Fast Imaging Technique to Study Drop Impact Dynamics of Non-Newtonian Fluids

Summary

Drop impact of non-Newtonian fluids is a complex process since different physical parameters influence the dynamics over a very short time (less than one tenth of a millisecond). A fast imaging technique is introduced in order to characterize the impact behaviors of different non-Newtonian fluids.

Abstract

In the field of fluid mechanics, many dynamical processes not only occur over a very short time interval but also require high spatial resolution for detailed observation, scenarios that make it challenging to observe with conventional imaging systems. One of these is the drop impact of liquids, which usually happens within one tenth of millisecond. To tackle this challenge, a fast imaging technique is introduced that combines a high-speed camera (capable of up to one million frames per second) with a macro lens with long working distance to bring the spatial resolution of the image down to 10 µm/pixel. The imaging technique enables precise measurement of relevant fluid dynamic quantities, such as the flow field, the spreading distance and the splashing speed, from analysis of the recorded video. To demonstrate the capabilities of this visualization system, the impact dynamics when droplets of non-Newtonian fluids impinge on a flat hard surface are characterized. Two situations are considered: for oxidized liquid metal droplets we focus on the spreading behavior, and for densely packed suspensions we determine the onset of splashing. More generally, the combination of high temporal and spatial imaging resolution introduced here offers advantages for studying fast dynamics across a wide range of microscale phenomena.

Introduction

Drop impact onto a solid surface is a key process in many applications involving electronic fabrication¹, spray coating², and additive manufacturing using inkjet printing^3,4, where a precise control of drop spreading and splashing is desired. However, direct observation of drop impact is technically challenging for two reasons. First, it is an intricate dynamic process that occurs within a timescale too short (~100 µsec) to be imaged easily by conventional imaging systems, such as optical microscopes and DSLR cameras. Flash photography can of course image much faster, but does not allow for continuous recording, as required for detailed analysis of the evolution with time. Second, the length scale induced by impact instabilities can be as small as 10 µm ⁵. Therefore, to quantitatively study the impact process a system that combines ultrafast imaging along with reasonably high spatial resolution is often desired. In the absence of such system, early work on droplet impact focused mostly on the global geometric deformation after impact^6-8, but was unable to gather information about the early time, nonequilibrium processes associated with impact, such as the onset of splashing. Recent advances in CMOS high speed videography of fluids^9,12 have pushed the frame rate up to one million fps and exposure times down below 1 µsec. Furthermore, newly developed CCD imaging techniques can push the frame rate well above one million fps^9-12. Spatial resolution on the other hand, can be increased to the order of 1 µm/pixel using magnifying lenses¹². As a consequence, it has become possible to explore in unprecedented detail the influence of a wide range of physical parameters on various stages of drop impact and to systematically compare experiment and theory^5,13-16. For instance, the splashing transition in Newtonian fluids was found to be set by atmosphere pressure⁵, while the intrinsic rheology decides the spreading dynamics of yield-stress fluids¹⁷.

Here a simple yet powerful fast imaging technique is introduced and applied to study the impact dynamics of two types of non-Newtonian fluids: liquid metals and densely packed suspensions. With exposure to air, essentially all liquid metals (except mercury) will spontaneously develop an oxide skin on their surface. Mechanically, the skin is found to alter effective surface tension and wetting ability of the metals¹⁸. In a previous paper¹⁵, several of the authors studied the spreading process quantitatively and were able to explain how the skin effect influences the impact dynamics, especially the scaling of the maximum spreading radius with impact parameters. Since liquid metal has high surface reflectivity, careful adjustment of the lighting is required in the imaging. Suspensions are composed of small particles in a liquid. Even for simple Newtonian liquids, the addition of particles results in non-Newtonian behavior, which becomes especially pronounced in dense suspensions, i.e. at high volume fraction of suspended particles. Particularly, the onset of splashing when a suspension droplet hits a smooth, hard surface was studied in the previous work¹⁶. Both liquid-particle and inter-particle interactions can change the splashing behavior significantly from what might be expected from simple liquids. To track particles as small as 80 µm in these experiments a high spatial resolution is needed.

A combination of various technical requirements such as high temporal and spatial resolution, plus the capability for observing impacts both from the side and from below, can all be satisfied with the imaging setup described here. By following a standard protocol, described below, the impact dynamics can be investigated in a controlled fashion, as shown explicitly for spreading and splashing behavior.

Protocol

1. Fast Imaging Setup (See Figure 1)

1. Start by setting up a vertical track along which a container filled with the fluid to be studied can be freely moved to adjust the impact velocity. The fluid leaves the bottom of the container through a nozzle and then enters free fall. For this work the falling height was varied from 1-200 cm to give an impact velocity V₀ = (0.4-6.3)±0.15 m/sec.
2. Construct and mount a frame to hold the horizontal impact plane, typically a glass plate, under which an inclined reflective mirror is positioned for visualizing the drop impact from the bottom.
3. Place a clean and smooth glass plate onto the holder. Make sure the plate is leveled horizontally.
4. Mount a syringe pump onto the vertical track.
5. For liquid metal impact, place a transparent paper diffuser behind the nozzle for side-view imaging. At the same time, attach a white opaque paper above the syringe pump to generate reflection for bottom viewing (see Figure 1). Then, locate the light source behind the nozzle.
6. For dense suspension impact, no diffuser is needed. Instead, just place the light source in front of the imaging plane.
7. Select the macro lens with an appropriate focal length for desired magnification and optical working distance. Then, connect the lens to the camera.
8. Mount the camera onto a tripod and adjust the height of camera according to the imaging perspective (side or bottom).

2. Sample Preparation

1. Preparation of oxidized liquid metal
   1. Store Gallium-Indium Eutectic (eGaIn) in a sealed container. Since its melting temperature is about 15 °C, eGaIn stays in a liquid state at room temperature.
   2. Use a pipette to extract 3 ml eGaIn from the container and extrude it onto an acrylic plate. Wait 30 min for the sample to be fully oxidized in air. As a consequence, a thin layer of wrinkled oxidized skin completely covers the sample surface.
   3. Use hydrochloric acid (HCl; "CAUTION") of different concentrations to prewash the eGaIn sample and to control the surface oxidation. Specifically, shear the sample, while it is in the acid bath, at 60 sec^-1 shear rate with a rheometer. After 10 min of shear, the level of surface oxidation in the sample reaches equilibrium, set by the HCl concentration^15,18.
   4. After this prewash, use a plastic syringe with a steel nozzle tip to extract eGaIn from the bath.
   5. Mount the syringe onto the syringe pump and be ready for the experiment.
2. Preparation of dense suspensions
   1. Cut off the end of a commercial syringe (4.5 mm or 2.3 mm in radius) and use it as cylindrical tube for dispensing the dense suspension.
   2. Pull back the piston and fill the syringe with water all the way to the open end, making sure there is no air bubble entrained.
   3. Put spherical ZrO₂ or glass beads into the syringe. With the sedimentation of particles, water will spill out from the nozzle. Fill the syringe with particles all the way to the open end. The suspension will jam under gravity.
   4. Use a razor blade to remove extra wetted particles from the top to keep that end flat.
   5. Flip over the nozzle and mount it onto the syringe pump. Surface tension will prevent the particles from falling out¹⁶.

3. Calibration

Before collecting videos, the parameters of the imaging device have to be set and lighting alignment has to be completed. Also, the spatial resolution needs to be calibrated.

1. Start the syringe pump at a speed of 20 ml/hr to push out the fluid (liquid metal or suspension) from the nozzle.
2. Wait for the fluid to detach from the syringe, form a drop and fall off to make a test impact onto the glass substrate.
3. Adjust the camera position, including its vertical position and imaging orientation, to find the splat in the computer monitor that connects to the camera. Modify the working distance to arrange the image to be in the focal plane when the reproduction ratio of the lens is fixed at 1:1.
4. Vary the aperture size, exposure time and lighting angle to obtain the best image quality when the frame rate is high enough (>6,000 fps). Figure 2(a) shows typical images taken by the camera for both liquid eGaIn and a dense suspension.
5. Place a ruler in the field of view (see Figure 2(b)) and calculate the spatial resolution by counting how many pixels fit across 1 cm. Make sure there is no difference in resolution between horizontal and vertical directions.
6. Follow a 3-step process to measure the packing fraction of dense suspension drop:
   1. Measure the mass of the entire splat right after impact (e.g. by letting the drop fall into a measuring cup that can be weighed accurately).
   2. Then, evaporate all solvent with a heater and weigh the splat again to obtain the particle mass.
   3. Calculate the volume of particles and liquid to get the packing fraction. Typically, this volume fraction should be around 60%.
7. According to the observation direction (bottom or side), position the camera appropriately. In particular, put the camera next to the substrate for the side view or on the same level of the reflective mirror for bottom imaging.

4. Video Recording and Data Acquisition

1. After imaging calibration, restart the syringe pump. At the same time, open the camera controlling software to monitor the impact process.
2. Set the post-triggering frame numbers at roughly half of the video length. Watch carefully when the drop starts to form and manually trigger the camera at the moment when drop detaches from the nozzle. Perform a few practice tests before data recording.
3. After the data is recorded, trim down the video to the portion containing the impact and save the videos as image sequences for analysis.

5. Image Post-processing and Analysis

1. Use a boundary detection method to locate the moving front of liquid eGaIn as it spreads, which corresponds to a sharp transition in the average pixel value (see Figures 3(a-b)).
2. From both bottom and side images, determine the splashing onset of dense suspension.
3. Perform particle-tracking algorithms to obtain traces of individual particles that escaped from the splat (see Figure 3(c)). Then, calculate the ejecting velocity from such trajectories (Figure 3(d)).

Results

The fast imaging technique can be used to quantify spreading and splashing for various impact scenarios. Figure 4(a), for instance, shows typical impact image sequences for liquid eGaIn with different oxide skin strength. By ejecting eGaIn from the same nozzle and at the same falling height, droplets with reproducible impact velocity V₀ = 1.02±0.12 m/sec and radius R₀ = 6.25±0.10 mm were generated. The left column shows the impact of an air-oxidized eGa...

Discussion

Several steps are critical for proper execution of the fast imaging. First, camera and lens have to be appropriately set up and calibrated. In particular, in order to get high spatial resolution, the reproduction ratio of the lens must be kept close to 1:1. This is especially important for the visualization of dense suspensions. Also, the aperture size needs to be carefully chosen for imaging. For instance, observation from the side in general requires a longer depth of field, therefore smaller aperture size. To maintain...

Materials

Name	Company	Catalog Number	Comments
Gallium-Indium Eutectic	Sigma Aldrich	495425-25G
Hydrochloric Acid	Sigma Aldrich	320331-2.5L
Zirconium oxide	Glen Mills Inc.	7200
Phantom V12 and V7 Fast Ccamera	Vision Research	N/A
105 mm Micro-Nikon	Nikon	N/A
12 V / 200 W light Source	Dedolight	N/A
Syringe Pump	Razel	MODEL R9-9E