a-zebrafish-embryo-model-for-vivo-visualization-intravital-analysis

A Zebrafish Embryo Model for In Vivo Visualization and Intravital Analysis of Biomaterial-associated <em>Staphylococcus aureus</em> Infection

Biomaterial-associated infection (BAI) is a major cause of the failure of biomaterials/medical devices. Staphylococcus aureus is one of the major ...

University of Twente

University of Groningen

Meniscus tears are one of the most commonly occurring injuries of the knee joint. Current meniscus repair techniques are challenging and do not bring fully satisfactory results. Tissue adhesives are a promising alternative, since they are easy to apply and cause minimal tissue trauma. In this study, a series of amphiphilic copolymers based on polyethylene glycol, trimethylene carbonate and citric acid were synthesized and subsequently end-functionalized with hexamethylene diisocyanate to form reactive adhesive materials. The shear adhesive strength of the networks to bovine meniscus tissue measured in a lap-shear adhesion test ranged between 20 and 80 kPa, which was better than for fibrin glue (10 kPa). The elastic modulus of the networks depended on composition and was in the same range as that of human meniscus. Cell compatibility was assessed using Alamar Blue staining after incubation of the bovine meniscus cells with different concentrations of the glues for 7 days. Cell viability was not affected after adding up to 3mg of the adhesive/mL of medium. The proposed materials are suitable candidates to be used as resorbable tissue adhesives for meniscus repair. They have excellent mechanical and adhesive properties that can be adjusted by varying the composition of the copolymers.

Development of biodegradable hyper-branched tissue adhesives for the repair of meniscus tears.

The use of ceramic materials in repair of bone defects is limited to non-load-bearing sites. We tested poly(trimethylene carbonate) (PTMC) combined with β-tricalcium phosphate or biphasic calcium phosphate particles for reconstruction of cranial defects.

Poly(trimethylene carbonate)-based composite materials for reconstruction of critical-sized cranial bone defects in sheep.

Novel tough hydrogel materials are required for 3D-printing applications. Here, a series of thermoplastic polyurethanes (TPUs) based on poly(ɛ-caprolactone)--poly(ethylene glycol)--poly(ɛ-caprolactone) (PCL--PEG--PCL) triblock copolymers and hexamethylene diisocyanate (HDI) were developed with PEG contents varying between 30 and 70 mol%. These showed excellent mechanical properties not only when dry, but also when hydrated: TPUs prepared from PCL--PEG--PCL with PEG of Mn 6 kg/mol (PCL₇-PEG₆-PCL₇) took up 122 wt.% upon hydration and had an E-modulus of 52 ± 10 MPa, a tensile strength of 17 ± 2 MPa, and a strain at break of 1553 ± 155% in the hydrated state. They had a fracture energy of 17976 ± 3011 N/mm² and a high tearing energy of 72 kJ/m². TPUs prepared using PEG with Mn of 10 kg/mol (PCL₅-PEG-PCL₅) took up 534% water and were more flexible. When wet, they had an E-modulus of 7 ± 2 MPa, a tensile strength of 4 ± 1 MPa, and a strain at break of 147 ± 41%. These hydrogels had a fracture energy of 513 ± 267 N/mm² and a tearing energy of 16 kJ/m². The latter TPU was first extruded into filaments and then processed into designed porous hydrogel structures by 3D-printing. These hydrogels can be used in 3D printing of tissue engineering scaffolds with high fracture toughness.

Dirk W. Grijpma

Technical Medical Center,
Department of Biomaterials Science and Technology,
Technical Medical Center, Department of Biomaterials Science and Technology

University of Twente

A Zebrafish Embryo Model for In Vivo Visualization and Intravital Analysis of Biomaterial-associated Staphylococcus aureus Infection

Dirk W. Grijpma

.css-o250i3{font-size:18px;font-family:Open Sans,sans-serif;line-height:21.6px;}Technical Medical Center,Department of Biomaterials Science and Technology,Technical Medical Center, Department of Biomaterials Science and Technology

University of Twente

A Zebrafish Embryo Model for In Vivo Visualization and Intravital Analysis of Biomaterial-associated Staphylococcus aureus Infection

Technical Medical Center,
Department of Biomaterials Science and Technology,
Technical Medical Center, Department of Biomaterials Science and Technology