Permeabilization of Adhered Cells Using an Inert Gas Jet

Summary

This protocol describes a method for the temporary permeabilization of adherent cells using an inert gas jet. This technique facilitates the transfer of genetic material and biomolecules into adherent mammalian cells by the utilization of mechanical forces to disrupt the plasma membrane.

Abstract

Various cell transfection techniques exist and these can be broken down to three broad categories: viral, chemical and mechanical. This protocol describes a mechanical method to temporally permeabilize adherent cells using an inert gas jet that can facilitate the transfer of normally non-permeable macromolecules into cells. We believe this technique works by imparting shear forces on the plasma membrane of adherent cells, resulting in the temporary formation of micropores. Once these pores are created, the cells are then permeable to genetic material and other biomolecules. The mechanical forces involved do run the risk of permanently damaging or detaching cells from their substrate. There is, therefore, a narrow range of inert gas dynamics where the technique is effective. An inert gas jet has proven efficient at permeabilizing various adherent cell lines including HeLa, HEK293 and human abdominal aortic endothelial cells. This protocol is appropriate for the permeabilization of adherent cells both in vitro and, as we have demonstrated, in vivo, showing it may be used for research and potentially in future clinical applications. It also has the advantage of permeabilizing cells in a spatially restrictive manner, which could prove to be a valuable research tool.

Introduction

With the evolution of biomedicine and the understanding of cell mechanics, the delivery of biomolecules into cells has become vital to many research fields and medical therapies. Different techniques have been developed to introduce foreign molecules through the plasma membrane and into the cell cytosol. These can be generally classified as either: viral, chemical or mechanical techniques. Viral techniques can transfect genetic material such as RNA and DNA using viral vectors¹. Viral techniques tend to have high efficiencies in certain cell lines, however they do have the potential for immune and inflammatory reactions². Common chemical transfection methods include precipitation with calcium phosphate³, bacterial exotoxins⁴ and lipofection⁵. These techniques have proven to be effective; however, certain problems arise such as cell toxicity and non-specificity. Furthermore, techniques such as calcium phosphate precipitation have been found to have transfection efficiencies up to 70% but only in certain cell lines, rarely in primary cells⁶. This is of note as increasing research efforts are being put into primary cells, especially in the case of designing various treatments for clinical use and the study of DNA functioning.

Temporal disruption of the cell membrane through mechanical stimuli is an alternative for introducing foreign molecules into cells. Techniques include: microinjection of molecules⁷, electroporation using an electric field to disrupt the membrane^8,9, sonoporation using ultrasound waves to disrupt the cell membrane^10-12, particle bombardment as demonstrated by the "gene gun", which shoots particles bound with genes into the cell¹³, and more recently, the application of fluid shear stress that has been shown to temporally permeabilize mammalian cells^14,15. Although mechanical methods avoid some of the aforementioned issues, they are typically accompanied by lower efficiencies and very complex and specialized setups. An atmospheric pressure glow discharge torch (APGD-t) was developed at McGill with the initial goal of functionalizing surfaces and detaching adherent cells in vitro¹⁶. Serendipitously, it was discovered that a live/dead stain being used was somehow being taken in by cells without a permeabilizing agent being added. Furthermore, this seemed to have occurred only in restricted areas of the wells which happened to match up with the torch path. Investigation into the permeabilization capabilities of the APGD-t continued and in control studies, it was found that the carrier inert gas jet of the plasma without excitation was also able to permeabilize cells. This contradicted the initial hypothesis that the reactive species created by the plasma jet temporarily impaired the membrane function and suggested that simply the mechanical forces were sufficient to cause cell permeabilization. From here, studies continued in our lab to try and quantify and characterize the permeabilization efficiency of an inert gas jet as well as look at its transfection capabilities¹⁶.

Through these studies, it has been found that micropores do in fact form in the plasma membrane, and these pores tend to reseal within approximately 5 sec¹⁵. We have demonstrated the technique's utility in vitro and in vivo in the chorioallantoic membrane of a chick embryo.

Access restricted. Please log in or start a trial to view this content.

Protocol

1. Development of LabView Program

1. A mass flow controller (MKS M100B Mass-Flo Controller) is attached to the helium gas line to ensure a precise gas flow rate. This unit is controlled by an input voltage, ranging between 0 and 5 V. A control loop in the LabView program determines the required voltage at any given time. Interfacing between the computer and the mass flow controller is performed by a data acquisition device (NI USB-6009), and a 12 V power supply provides power to the mass flow controller.
2. Two positioning linear slides are used to control the movement of the 6-well plate, one for each direction. Each assembly consists of a MA15-series Velmex Unislide Assembly coupled with a stepping motor, and both assemblies are controlled by a single Velmex VXM Stepping Motor Controller. The controller allows for manual jogging of each motor or accepts a string of external serial commands, the combination of which allow for specific movement patterns. Several patterns can be programmed into the LabView program, requiring the user to provide only the desired torch speed as well as the path dimensions.

2. Preparation of Equipment

1. Open both the helium cylinder and regulator.
2. Turn on the motor controller.
3. Open the LabView program and verify all conditions.
4. Make sure the platform is centered. To check, look at each motor stage and verify that each carriage is not near either stage end. Either have the program center the carriages or manually adjust by using the jogging controls on the front of the motor controller.
5. If this is the first run of the day, it is recommended to run the program once without cells, to ensure the setup is working correctly.

3. Preparation of the Gas Jet Capillary Nozzle Height

1. Remove the capillary from the holder and zero the height dial.
2. Place the 6-well plate on the platform.
3. Replace and lower the gas jet capillary to the bottom of the well until it hits the cover slip. Secure the capillary in the holder.
4. Using the height dial, raise the capillary 3 mm. Mark this height on the capillary base.
5. Raise the capillary to a safe height and then remove the 6-well plate.

4. Cell Permeabilization Protocol

1. Culture adherent cell line to confluence on glass cover slips in a 6-well plate using standard culturing techniques. For HeLa cells, seed 6-well plates with 2 x 10⁵ cells per well and incubate for 48 hr before treatment.
2. Prepare appropriate volume of solution containing the desired vector. For hrGFPII-1, a concentration of 50 ng/μl in 1x PBS provides a strong fluorescent signal in HeLa cells 24 hr after transfection. For dextran studies, 80 μg/ml of 10 kDa green fluorescent dextran is recommended. Henceforth, this solution will be referred to as "vector solution".
3. Remove cell culture media from well and rinse three times with 1x PBS.
4. Pipette 1,370 μl of vector solution prepared in step 4.2 into well. This should result in a liquid depth of approximately 1.3 mm.
5. Place the well containing the vector solution in the center of the platform. Lower the gas jet nozzle to the previously marked level indicating a nozzle height of 3 mm above the slide.
6. Set helium flow rate in the LabView program and select the desired movement pattern to be used. Select "Run" when ready to begin the permeabilization protocol. There will be an initial lag period during which the mass flow controller is preparing to provide the necessary flow rate. Once the appropriate flow rate has been reached, the LabView program will activate the stepper motors to move the well in the desired permeabilization pattern. Once the platform has stopped, wait approximately 30 sec and remove the vector solution. Note: Optimal permeabilization occurs near a dynamic pressure of 100 to 200 Pa at the nozzle outlet, depending on the capillary diameter.
7. Wash well three times with 1x PBS.
8. Fill well with fresh culture media.
9. Repeat steps 4.3 - 4.6 for desired number of experiments. Note: Be sure to include control samples which consist of wells being filled with the vector solution without the gas jet being run over them. Leave the solution in the control wells for approximately 1 min then proceed to steps 4.5 and 4.6.
10. If running an hrGFP transfection experiment, return 6-well plate to incubator for 24 hr to allow transfected material to be transcribed by the cells. If running a dextran permeabilization experiment, return 6-well plate to incubator for 15 min.

5. Cell Imaging

1. If desired, immediately before imaging, counterstain with appropriate live/dead stain to evaluate cell death.
2. Image cells with appropriate microscope to investigate transfection/ permeabilization efficacy.

Access restricted. Please log in or start a trial to view this content.

Results

Permeabilization of HeLa cells with 10 kDa green fluorescent dextran using a helium gas jet with a 0.86 mm inner diameter capillary is shown in Figure 1. Cells were counterstained immediately after permeabilization with 2 μl/ml EthD-1 solution (LIVE/DEAD Viability/Cytotoxicity Kit) to visualize cell death. Immediately following counterstaining, cover slips were mounted and imaged. This figure shows results of running the helium gas jet at three different outlet pressures compared to a control sample...

Access restricted. Please log in or start a trial to view this content.

Discussion

Inert gas jet permeabilization is a useful technique for adherent cell transfection. It provides the ability to transfer biomolecules into cells with the use of mechanical forces, which eliminates the need for potentially harmful chemicals or viral vectors. The technique could potentially give researchers and clinicians an efficient and relatively simple way to precisely transfect cells. The selectivity of the permeabilization is also unique allowing researchers to only treat certain cells in a single colony which could ...

Access restricted. Please log in or start a trial to view this content.

Materials

Name	Company	Catalog Number	Comments
Vitality hrGFPII-1	Agilent Technologies Canada	240143-57	Green fluorescent protein for transfection experiments on HeLa cells
Dextran, AlexaFluor 488; 10,000 MW, Anionic, Fixable	Life Technologies Inc.	D22910	dextran for permeabilization experiments
LIVE/DEAD Viability/Cytotoxicity Kit	Life Technologies Inc.	L3224	for counterstaining of mammalian cells
Prolong Gold Antifade Reagent	Invitrogen	P36930	for mounting slides when imaging
Ultra High Purity Helium	Praxair Canada Inc.	HE 5.0UH-T
Hyclone DMEM/ High Glucose Media - 500 ml	Thermo Scientific	SH30022.01	for HeLa cells
Fetal Bovine Serum	Invitrogen	26140079	For DMEM media
Penicillin-Streptomycin, liquid	Invitrogen	15140-122	For DMEM media
Phosphate-Buffered Saline (PBS) 1x			Produced in lab
			Table 1. List of required reagents
6-Well Clear TC-Treated Microplates	Corning	3506
#1 22 x 22 Coverslips	Fisher	12-542B
Glass Capillaries	World Precision Instruments		WPI Sizing Information
ID (mm): 1, 0.86, 0.68, 0.5 Order #: 1B200, 1B150, 1B120, 1B100
Mass-Flo Controller	MKS	M100B01314CS1BV	Mass flow controller, Series M100B, requires an external 12 V power supply
USB-6009 DAQ Device	National Instruments	779026-01
UniSlide Assembly with stepping motor and controller	Velmex		Two series MA15 UniSlide Assemblies, fitted with Vexta 1.8° stepping motors provided by Velmex, and controlled by a VXM Stepping Motor Controller
			Table 2. List of required equipment