a-3d-printed-chamber-for-organic-optoelectronic-device-degradation

A 3D-printed Chamber for Organic Optoelectronic Device Degradation Testing

In this manuscript, we outline the manufacture of a small, portable, easy-to-use atmospheric chamber for organic and perovskite optoelectronic devices, ...

McMaster University

Self-assembly of planar molecules can be a critical route to control morphology in organic optoelectronic systems. In this study, Monte Carlo simulations were performed with polygonal disc analogues to planar semiconducting molecules under confinement. By examining statistically the molecular density and configurations of such analogues, we have observed that the symmetry of the confining medium can have a greater impact on the final densified particle configurations than the intramolecular interactions. Using the steric frustration imparted by confinement, novel self-assembled (partially) ordered phases are available. Our Monte Carlo simulations suggest new avenues to control ordering and morphology of planar molecules, which are critical for high-performance organic optoelectronic devices. 

Steric self-assembly of laterally confined organic semiconductor molecule analogues.

High temperature deposition of graphene on Cu by chemical vapor deposition can be used to produce high quality films. However, these films tend to have a non-equilibrium structure, with relatively low graphene adhesion. In this study, samples of graphene grown on copper foils by high temperature CVD were post-deposition annealed at temperatures well below the critical temperature of Cu. Resistance to etching under plasma was examined to assess the mechanical robustness of the graphene on the Cu surface, analyzed using optical and Raman microscopies. We found a correlation between the post-annealing time and etching time for the complete removal of graphene from Cu. Etching rates, minimum etch times, and surface appearance were observed to vary depending on the etching plasma (air, oxygen or nitrogen). Oxygen plasmas were found to be the least aggressive, emphasizing the improved adhesion with post-annealing treatments. Our results imply that the etching of graphene on Cu, and hence the adhesion of graphene, can be controlled by proper annealing and choice of plasma gas. 

Effect of post-annealing on the plasma etching of graphene-coated-copper.

Here we present the fabrication of polypyrrole (PPy) surfaces with a controlled overhang structure. Regularly structured PPy films were produced using interfacial polymerization around a sacrificial crystalline colloidal monolayer at the air/water interface. The morphology of the final inverse colloidal PPy film is controlled by the amount of monomer, the monomer: oxidant ratio and polymerization time. The PPy films exhibit an overhang structure due to depth of particle immersion in the water phase. As a result of the overhang structure, the PPy films are made hydrophobic, although the material itself is hydrophilic. The apparent contact angle of water on the structured surfaces is 109.5°, which is in agreement with the predicted contact angle using the Cassie-Baxter equation for air-filled cavities. This fabrication technique is scalable and can be readily extended to other systems where controlled wettability is required. 

Controlled Fabrication of Polypyrrole Surfaces with Overhang Structures by Colloidal Templating.

Order classification is particularly important in photonics, optoelectronics, nanotechnology, biology, and biomedicine, as self-assembled and living systems tend to be ordered well but not perfectly. Engineering sets of experimental protocols that can accurately reproduce specific desired patterns can be a challenge when (dis)ordered outcomes look visually similar. Robust comparisons between similar samples, especially with limited data sets, need a finely tuned ensemble of accurate analysis tools. Here we introduce our numerical Mathematica package disLocate, a suite of tools to rapidly quantify the spatial structure of a two-dimensional dispersion of objects. The full range of tools available in disLocate give different insights into the quality and type of order present in a given dispersion, accessing the translational, orientational and entropic order. The utility of this package allows for researchers to extract the variation and confidence range within finite sets of data (single images) using different structure metrics to quantify local variation in disorder. Containing all metrics within one package allows for researchers to easily and rapidly extract many different parameters simultaneously, allowing robust conclusions to be drawn on the order of a given system. Quantifying the experimental trends which produce desired morphologies enables engineering of novel methods to direct self-assembly.

disLocate: tools to rapidly quantify local intermolecular structure to assess two-dimensional order in self-assembled systems.

A correction to this article has been published and is linked from the HTML and PDF versions of this paper. The error has been fixed in the paper.

Ayse Turak

Department of Engineering Physics

McMaster University

A 3D-printed Chamber for Organic Optoelectronic Device Degradation Testing

Ayse Turak

.css-o250i3{font-size:18px;font-family:Open Sans,sans-serif;line-height:21.6px;}Department of Engineering Physics

McMaster University

A 3D-printed Chamber for Organic Optoelectronic Device Degradation Testing

Department of Engineering Physics