Name: frequency mixing magnetic detection scanner for imaging magnetic particles in planar samples
Uploaded: 2016-06-09T14:00:00.000+00:00
Duration: 7 min 1 s
Description: Watch this Scientific Journal Video about Frequency Mixing Magnetic Detection Scanner for Imaging Magnetic Particles in Planar Samples at JoVE.com

This work was supported by the ICT R&#38;D program of MSIP/IITP, Republic of Korea (Grant No: B0132-15-1001, Development of Next Imaging System).

1. Design a Planar FMMD Measurement Head
<ol>
	<li>Choose a coil scheme for the measurement head. Select a configuration according to Figure 1, consisting of two pickup coils above and two below the sample in a (-, +, +, -) sequence, with the sample sitting in the center between the two (+) coils. The sign denotes the direction of winding, i.e., (+) for clockwise and (-) for counterclockwise. Thus, the sensitivity of the pickup coils becomes almost homogeneous across the sample thickness.
	<ol>
		<li>Place the excitation coils such that the directly induced signal in the pickup coils cancels out in order to prevent saturation of the preamplifier and achieve maximum sensitivity to the sample. Other configurations that fulfill these basic design rules can be devised.</li>
	</ol>
	</li>
	<li>Specify the maximum sample thickness. Here, use 2 mm.
	<ol>
		<li>Choose the diameter and length of the pickup coils similar to the maximum sample thickness. Here, an inner diameter of 2 mm was chosen, which yields an average diameter of 3.7 mm for the height of windings of 1.7 mm. The coil width is 4 mm.</li>
		<li>Choose the wire diameter and the number of windings of the pickup coils such that the total impedance of all pickup coils approximately matches the input impedance of the preamplifier. This condition imposes restrictions on the detection frequency. In the case of a operational amplifier with an optimum input impedance of 1,100 &#937;, all four pickup coils have 600 windings of 0.08 mm dia. enameled copper wire, yielding a total Ohmic series resistance of 95.3 &#937; and a total inductance of 1.9 mH, which gives 919 &#937; impedance.</li>
	</ol>
	</li>
	<li>Prepare the high frequency excitation coils17 such that the magnetic field at the sample&#39;s location ideally amounts to about 0.5 mT. For instance, if the inner radius of the coil is 3.8 mm and the width is 8.5 mm, wind 476 windings of 0.1 mm diameter wire. Here, a field of 0.4 mT was achieved at f1 = 76,550 Hz.</li>
	<li>Prepare the low frequency excitation coils17 such that the magnetic field at the sample&#39;s location is about 5 mT. For instance, if the inner radius of the coil is 5 mm and the width is 8.5 mm, wind 2,000 windings of 0.12 mm diameter wire. The setup yielded 5 mT at f2 = 61 Hz.</li>
</ol>
<img alt="Figure 1" src="/files/ftp_upload/53869/53869fig1.jpg" /> 
Figure 1. Schematic drawing of the p-FMMD set-up. Two measurement heads are electronically connected to each other. The sample is placed in the space between the heads. Detection coils (+) measure the sample signal, counter-wound detection coils (-) serve as reference to cancel out the direct field from the high frequency excitation coils. Amp - preamplifier, x - mixer, LPF - low pass filter, DAQ - data acquisition. <a href="https://www.jove.com/files/ftp_upload/53869/53869fig1large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
2. Construct the Measurement Head
<ol>
	<li>Construct the p-FMMD such that two sets of excitation and detection coils are attached above and below the sample. Each set of coils consists of a low frequency driver coil, a high frequency excitation coil, and a differential detection coil comprising two oppositely wound pickup coils in axial gradiometer configuration.
	<ol>
		<li>Allow for an adjustability of at least one excitation coil relative to the differential detection coil in order to be able to balance out direct induction of the high frequency excitation into the detection coil. For instance, mount the excitation coil on a thread which allows relative movement of the excitation coil versus the detection coil. A schematic diagram of the p-FMMD is shown in Figure 1. Figure 2 depicts a technical drawing and a photograph of the setup. Detailed parameters of the coils are listed in Table 1.</li>
	</ol>
	</li>
	<li>Mount the coil sets above and below the sample on a rigid support, with coaxial orientation, see Figures 1 and 2. Make sure that the two coil sets do not vibrate relative to each other.</li>
	<li>Adjust the high frequency balance of the measurement head by applying the high frequency excitation current to the respective excitation coil set, varying the relative position between them, and simultaneously measuring the detected signal at this frequency at the detection coil set, using equipment such as an oscilloscope or a lock-in amplifier.
	<ol>
		<li>Adjust the directly induced voltage as low as a few millivolts, i.e., more than 1,000-fold suppression of direct induction. Determine the limit of adjustability by observing the phase shift between excitation current and detected voltage. At the minimum, the induced voltage is 90&#176; phase-shifted as compared to direct induction.</li>
	</ol>
	</li>
</ol>
<img alt="Figure 2" src="/files/ftp_upload/53869/53869fig2.jpg" /> 
Figure 2. Technical drawing and photo of p-FMMD head. Cross-sections along a vertical plane (top left) and a horizontal plane (bottom left) are shown as well as a photograph of the opened measurement head before coil winding. 1 - Aluminum support, 2 - coil former for detection coils, 3 - threaded coil former for excitation coils which can be moved up/down by rotation, 4 - sample support plates, 5 - aluminum lids, 6 - sample stopper support, 7 - stopper in x direction, 8 - stopper in y direction. 6 - 8 are removed for scanning. The size of the p-FMMD head is 77 mm &#215; 68 mm &#215; 29 mm. <a href="https://www.jove.com/files/ftp_upload/53869/53869fig2large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
3. Set up Measurement Electronics
<ol>
	<li>Configure the excitation section, consisting of the two oscillators and power amplifiers for both low frequency driver coil and high frequency excitation coil.
	<ol>
		<li>Set up the low frequency driver section, comprising an oscillator and a power amplifier for the low frequency f2. Calculate the power of the amplifier such that it delivers the required current to produce the field of about 5 mT in the driver coil. Here, use a Direct Digital Synthesis (DDS) chip as programmable oscillator. Employ a high-speed buffer as power amplifier.</li>
		<li>Set up the high frequency excitation section, comprising an oscillator and a power amplifier for the high frequency f1. Set up the power amplifier such that it delivers the required current to produce the field of about 0.5 mT in the excitation coil. Use a DDS chip and a high-speed buffer as oscillator and power amplifier, respectively.</li>
	</ol>
	</li>
	<li>Configure the detection section, consisting of a preamplifier, a first mixer to demodulate from the high frequency f1, an intermediate amplifier and filter, a second mixer to demodulate from twice the low frequency 2&#183;f2, and a final filter and output driver. Alternatively, use two lock-in amplifiers to implement the detection electronics.
	<ol>
		<li>Set up the preamplifier stage. Select the input operational amplifier (OP), considering the impedance of the detection coil and the gain-bandwidth product. Perform the noise optimization procedure, taking into account the specified voltage noise and current noise of the OP, as explained in Ref. 10. Select a high-speed low-noise operational amplifier with an amplification of about 100 in the first stage. The subsequent stage is uncritical, but check that the output signal remains in the voltage range, i.e., not distorted due to overloading. Here, use a low-noise JFET input operational amplifier with 4.3-fold amplification.</li>
		<li>Set up the first demodulation stage, multiplying the amplified signal with the high frequency f1. Use an analog multiplier chip and reference it from a second separate DDS chip in order to realize an adjustable phase for demodulation. Alternatively, use a lock-in amplifier as preamplifier (3.2.1), first demodulator (3.2.2) and high frequency generator (3.1.2).</li>
		<li>Set up the intermediate amplification and filtering stage. Implement a low-pass filter such that the signal frequency at 2&#183;f2 passes undisturbed while the spurious high frequency components at f1 and 2&#183;f1 are efficiently suppressed. Choose a suitable intermediate amplification, for instance by selecting two general-purpose operational amplifiers with a total amplification of about 100.</li>
		<li>Set up the second demodulation stage, multiplying the filtered and amplified signal with twice the low frequency 2&#183;f2. Use an analog multiplier chip and reference it from a fourth separate DDS chip in order to realize an adjustable phase for demodulation. Alternatively, use a lock-in amplifier capable of second harmonic demodulation as intermediate amplifier (3.2.3), second demodulator at second harmonic (3.2.4) and low frequency generator (3.1.1).</li>
		<li>Set up the final amplification and filtering stage. Implement a low-pass filter such that the signal frequency at the scanning frequency passes undisturbed while the spurious high frequency components at 4&#183;f2 are efficiently suppressed. Choose a suitable final amplification, considering the desired output voltage range. Use two general-purpose operational amplifiers with a total amplification of about 10.</li>
	</ol>
	</li>
</ol>
4. Set up 2D Scanner
<ol>
	<li>Mount a 2D scanner so that the motion plane is perpendicular to the coil&#39;s axis.</li>
	<li>Control the 2D scanner and synchronously acquiring the output voltage from the measurement electronics in order to obtain a 2D image of the FMMD signal of the planar sample using a homemade script written in the programming language Python.</li>
</ol>
5. Prepare Sample
<ol>
	<li>Use magnetite particles with diameters of 50 nm and 100 nm and maghemite particles with a diameter of 1 &#181;m of which concentration is 25.0 mg/ml. Wash the solution by dissolving the magnetic particles in water, separating them using a magnet and discarding the water. Repeat the procedure three times. Dilute the magnetic particle solution to one tenth with distilled water.</li>
	<li>Prepare paper pellet samples with 2.0 mm diameter by punching pieces of absorptive blotting paper using a biopsy punch. Soak them in magnetic bead solution of different concentrations for 30 sec and let them dry in air. Here, use concentrations of 0.04, 0.2, 1, 5, and 25 mg/ml of 100 nm sized particles.</li>
	<li>Prepare a sample using a nitrocellulose membrane of size 2.0 mm &#215; 18.0 mm. Soak the membrane with the undiluted 1 &#181;m diameter particle solution. Prepare one sample by soaking the membrane evenly, and another one by making a concentration gradient. Do this by soaking the ends of the membrane in beads solution with different concentration, resulting in the concentration gradient (Figure 5).</li>
	<li>Prepare a sample in a capillary tube of 10 &#181;l volume, outer diameter 400 &#181;m, length 40 mm. Fill the capillary tube with undiluted 50 nm diameter particle solution. Prepare a second microtube with 20x diluted solution (mix 100 &#181;l of undiluted solution with 1.9 ml of water).</li>
</ol>
6. Perform 2D FMMD Scan
<ol>
	<li>Select scanning area according to planar dimensions a &#215; b of the sample. Enter the values in the scanning software.</li>
	<li>Select stepping direction. Usually, the shorter of the two planar dimensions, let us call it b, will be selected as stepping direction because that requires less steps and thus less acceleration and deceleration phases.</li>
	<li>Select scanning speed v, with consideration of signal reduction due to low-pass filtering, see discussion. Adjust the speed to a value between 1 and 7 mm/sec. Enter the value in the scanning software.</li>
	<li>Select stepping distance &#916;b, taking into account that it need not be much smaller than the achievable spatial resolution, and the total scanning time t which will be at least t = a/v&#183;b/&#916;b+1). Enter the stepping distance in the software.</li>
	<li>Mount the sample on the 2D scanner. Fix it on the plastic plate using adhesive tape.</li>
</ol>
<img alt="Figure 3" src="/files/ftp_upload/53869/53869fig3.jpg" /> 
Figure 3. Photo of p-FMMD measurement setup. The sample is affixed with adhesive tape on the plastic carrier moved by the motor stage (left). Then the sample is scanned in the p-FMMD head (right). <a href="https://www.jove.com/files/ftp_upload/53869/53869fig3large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<ol start="6">
	<li>Perform the scan by pressing the start button. The scans of Figures 5 and 6 cover a 20.0 mm (x axis) &#215; 25.0 mm (y axis) region, i.e., six 25 mm long traces were scanned along the y axis, with 4.0 mm steps in x direction, at a stage speed of 1.0 mm/sec. This amounts to a scanning time of about 2 min.</li>
</ol>
<img alt="Figure 4" src="/files/ftp_upload/53869/53869fig4.jpg" /> 
Figure 4. Graphical User Interface of the scanning software. The scan parameters are entered here. The measurement is started by pressing the red button.
7. Image Processing
<ol>
	<li>Convert the raw data to matrix form using a homemade script in python. Log the raw data of the whole scan together with extra values in a 2-column comma-separated values (CSV) format file. The extra column indicates the capturing the corresponding data during the stepping motion. The script segments the raw data column at each change of the extra column value and removes the data segments during stepping motion. It also constructs the resultant matrix by putting the remaining consecutive segments into rows or columns of the matrix and writes the matrix into a CSV format file. 
	Note: p-FMMD images of this study are generated using a python script. The pyplot.contour function and the pyplot.imshow function from the matplotlib library for python are cumulatively used for preparation of the contours and the background colors, respectively.</li>
</ol>

<ol>
	<li>Tseng, P., Judy, J. W., Di Carlo, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Magnetic+nanoparticle-mediated+massively+parallel+mechanical+modulation+of+single-cell+behavior.">Magnetic nanoparticle-mediated massively parallel mechanical modulation of single-cell behavior.</a> Nat meth. 9 (11), 1113-1119 (2012).</li><li>Borgert, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Fundamentals+and+applications+of+magnetic+particle+imaging.">Fundamentals and applications of magnetic particle imaging.</a> J. Cardiovasc. Comput. Tomogr. 6 (3), 149-153 (2012).</li><li>Buzug, T. M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Magnetic+particle+imaging:+introduction+to+imaging+and+hardware+realization.">Magnetic particle imaging: introduction to imaging and hardware realization.</a> Z. Med. Phys. 22 (4), 323-334 (2012).</li><li>Kanger, J. S., Subramaniam, V., van Driel, R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Intracellular+manipulation+of+chromatin+using+magnetic+nanoparticles.">Intracellular manipulation of chromatin using magnetic nanoparticles.</a> Chromosome Res. 16 (3), 511-522 (2008).</li><li>Thanh, N. T. K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Magnetic Nanoparticles: From Fabrication to Clinical Applications. , (2012).</li><li>Saritas, E. U., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Magnetic+Particle+Imaging+(MPI)+for+NMR+and+MRI+researchers.">Magnetic Particle Imaging (MPI) for NMR and MRI researchers.</a> J. Magn. Reson. 229 (4), 116-126 (2012).</li><li>Goodwill, P. W., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=X-space+MPI:+magnetic+nanoparticles+for+safe+medical+imaging.">X-space MPI: magnetic nanoparticles for safe medical imaging.</a> Adv. Mater. 24 (28), 3870-3877 (2012).</li><li>Yim, H., Seo, S., Na, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=MRI+Contrast+Agent-Based+Multifunctional+Materials:+Diagnosis+and+Therapy.">MRI Contrast Agent-Based Multifunctional Materials: Diagnosis and Therapy.</a> J Nanomat. 2011 (2011), (2011).</li><li>Gleich, B., Weizenecker, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Tomographic+imaging+using+the+nonlinear+response+of+magnetic+particles.">Tomographic imaging using the nonlinear response of magnetic particles.</a> Nature. 435 (7046), 1214-1217 (2005).</li><li>Rahmer, J., Weizenecker, J., Gleich, B., Borgert, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Analysis+of+a+3-D+system+function+measured+for+magnetic+particle+imaging.">Analysis of a 3-D system function measured for magnetic particle imaging.</a> IEEE Trans. Med. Imaging. 31 (6), 1289-1299 (2012).</li><li>Goodwill, P. W., Conolly, S. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Multidimensional+x-space+magnetic+particle+imaging.">Multidimensional x-space magnetic particle imaging.</a> IEEE Trans. Med. Imaging. 30 (9), 1581-1590 (2011).</li><li>Goodwill, P. W., Konkle, J. J., Zheng, B., Saritas, E. U., Conolly, S. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Projection+x-space+magnetic+particle+imaging.">Projection x-space magnetic particle imaging.</a> IEEE Trans. Med. Imaging. 31 (5), 1076-1085 (2012).</li><li>Gr&#228;fe, K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+Application+Scenario+for+Single-Sided+Magnetic+Particle+Imaging.">An Application Scenario for Single-Sided Magnetic Particle Imaging.</a> Biomed. Tech. 57, (2012).</li><li>Krause, H. -. J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Magnetic+particle+detection+by+frequency+mixing+for+immunoassay+applications.">Magnetic particle detection by frequency mixing for immunoassay applications.</a> J. Magn. Magn. Mater. 311 (1), 436-444 (2007).</li><li>Meyer, M. H. F., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Francisella+tularensis+detection+using+magnetic+labels+and+a+magnetic+biosensor+based+on+frequency+mixing.">Francisella tularensis detection using magnetic labels and a magnetic biosensor based on frequency mixing.</a> J. Magn. Magn. Mater. 311 (1), 259-263 (2007).</li><li>Finas, D., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Detection+and+distribution+of+superparamagnetic+nanoparticles+in+lymphatic+tissue+in+a+breast+cancer+model+for+magnetic+particle+imaging.">Detection and distribution of superparamagnetic nanoparticles in lymphatic tissue in a breast cancer model for magnetic particle imaging.</a> Biomed. Tech. 57, (2012).</li><li>Hong, H., Lim, J., Choi, C. -. J., Shin, S. -. W., Krause, H. -. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Magnetic+particle+imaging+with+a+planar+frequency+mixing+magnetic+detection+scanner.">Magnetic particle imaging with a planar frequency mixing magnetic detection scanner.</a> Rev. Sci. Instr. 85 (1), 013705 (2014).</li><li>Haegele, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Toward+cardiovascular+interventions+guided+by+magnetic+particle+imaging:+First+instrument+characterization.">Toward cardiovascular interventions guided by magnetic particle imaging: First instrument characterization.</a> Magn. Reson. Med. 69 (6), 1761-1767 (2012).</li><li>Haegele, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Magnetic+particle+imaging:+visualization+of+instruments+for+cardiovascular+intervention.">Magnetic particle imaging: visualization of instruments for cardiovascular intervention.</a> Radiology. 265 (3), 933-938 (2012).</li><li>Goodwill, P. W., Lu, K., Zheng, B., Conolly, S. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+x-space+magnetic+particle+imaging+scanner.">An x-space magnetic particle imaging scanner.</a> Rev. Sci. Instrum. 83 (3), 033708 (2012).</li><li>Lampe, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Fast+reconstruction+in+magnetic+particle+imaging.">Fast reconstruction in magnetic particle imaging.</a> Phys. Med. Biol. 57 (4), 1113-1134 (2012).</li><li>Yim, H., Seo, S., Na, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=MRI+Contrast+Agent-Based+Multifunctional+Materials:+Diagnosis+and+Therapy.">MRI Contrast Agent-Based Multifunctional Materials: Diagnosis and Therapy.</a> J Nanomat. 2011 (2011), (2011).</li></ol>

The authors have nothing to disclose.

The measurement technique utilizes the nonlinearity of the magnetization curve of the superparamagnetic particles. The two-sided measurement head simultaneously applies two magnetic excitation fields of different frequency to the sample, a low frequency (f2) component to drive the particles into magnetic saturation and a high frequency (f1) probe field to measure the nonlinear magnetic response. In particular, both harmonics of the incident fields, m&#183;f1<...

Magnetic nanoparticles (MNP) have found widespread applications in molecular biology and in medicine, i.e., for manipulation of biomolecules and single cells1, for selectively labeling target entities for detection,2, 3 for chromatin modulation,4 and for mRNA isolation and cancer treatment.5 Due to their superparamagnetic properties, they are especially useful for medical imaging. They can serve, for instance, as contrast agents or tracers for Magnetic Resonance Imaging (MRI) or for susceptibility imaging using Superconducting Quantum Interference Device (SQUID) detectors. 2, 6 The superparamagnetic nanoparticles yield a good contrast to the different tissues of the human body which are dia- or paramagnetic.7 Thus, the particles can conveniently be used to acquire medical images of human body parts with relatively good spatial resolution and sensitivity.8
The Magnetic Particle Imaging (MPI) technique introduced by Gleich and Weizenecker9 makes use of the nonlinearity of the particle&#39;s magnetization. At zero or weak magnetic field bias, the response of MNP to an ac excitation of frequency f is strong due to their large susceptibility. In particular, the particle&#39;s nonlinear magnetization gives rise to the generation of harmonics n&#183;f, with n = 2, 3, 4 &#8230; At high magnetic field bias, the harmonic response becomes weak because the particles are magnetically saturated. In the MPI technique, the sample is completely magnetized except for a field-free line (FFL) or a field-free point (FFP). Only particles situated close to this line or point will contribute to the nonlinear response of the sample. With the movement of a FFP and employment of suitable receiver coils, Gleich and Weizenecker acquired MPI images with a spatial resolution of 1 mm.
In order to obtain information on the spatial distribution of MNP, two methods are usually employed, the mechanical movement of the sensor with respect to the sample, or movement of the FFL/FFP by means of electromagnets.2, 3 In the latter case, image reconstruction techniques like harmonic-space MPI3 or X-space MPI10, 11, 12 are required. The spatial resolution of MPI is determined by the convolution properties of excitation and detection coils as well as by the characteristics of the magnetic field gradient. This allows image reconstruction algorithms to obtain an improved resolution over the native resolution, which is determined by size and distance of the pickup coils as well as by the magnetic field distribution governed by Maxwell&#39;s equations.
A MPI scanner is usually comprised of a strong magnet for magnetizing the whole sample, a controllable coil system for steering a FFL or FFP across the sample, a high frequency excitation coil system, and a detection coil system for picking up the nonlinear response from the sample. The FFL/FFP is continuously moved through the sample volume while the harmonic response from this unsaturated sample region is recorded. In order to avoid the problem of fitting the specimen into the scanner, a single-sided MPI scanner has been demonstrated by Gr&#228;fe et al.13, however at the expense of reduced performance. Best results are obtained if the sample is surrounded by the magnets and coils. Because the sample has to be fully magnetized except for the FFL/FFP region, the technique requires relatively large and strong magnets with water cooling, leading to a rather bulky and heavy MPI system.
Our approach is based on frequency mixing at the non-linear magnetization curve of superparamagnetic particles.14 When super-paramagnets are exposed to magnetic fields at two distinct frequencies (f1 and f2), sum frequencies representing a linear combination m&#183;f1 + n&#183;f2 (with integer numbers m, n) are generated. It was shown that the appearance of these components is highly specific to the nonlinearity of the magnetization curve of the particles.15 In other words, when the MNP sample is simultaneously exposed to a driving magnetic field at frequency f2 and a probing field at frequency f1, the particles generate a response field at frequency f1 + 2&#183;f2. This sum frequency would not be existent without the magnetically nonlinear sample, therefore the specificity is extremely high. We called this method &#34;frequency mixing magnetic detection&#34; (FMMD). It has been experimentally verified that the technique yields a dynamic range of more than four orders of magnitude in particle concentration.14
In contrast to typical MPI instrumentation, the planar frequency mixing magnetic detection (p-FMMD) approach does not require to magnetize the sample close to saturation because the generation of the sum frequency component f1 + 2&#183;f2 is maximum at zero static bias field.14 Therefore, the need for strong and bulky magnets is alleviated. In fact, the outer dimensions of the measurement head are only 77 mm &#215; 68 mm &#215; 29 mm. For comparison, MPI setups are typically meter-sized.7 The drawback, however, is that the technique is restricted to planar samples with a maximum thickness of 2 mm in the current setup. The sample has to be scanned relatively to the two-sided measurement head. A re-construction allowing for thicker samples is possible, but has to be traded in for a loss of spatial resolution.
Based on this FMMD technique, we present a special type of MPI detector for planar samples, the so-called &#34;planar frequency mixing magnetic detection&#34; (p-FMMD) scanner. The principle has been recently published.17 In this work, we focus on the methodology of the technique and present protocols how to set up such a scanner and how to perform scans. It has been shown that MPI can be applied for medical diagnostic purposes such as cardiovascular or cancer imaging.16, 18, 19 Therefore we believe that the new MPI scanner can be used for a broad range of potential applications, e.g., for measuring magnetic particle distribution in tissue slices.

<table><tbody><tr><td>Magnetic particles &quot;SiMAG Silanol&quot;</td><td>Chemicell (http://www.chemicell.com)</td><td>1101-5</td><td>Aqueous dispersion of magnetic silica particles, Maghemite, dia. 1&amp;nbsp;&amp;micro;m</td></tr><tr><td>Magnetic nanoparticles &quot;fluidMAG-Amine&quot;</td><td>Chemicell (http://www.chemicell.com)</td><td>4121-5</td><td>Aqueous dispersion of magnetic nanoparticles, Magnetite, dia. 50&amp;nbsp;nm</td></tr><tr><td>Microtube 10 &amp;micro;l</td><td>Hirschmann Laborger&amp;auml;te (http://www.hirschmann-laborgeraete.de/?sc_lang=en)</td><td></td><td>volume 10 &amp;micro;l, outer diameter 400&amp;nbsp;&amp;micro;m, length 40 mm</td></tr><tr><td>Nitrocellulose Membrane Biodyne B</td><td>Thermo Scientific (http://www.thermoscientific.com)</td><td>77016</td><td>Biodyne B Nylon Membrane, 0.45&amp;nbsp;&amp;micro;m, 8&amp;nbsp;cm x 12 cm</td></tr><tr><td>DDS chip AD9834</td><td>Analog Devices (http://www.analog.com)</td><td>AD9834</td><td>20 mW Power, 2.3 V to 5.5 V, 75&amp;nbsp;MHz Complete DDS</td></tr><tr><td>Operational Amplifier AD829</td><td>Analog Devices (http://www.analog.com)</td><td>AD829</td><td>High Speed, Low Noise Video Op Amp</td></tr><tr><td>Analog Multiplier MPY634</td><td>Texas Instruments (http://www.ti.com)</td><td>MPY634</td><td>Wide Bandwidth Precision Analog Multiplier</td></tr><tr><td>High-Speed Buffer BUF634</td><td>Texas Instruments (http://www.ti.com)</td><td>BUF634</td><td>250&amp;nbsp;mA High-Speed Buffer</td></tr><tr><td>Operational Amplifier OPA627</td><td>Texas Instruments (http://www.ti.com)</td><td>OPA627</td><td>Precision High-Speed Difet(R) Operational Amplifiers</td></tr><tr><td>Operational Amplifier TL072</td><td>Texas Instruments (http://www.ti.com)</td><td>TL072</td><td>Dual Low-Noise JFET-Input General-Purpose Operational Amplifier</td></tr><tr><td>Lock-In Amplifier SR830</td><td>Stanford Instruments (http://www.thinksrs.com)</td><td>SR830</td><td>100 kHz DSP lock-in amplifier</td></tr><tr><td>XYZ motorized stage</td><td>Sciencetown, Incheon, Korea (http://mkmsll.en.ec21.com/)</td><td></td><td></td></tr><tr><td>Cleanroom wiper</td><td>Seoul Semitech Co (http://www.seoulsemi.com)</td><td>CF-909</td><td>dimension 2.0 mm &amp;times; 18&amp;nbsp;mm</td></tr></tbody></table>

frequency mixing magnetic detection scanner for imaging magnetic particles in planar samples

The setup of a planar Frequency Mixing Magnetic Detection (p-FMMD) scanner for performing Magnetic Particles Imaging (MPI) of flat samples is presented. It consists of two magnetic measurement heads on both sides of the sample mounted on the legs of a u-shaped support. The sample is locally exposed to a magnetic excitation field consisting of two distinct frequencies, a stronger component at about 77 kHz and a weaker field at 61 Hz. The nonlinear magnetization characteristics of superparamagnetic particles give rise to the generation of intermodulation products. A selected sum-frequency component of the high and low frequency magnetic field incident on the magnetically nonlinear particles is recorded by a demodulation electronics. In contrast to a conventional MPI scanner, p-FMMD does not require the application of a strong magnetic field to the whole sample because mixing of the two frequencies occurs locally. Thus, the lateral dimensions of the sample are just limited by the scanning range and the supports. However, the sample height determines the spatial resolution. In the current setup it is limited to 2 mm. As examples, we present two 20 mm &#215; 25 mm p-FMMD images acquired from samples with 1 &#181;m diameter maghemite particles in silanol matrix and with 50 nm magnetite particles in aminosilane matrix. The results show that the novel MPI scanner can be applied for analysis of thin biological samples and for medical diagnostic purposes.

Figure 5a shows the calculated sensitivity distribution of the inner double-differential detection coil as a function of the coordinates x and y in the sample plane. It was calculated in an inverse approach by determining the superposition of the magnetic fields at all points (x, y) in the central plane generated by all four detection coils. In reverse, this determines the detection coil&#39;s sensitivity to a magnetic moment at each of...

Watch this Scientific Journal Video about Frequency Mixing Magnetic Detection Scanner for Imaging Magnetic Particles in Planar Samples at JoVE.com

Frequency Mixing Magnetic Detection Scanner for Imaging Magnetic Particles in Planar Samples

A scanner for imaging magnetic particles in planar samples was developed using the planar frequency mixing magnetic detection technique. The magnetic intermodulation product response from the nonlinear nonhysteretic magnetization of the particles is recorded upon a two-frequency excitation. It can be used to take 2D images of thin biological samples.

The setup of a planar Frequency Mixing Magnetic Detection (p-FMMD) scanner for performing Magnetic Particles Imaging (MPI) of flat samples is presented. ...

frequency-mixing-magnetic-detection-scanner-for-imaging-magnetic

Research

JoVE Journal

Engineering

9.6K Views.  Electronics & Telecommunication Research Institute (ETRI). A scanner for imaging magnetic particles in planar samples was developed using the planar frequency mixing magnetic detection technique. The magnetic intermodulation product response from the nonlinear nonhysteretic magnetization of the particles is recorded upon a two-frequency excitation. It can be used to take 2D images of thin biological samples.

Video: Frequency Mixing Magnetic Detection Scanner for Imaging Magnetic Particles in Planar Samples

Registered Bioimaging of Nanomaterials for Diagnostic and Therapeutic Monitoring 

Nanomedications can be carried by blood borne monocyte-macrophages into the reticuloendothelial system (RES; spleen, liver, lymph nodes) and to end organs. The latter include the lung, RES, and brain and are operative during human immunodeficiency virus type one (HIV-1) infection. Macrophage entry into tissues is notable in areas of active HIV-1 replication and sites of inflammation. In order to assess the potential of macrophages as nanocarriers, superparamagnetic iron-oxide and/or drug laden particles coated with surfactants were parenterally injected into HIV-1 encephalitic mice. This was done to quantitatively assess particle and drug biodistribution. Magnetic resonance imaging (MRI) test results were validated by histological coregistration and enhanced image processing. End organ disease as typified by altered brain histology were assessed by MRI. The demonstration of robust migration of nanoformulations into areas of focal encephalitis provides '"proof of concept" for the use of advanced bioimaging techniques to monitor macrophage migration. Importantly, histopathological aberrations in brain correlate with bioimaging parameters making the general utility of MRI in studies of cell distribution in disease feasible. We posit that using such methods can provide a real time index of disease burden and therapeutic efficacy with translational potential to humans.

Registered Bioimaging of Nanomaterials for Diagnostic and Therapeutic Monitoring

Bioimaging methods used to assess cell biodistribution of nanoparticles are applicable for therapeutic and diagnostic monitoring of nanoformulated compounds. The methods described herein are sensitive and specific when assessed by histological coregistration. The methodologies provide a translational pathway from rodent to human applications.

Nanomedications can be carried by blood borne monocyte-macrophages into the reticuloendothelial system (RES; spleen, liver, lymph nodes) and to end ...

Bioengineering

Remote Magnetic Actuation of Micrometric Probes for in situ 3D Mapping of Bacterial Biofilm Physical Properties

Bacterial adhesion and growth on interfaces lead to the formation of three-dimensional heterogeneous structures so-called biofilms. The cells dwelling in these structures are held together by physical interactions mediated by a network of extracellular polymeric substances. Bacterial biofilms impact many human activities and the understanding of their properties is crucial for a better control of their development &#8212; maintenance or eradication &#8212; depending on their adverse or beneficial outcome. This paper describes a novel methodology aiming to measure in situ the local physical properties of the biofilm that had been, until now, examined only from a macroscopic and homogeneous material perspective. The experiment described here&#160;involves introducing magnetic particles into a growing biofilm to seed local probes that can be remotely actuated without disturbing the structural properties of the biofilm. Dedicated magnetic tweezers were developed to exert a defined force on each particle embedded in the biofilm. The setup is mounted on the stage of a microscope to enable the&#160;recording of time-lapse images of the particle-pulling period. The particle trajectories are then extracted from the pulling sequence and the local viscoelastic parameters are derived from each particle displacement curve, thereby providing the 3D-spatial distribution of the parameters. Gaining insights into the biofilm mechanical profile is essential from an engineer&#39;s point of view for biofilm control purposes but also from a fundamental perspective to clarify the relationship between the architectural properties and the specific biology of these structures.

Remote Magnetic Actuation of Micrometric Probes for in situ 3D Mapping of Bacterial Biofilm Physical Properties

This paper shows an original methodology based on the remote actuation of magnetic particles seeded in a bacterial biofilm and the development of dedicated magnetic tweezers to measure in situ the local mechanical properties of the complex living material built by micro-organisms at interfaces.

Bacterial adhesion and growth on interfaces lead to the formation of three-dimensional heterogeneous structures so-called biofilms. The cells dwelling in ...

Magnetic Field Mapping using Off-Axis Electron Holography in the Transmission Electron Microscope

Off-axis electron holography is a powerful technique that involves the formation of an interference pattern in a transmission electron microscope (TEM) by overlapping two parts of an electron wave, one of which has passed through a region of interest on a specimen and the other is a reference wave. The resulting off-axis electron hologram can be analyzed digitally to recover the phase difference between the two parts of the electron wave, which can then be interpreted to provide quantitative information about local variations in electrostatic potential and magnetic induction within and around the specimen. Off-axis electron holograms can be recorded while a specimen is subjected to external stimuli such as elevated or reduced temperature, voltage, or light. The protocol that is presented here describes the practical steps that are required to record, analyze, and interpret off-axis electron holograms, with a primary focus on the measurement of magnetic fields within and around nanoscale materials and devices. Presented here are the steps involved in the recording, analysis, and processing of off-axis electron holograms, as well as the reconstruction and interpretation of phase images and visualization of the results. Also discussed are the need for optimization of the specimen geometry, the electron optical configuration of the microscope, and the electron hologram acquisition parameters, as well as the need for the use of information from multiple holograms to extract the desired magnetic contributions from the recorded signal. The steps are illustrated through a study of specimens of B20-type FeGe, which contain magnetic skyrmions and were prepared with focused ion beams (FIBs). Prospects for the future development of the technique are discussed.

Guidelines are presented for recording and interpreting off-axis electron holograms to provide quantitative images of magnetic fields in nanoscale materials and devices in the transmission electron microscope.

Off-axis electron holography is a powerful technique that involves the formation of an interference pattern in a transmission electron microscope (TEM) by ...

High-Temperature and High-Pressure In situ Magic Angle Spinning Nuclear Magnetic Resonance Spectroscopy

Nuclear magnetic resonance (NMR) spectroscopy represents an important technique to understand the structure and bonding environments of molecules. There exists a drive to characterize materials under conditions relevant to the chemical process of interest. To address this, in situ high-temperature, high-pressure MAS NMR methods have been developed to enable the observation of chemical interactions over a range of pressures (vacuum to several hundred bar) and temperatures (well below 0 &#176;C to 250 &#176;C). Further, the chemical identity of the samples can be comprised of solids, liquids, and gases or mixtures of the three. The method incorporates all-zirconia NMR rotors (sample holder for MAS NMR) which can be sealed using a threaded cap to compress an O-ring. This rotor exhibits great chemical resistance, temperature compatibility, low NMR background, and can withstand high pressures. These combined factors enable it to be utilized in a wide range of system combinations, which in turn permit its use in diverse fields as carbon sequestration, catalysis, material science, geochemistry, and biology. The flexibility of this technique makes it an attractive option for scientists from numerous disciplines.

The molecular structures and dynamics of solids, liquids, gases, and mixtures are of critical interest to diverse scientific fields. High-temperature, high-pressure in situ MAS NMR enables detection of the chemical environment of constituents in mixed phase systems under tightly controlled chemical environments.

Nuclear magnetic resonance (NMR) spectroscopy represents an important technique to understand the structure and bonding environments of molecules. There ...

Chemistry

Magnetic Levitation Coupled with Portable Imaging and Analysis for Disease Diagnostics

Currently, many clinical diagnostic procedures are complex, costly, inefficient, and inaccessible to a large population in the world. The requirements for specialized equipment and trained personnel require that many diagnostic tests be performed at remote, centralized clinical laboratories. Magnetic levitation is a simple yet powerful technique and can be applied to levitate cells, which are suspended in a paramagnetic solution and placed in a magnetic field, at a position determined by equilibrium between a magnetic force and a buoyancy force. Here, we present a versatile platform technology designed for point-of-care diagnostics which uses magnetic levitation coupled to microscopic imaging and automated analysis to determine the density distribution of a patient's cells as a useful diagnostic indicator. We present two platforms operating on this principle: (i) a smartphone-compatible version of the technology, where the built-in smartphone camera is used to image cells in the magnetic field and a smartphone application processes the images and to measures the density distribution of the cells and (ii) a self-contained version where a camera board is used to capture images and an embedded processing unit with attached thin-film-transistor (TFT) screen measures and displays the results. Demonstrated applications include: (i) measuring the altered distribution of a cell population with a disease phenotype compared to a healthy phenotype, which is applied to sickle cell disease diagnosis, and (ii) separation of different cell types based on their characteristic densities, which is applied to separate white blood cells from red blood cells for white blood cell cytometry. These applications, as well as future extensions of the essential density-based measurements enabled by this portable, user-friendly platform technology, will significantly enhance disease diagnostic capabilities at the point of care.

We present a magnetic levitation technique coupled with automated imaging and analysis in both a smartphone-compatible device and a device with embedded imaging and processing. This is applied to measure the density distribution of cells with two demonstrated biomedical applications: sickle cell disease diagnosis and separating white and red blood cells.

Currently, many clinical diagnostic procedures are complex, costly, inefficient, and inaccessible to a large population in the world. The requirements for ...

Rapid Homogeneous Detection of Biological Assays Using Magnetic Modulation Biosensing System

A magnetic modulation biosensing system (MMB) [1,2] rapidly and homogeneously detected biological targets at low concentrations without any washing or separation step. When the IL-8 target was present, a 'sandwich'-based assay attached magnetic beads with IL-8 capture antibody to streptavidin coupled fluorescent protein via the IL-8 target and a biotinylated IL-8 antibody. The magnetic beads are maneuvered into oscillatory motion by applying an alternating magnetic field gradient through two electromagnetic poles. The fluorescent proteins, which are attached to the magnetic beads are condensed into the detection area and their movement in and out of an orthogonal laser beam produces a periodic fluorescent signal that is demodulated using synchronous detection. The magnetic modulation biosensing system was previously used to detect the coding sequences of the non-structural Ibaraki virus protein 3 (NS3) complementary DNA (cDNA) [2]. The techniques that are demonstrated in this work for external manipulation and condensation of particles may be used for other applications, e.g. delivery of magnetically-coupled drugs in-vivo or enhancing the contrast for in-vivo imaging applications.

Magnetic modulation biosensing system is utilized to rapidly, sensitively and simply detect biological assays, such as DNA molecules and proteins.

A magnetic modulation biosensing system (MMB) [1,2] rapidly and homogeneously detected biological targets at low concentrations without any washing or ...

Biology

Optimizing Magnetic Force Microscopy Resolution and Sensitivity to Visualize Nanoscale Magnetic Domains

Magnetic force microscopy (MFM) enables mapping local magnetic fields across a sample surface with nanoscale resolution. To perform MFM, an atomic force microscopy (AFM) probe whose tip has been magnetized vertically (i.e., perpendicular to the probe cantilever) is oscillated at a fixed height above the sample surface. The resultant shifts in the oscillation phase or frequency, which are proportional to the magnitude and sign of the vertical magnetic force gradient at each pixel location, are then tracked and mapped. Although the spatial resolution and sensitivity of the technique increases with decreasing lift height above the surface, this seemingly straightforward path to improved MFM images is complicated by considerations such as minimizing topographical artifacts due to shorter range van der Waals forces, increasing the oscillation amplitude to further improve sensitivity, and the presence of surface contaminants (in particular water due to humidity under ambient conditions). In addition, due to the orientation of the probe's magnetic dipole moment, MFM is intrinsically more sensitive to samples with an out-of-plane magnetization vector. Here, high-resolution topographical and magnetic phase images of single and bicomponent nanomagnet artificial spin-ice (ASI) arrays obtained in an inert (argon) atmosphere glovebox with &lt;0.1 ppm O2 and H2O are reported. Optimization of lift height and drive amplitude for high resolution and sensitivity while simultaneously avoiding the introduction of topographical artifacts is discussed, and detection of the stray magnetic fields emanating from either end of the nanoscale bar magnets (~250 nm long and &lt;100 nm wide) aligned in the plane of the ASI sample surface is shown. Likewise, using the example of a Ni-Mn-Ga magnetic shape memory alloy (MSMA), MFM is demonstrated in an inert atmosphere with magnetic phase sensitivity capable of resolving a series of adjacent magnetic domains each ~200 nm wide.

Magnetic force microscopy (MFM) employs a vertically magnetized atomic force microscopy probe to measure sample topography and local magnetic field strength with nanoscale resolution. Optimizing MFM spatial resolution and sensitivity requires balancing decreasing lift height against increasing drive (oscillation) amplitude, and benefits from operating in an inert atmosphere glovebox.

Magnetic force microscopy (MFM) enables mapping local magnetic fields across a sample surface with nanoscale resolution. To perform MFM, an atomic force ...

Quantifying Mixing using Magnetic Resonance Imaging

Mixing is a unit operation that combines two or more components into a homogeneous mixture. This work involves mixing two viscous liquid streams using an in-line static mixer. The mixer is a split-and-recombine design that employs shear and extensional flow to increase the interfacial contact between the components. A prototype split-and-recombine (SAR) mixer was constructed by aligning a series of thin laser-cut Poly (methyl methacrylate) (PMMA) plates held in place in a PVC pipe. Mixing in this device is illustrated in the photograph in Fig. 1. Red dye was added to a portion of the test fluid and used as the minor component being mixed into the major (undyed) component. At the inlet of the mixer, the injected layer of tracer fluid is split into two layers as it flows through the mixing section. On each subsequent mixing section, the number of horizontal layers is duplicated. Ultimately, the single stream of dye is uniformly dispersed throughout the cross section of the device.
 Using a non-Newtonian test fluid of 0.2% Carbopol and a doped tracer fluid of similar composition, mixing in the unit is visualized using magnetic resonance imaging (MRI). MRI is a very powerful experimental probe of molecular chemical and physical environment as well as sample structure on the length scales from microns to centimeters. This sensitivity has resulted in broad application of these techniques to characterize physical, chemical and/or biological properties of materials ranging from humans to foods to porous media 1, 2. The equipment and conditions used here are suitable for imaging liquids containing substantial amounts of NMR mobile 1H such as ordinary water and organic liquids including oils. Traditionally MRI has utilized super conducting magnets which are not suitable for industrial environments and not portable within a laboratory (Fig. 2). Recent advances in magnet technology have permitted the construction of large volume industrially compatible magnets suitable for imaging process flows. Here, MRI provides spatially resolved component concentrations at different axial locations during the mixing process. This work documents real-time mixing of highly viscous fluids via distributive mixing with an application to personal care products.

Magnetic resonance imaging (MRI) provides a powerful tool to evaluate the effectiveness of process equipment during operation. We discuss the use of MRI to visualize mixing in a static mixer. The application is relevant to personal care products, but can be applied to a broad range of food, chemical, biomass and biological fluids.

Mixing is a unit operation that combines two or more components into a homogeneous mixture.  This work involves mixing two viscous liquid streams using an ...

Fabrication of Magnetic Platforms for Micron-Scale Organization of Interconnected Neurons

The ability to direct neurons into organized neural networks has great implications for regenerative medicine, tissue engineering, and bio-interfacing. Many studies have aimed at directing neurons using chemical and topographical cues. However, reports of organizational control on a micron-scale over large areas are scarce. Here, an effective method has been described for placing neurons in preset sites and guiding neuronal outgrowth with micron-scale resolution, using magnetic platforms embedded with micro-patterned, magnetic elements. It has been demonstrated that loading neurons with magnetic nanoparticles (MNPs) converts them into sensitive magnetic units that can be influenced by magnetic gradients. Following this approach, a unique magnetic platform has been fabricated on which PC12 cells, a common neuron-like model, were plated and loaded with superparamagnetic nanoparticles. Thin films of ferromagnetic (FM) multilayers with stable perpendicular magnetization were deposited to provide effective attraction forces toward the magnetic patterns. These MNP-loaded PC12 cells, plated and differentiated atop the magnetic platforms, were preferentially attached to the magnetic patterns, and the neurite outgrowth was well aligned with the pattern shape, forming oriented networks. Quantitative characterization methods of the magnetic properties, cellular MNP uptake, cell viability, and statistical analysis of the results are presented. This approach enables the control of neural network formation and improves neuron-to-electrode interface through the manipulation of magnetic forces, which can be an effective tool for in vitro studies of networks and may offer novel therapeutic biointerfacing directions.

This work presents a bottom-up approach to the engineering of local magnetic forces for control of neuronal organization. Neuron-like cells loaded with magnetic nanoparticles (MNPs) are plated atop and controlled by a micro-patterned platform with perpendicular magnetization. Also described are magnetic characterization, MNP cellular uptake, cell viability, and statistical analysis.

The ability to direct neurons into organized neural networks has great implications for regenerative medicine, tissue engineering, and bio-interfacing. ...

A Magnetic Nanoparticle-Based Immunoassay Using a Microfluidic Device

Source: Hern&#225;ndez-Ortiz, J. A., et al. <a href="https://app.jove.com/v/63899">Computer Numerical Control Micromilling of a Microfluidic Acrylic Device with a Staggered Restriction for Magnetic Nanoparticle-Based Immunoassays.</a> J. Vis. Exp. (2022).
This video demonstrates a microfluidic system for a magnetic nanoparticle-based immunoassay. The detection system utilizes a microfluidic device incorporating a magnetic trap within its channels. Pre-formed immunocomplexes, comprised of antigen-coated magnetic nanoparticles bound to primary and peroxidase-conjugated secondary antibodies, are introduced into the channels. The immunocomplexes become captured in the porous magnetic trap upon applying an external magnetic field. Using a fluorogenic substrate emitting fluorescence upon catalysis by the peroxidases, the captured immunocomplexes are detected under a microscope.

Test immunologiczny oparty na nanocząstkach magnetycznych przy użyciu urządzenia mikroprzepływowego

1. Device preparation

	Fill the channels with distilled water using a syringe. Make sure there are no leaks or resistance to flow. Immerse the device in ...

Frequency Mixing Magnetic Detection Scanner for Imaging Magnetic Particles in Planar Samples

Podsumowanie

Przeglądaj więcej filmów

Rozdziały w tym wideo

Registered Bioimaging of Nanomaterials for Diagnostic and Therapeutic Monitoring

Remote Magnetic Actuation of Micrometric Probes for in situ 3D Mapping of Bacterial Biofilm Physical Properties

Magnetic Field Mapping using Off-Axis Electron Holography in the Transmission Electron Microscope

High-Temperature and High-Pressure In situ Magic Angle Spinning Nuclear Magnetic Resonance Spectroscopy

Magnetic Levitation Coupled with Portable Imaging and Analysis for Disease Diagnostics

Rapid Homogeneous Detection of Biological Assays Using Magnetic Modulation Biosensing System

Optimizing Magnetic Force Microscopy Resolution and Sensitivity to Visualize Nanoscale Magnetic Domains

Quantifying Mixing using Magnetic Resonance Imaging

Fabrication of Magnetic Platforms for Micron-Scale Organization of Interconnected Neurons

Test immunologiczny oparty na nanocząstkach magnetycznych przy użyciu urządzenia mikroprzepływowego