+%22Applied+Optics%22%5BJournal%5D)">Magneto-optical tweezers built around an inverted microscope.</a> Applied Optics. 44, 3454-3457 (2005).</li>
<li>Yamaoka, N., Suetomo, Y., Yoshihisa, T., Sonobe, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Motion+analysis+and+ultrastructural+study+of+a+colonial+diatom%2C+Bacillaria+paxillifer%5BTitle%5D)+AND+%22Microscopy%22%5BJournal%5D)">Motion analysis and ultrastructural study of a colonial diatom, Bacillaria paxillifer.</a> Microscopy. 65, 211-221 (2016).</li>
<li>Apoya-Horton, M. D., Yin, L., Underwood, G. J. C., Gretz, M. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Movement+modalities+and+responses+to+environmental+changes+of+the+mudflat+diatom+Cylindrotheca+closterium+%28Bacillariophyceae%29%5BTitle%5D)+AND+%22Journal+of+Phycology%22%5BJournal%5D)">Movement modalities and responses to environmental changes of the mudflat diatom Cylindrotheca closterium (Bacillariophyceae).</a> Journal of Phycology. 42, 379-390 (2006).</li>
<li>Bannon, C. C., Campbell, D. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Sinking+towards+destiny%3A+High+throughput+measurement+of+phytoplankton+sinking+rates+through+time-resolved+fluorescence+plate+spectroscopy%5BTitle%5D)+AND+%22PLoS+One%22%5BJournal%5D)">Sinking towards destiny: High throughput measurement of phytoplankton sinking rates through time-resolved fluorescence plate spectroscopy.</a> PLoS One. 12, 16(2017).</li>
<li>Clarkson, N., Davies, M. S., Dixey, R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Diatom+motility+and+low+frequency+electromagnetic+fields+-+A+new+technique+in+the+search+for+independent+replication+of+results%5BTitle%5D)+AND+%22Bioelectromagnetics%22%5BJournal%5D)">Diatom motility and low frequency electromagnetic fields - A new technique in the search for independent replication of results.</a> Bioelectromagnetics. 20, 94-100 (1999).</li>
<li>Iwasa, K., Shimizu, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Motility+of+Diatom%2C+Phaeodactylum-Tricornutum%5BTitle%5D)+AND+%22Experimental+Cell+Research%22%5BJournal%5D)">Motility of Diatom, Phaeodactylum-Tricornutum.</a> Experimental Cell Research. 74, (1972).</li>
<li>Edgar, L. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Mucilage+Secretions+of+Moving+Diatoms%5BTitle%5D)+AND+%22Protoplasma%22%5BJournal%5D)">Mucilage Secretions of Moving Diatoms.</a> Protoplasma. 118, 44-48 (1983).</li>
<li>Edgar, L. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Diatom+Locomotion%5BTitle%5D)+AND+%22Computer-Assisted+Analysis+of+Cine+Film+British+Phycological+Journal%22%5BJournal%5D)">Diatom Locomotion.</a> Computer-Assisted Analysis of Cine Film British Phycological Journal. 14, 83-101 (1979).</li>
<li>Iversen, M. H., Ploug, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Temperature+effects+on+carbon-specific+respiration+rate+and+sinking+velocity+of+diatom+aggregates+-+potential+implications+for+deep+ocean+export+processes%5BTitle%5D)+AND+%22Biogeosciences%22%5BJournal%5D)">Temperature effects on carbon-specific respiration rate and sinking velocity of diatom aggregates - potential implications for deep ocean export processes.</a> Biogeosciences. 10, 4073-4085 (2013).</li>
<li>Riebesell, U. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Comparison+of+Sinking+and+Sedimentation-Rate+Measurements+in+a+Diatom+Winter+Spring+Bloom%5BTitle%5D)+AND+%22Marine+Ecology+Progress+Series%22%5BJournal%5D)">Comparison of Sinking and Sedimentation-Rate Measurements in a Diatom Winter Spring Bloom.</a> Marine Ecology Progress Series. 54, 109-119 (1989).</li>
<li>Drum, R. W., Hopkins, J. T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Diatom+Locomotion+-+An+Explanation%5BTitle%5D)+AND+%22Protoplasma%22%5BJournal%5D)">Diatom Locomotion - An Explanation.</a> Protoplasma. 62, (1966).</li>
</ol>

The authors have no conflicts to disclose.

Trajectory analysis of moving diatom cells is a useful approach to evaluating diatom motility. However, while a normal inverted microscope observes samples horizontally, it is not suitable for observations of the influence of gravity or floating movement in the vertical direction. Developed and described here is a vertical microscope stage with temperature control and attached to an inverted microscope, which has been rotated by 90&#176;. This microscope stage with temperature control allows observation of temperature-de...

Optical microscopy is a technique employed to increase observable details via magnification of a sample with lenses and visible light. In optical microscopy, light is directed onto a sample, then transmitted, reflected, or fluorescent light is captured by magnifying lenses for observation. Various types of microscope are available that differ in design to accommodate different uses and observation methods. The different designs include an upright microscope, which is structured to illuminate a sample from below for observation from above, and an inverted microscope, which illuminates the sample from above for observation from below. Upright microscopes are the most common and widely used design. Inverted microscopes are often used to observe samples that cannot allow a lens close in distance from above, such as cultured cells adherent to the bottom of a container. Many research groups have reported observations in a wide range of fields using inverted microscopes1,2,3,4,5,6,7. Many additional devices have also been developed that take advantage of the features of inverted microscopes8,9,10,11,12,13.
Currently, in all conventional microscope designs, the microscope stage is horizontal and is therefore unsuitable for the observation of samples producing movement in the vertical plane, (due to gravity, buoyancy, motion, etc.). To make these observations possible, the microscope stage and light path must be rotated to vertical. The vertical stage is required to vertically mount glass slides or sample containers such as a Petri dishes to the stage. To address this, a sideways inverted microscope tilted by 90&#176; has already been devised. However, attaching samples with tape or other adhesives does not yield the necessary long-term immobility. Described here is a device that can achieve the necessary stability. This device permits observation over time of sample movement in the vertical plane. Mounting of a silicon rubber heater has also made it possible to observe the influence of temperature variation on sample behavior. Temperature data is transferred to an internet server by Wi-Fi, and temperature settings and log monitoring can be controlled remotely from a PC or smartphone. To our knowledge, the stage attached to a sideways tilted microscope tilted by 90&#176; has not yet been reported in previous studies.
The microscope stage is composed of three aluminum plates. The middle aluminum plate is mounted to the lower aluminum plate that attaches to the stage. The silicone rubber containing the temperature sensor is attached between the middle and upper aluminum plates. Rubber bands are used to affix the sample. Claws are attached in the left and right four points of the upper aluminum plate to secure the rubber bands. The control circuit of the temperature regulator receives a signal from the temperature sensor embedded in silicone rubber and modulates electric power by the pulse width modulation (PWM) method. The temperature can be gradually increased to 50 &#176;C in 1 &#176;C increments. This device is useful for applications in which vertical sample motions may be temperature-dependent.
This report provides examples of temperature effects on the floating phenomenon of diatoms. As examples of diatom observation studies, measurements of sedimentation velocity of cell clusters, motion analyses, ultrafine structure studies, etc. have been reported14,15,16,17,18,19,20,21,22,23. The specific gravity of diatoms floating in water with photosynthetic organisms is slightly higher than that of water, so they tend to sink; however, they will rise if even slight convection is occurring. To study this phenomenon, a glass slide is affixed vertically to a microscope stage, and the effects of increasing temperature on diatom vertical motion are observed.

<table><tbody><tr><td>AC adapter 12V2A</td><td>Akizuki Denshi Tsusho Co., Ltd.</td><td>AD-D120P200</td><td>Tokyo, Japan</td></tr><tr><td>ADS1015 Substrate</td><td>Akizuki Denshi Tsusho Co., Ltd.</td><td>adafruit PRODUCT ID: 1083</td><td>Tokyo, Japan</td></tr><tr><td>Alminium Plate (Back Side Plate)</td><td>Inoval Co., Ltd.</td><td>W 150mm&amp;times;L 200?&amp;times;T 1.5mm</td><td>Gifu, Japan</td></tr><tr><td>Alminium Plate (Forefront Plate)</td><td>Inoval Co., Ltd.</td><td>W 150mm&amp;times;L 200?&amp;times;T 2mm</td><td>Gifu, Japan</td></tr><tr><td>Alminium Plate (Middle Lower Plate)</td><td>Inoval Co., Ltd.</td><td>W 150mm&amp;times;L 200?&amp;times;T 4mm</td><td>Gifu, Japan</td></tr><tr><td>Alminium Plate (Middle Upper Plate)</td><td>Inoval Co., Ltd.</td><td>W 150mm&amp;times;L 200?&amp;times;T 5mm</td><td>Gifu, Japan</td></tr><tr><td>Aluminum Pedestal (Lower Plate)</td><td>Inoval Co., Ltd.</td><td>D 100mm&amp;times;T 3mm (30&amp;Phi;)</td><td>Gifu, Japan</td></tr><tr><td>Aluminum Pedestal (Upper Plate)</td><td>Inoval Co., Ltd.</td><td>D 100mm&amp;times;T 3mm (30&amp;Phi;)</td><td>Gifu, Japan</td></tr><tr><td>Bold Modified Basal Freshwater Nutrient Solution</td><td>Sigma-Aldrich Co. LLC</td><td>B5282-500ML</td><td>St. Louis, USA</td></tr><tr><td>Controller Case</td><td>Marutsu Elec Co., Ltd.</td><td>pff-13-3-9</td><td>Tokyo, Japan</td></tr><tr><td>CPU</td><td>Akizuki Denshi Tsusho Co., Ltd.</td><td>ESP-WROOM-02D</td><td>Tokyo, Japan</td></tr><tr><td>Inverted microscope</td><td>Olympus Corporation</td><td>CKX 53</td><td>Tokyo, Japan</td></tr><tr><td>Low temperature hardening epoxy resin adhesive</td><td>ThreeBond Co., Ltd.</td><td>TB2086M</td><td>Tokyo, Japan</td></tr><tr><td>Multi-turn semi-fixed volume Vertical type 500 &amp;Omega;</td><td>Akizuki Denshi Tsusho Co., Ltd.</td><td>3296W-1-501LF</td><td>Tokyo, Japan</td></tr><tr><td>OLED module</td><td>Akihabara Inc.</td><td>M096P4W</td><td>Tokyo, Japan</td></tr><tr><td>Pressed Cork (For supporting electrode )</td><td>Tera Co., Ltd.</td><td>W 42mm&amp;times;L 30?</td><td>Ishikawa, Japan</td></tr><tr><td>Pressed Cork (Lower Disk)</td><td>Tera Co., Ltd.</td><td>D 100mm&amp;times;T 0.5mm (20&amp;Phi;)</td><td>Ishikawa, Japan</td></tr><tr><td>Pressed Cork (Upper Disk)</td><td>Tera Co., Ltd.</td><td>D 100mm&amp;times;T 2.5mm (20&amp;Phi;)</td><td>Ishikawa, Japan</td></tr><tr><td>Rotary encoder with switch with 2 color LED</td><td>Akizuki Denshi Tsusho Co., Ltd.</td><td>P-05772</td><td>Tokyo, Japan</td></tr><tr><td>Silicone rubber heater</td><td>Three High Co., Ltd.</td><td>D 100mm&amp;times;T 2.5mm (20&amp;Phi;)</td><td>Kanagawa, Japan</td></tr><tr><td>Substrate</td><td>Seeed Technology Co., Ltd.</td><td>mh5.0</td><td>Shenzhen, China</td></tr><tr><td>Temperature sensor</td><td>Akizuki Denshi Tsusho Co., Ltd.</td><td>NXFT15XH103FA2B050</td><td>Tokyo, Japan</td></tr><tr><td>Three-terminal DC / DC regulator 3.3 V</td><td>Marutsu Elec Co., Ltd.</td><td>BR301</td><td>Tokyo, Japan</td></tr><tr><td>Universal Flexible Arm</td><td>Banggood Technology Co., Ltd.</td><td>YP-003-2</td><td>Hong Kong, China</td></tr><tr><td>USB cable USB-A - MicroUSB</td><td>Akizuki Denshi Tsusho Co., Ltd.</td><td>USB CABLE A-MICROB</td><td>Tokyo, Japan</td></tr><tr><td>Video Canera</td><td>Sony Corporation</td><td>HDR-CX590</td><td>Tokyo, Japan</td></tr></tbody></table>

fabrication of microscope stage for vertical observation with temperature control function

Samples are usually placed onto a horizontal microscope stage for microscopic observation. However, to observe the influence of gravity on a sample or study afloat behavior, it is necessary to make the microscope stage vertical. To accomplish this, a sideways inverted microscope tilted by 90&#176; has been devised. To observe samples with this microscope, sample containers such as Petri dishes or glass slides must be secured to the stage vertically. A device that can secure sample containers in place on a vertical microscope stage has been developed and is described here. Attachment of this device to the stage allows observation of sample dynamics in the vertical plane. The ability to regulate temperature using a silicone rubber heater also permits observation of temperature-dependent sample behaviors. Furthermore, the temperature data is transferred to an internet server. Temperature settings and log monitoring can be controlled remotely from a PC or smartphone.

Figure 2 shows the temperature distribution of the rubber heater. The surface temperature of the rubber heater was uniform at each temperature. Figure 3 shows the responsiveness of the measured temperature to set temperature changes. The orange line shows the set temperature and blue line shows the change of the sample temperature. The overshoot of the measured value to the setting change is small and the tracking is quick.
<...

Watch this Scientific Journal Video about Fabrication of Microscope Stage for Vertical Observation with Temperature Control Function at JoVE.com

Fabrication of Microscope Stage for Vertical Observation with Temperature Control Function

Presented here is a protocol using a temperature-controlled microscope stage that allows a sample container to be mounted on a vertical microscope.

Samples are usually placed onto a horizontal microscope stage for microscopic observation. However, to observe the influence of gravity on a sample or ...

fabrication-microscope-stage-for-vertical-observation-with

Research

JoVE Journal

Engineering

7.4K Views.  Tokyo University of Science. Dit apparaat kan worden gebruikt om een monster vast te stellen aan een verticale microscoop stadium om observatie van de invloed van de zwaartekracht en het werken aan het monster van belang. Bevestiging van dit apparaat aan het stadium maakt het mogelijk de monsterdynamiek in het verticale frame te observeren en maakt het mogelijk temperatuurafhankelijk monstergedrag te observeren. Om de aluminium platen te fabriceren, gebruik maken van een laser processing machine om een 101-millimeter gat...

Video: Fabrication of Microscope Stage for Vertical Observation with Temperature Control Function

Low-Cost Cryo-Light Microscopy Stage Fabrication for Correlated Light/Electron Microscopy

The coupling of cryo-light microscopy (cryo-LM) and cryo-electron microscopy (cryo-EM) poses a number of advantages for understanding cellular 
dynamics and ultrastructure. First, cells can be imaged in a near native environment for both techniques. Second, due to the vitrification process, samples are
 preserved by rapid physical immobilization rather than slow chemical fixation. Third, imaging the same sample with both cryo-LM and cryo-EM provides correlation of
 data from a single cell, rather than a comparison of "representative samples". While these benefits are well known from prior studies, the widespread use of correlative 
 cryo-LM and cryo-EM remains limited due to the expense and complexity of buying or building a suitable cryogenic light microscopy stage. Here we demonstrate the 
 assembly, and use of an inexpensive cryogenic stage that can be fabricated in any lab for less than $40 with parts found at local hardware and grocery stores. This 
 cryo-LM stage is designed for use with reflected light microscopes that are fitted with long working distance air objectives. For correlative cryo-LM and cryo-EM 
 studies, we adapt the use of carbon coated standard 3-mm cryo-EM grids as specimen supports. After adsorbing the sample to the grid, previously established protocols 
 for vitrifying the sample and transferring/handling the grid are followed to permit multi-technique imaging. As a result, this setup allows any laboratory with a 
 reflected light microscope to have access to direct correlative imaging of frozen hydrated samples.

We demonstrate the fabrication of a low-cost cryogenic stage designed to fit most reflected light microscopes. This lab-built cryogenic stage enables efficient and reliable correlative imaging between cryo-light and cryo-electron microscopy.

The coupling of cryo-light microscopy (cryo-LM) and cryo-electron microscopy (cryo-EM) poses a number of advantages for understanding cellular 
dynamics ...

Bioengineering

Fabrication and Testing of Photonic Thermometers

In recent years, a push for developing novel silicon photonic devices for telecommunications has generated a vast knowledge base that is now being leveraged for developing sophisticated photonic sensors. Silicon photonic sensors seek to exploit the strong confinement of light in nano-waveguides to transduce changes in physical state to changes in resonance frequency. In the case of thermometry, the thermo-optic coefficient, i.e., changes in refractive index due to temperature, causes the resonant frequency of the photonic device such as a Bragg grating to drift with temperature. We are developing a suite of photonic devices that leverage recent advances in telecom compatible light sources to fabricate cost-effective photonic temperature sensors, which can be deployed in a wide variety of settings ranging from controlled laboratory conditions, to the noisy environment of a factory floor or a residence. In this manuscript, we detail our protocol for the fabrication and testing of photonic thermometers.

We describe the process of fabrication and testing of photonic thermometers.

In recent years, a push for developing novel silicon photonic devices for telecommunications has generated a vast knowledge base that is now being ...

Chemistry

Fabricating van der Waals Heterostructures with Precise Rotational Alignment

In this work we describe a technique for creating new crystals (van der Waals heterostructures) by stacking distinct ultrathin layered 2D materials. We demonstrate not only lateral control but, importantly, also control over the angular alignment of adjacent layers. The core of the technique is represented by a home-built transfer setup which allows the user to control the position of the individual crystals involved in the transfer. This is achieved with sub-micrometer (translational) and sub-degree (angular) precision. Prior to stacking them together, the isolated crystals are individually manipulated by custom-designed moving stages that are controlled by a programmed software interface. Moreover, since the entire transfer setup is computer controlled, the user can remotely create precise heterostructures without coming into direct contact with the transfer setup, labeling this technique as &#8220;hands-free&#8221;. In addition to presenting the transfer set-up, we also describe two techniques for preparing the crystals that are subsequently stacked.

In this work we describe a technique that is used to create new crystals (van der Waals heterostructures) by stacking ultrathin layered 2D materials with precise control over position and relative orientation.

In this work we describe a technique for creating new crystals (van der Waals heterostructures) by stacking distinct ultrathin layered 2D materials. We ...

Controlling Flow Speeds of Microtubule-Based 3D Active Fluids Using Temperature

We present a method for using temperature to tune the flow speeds of kinesin-driven, microtubule-based three-dimensional (3D) active fluids. This method allows for tuning the speeds in situ without the need to manufacture new samples to reach different desired speeds. Moreover, this method enables the dynamic control of speed. Cycling the temperature leads the fluids to flow fast and slow, periodically. This controllability is based on the Arrhenius characteristic of the kinesin-microtubule reaction, demonstrating a controlled mean flow speed range of 4&#8211;8 &#181;m/s. The presented method will open the door to the design of microfluidic devices where the flow rates in the channel are locally tunable without the need for a valve.

The goal of this protocol is to use temperature to control the flow speeds of three-dimensional active fluids. The advantage of this method not only allows for regulating flow speeds in situ but also enables dynamic control, such as periodically tuning flow speeds up and down.

We present a method for using temperature to tune the flow speeds of kinesin-driven, microtubule-based three-dimensional (3D) active fluids. This method ...

A Guide to Build a Highly Inclined Swept Tile Microscope for Extended Field-of-view Single-molecule Imaging

Single-molecule imaging has greatly advanced our understanding of molecular mechanisms in biological studies. However, it has been challenging to obtain large field-of-view, high-contrast images in thick cells and tissues. Here, we introduce highly inclined swept tile (HIST) microscopy that overcomes this problem. A pair of cylindrical lenses was implemented to generate an elongated excitation beam that was scanned over a large imaging area via a fast galvo mirror. A 4f configuration was used to position optical components. A scientific complementary metal-oxide semiconductor camera detected the fluorescence signal and blocked the out-of-focus background with a dynamic confocal slit synchronized with the beam sweeping. We present a step-by-step instruction on building the HIST microscope with all basic components.

A detailed instruction is described on how to build a highly inclined swept tile (HIST) microscope and its usage for single-molecule imaging.

Single-molecule imaging has greatly advanced our understanding of molecular mechanisms in biological studies. However, it has been challenging to obtain ...

Temperature-Controlled Assembly and Characterization of a Droplet Interface Bilayer

The droplet interface bilayer (DIB) method for assembling lipid bilayers (i.e., DIBs) between lipid-coated aqueous droplets in oil offers key benefits versus other methods: DIBs are stable and often long-lasting, bilayer area can be reversibly tuned, leaflet asymmetry is readily controlled via droplet compositions, and tissue-like networks of bilayers can be obtained by adjoining many droplets. Forming DIBs requires spontaneous assembly of lipids into high density lipid monolayers at the surfaces of the droplets. While this occurs readily at room temperature for common synthetic lipids, a sufficient monolayer or stable bilayer fails to form at similar conditions for lipids with melting points above room temperature, including some cellular lipid extracts. This behavior has likely limited the compositions&#8212;and perhaps the biological relevance&#8212;of DIBs in model membrane studies. To address this problem, an experimental protocol is presented to carefully heat the oil reservoir hosting DIB droplets and characterize the effects of temperature on the lipid membrane. Specifically, this protocol shows how to use a thermally conductive aluminum fixture and resistive heating elements controlled by a feedback loop to prescribe elevated temperatures, which improves monolayer assembly and bilayer formation for a wider set of lipid types. Structural characteristics of the membrane, as well as the thermotropic phase transitions of the lipids comprising the bilayer, are quantified by measuring the changes in electrical capacitance of the DIB. Together, this procedure can aid in evaluating biophysical phenomena in model membranes over various temperatures, including determining an effective melting temperature (TM) for multi-component lipid mixtures. This capability will thus allow for closer replication of natural phase transitions in model membranes and encourage the formation and use of model membranes from a wider swath of membrane constituents, including those that better capture the heterogeneity of their cellular counterparts.

This protocol details the use of a feedback temperature-controlled heating system to promote lipid monolayer assembly and droplet interface bilayer formation for lipids with elevated melting temperatures, and capacitance measurements to characterize temperature-driven changes in the membrane.

The droplet interface bilayer (DIB) method for assembling lipid bilayers (i.e., DIBs) between lipid-coated aqueous droplets in oil offers key benefits ...

A Flexible Chamber for Time-Lapse Live-Cell Imaging with Stimulated Raman Scattering Microscopy

Stimulated Raman scattering (SRS) microscopy is a label-free chemical imaging technology. Live-cell imaging with SRS has been demonstrated for many biological and biomedical applications. However, long-term time-lapse SRS imaging of live cells has not been widely adopted. SRS microscopy often uses a high numerical aperture (NA) water-immersion objective and a high NA oil-immersion condenser to achieve high-resolution imaging. In this case, the gap between the objective and the condenser is only a few millimeters. Therefore, most commercial stage-top environmental chambers cannot be used for SRS imaging because of their large thickness with a rigid glass cover. This paper describes the design and fabrication of a flexible chamber that can be used for time-lapse live-cell imaging with transmitted SRS signal detection on an upright microscope frame. The flexibility of the chamber is achieved by using a soft material - a thin natural rubber film. The new enclosure and chamber design can be easily added to an existing SRS imaging setup. The testing and preliminary results demonstrate that the flexible chamber system enables stable, long-term, time-lapse SRS imaging of live cells, which can be used for various bioimaging applications in the future.

We report a stage-top, flexible environmental chamber for time-lapse imaging of live cells using upright stimulated Raman scattering microscopy with transmitted signal detection. Lipid droplets were imaged in SKOV3 cells treated with oleic acid for up to 24 h with a 3 min time interval.

Stimulated Raman scattering (SRS) microscopy is a label-free chemical imaging technology. Live-cell imaging with SRS has been demonstrated for many ...

Nasal Brushing Sampling and Processing Using Digital High Speed Ciliary Videomicroscopy &ndash; Adaptation for the COVID-19 Pandemic

Primary Ciliary Dyskinesia (PCD) is a genetic motile ciliopathy, leading to significant otosinopulmonary disease. PCD diagnosis is often missed or delayed due to challenges with different diagnostic modalities. Ciliary videomicroscopy, using Digital High-Speed Videomicroscopy (DHSV), one of the diagnostic tools for PCD, is considered the optimal method to perform ciliary functional analysis (CFA), comprising of ciliary beat frequency (CBF) and beat pattern (CBP) analysis. However, DHSV lacks standardized, published operating procedure for processing and analyzing samples. It also uses living respiratory epithelium, a significant infection control issue during the COVID-19 pandemic. To continue providing a diagnostic service during this health crisis, the ciliary videomicroscopy protocol has been adapted to include adequate infection control measures.
Here, we describe a revised protocol for sampling and laboratory processing of ciliated respiratory samples, highlighting adaptations made to comply with COVID-19 infection control measures. Representative results of CFA from nasal brushing samples obtained from 16 healthy subjects, processed and analyzed according to this protocol, are described. We also illustrate the importance of obtaining and processing optimal quality epithelial ciliated strips, as samples not meeting quality selection criteria do now allow for CFA, potentially decreasing the diagnostic reliability and the efficiency of this technique.

Nasal Brushing Sampling and Processing Using Digital High Speed Ciliary Videomicroscopy &#8211; Adaptation for the COVID-19 Pandemic

To guarantee a successful and high-quality ciliary functional analysis for PCD diagnosis, a precise and careful method for respiratory epithelium sampling and processing is essential. To continue providing PCD diagnostic service during the COVID-19 pandemic, the ciliary videomicroscopy protocol has been updated to include appropriate infection control measures.

Primary Ciliary Dyskinesia (PCD) is a genetic motile ciliopathy, leading to significant otosinopulmonary disease. PCD diagnosis is often missed or delayed ...

Immunology and Infection

Microperfusion Technique to Investigate Regulation of Microvessel Permeability in Rat Mesentery

Experiments to measure the permeability properties of individually perfused microvessels provide a bridge between investigation of molecular and cellular mechanisms regulating vascular permeability in cultured endothelial cell monolayers and the functional exchange properties of whole microvascular beds. A method to cannulate and perfuse venular microvessels of rat mesentery and measure the hydraulic conductivity of the microvessel wall is described. The main equipment needed includes an intravital microscope with a large modified stage that supports micromanipulators to position three different microtools: (1) a beveled glass micropipette to cannulate and perfuse the microvessel; (2) a glass micro-occluder to transiently block perfusion and enable measurement of transvascular water flow movement at a measured hydrostatic pressure, and (3) a blunt glass rod to stabilize the mesenteric tissue at the site of cannulation. The modified Landis micro-occlusion technique uses red cells suspended in the artificial perfusate as markers of transvascular fluid movement, and also enables repeated measurements of these flows as experimental conditions are changed and hydrostatic and colloid osmotic pressure difference across the microvessels are carefully controlled. Measurements of hydraulic conductivity first using a control perfusate, then after re-cannulation of the same microvessel with the test perfusates enable paired comparisons of the microvessel response under these well-controlled conditions. Attempts to extend the method to microvessels in the mesentery of mice with genetic modifications expected to modify vascular permeability were severely limited because of the absence of long straight and unbranched microvessels in the mouse mesentery, but the recent availability of the rats with similar genetic modifications using the CRISPR/Cas9 technology is expected to open new areas of investigation where the methods described herein can be applied.

The modified Landis technique enables paired measurement of the hydraulic conductivity of individual microvessels in the mesentery of normal and genetically modified rats under control and test conditions using microperfusion techniques. It provides a convenient method to evaluate mechanisms that regulate microvessel permeability and transvascular exchange under physiological conditions.

Experiments to measure the permeability properties of individually perfused microvessels provide a bridge between investigation of molecular and cellular ...

Biology

Constructing and Operating a Cooling Stage to Immobilize C. elegans En Masse

Assembly and Operation of a Cooling Stage to Immobilize C. elegans on Their Culture Plates

High-resolution in vivo microscopy approaches can reveal subtle information and fine details inside the model animal Caenorhabditis elegans (C. elegans), but require strong animal immobilization to prevent motion blur in the images. Unfortunately, most current immobilization techniques require substantial manual effort, rendering high-resolution imaging low-throughput. Immobilization of C. elegans is greatly simplified by using a cooling approach that can easily immobilize entire populations directly on their cultivation plates. The cooling stage can establish and maintain a wide range of temperatures with a uniform distribution on the cultivation plate. In this article, the whole process of building the cooling stage is documented. The aim is that a typical researcher can build an operational cooling stage in their laboratory following this protocol without difficulty. Utilization of the cooling stage following three protocols is shown, and each protocol has advantages for different experiments. Also shown is an example cooling profile of the stage as it approaches its final temperature and some helpful tips in using cooling immobilization.

Author Spotlight: Assembly and Operation of a Cooling Stage to Immobilize C. elegans on Their Culture Plates  

This paper describes protocols for constructing and operating a cooling stage to immobilize C. elegans on their original cultivation plates en masse.

High-resolution in vivo microscopy approaches can reveal subtle information and fine details inside the model animal Caenorhabditis elegans (C. elegans), ...

Fabrication of Microscope Stage for Vertical Observation with Temperature Control Function

Samenvatting

Meer video's verkennen