This study was supported by the Slovenian Research Agency (ARRS) Program P4-0015 (Wood and lignocellulosic composites) and the Young Researchers&#39; Program.

1. Inspection and description of a stringed musical instrument&#160;-&#160;violin
NOTE: Violins are the most frequently investigated stringed instruments. Therefore, we describe the procedure on a violin.
<ol>
	<li>Examine the instrument and all its parts. Take detailed photos of the front (top), back, side, scroll, and label along with the measuring scale for the final report and the archive (Figure 1).</li>
	<li>Examine the top plate of the instrument to determine how it is constructed. If possible, remove the strings from the instrument to facilitate the analysis.</li>
	<li>Check whether the top plate is made of one, two, or more parts and how they are joined together. Here, the procedure is described for a top plate made of two parts, which is the most common case.</li>
	<li>On the radial board of the top plate (Figure 2A,C), examine the structure and orientation of the tree rings. They are seen as bands of annual growth layers, consisting of light-colored earlywood and darker latewood and delimited by the tree ring boundaries (Figure 2D).</li>
	<li>Based on the location and transition of earlywood to latewood, determine which side is the bark and which side is the pith (Figure 2C,G). In most cases, the most recently formed tree rings are located at the joint in the center of the top plate (when it consists of two parts; Figure 2C,D,F). These are the rings that were the nearest to the bark when the tree was still growing (Figure 2D,G). 
	NOTE: Since we need to look at the radial structure, the tree rings appear as bands and not rings. Nevertheless, the terms tree rings and tree ring width (TRW) are used in this protocol.</li>
</ol>
2. Selection of the locations for measurements on the musical instrument
<ol>
	<li>Inspect the widest parts on each piece of the top plate.</li>
	<li>Check for any damage, repairs, retouching, or dirt, and where the varnish is transparent enough to see the tree rings. If the instrument is opened (in the case of ongoing repairs or during restoration), measure the tree rings on the underside of the top plate, where no varnish is applied.</li>
	<li>Select the area with the greatest number of tree rings and check if the boundaries between the rings can be recognized (Figure 2C,D). The measurements can only be correct if the wood structure is clearly visible.</li>
	<li>Try to clearly see the tree rings that were near the bark as the tree was growing for an accurate identification of the end date (Figure 2D). Use a magnifying lens or stereo microscope for the observations.</li>
	<li>Mark the measuring line in the direction from the bark to the pith. Equip it with a measuring scale (Figure 2C). Place the scale (for instance, a commercially available paper measuring tape) on the board for this purpose.</li>
</ol>
3. Capturing digital images
<ol>
	<li>Capture images to measure the tree ring width with an image analysis system. Place the violin&#160;top plate side on the scanner and scan the parts selected for the tree ring measurement (Figure 2B). Select a resolution of 1,200 dpi or higher. Use a scanner that allows a high depth of field. 
	NOTE: Scanning is not the only way to capture images. A camera or other equipment can be used as well. If several images have to be captured, they must be stitched together properly. It is also possible to measure the tree ring width directly on the violin with the aid of a microscope and a special measuring device (e.g., a measuring table). This is especially useful in cases of poor visibility of the structure and if observation under a stereo microscope lens is needed. In this case, the images are valuable for further control of the measurements and for the archive.</li>
	<li>For editing the images, use a graphics editing program to check the quality of the image and adjust the color, brightness, and contrast to best see the annual growth rings and the boundaries between them. This step is useful when measuring tree rings with an image analysis system.</li>
	<li>To store the images, save the images in an adequate format (.tiff, .jpg).</li>
</ol>
4. Measurement of tree ring width
<ol>
	<li>Start an image analysis system, preferably one designed for the automatic and manual detection of tree rings and the measurement of TRW.</li>
	<li>Open the image and check or set the calibration manually by measuring the distance of a known length on the measurement scale that is part of the image (Figure 2C,D).</li>
	<li>Start the measurement by clicking on the tree ring boundaries so that the distance between them, representing the TRW, is recorded (Figure 2D). Note whether the first tree ring measured is closer to the bark or closer to the pith. For violins, click the tree ring boundaries manually, because the automatic detection of TRW is usually not possible or requires too many corrections.</li>
	<li>Measure all the TRWs along the measurement line. Save the data as the tree ring series (Figure 2E), with each TRW recorded for a specific relative year. Save the data in one of the widely used data formats. Perform more than one measurement on the same board for later verification. 
	NOTE: There are also other options (not described here) for the TRW measurements. Option 1: Use a general image analysis system, open and calibrate the image, measure the TRW, and note the measurements. Option 2: Using a 10x magnification lens with a built-in metric scale, measure the TRW directly on the violin and record the measurements. Option 3: Use a classic setup of dendrochronological equipment consisting of a movable measuring table, a stereo microscope, and a special program to record the measurement4,15. Place the violin on the table and observe it under a stereo microscope. Start the program for tree ring measurement and measure the TRW by clicking the tree ring boundaries.</li>
</ol>
5. Data processing, cross-dating, and building the chronology of the instrument
NOTE: For cross-dating, a specialized program and suitable reference chronologies are needed.
<ol>
	<li>For data processing, open the data file. We describe here how to use the raw TRW series (i.e., TRWs (in mm) against years; Figure 2E). 
	NOTE: It is also possible to work with indexed data.</li>
	<li>For cross-dating a tree ring series of the same instrument, open the tree ring series to be cross-dated and another tree ring series of the same instrument to serve as a reference and run the cross-dating, which moves them into the synchronous (cross-dated) position.</li>
	<li>Check the tree ring patterns and the cross-dating parameters. If the measurement is correct, the tree ring patterns, especially those of the same board, are very similar (Figure 2E), and the cross-dating parameters are high.
	<ol>
		<li>Check for the following main cross-dating parameters used in studies of violins: the concordance coefficient Gleichl&#228;ufigkeit (Glk%), the Baillie and Pilcher t-value (TVBP), and the Hollstein t-value (TVH)20,21,22.</li>
		<li>Consider the parameters statistically significant if Glk &#8805;65%, TVBP &#8805;4.0, TVH &#8805;4.0. In the case of dating musical instruments, keep the criteria stricter and parameter values higher (e.g., TVBP &#8805;7.0).</li>
		<li>Consider the overlap (OVL), which indicates the overlapping period of two tree ring series, in years as well.</li>
	</ol>
	</li>
	<li>When the two tree ring series are on the same relative time scale, save the position of the series. Repeat this step until all the tree ring series of each board and instrument are cross-dated. 
	NOTE: The cross-dating is based on the comparison of (two) tree ring series by calculating the statistical similarity parameters and graphical comparison (matching) of the graphs. A good agreement between the tree ring series (of the same instrument) confirms the correctness of the measurement, which is compromised if the tree rings are very narrow or indistinct or if they are missing (i.e., did not form in a tree).</li>
	<li>For creating the chronology of the violin, when all the TRW series of the same board and instrument are cross-dated, look at their graphs. Then, select those that have no measurement errors and average them to form a chronology of the instrument. At this stage, the chronology is not yet dated.
	<ol>
		<li>For this purpose, produce at least two measurements from each part of the top plate. If the agreement between the series within the instrument is statistically significant, average all the tree ring series into one chronology of the instrument.</li>
	</ol>
	</li>
</ol>
6. Dating of the instrument
<ol>
	<li>Cross-date the chronology of the violin with the reference chronologies. Use several reference chronologies in this step. Perform the cross-dating, check the parameters of the agreement, and visually assess the proposed dating position.
	<ol>
		<li>For successful dating, ensure that the same end date is confirmed by multiple chronologies with statistically significant parameters, as well as by optical comparison of the sequences. Use additional techniques such as the formation of average chronologies from matching curves or the segmentation of longer series for additional confirmation of the dating. 
		NOTE: This is a very critical step because one needs proper reference chronologies for dating. Some reference data are available on the ITRDB14.</li>
	</ol>
	</li>
	<li>Report the end date, which is the final result of the dendrochronological analysis23. Estimate the number of years, which should be added to the end date to propose the potential date of manufacture of the instrument. For this purpose, use the information on the label (if original) and other sources about the potential age, geographic area, manufacturer, and organological characteristics of the instrument assessed by other experts.</li>
	<li>Try to confirm the assumptions about the age, maker, and area of origin as this helps to decide if the violin is authentic or not. 
	NOTE: The end date does not indicate the year in which the violin was made, and this must be estimated.</li>
	<li>Write a report that includes the dendrochronological end date and sufficient information about the investigation supported by information that may help in the interpretation of the dating. 
	NOTE: The most important steps of the protocol are illustrated in Figure 2.</li>
</ol>
<img alt="Figure 2" class="xfigimg" src="/files/ftp_upload/64591/64591fig02.jpg" /> 
Figure 2: Detailed representation of the steps of the protocol. (A) A violin with the top plate made of two resonance boards (bass and treble); (B) scanning of the top plate; (C) part selected for the tree ring width (TRW) measurement (precision 0.01 mm) and measurement direction from the bark to the pith (which were outside the board); (D) tree rings as bands on the radial board and the TRW measurement direction from the darker latewood to the light colored earlywood; asterisks indicate where the two boards with end dates of 2003 and 1995 are glued together; +1, +2, +3&#8230; denote the locations of the tree ring boundaries (+) and the tree ring numbers (1, 2, 3); scale bar = 1 cm; (E)&#160;tree-ring series of the treble and bass side of a violin in cross-dated position and end dates 2003 and 1995 indicated; (F) different end dates of the two boards due to different numbers of tree rings being removed during the manufacturing of the instrument; (G) orientation of the resonance board in the tree and the tree rings corresponding to the end date and the last tree ring below the bark formed before the tree was cut. <a href="https://www.jove.com/files/ftp_upload/64591/64591fig02large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>

<ol>
	<li>Klein, P., Mehringer, H., Bauch, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Dendrochronological+and+wood+biological+investigations+on+string+instruments.">Dendrochronological and wood biological investigations on string instruments.</a> Holzforschung. 40 (4), 197-203 (1986).</li><li>Topham, J., McCormick, D. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Dendrochronological+investigation+of+British+stringed+instruments+of+the+violin+family.">Dendrochronological investigation of British stringed instruments of the violin family.</a> Journal of Archaeological Science. 25 (11), 1149-1157 (1998).</li><li>Bernabei, M., Bontadi, J., Rossi Rognoni, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+dendrochronological+investigation+of+stringed+instruments+from+the+collection+of+the+Cherubini+Conservatory+in+Florence,+Italy.">A dendrochronological investigation of stringed instruments from the collection of the Cherubini Conservatory in Florence, Italy.</a> Journal of Archaeological Science. 37 (1), 192-200 (2010).</li><li>Bernabei, M., Bontadi, J., Sisto, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Dendrochronological+analysis+of+bowed+and+plucked+instruments+from+the+San+Pietro+a+Majella+conservatory,+Naples.">Dendrochronological analysis of bowed and plucked instruments from the San Pietro a Majella conservatory, Naples.</a> Archaeometry. , 12808 (2022).</li><li>Cherubini, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Tree-ring+dating+of+musical+instruments;+Dendrochronology+detects+fraudulent+art+but+with+some+caveats.">Tree-ring dating of musical instruments; Dendrochronology detects fraudulent art but with some caveats.</a> Science. 373 (6562), 1434-1436 (2021).</li><li>Cherubini, P., Carlson, B., Talirz, W., Malcolm, H., Wiener, M. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Musical+string+instruments:+Potential+and+limitations+of+tree-ring+dating+and+provenancing+to+verify+their+authenticity.">Musical string instruments: Potential and limitations of tree-ring dating and provenancing to verify their authenticity.</a> Dendrochronologia. 72, 125942 (2022).</li><li>Leonhard, F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=On+a+mysterious+violin+and+the+process+of+authentication.">On a mysterious violin and the process of authentication.</a> Strings Magazine. , (2016).</li><li>Fritts, H. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Tree rings and climate. , (1976).</li><li>Topham, J. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Dendrochronological+study+of+violins+made+by+Antonio+Stradivari.">Dendrochronological study of violins made by Antonio Stradivari.</a> Journal of American Musical Instrument Society. 29, 72-96 (2003).</li><li>Beuting, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Holzkundliche und dendrochronologische Untersuchungen an Resonanzholz als Beitrag zur Organologie. , (2004).</li><li>Ratcliff, P. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Dendrochronology,+an+invaluable+tool+in+the+classification+of+instruments+of+the+violin+family.">Dendrochronology, an invaluable tool in the classification of instruments of the violin family.</a> Multidisciplinary Approach to Wooden Musical Instrument Identification. , (2014).</li><li>Bernabei, M., Bontadi, J., &#268;ufar, K., Baici, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Dendrochronological+investigation+of+the+bowed+string+instruments+at+the+Theatre+Museum+Carlo+Schmidl+in+Trieste,+Italy.">Dendrochronological investigation of the bowed string instruments at the Theatre Museum Carlo Schmidl in Trieste, Italy.</a> Journal of Cultural Heritage. 27, 55-62 (2017).</li><li>Bucur, V. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Acoustics of Wood, second edition. , (2006).</li><li>National Centers for Environmental Information. International Tree Ring Data Bank (ITRDB) Available from: <a target="_blank" href="https://www.ncei.noaa.gov/products/paleoclimatology/tree-ring">https://www.ncei.noaa.gov/products/paleoclimatology/tree-ring</a> (2020)</li><li>Bernabei, M., Bontadi, J., Sisto, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Dendrochronological+analysis+of+the+Stradivari's+harp.">Dendrochronological analysis of the Stradivari's harp.</a> Dendrochronologia. 74, 125960 (2022).</li><li>Bernabei, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+Guarneri+violin+in+the+attic:+The+power+of+dendrochronology+for+analysing+musical+instruments.">A Guarneri violin in the attic: The power of dendrochronology for analysing musical instruments.</a> Heritage Science. 9, 47 (2021).</li><li>Beuting, M., Klein, P., Wein, K. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Dendrochronologische+Untersuchungen+an+Streichinstrumenten+von+Jacob+Stainer.">Dendrochronologische Untersuchungen an Streichinstrumenten von Jacob Stainer.</a> Jacob Stainer: &amp;#34;...kayserlicher Diener und Geigenmacher zu Absom&amp;#34;. , 167-171 (2003).</li><li>Beuting, M., Klein, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Dendrochronologische+Untersuchungen+an+Musikinstrumenten+von+Joachim+Tielke.">Dendrochronologische Untersuchungen an Musikinstrumenten von Joachim Tielke.</a> Hellwig, Friedemann und Barbara: Joachim Tielke. Neue Funde zu Werk und Wirkung. , 32-48 (2020).</li><li>Beuting, M., Fontana, E., Heller, V., Martius, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Dendrochronologische+Untersuchungen+an+Instrumenten+von+Martin+und+Johann+Christian+Hoffmann.">Dendrochronologische Untersuchungen an Instrumenten von Martin und Johann Christian Hoffmann.</a> Martin und Johann Christian Hoffmann. Geigen- und Lautenmacher des Barock. , 266-275 (2015).</li><li>Eckstein, D., Bauch, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Beitrag+zur+Rationalisierung+eines+dendrochronologischen+Verfahrens+und+zur+Analyse+seiner+Aussagesicherheit.">Beitrag zur Rationalisierung eines dendrochronologischen Verfahrens und zur Analyse seiner Aussagesicherheit.</a> Forstwissenschaftliches Centralblatt. 88, 230-250 (1969).</li><li>Baillie, M. G. L., Pilcher, J. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+simple+cross-dating+program+for+tree-ring+research.">A simple cross-dating program for tree-ring research.</a> Tree Ring Bulletin. 33, 7-14 (1973).</li><li>Hollstein, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Mitteleurop&#228;ische+Eichenchronologie.">Mitteleurop&#228;ische Eichenchronologie.</a> Trierer dendrochronologische Forschungen zur Arch&#228;ologie und. , (1980).</li><li>&#268;ufar, K., Beuting, M., Dem&#353;ar, B., Merela, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Dating+of+violins+-+The+interpretation+of+dendrochronological+reports.">Dating of violins - The interpretation of dendrochronological reports.</a> Journal of Cultural Heritage. 27, 44-54 (2017).</li><li>Klein, P., Pollens, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+technique+of+dendrochronology+as+applied+to+violins+made+by+Guiseppe+Guarneri+del+Ges&#249;.">The technique of dendrochronology as applied to violins made by Guiseppe Guarneri del Ges&#249;.</a> Guiseppe Guarneri del Ges&#249;. , 159-161 (1998).</li><li>&#268;ufar, K., Beuting, M., Grabner, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Dendrochronological+dating+of+two+violins+from+private+collections+in+Slovenia.">Dendrochronological dating of two violins from private collections in Slovenia.</a> Zbornik Gozdarstva in Lesarstva. 91, 75-84 (2010).</li><li>Siebenlist Kerner, V. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Der+Aufbau+von+Jahrringchronologien+f&#252;r+Zierbelkiefer,+L&#228;rche+und+Fichte+eines+Alpinen+Hochgebirgsstandortes.">Der Aufbau von Jahrringchronologien f&#252;r Zierbelkiefer, L&#228;rche und Fichte eines Alpinen Hochgebirgsstandortes.</a> Dendrochronologia. 2, 9-29 (1984).</li><li>Bernabei, M., &#268;ufar, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Methods+of+dendrochronology+for+musical+instruments.">Methods of dendrochronology for musical instruments.</a> Wooden Musical Instruments Different Forms of Knowledge: Book of End of WoodMusICK COST Action. , 67-80 (2018).</li><li>Balzano, A., Novak, K., Humar, M., &#268;ufar, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Application+of+confocal+laser+scanning+microscopy+in+dendrochronology.">Application of confocal laser scanning microscopy in dendrochronology.</a> Les/Wood. 68 (2), 5-17 (2019).</li><li>Levani&#269;, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Atrics+-+A+new+system+for+image+acquisition+in+dendrochronology.">Atrics - A new system for image acquisition in dendrochronology.</a> Tree-Ring Research. 63 (2), 117-122 (2009).</li><li>Von Arx, G., Crivellaro, A., Prendin, A. L., &#268;ufar, K., Carrer, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Quantitative+wood+anatomy+-+Practical+guidelines.">Quantitative wood anatomy - Practical guidelines.</a> Frontiers in Plant Science. 7, 781 (2016).</li><li>Sodini, N., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Non-invasive+microstructural+analysis+of+bowed+stringed+instruments+with+synchrotron+radiation+X-ray+microtomography.">Non-invasive microstructural analysis of bowed stringed instruments with synchrotron radiation X-ray microtomography.</a> Journal of Cultural Heritage. 13, 44-49 (2012).</li><li>Sodini, N., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Comparison+of+different+experimental+approaches+in+the+tomographic+analysis+of+ancient+violins.">Comparison of different experimental approaches in the tomographic analysis of ancient violins.</a> Journal of Cultural Heritage. 27, 588-592 (2017).</li><li>Stanciu, M. D., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=X-ray+imaging+and+computed+tomography+for+the+identification+of+geometry+and+construction+elements+in+the+structure+of+old+violins.">X-ray imaging and computed tomography for the identification of geometry and construction elements in the structure of old violins.</a> Materials. 14 (20), 5926 (2021).</li><li>Akhmetzyanov, L., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Towards+a+new+approach+for+dendroprovenancing+pines+in+the+Mediterranean+Iberian+Peninsula.">Towards a new approach for dendroprovenancing pines in the Mediterranean Iberian Peninsula.</a> Dendrochronologia. 60, 125688 (2020).</li></ol>

The authors have no conflicts of interest to disclose.

The presented protocol describes the procedure of the dendrochronological dating of a violin. The procedure includes several critical steps. The first one is to identify the tree rings in order to properly measure their width. This is critical because the tree rings are often very narrow or have unclear boundaries due to the small amount of latewood (step 1.3). The detection of tree rings can be complicated by aging of the wood, dark and opaque varnishes28, or damage, repairs, retouching, or dirt ...

An erratum was issued for:&#160;<a href="https://www.jove.com/t/64591">Dendrochronological Dating and Provenancing of String Instruments</a>. The Authors section was updated from:
Katarina &#268;ufar1 
Bla&#382; Dem&#353;ar2 
Micha Beuting3 
Angela Balzano1 
Nina &#352;krk1 
Luka Kr&#382;e1 
Maks Merela1 
1Department of Wood Science and Technology, Biotechnical Faculty, University of Ljubljana 
2University of Ljubljana 
3Universitat Hamburg
to:
Katarina &#268;ufar1 
Bla&#382; Dem&#353;ar2 
Micha Beuting2 
Angela Balzano1 
Nina &#352;krk1 
Luka Kr&#382;e1 
Maks Merela1 
1Department of Wood Science and Technology, Biotechnical Faculty, University of Ljubljana 
2Independent Scholar

An erratum was issued for:&#160;<a href="https://www.jove.com/t/64591">Dendrochronological Dating and Provenancing of String Instruments</a>. The Authors section was updated.

Erratum: Dendrochronological Dating and Provenancing of String Instruments

The goal of this study is to present a protocol for the dendrochronological analysis of tree rings on the top plate of a wooden musical stringed instrument. Dendrochronology is used as a method to determine the age of the wood of the instrument by determining the year in which the youngest tree ring on the plate was formed and after which the instrument was made (or before which the instrument could not have been made).
Dating a musical instrument (such as a violin) is an important step in its authentication1,2,3,4,5,6. It is a complex process that involves the year in which the instrument was made, as well as the maker or instrument-making school or geographical area. To do this, dendrochronology is often combined with other techniques, which include the study of the label on the instrument (which is often not reliable) and the inspection of the instrument and its parts such as the outlines, scroll, wood figure and aging, varnish, f-holes, and purfling (Figure 1). The authentication can only be done by experts5,6,7.
<img alt="Figure 1" class="xfigimg" src="/files/ftp_upload/64591/64591fig01.jpg" /> 
Figure 1: The top of the violin and its parts. The wood of the top plate (also called the front plate, belly, or soundboard) made of Norway spruce (Picea abies) can be dated by dendrochronology. The characteristics and dimensions of other parts such as the scroll, f-holes, and purfling are studied by organologists and help to authenticate the instrument. Scale = 20 cm. <a href="https://www.jove.com/files/ftp_upload/64591/64591fig01large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
Dendrochronology is the science of dating tree rings in the wood, also called annual rings, growth rings, or growth layers, which are formed every year in the trees of temperate zones. Dendrochronology clarifies in which calendar year a particular tree ring was formed. By dating the outermost and most recently formed tree ring just below the bark, the last year of a tree&#39;s life before it was cut down can be determined.
Dendrochronology is based on the principle that annual variations in tree ring width (and other characteristics) are largely influenced by the environment, especially the climate, in which the trees grow. When conditions are similar over an area, trees of the same species show similar tree ring variations from year to year8. This means that the tree ring series (i.e., the temporal sequence of tree ring widths over time) is similar for trees of the same species in the same area.
The dating of wooden instruments follows the principles used for dating historical objects. In most cases, it is based on measuring tree ring width, creating tree ring series of the same object, cross-dating (to determine their matching position), and averaging them into a floating chronology of an object showing the tree ring series in relative time3,4,6.
Absolute dating (determining the calendar year of tree ring formation) is accomplished by cross-dating with one or more reference chronologies established for a particular tree species and geographic area4,6.&#160;The reference chronologies must be based on the tree ring widths of a sufficient number of trees (replication) and should be long enough to cover the period of interest.
Dendrochronology is regularly applied to determine the age of stringed instruments such as violins, violas, and cellos1,9,10,11,12,13. For stringed instruments, the wood of the top plates (also the front plate, belly, or soundboard) can be dated. They are usually made of Norway spruce (Picea abies) or silver fir (Abies alba)4,6,13. The measurements must be made in a non-invasive way directly on the instrument or by using images. The measurements are usually made at different locations on the top plate to establish a sequence for the instrument that can be dated with reference chronologies.
Dating is the most critical step because a reference chronology must be available for the species, geographic area, and time period of the instrument being studied. Many chronologies are available at the International Tree Ring Data Bank (ITRDB)14,&#160;but only a few are of Norway spruce or silver fir from the region covering the period of interest6; therefore, dendrochronology laboratories put a lot of effort into constructing reference chronologies. The likelihood of dating increases if a network of chronologies is available, including those from exactly defined forest sites, dated instruments, and instrument collections from various manufacturers like the Stradivari, Guarneri, and Amati families from Italy5,6,15,16, Jacob Stainer from Austria, as well as Joachim Tielke and members of the Hoffmann family from Germany17,18,19. The fine historical instruments made by the manufacturers in the 16th century to 18th century are most prized by musicians and collectors, although the importance of many less-known makers is also growing3,4,6,12.
Dendrochronology provides the end date, which must be considered the terminus post quem &#8211;&#160;the year after which the instrument was made. Dendrochronology is also used for dendroprovenancing, which helps to determine the geographic origin of the wood and to assign instruments to specific violin makers or violin-making schools3,4,6.
The dendrochronological end date almost never coincides exactly with the year the instrument was made, and the latter must, thus, be estimated, which requires a lot of supporting information and cooperation between experts of different fields.

<table border="1" fo:keep-together.within-page="1" fo:keep-with-next.within-page="always">
	<tbody>
		<tr>
			<td>CDendro</td>
			<td>Cybis Elektronik &#38; Data AB</td>
			<td>https://www.cybis.se</td>
			<td>program CoDendro for dendro data management and crossdating</td>
		</tr>
		<tr>
			<td>CooRecorder</td>
			<td>Cybis Elektronik &#38; Data AB</td>
			<td>https://www.cybis.se</td>
			<td>program CooRecorder to measure tree ring widths on images</td>
		</tr>
		<tr>
			<td>TSAP-Win</td>
			<td>RINNTECH</td>
			<td>https://rinntech.info/products/tsap-win/</td>
			<td>Time series analysis software</td>
		</tr>
	</tbody>
</table>

dendrochronological dating and provenancing of string instruments

Dendrochronology, the science of dating tree rings in the wood, defines in which calendar year a particular tree ring was formed. The method can be used to determine the age and authentication of wooden musical instruments. We present a protocol describing how to perform a dendrochronological analysis on stringed instruments and how to interpret the dating. The protocol describes the basic steps in the analysis of top plates, which are usually made of Norway spruce (Picea abies) or, more rarely, silver fir (Abies alba). First, the top plate is carefully inspected, and then the tree ring widths are measured directly on the instrument using high-resolution images. After completing the measurements, a tree ring sequence of the instrument is created, and, in the next step, dating is performed with a number of reference chronologies of the tree species from different geographical areas and instruments. The specialists who date the instruments also invest work in creating reference chronologies. The dendrochronological report provides the dating of an instrument as a calendar year (end date), indicating the year in which the last (most recent) tree ring on the top plate was formed when the tree was still alive. The end date represents the terminus post quem, the year after which the instrument was made or before which it could not have been made. To estimate the year of manufacture, one must consider the time required for wood drying and storing and the number of tree rings removed during wood processing. This protocol is intended to help those commissioning such an analysis to better understand how the analysis is performed and how to interpret the dendrochronological reports in terms of the age, origin, maker, and authenticity of the instrument.

A typical case in which a dendrochronological study was requested is a violin allegedly made by Andrea Guarneri of Cremona belonging to the family/school that produced numerous valuable instruments16,24. The violin in question contained two labels. One stated that the instrument was made by Andrea Guarneri of Cremona in 1747, while the other stated only 1867. However, the organological examination of the violin (Figure 3) suggested t...

Watch this Scientific Journal Video about Dendrochronological Dating and Provenancing of String Instruments at JoVE.com

Dendrochronological Dating and Provenancing of String Instruments

The dendrochronological analysis of a stringed instrument requires inspecting the top plate, measuring the tree ring widths, establishing the chronology of the instrument, and dating through determining the end date-the year of the formation of the most recent tree ring.

Dendrochronology, the science of dating tree rings in the wood, defines in which calendar year a particular tree ring was formed. The method can be used ...

dendrochronological-dating-and-provenancing-of-string-instruments

Research

JoVE Journal

Environment

2.4K Views.  University of Ljubljana. The dendrochronological analysis of a stringed instrument requires inspecting the top plate, measuring the tree ring widths, establishing the chronology of the instrument, and dating through determining the end date-the year of the formation of the most recent tree ring. 

Video: Dendrochronological Dating and Provenancing of String Instruments

Design and Construction of an Urban Runoff Research Facility

As the urban population increases, so does the area of irrigated urban landscape. Summer water use in urban areas can be 2-3x winter base line water use due to increased demand for landscape irrigation. Improper irrigation practices and large rainfall events can result in runoff from urban landscapes which has potential to carry nutrients and sediments into local streams and lakes where they may contribute to eutrophication. A 1,000 m2 facility was constructed which consists of 24 individual 33.6 m2 field plots, each equipped for measuring total runoff volumes with time and collection of runoff subsamples at selected intervals for quantification of chemical constituents in the runoff water from simulated urban landscapes. Runoff volumes from the first and second trials had coefficient of variability (CV) values of 38.2 and 28.7%, respectively. CV values for runoff pH, EC, and Na concentration for both trials were all under 10%. Concentrations of DOC, TDN, DON, PO4-P, K+, Mg2+, and Ca2+ had CV values less than 50% in both trials. Overall, the results of testing performed after sod installation at the facility indicated good uniformity between plots for runoff volumes and chemical constituents. The large plot size is sufficient to include much of the natural variability and therefore provides better simulation of urban landscape ecosystems.

This paper describes the design, construction, and function of a 1,000 m2 facility containing 24 individual 33.6 m2 field plots equipped for measuring total runoff volumes with time and collection of runoff subsamples at selected intervals for quantification of chemical constituents in the runoff water from simulated home lawns.

As the urban population increases, so does the area of irrigated urban landscape. Summer water use in urban areas can be 2-3x winter base line water use ...

Integrated Field Lysimetry and Porewater Sampling for Evaluation of Chemical Mobility in Soils and Established Vegetation

Potentially toxic chemicals are routinely applied to land to meet growing demands on waste management and food production, but the fate of these chemicals is often not well understood. Here we demonstrate an integrated field lysimetry and porewater sampling method for evaluating the mobility of chemicals applied to soils and established vegetation. Lysimeters, open columns made of metal or plastic, are driven into bareground or vegetated soils. Porewater samplers, which are commercially available and use vacuum to collect percolating soil water, are installed at predetermined depths within the lysimeters. At prearranged times following chemical application to experimental plots, porewater is collected, and lysimeters, containing soil and vegetation, are exhumed. By analyzing chemical concentrations in the lysimeter soil, vegetation, and porewater, downward leaching rates, soil retention capacities, and plant uptake for the chemical of interest may be quantified. Because field lysimetry and porewater sampling are conducted under natural environmental conditions and with minimal soil disturbance, derived results project real-case scenarios and provide valuable information for chemical management. As chemicals are increasingly applied to land worldwide, the described techniques may be utilized to determine whether applied chemicals pose adverse effects to human health or the environment.

Field lysimetry and porewater sampling allow researchers to evaluate the fate of chemicals applied to soils and established vegetation. The goal of this protocol is to demonstrate how to install required instrumentation and collect samples for chemical analysis during integrated field lysimetry and porewater sampling experiments.

Potentially toxic chemicals are routinely applied to land to meet growing demands on waste management and food production, but the fate of these chemicals ...

Quantification of Heavy Metals and Other Inorganic Contaminants on the Productivity of Microalgae

Increasing demand for renewable fuels has researchers investigating the feasibility of alternative feedstocks, such as microalgae. Inherent advantages include high potential yield, use of non-arable land and integration with waste streams. The nutrient requirements of a large-scale microalgae production system will require the coupling of cultivation systems with industrial waste resources, such as carbon dioxide from flue gas and nutrients from wastewater. Inorganic contaminants present in these wastes can potentially lead to bioaccumulation in microalgal biomass negatively impact productivity and limiting end use. This study focuses on the experimental evaluation of the impact and the fate of 14 inorganic contaminants (As, Cd, Co, Cr, Cu, Hg, Mn, Ni, Pb, Sb, Se, Sn, V and Zn) on Nannochloropsis salina growth. Microalgae were cultivated in photobioreactors illuminated at 984 &#181;mol m-2 sec-1 and maintained at pH 7 in a growth media polluted with inorganic contaminants at levels expected based on the composition found in commercial coal flue gas systems. Contaminants present in the biomass and the medium at the end of a 7 day growth period were analytically quantified through cold vapor atomic absorption spectrometry for Hg and through inductively coupled plasma mass spectrometry for As, Cd, Co, Cr, Cu, Mn, Ni, Pb, Sb, Se, Sn, V and Zn. Results show N. salina is a sensitive strain to the multi-metal environment with a statistical decrease in biomass yieldwith the introduction of these contaminants. The techniques presented here are adequate for quantifying algal growth and determining the fate of inorganic contaminants.

Integration of microalgal cultivation with industrial flue gas will ultimately introduce heavy metals and other inorganic compounds into the growth media. This study presents a procedure used to determine the end fate and impact of heavy metals and inorganic contaminants on the growth of Nannochloropsis salina grown in photobioreactors.

Increasing demand for renewable fuels has researchers investigating the feasibility of alternative feedstocks, such as microalgae. Inherent advantages ...

Clean Sampling and Analysis of River and Estuarine Waters for Trace Metal Studies

Most of the trace metal concentrations in ambient waters obtained a few decades ago have been considered unreliable owing to the lack of contamination control. Developments of some techniques aiming to reduce trace metal contamination in the last couple of decades have resulted in concentrations reported now being orders of magnitude lower than those in the past. These low concentrations often necessitate preconcentration of water samples prior to instrumental analysis of samples. Since contamination can appear in all phases of trace metal analyses, including sample collection (and during preparation of sampling containers), storage and handling, pretreatments, and instrumental analysis, specific care needs to be taken in order to reduce contamination levels at all steps. The effort to develop and utilize "clean techniques" in trace metal studies allows scientists to investigate trace metal distributions and chemical and biological behavior in greater details. This advancement also provides the required accuracy and precision of trace metal data allowing for environmental conditions to be related to trace metal concentrations in aquatic environments.
This protocol that is presented here details needed materials for sample preparation, sample collection, sample pretreatment including preconcentration, and instrumental analysis. By reducing contamination throughout all phases mentioned above for trace metal analysis, much lower detection limits and thus accuracy can be achieved. The effectiveness of "clean techniques" is further demonstrated using low field blanks and good recoveries for standard reference material. The data quality that can be obtained thus enables the assessment of trace metal distributions and their relationships to environmental parameters.

Special care using "clean techniques" is required to properly collect and process water samples for trace metal studies in aquatic environments. A protocol for sampling, processing, and analytical procedures with the aim of obtaining reliable environmental monitoring data and results with high sensitivity for detailed trace metal studies is presented.

Most of the trace metal concentrations in ambient waters obtained a few decades ago have been considered unreliable owing to the lack of contamination ...

Modification and Application of a Leaf Blower-vac for Field Sampling of Arthropods

Rice fields host a large diversity of arthropods, but investigating their population dynamics and interactions is challenging. Here we describe the modification and application of a leaf blower-vac for suction sampling of arthropod populations in rice. When used in combination with an enclosure, application of this sampling device provides absolute estimates of the populations of arthropods as numbers per standardized sampling area. The sampling efficiency depends critically on the sampling duration. In a mature rice crop, a two-minute sampling in an enclosure of 0.13 m2 yields more than 90% of the arthropod population. The device also allows sampling of arthropods dwelling on the water surface or the soil in rice paddies, but it is not suitable for sampling fast flying insects, such as predatory Odonata or larger hymenopterous parasitoids. The modified blower-vac is simple to construct, and cheaper and easier to handle than traditional suction sampling devices, such as D-vac. The low cost makes the modified blower-vac also accessible to researchers in developing countries.

Assessment of arthropod abundance in crops is critical for investigating population dynamics and species interactions. Here we describe the modification and application of a leaf blower-vac for suction sampling of arthropods in rice.

Rice fields host a large diversity of arthropods, but investigating their population dynamics and interactions is challenging. Here we describe the ...

Continuous Hydrologic and Water Quality Monitoring of Vernal Ponds

Vernal ponds, also referred to as vernal pools, provide critical ecosystem services and habitat for a variety of threatened and endangered species. However, they are vulnerable parts of the landscapes that are often poorly understood and understudied. Land use and management practices, as well as climate change are thought to be a contribution to the global amphibian decline. However, more research is needed to understand the extent of these impacts. Here, we present methodology for characterizing a vernal pond's morphology and detail a monitoring station that can be used to collect water quantity and quality data over the duration of a vernal pond's hydroperiod. We provide methodology for how to conduct field surveys to characterize the morphology and develop stage-storage curves for a vernal pond. Additionally, we provide methodology for monitoring the water level, temperature, pH, oxidation-reduction potential, dissolved oxygen, and electrical conductivity of water in a vernal pond, as well as monitoring rainfall data. This information can be used to better quantify the ecosystem services that vernal ponds provide and the impacts of anthropogenic activities on their ability to provide these services.

Understanding the ecosystem services and processes provided by vernal ponds and the impacts of anthropogenic activities on their ability to provide these services requires intensive hydrologic monitoring. This sampling protocol using in-situ monitoring equipment was developed to understand the impact of anthropogenic activities on water levels and quality.

Vernal ponds, also referred to as vernal pools, provide critical ecosystem services and habitat for a variety of threatened and endangered species. ...

Collection and Extraction of Occupational Air Samples for Analysis of Fungal DNA

Traditional methods of identifying fungal exposures in occupational environments, such as culture and microscopy-based approaches, have several limitations that have resulted in the exclusion of many species. Advances in the field over the last two decades have led occupational health researchers to turn to molecular-based approaches for identifying fungal hazards. These methods have resulted in the detection of many species within indoor and occupational environments that have not been detected using traditional methods. This protocol details an approach for determining fungal diversity within air samples through genomic DNA extraction, amplification, sequencing, and taxonomic identification of fungal internal transcribed spacer (ITS) regions. ITS sequencing results in the detection of many fungal species that are either not detected or difficult to identify to species level using culture or microscopy. While these methods do not provide quantitative measures of fungal burden, they offer a new approach to hazard identification and can be used to determine overall species richness and diversity within an occupational environment.

Determining the fungal diversity within an environment is a method utilized in occupational health studies to identify health hazards. This protocol describes DNA extraction from occupational air samples for amplification and sequencing of fungal ITS regions. This approach detects many fungal species that can be overlooked by traditional assessment methods.

Traditional methods of identifying fungal exposures in occupational environments, such as culture and microscopy-based approaches, have several ...

An Ultra-clean Multilayer Apparatus for Collecting Size Fractionated Marine Plankton and Suspended Particles

The distributions of many trace elements in the ocean are strongly associated with the growth, death, and re-mineralization of marine plankton and those of suspended/sinking particles. Here, we present an all plastic (Polypropylene and Polycarbonate), multi-layer filtration system for collection of suspended particulate matter (SPM) at sea. This ultra-clean sampling device has been designed and developed specifically for trace element studies. Meticulous selection of all non-metallic materials and utilization of an in-line flow-through procedure minimizes any possible metal contamination during sampling. This system has been successfully tested and tweaked for determining trace metals (e.g., Fe, Al, Mn, Cd, Cu, Ni) on particles of varying size in coastal and open ocean waters. Results from the South China Sea at the South East Asia Time-Series (SEATS) station indicate that diurnal variations and spatial distribution of plankton in the euphotic zone can be easily resolved and recognized. Chemical analysis of size-fractionated particles in surface waters of the Taiwan Strait suggests that the larger particles (&#62;153 &#181;m) were mostly biologically derived, while the smaller particles (10 - 63 &#181;m) were mostly composed of inorganic matter. Apart from Cd, the concentrations of metals (Fe, Al, Mn, Cu, Ni) decreased with increasing size.

Plankton and suspended particles play a major role in the biogeochemical cycles in the ocean. Here, we provide an ultra-clean, low stress method for the collection of various sizes of particles and plankton at sea with the capability of handling large volumes of seawater.

The distributions of many trace elements in the ocean are strongly associated with the growth, death, and re-mineralization of marine plankton and those ...

Isolation and Analysis of Microbial Communities in Soil, Rhizosphere, and Roots in Perennial Grass Experiments

Plant and soil microbiome studies are becoming increasingly important for understanding the roles microorganisms play in agricultural productivity. The purpose of this manuscript is to provide detail on how to rapidly sample soil, rhizosphere, and endosphere of replicated field trials and analyze changes that may occur in the microbial communities due to sample type, treatment, and plant genotype. The experiment used to demonstrate these methods consists of replicated field plots containing two, pure, warm-season grasses (Panicum virgatum and Andropogon gerardii) and a low-diversity grass mixture (A. gerardii, Sorghastrum nutans, and Bouteloua curtipendula). Briefly, plants are excavated, a variety of roots are cut and placed in phosphate buffer, and then shaken to collect the rhizosphere. Roots are brought to the laboratory on ice and surface sterilized with bleach and ethanol (EtOH). The rhizosphere is filtered and concentrated by centrifugation. Excavated soil from around the root ball is placed into plastic bags and brought to the lab where a small amount of soil is taken for DNA extractions. DNA is extracted from roots, soil, and rhizosphere and then amplified with primers for the V4 region of the 16S rRNA gene. Amplicons are sequenced, then analyzed with open access bioinformatics tools. These methods allow researchers to test how the microbial community diversity and composition varies due to sample type, treatment, and plant genotype. Using these methods along with statistical models, the representative results demonstrate there are significant differences in microbial communities of roots, rhizosphere, and soil. Methods presented here provide a complete set of steps for how to collect field samples, isolate, extract, quantify, amplify, and sequence DNA, and analyze microbial community diversity and composition in replicated field trials.

Excavation of plant roots from the field as well as processing of samples into endosphere, rhizosphere, and soil are described in detail, including DNA extraction and data analysis methods. This paper is designed to enable other laboratories to use these techniques for the study of soil, endosphere, and rhizosphere microbiomes.

Plant and soil microbiome studies are becoming increasingly important for understanding the roles microorganisms play in agricultural productivity. The ...

Generating Homo- and Heterografts Between Watermelon and Bottle Gourd for the Study of Cold-responsive MicroRNAs

MicroRNAs (miRNAs) are endogenous small non-coding RNAs of about 20 - 24 nt, known to play important roles in plant development and adaptation. There is an accumulating evidence showing that the expressions of certain miRNAs are altered when grafting, an agricultural practice commonly used by farmers to improve crop tolerance to biotic and abiotic stresses. Bottle gourd is an inherently climate-resilient crop compared to many other major cucurbits, including watermelon, rendering it one of the most widely used rootstocks for the latter. The recent advancement of high-throughput sequencing technologies has provided great opportunities to investigate cold-responsive miRNAs and their contributions to heterograft advantages; yet, adequate experimental procedures are a prerequisite for this purpose. Here, we present a detailed protocol for efficiently generating homo- and heterografts between the cold-susceptible watermelon and the cold-tolerant bottle gourd, in addition to methods of tissue sampling, data generation, and data analysis. The presented methods are also useful for other plant-grafting systems, to interrogate miRNA regulations under various environmental stresses, such as heat, drought, and salinity.

Here we present a detailed protocol for efficiently making homo- and heterografts between watermelon and bottle gourd, in addition to methods of tissue sampling, data generation, and data analysis, for the investigation of cold-responsive microRNAs.

MicroRNAs (miRNAs) are endogenous small non-coding RNAs of about 20 - 24 nt, known to play important roles in plant development and adaptation. There is ...