Microscopy-based Assays for High-throughput Screening of Host Factors Involved in Brucella Infection of Hela Cells

Summary

Two assays for microscopy-based high-throughput screening of host factors involved in Brucella infection are described. The entry assay detects host factors required for Brucella entry and the endpoint assay those required for intracellular replication. While applicable for alternative approaches, siRNA screening in HeLa cells is used to illustrate the protocols.

Abstract

Brucella species are facultative intracellular pathogens that infect animals as their natural hosts. Transmission to humans is most commonly caused by direct contact with infected animals or by ingestion of contaminated food and can lead to severe chronic infections.

Brucella can invade professional and non-professional phagocytic cells and replicates within endoplasmic reticulum (ER)-derived vacuoles. The host factors required for Brucella entry into host cells, avoidance of lysosomal degradation, and replication in the ER-like compartment remain largely unknown. Here we describe two assays to identify host factors involved in Brucella entry and replication in HeLa cells. The protocols describe the use of RNA interference, while alternative screening methods could be applied. The assays are based on the detection of fluorescently labeled bacteria in fluorescently labeled host cells using automated wide-field microscopy. The fluorescent images are analyzed using a standardized image analysis pipeline in CellProfiler which allows single cell-based infection scoring.

In the endpoint assay, intracellular replication is measured two days after infection. This allows bacteria to traffic to their replicative niche where proliferation is initiated around 12 hr after bacterial entry. Brucella which have successfully established an intracellular niche will thus have strongly proliferated inside host cells. Since intracellular bacteria will greatly outnumber individual extracellular or intracellular non-replicative bacteria, a strain constitutively expressing GFP can be used. The strong GFP signal is then used to identify infected cells.

In contrast, for the entry assay it is essential to differentiate between intracellular and extracellular bacteria. Here, a strain encoding for a tetracycline-inducible GFP is used. Induction of GFP with simultaneous inactivation of extracellular bacteria by gentamicin enables the differentiation between intracellular and extracellular bacteria based on the GFP signal, with only intracellular bacteria being able to express GFP. This allows the robust detection of single intracellular bacteria before intracellular proliferation is initiated.

Introduction

Brucella species are gram-negative, facultative intracellular pathogens belonging to the class of α-Proteobacteria. They cause abortions and infertility in their natural hosts such as cattle, goats, or sheep resulting in severe economic losses in endemic areas. Brucellosis is one of the most important zoonotic diseases worldwide causing over half a million new human infections annually¹. Transmission to human is most commonly caused by direct contact with infected animals or by ingestion of contaminated food such as unpasteurized milk. Symptoms of the febrile disease are unspecific, which causes difficulties in the diagnosis of brucellosis. If untreated, patients can develop a chronic infection with more severe symptoms such as arthritis, endocarditis, and neuropathy².

On the cellular level Brucella is able to invade phagocytic and non-phagocytic cells and replicates within an intracellular compartment known as the Brucella-containing vacuole (BCV). Internalization of bacteria requires actin cytoskeleton rearrangements by Rac, Rho, and direct activation of Cdc42³. Inside the eukaryotic host cell, the BCV traffics along the endocytic pathway and despite the interaction with lysosomes, bacteria manage to avoid degradation⁴. Acidification of the BCV by the vesicular ATPase is required to induce the expression of the bacterial type IV secretion system (T4SS)⁵. It is believed that bacterial effectors secreted by the T4SS are essential for Brucella to establish its replicative niche, since deletion of the T4SS⁶ or inhibition of the vesicular ATPase lead to defects in the establishment of the intracellular niche⁷. Bacteria do not replicate during the phase of trafficking until they reach an ER-derived vacuolar compartment⁸. Once intracellular proliferation occurs, the BCV is found in close association with ER markers such as calnexin and glucose-6-phosphatase⁶.

The molecular mechanisms by which Brucella enters cells, avoids lysosomal degradation, and finally replicates in an ER-like compartment remain largely unknown. Host factors involved in different steps of infection have mainly been identified by targeted approaches or a small scale small interfering RNA (siRNA) screen performed in Drosophila cells⁹. These have shed light on the contribution of individual host factors during Brucella infection but we are still far from a comprehensive understanding of the entire process.

Here, protocols that allow the identification of human host factors using large-scale RNA interference (RNAi) screening in combination with automated wide-field fluorescence microscopy and automated image analysis are presented. Reverse siRNA transfection of HeLa cells is performed as described earlier^10,11 with minor modifications. The endpoint assay covers a large part of the Brucella intracellular lifecycle except the egress and the infection of neighboring cells. To further characterize the hits identified in the endpoint assay, a modified protocol to identify factors involved in early steps of the infection is used.

A Brucella abortus strain that constitutively expresses GFP is used for the endpoint assay where bacteria are allowed to infect cells for two days. During this time, bacteria enter cells, traffic to the ER-derived replicative niche, and replicate in the peri-nuclear space. The high levels of GFP signal can then be used to reliably detect individual cells which contain replicating bacteria.

To study Brucella entry in a high-throughput assay, it is important to be able to distinguish between intracellular and extracellular bacteria. The method presented here circumvents differential antibody staining of intracellular and extracellular bacteria. It is based on a Brucella strain expressing a tetracycline-inducible GFP in combination with constitutive expression of dsRed. The presence of a constitutive dsRed marker allows identification of all bacteria that are present in the sample. GFP expression is induced by the addition of the non-toxic tetracycline analog anhydrotetracycline (aTc) simultaneously with inactivation of extracellular bacteria by gentamicin (Gm). While the cell-impermeable antibiotic Gm kills extracellular bacteria, aTc can enter the host cell and induce GFP expression selectively in intracellular bacteria. This dual reporter allows the robust separation of single intracellular bacteria (GFP and dsRed signal) from extracellular bacteria (only dsRed signal) using wide-field microscopy. In order to reach detectable GFP expression by intracellular Brucella we have found that 4 hr of induction by aTc results in a reliable signal. Similar induction schemes to selectively express GFP in intracellular bacteria has been used previously to study intracellular Shigella¹².

Protocol

Note: All work with live Brucella abortus strains must be performed inside a biosafety level 3 (BSL3) laboratory considering all required regulations and safety precautions.

1. Preparation of Screening Plates and Culturing of Bacteria and Cells

1. Preparation of Brucella abortus Starter Cultures
   1. Streak Brucella abortus 2308 (B. abortus) from -80 °C milk stock on a Tryptic Soy Agar (TSA) plate containing 50 µg/ml kanamycin (TSA/Km). Incubate plate for 3-4 days at 37 °C. Use strain Brucella abortus 2308 pJC43 (apHT::GFP)¹³ for the endpoint assay and strain Brucella abortus pAC042.08 (apht::dsRed,tetO::tetR-GFP) for the entry assay.
      Note: The smooth lipopolysaccharide (LPS) of Brucella abortus is an important virulence determinant but rough mutants can occur at relatively high frequencies¹⁴. We thus recommend testing the status of the culture strain before starting with this experiment.
   2. Restreak bacteria on four TSA/Km plates covering the full plate and incubate for 2-3 days at 37 °C.
   3. Using a disposable plastic loop, transfer and resuspend bacteria from the TSA/Km plates in 10 ml 10% autoclaved skim milk. Make sure that the bacteria are well resuspended to ensure consistent bacterial concentrations in all starter cultures.
   4. Aliquot 250 µl of the bacterial suspension into 2 ml screw cap tubes and freeze at -80 °C.
   5. Thaw an aliquot of the starter culture and transfer 25 µl, 50 µl, and 100 µl of the bacterial starter culture to separate 250 ml screw cap bottles with 50 ml Tryptic Soy Broth (TSB) containing 50 µg/ml kanamycin (TSB/Km). Seal the bottles with Parafilm.
   6. Incubate the bottles overnight on an orbital shaker at 100 rpm and 37 °C.
   7. Measure the optical density at 600 nm (OD₆₀₀) to determine the volume of starter culture required to reach an OD₆₀₀ = 0.8-1.1 after overnight culture.
2. Preparation of HeLa Cells
   1. Grow HeLa cells in Dulbecco Modified Eagle Medium (DMEM) supplemented with 10% fetal calf serum (FCS) (DMEM/10% FCS) in a 37 °C humid incubator with 5% CO_2. Grow cells to 80% confluency.
3. Prepare the Screening Plates with siRNAs.
   1. Dilute siRNAs in RNase-free water to a final concentration of 0.32 µM. Transfer 5 µl/well to black clear-well flat-bottom 384-well plates.
      1. Use columns 1, 2, 23, and 24 for standard controls. For negative controls, use non-targeting siRNA (scrambled) and mock wells without siRNAs (transfection reagent only). For transfection controls, use an siRNA that induces cell death (KIF11), as well as positive controls of known host factors involved in Brucella infection (e.g., ARPC3, a component of the Arp2/3 complex involved in actin polymerization). Transfer commercially available siRNA libraries or custom siRNAs to the remaining wells.
      2. Seal plates with peelable aluminum foils. Store plates at -20 °C.
         Note: Plates can be stored at -20 °C for at least 6 months and up to years depending on the manufacturer's recommendations.

2. Reverse siRNA Transfection

1. Thaw a black 384-well plate by centrifugation at 300 x g for 20 min at room temperature.
   Note: This will bring down all the liquid which might adhere to the lid or the side of the wells.
2. Prepare the transfection medium by diluting the transfection reagent 1:200 in DMEM without FCS at room temperature. Prepare the transfection medium no longer than 20 min prior to use. Carefully mix the solution before use.
3. Add 25 µl transfection medium to each well using a reagent dispenser and mix the solutions by moving the plate back and forth.
4. Incubate the plate for 1 hr at room temperature to allow siRNA/transfection reagent complex formation.
5. In the meantime, prepare HeLa cells by washing the sub-confluent cells of a 75 cm² flask once with 2.5 ml 0.05% trypsin-EDTA in PBS (trypsin).
6. Add 1.5 ml fresh trypsin and transfer the flask to 37 °C for 2-3 min until the cells round up.
7. Resuspend the cells in 10 ml pre-warmed DMEM/16% FCS.
8. Count cells using an automated cell counter and prepare a cell suspension of 10,000 cells/ml in DMEM/16% FCS.
9. Add 50 µl cell suspension to each well using a reagent dispenser resulting in 500 cells/well.
10. Move the plate back and forth to achieve even distribution of the cells. Leave the plate at room temperature for 5-10 min to allow for the cells to settle down.
11. Seal the plate with Parafilm and incubate it for 72 hr on a pre-warmed aluminum plate in a 37 °C humid incubator with 5% CO₂.
    Note: The pre-warmed aluminum plate allows equal temperature distribution throughout the whole 384-well plate.

3. Infection and Fixation

1. One day prior to infection, inoculate the amount determined in 1.1.7 of B. abortus starter culture in 50 ml TSB/Km medium in a 250 ml screw cap bottle. Seal the bottle with Parafilm and grow bacteria overnight at 37 °C and 100 rpm on an orbital shaker to OD₆₀₀ = 0.8-1.1.
2. Measure OD₆₀₀ of the bacterial culture and prepare the infection medium by diluting the bacterial culture in DMEM/10% FCS to achieve the desired multiplicity of infection (MOI).
   Note: To obtain an infection rate of 5-10% in HeLa cells, an MOI of 10,000 is used. A MOI titration curve should be performed for each cell type to obtain optimal infection rates.
3. Exchange the transfection medium of the 384-well plate with 50 µl of the infection medium using an automated plate washer.
4. Centrifuge the 384-well plate at 400 x g and 4 °C for 20 min.
   Note: This helps to synchronize the infection process.
5. Seal the plate with Parafilm and incubate it on a pre-warmed aluminum plate in a 37 °C humid incubator with 5% CO₂ for 4 hr.
6. Wash the cells with DMEM/10% FCS containing 100 µg/ml Gm to inactivate extracellular bacteria using the automated plate washer (use 200 µl/well overflow wash).
   Note: During an overflow wash, the automated plate washer simultaneously dispenses and aspirates medium.
7. For the entry assay, wash cells a second time with DMEM/10% FCS containing 100 µg/ml Gm and 100 ng/ml aTc using the automated plate washer (use 200 µl/well overflow wash).
8. Seal the plate with Parafilm and return it to a pre-warmed aluminum plate in the 37 °C humid incubator with 5% CO₂ for another 40 hr or 4 hr, for the endpoint assay and the entry assay, respectively.
9. For fixation, wash the wells with PBS using the automated plate washer (use 200 µl/well overflow wash).
10. Exchange PBS with 50 µl 3.7% paraformaldehyde in 0.2 M HEPES at pH 7.4 (PFA) using the automated plate washer.
    Note: Caution: PFA is toxic by inhalation, in contact with skin and if swallowed.
11. Incubate for 20 min at room temperature.
12. Exchange the fixation medium with 50 µl PBS using the automated plate washer. Note: The samples are now ready to be taken out from the BSL3 if needed.
    Caution: Removal of any sample from a BSL3 facility is subject to risk assessment and validation of the procedure and depends on the applicable regulations for biosafety.

4. Staining

1. Wash cells twice with 50 µl PBS.
2. Permeabilize cells in 50 µl 0.1% Triton-X-100 in PBS for 10 min.
3. Wash cells three times with PBS. Add 20 µl of PBS containing 1 µg/ml DAPI (4',6-diamidino-2-phenylindole) and incubate for 30 min at room temperature.
4. Wash cells three times in PBS and protect the staining from light with an aluminum foil.

5. Imaging

1. Set up the automated wide-field microscope for image acquisition.
   Note: The settings for a Molecular Device ImageXpress microscope using MetaXpress software are described below. Alternative 2D wide-field microscopy devices with appropriate hardware specifications and imaging software can be used (see Table of Material/Equipment for details).
   1. Select 10X objective, camera binning = 1, gain = 1.
   2. Select the plate format corresponding to the 384-well plate.
   3. Acquire 9 sites per well.
   4. Use "Enable laser based focus" and "Focus on plate and well bottom".
   5. Set "First well" as the initial well for finding the sample and "All sites" for site autofocus.
   6. Use the DAPI channel to manually set Z-Offset for focus.
   7. Manually select the Z-Offset from DAPI for all other channels.
   8. Manually correct the exposure time for all channels to ensure a wide dynamic range with low overexposure.
      1. Acquire an image of a representative site using the auto-exposure function. Use this exposure time to image 3-5 sites throughout the plate and adjust the exposure time manually until the brightest pixels reach ~80% of the maximal brightness over all sites.
   9. Image the full plate using the DAPI and GFP channels for the endpoint assay. For the entry assay select the RFP channel in addition.

6. Automated Image Analysis

Note: CellProfiler 2¹⁵ is employed as image analysis software to segment cellular and bacterial objects and perform automated measurements within the identified objects. The software provides image analysis algorithms in individual modules, which can be combined into a pipeline that will execute the modules consecutively on all images, to automatically perform a specific image analysis task. To follow the protocol, install CellProfiler 2.1.1 or a newer version. Then, load the provided pipeline and follow the instructions below to adjust the required parameters within the modules. A description of the individual modules of all pipelines can be found in the Supplemental Files.

Note: Two separate pipelines are used for each assay. The first pipeline calculates a shading model, which is used by the second pipeline to correct images prior to analysis. Shading correction is applied to the images to reduce the effects of an inhomogeneous light path from the microscope. Computing the shading model in the first pipeline is a lengthy process, but the results will be of higher accuracy.

1. Endpoint Assay
   1. Calculate the shading model
      1. Go to the Menu "File", select "Import" → "Pipeline from File…", and select the provided pipeline "BrucellaShadingCorrectionPart1-Ver007". When asked whether to convert the legacy pipeline, answer "Don't convert".
      2. Go to "Output" → "View output settings" and select an input folder with the images and an output folder for the resulting shading models.
      3. In Module (1) "LoadImages", adjust the name of the "Text that these images have in common" to match the image names.
      4. Make sure that none of the modules show their display prior to running the full analysis by unchecking all eye symbols next to the modules. Note: This significantly decreases required computational resources while processing the pipeline.
      5. Press "Analyze Images" to start the calculation of the shading model.
   2. Run Image Analysis
      1. Go to the Menu "File", select "Import" → "Pipeline from File…", and select the provided pipeline "BrucellaEndpointWithShadingCorrectionPart2-Ver007". When asked whether to convert the legacy pipeline, answer "Don't convert".
      2. Go to "Output" → "View output settings" and select an input folder with the images and an output folder for the resulting spreadsheet.
      3. In module (1) "LoadImages", adjust the name of the "Text that these images have in common" to match the image names.
      4. In module (2) "LoadSingleImage", load the shading models calculated under 6.1.1 by selecting the location and filenames of the two shading models.
      5. In modules (4) - (5) "ImageMath", adjust the parameter "Multiply the first image by" matching the bit depth of the microscope camera. For 8 and 16 bit images set the parameter to "1.0", for 12 bit images set the parameter to "16.0".
      6. In module (9) "ImageMath" adjust the parameter "Multiply the second image by" to a value (start with 0.25) that will suppress the Brucella signal in the DAPI staining without suppressing the Nuclei.
         1. Click "Start Test Mode", then activate the pause symbol and the display function for module (9) by clicking on the corresponding icons of the module.
            Note: The pause symbol will appear in yellow, while the eye symbol will show an open eye if activated.
         2. Click "Run" to run the analysis up to module (9) with the active pause symbol. To test the values for the module, press "Step".
         3. Right-click the newly opened image and set "Image contrast" to "Log normalized". Repeatedly step back to module (9), adjust the parameter "Multiply the second image by", and step over the module again, until the Brucella signal is fully suppressed while at the same time black areas that indicate over-subtraction are minimized in the result image.
      7. In module (10) "IdentifyPrimaryObjects", set the parameter "Lower bound on threshold" high enough (start with zero) so that nuclei are segmented and background is ignored.
         1. To identify a good value for module (10), step over the module and display the input image as explained in steps 6.1.2.6.1 and 6.1.2.6.2.
         2. Right-click the input image and display the histogram.
            Note: The peak of the histogram typically indicates background.
         3. Starting from background intensity increase the parameter until a good segmentation of nuclei is achieved as displayed in the output image.
            Note: Setting the threshold higher than background intensity is especially important for empty sites.
      8. In module (15) "FilterObjects", adjust the parameter "Minimum value" so that cells with clearly visible Brucella in the nucleus are kept, and all others are filtered away. In this step, ignore Brucella outside the nucleus.
         1. To identify a good value, step over the module and display the output image as explained in steps 6.1.2.6.1 and 6.1.2.6.2. Start from zero, which identifies all cells as infected, and increase the value by small steps until only cells with clearly visible Brucella at the nucleus are kept.
      9. In module (16) "FilterObjects", adjust the parameter "Minimum value" so that cells with clearly visible Brucella at the perinucleus are kept, and all other cells are filtered away. Use a similar approach as in the previous module.
      10. In module (17) "FilterObjects", adjust the parameter "Minimum value" so that cells with clearly visible Brucella at the Voronoi cell body are kept, and all other cells are filtered away. Use a similar approach as in the previous module.
          Note: The Voronoi cell body is a radial extension of the nucleus by 25 pixels with no overlap with neighboring Voronoi cell bodies.
      11. Exit the test mode and make sure that none of the modules show their display prior to running the full analysis by unchecking all eye symbols next to the modules.
          Note: This significantly decreases required computational resources while processing the pipeline.
      12. Press "Analyze Images" to start the analysis.
      13. When the analysis has finished, inspect the resulting PNG images as well as the CSV sheet to ensure that the analysis worked reliably throughout the plate.
2. Entry Assay
   1. Calculate the shading model
      1. Go to the Menu "File", select "Import" → "Pipeline from File…", and select the provided pipeline "BrucellaShadingCorrectionPart1-Ver007". When asked whether to convert the legacy pipeline, answer "Don't convert".
      2. Go to "Output" → "View output settings" and select an input folder with the images and an output folder for the resulting shading models.
      3. In module (1) "LoadImages", adjust the name of the "Text that these images have in common" to match the image names.
      4. Make sure that none of the modules show their display prior to running the full analysis by unchecking all eye symbols next to the modules.
         Note: This significantly decreases required computational resources while processing the pipeline.
      5. Press "Analyze Images" to start the calculation of the shading model.
   2. Run Image Analysis
      1. Go to the Menu "File", select "Import" → "Pipeline from File…", and select the provided pipeline "BrucellaEntryWithShadingCorrectionPart2-Ver007". When asked whether to convert the legacy pipeline, answer "Don't convert".
      2. Go to "Output" → "View output settings" and select an input folder with the images and an output folder for the resulting spreadsheet.
      3. In module (1) "LoadImages", adjust the name of the "Text that these images have in common" to match the image names.
      4. In module (2) "LoadSingleImage", load the shading models calculated under 6.2.1 by selecting the location and filenames of the two shading models.
      5. In modules (4) - (5) "ImageMath", adjust the parameter "Multiply the first image by" matching the bit depth of the microscope camera. For 8 and 16 bit images set the parameter to "1.0", for 12 bit images set the parameter to "16.0".
      6. In module (6) "IdentifyPrimaryObjects", set the parameter "Lower bound on threshold" high enough that only nuclei are segmented and background is ignored.
         1. To identify a good value for module (6), step over the module and display the input image as explained in steps 6.1.2.6.1 and 6.1.2.6.2.
         2. Right-click the input image and display the histogram.
            Note: The peak of the histogram typically indicates background.
         3. Starting from background intensity increase the parameter until a good segmentation of nuclei is achieved as displayed in the output image.
            Note: Setting the threshold above background is important for empty sites.
      7. In module (8) "IdentifyPrimaryObjects", set the parameter "Lower bound on threshold" high enough that only Brucella are segmented and background is ignored.
         1. To identify a good value for module (8), step over the module and display the input image as explained in steps 6.1.2.6.1 and 6.1.2.6.2.
         2. Right-click the input image and display the histogram.
            Note: The peak of the histogram typically indicates background.
         3. Starting from background intensity increase the parameter until good segmentation of Brucella as displayed in the output image is achieved.
            Note: Setting the threshold above background is important for empty sites.
      8. In module (11) "FilterObjects", adjust the parameter "Minimum value" so that background and artefacts are filtered away, and only Brucella colonies are kept.
         1. To identify a good value, step over the module and display the output image as explained in steps 6.1.2.6.1 and 6.1.2.6.2. Start with the value selected in 6.2.2.7 and stepwise increase it until only Brucella objects are kept.
      9. Exit the test mode and make sure that none of the modules show their display prior to running the full analysis by unchecking all eye symbols next to the modules.
         Note: This significantly decreases required computational resources while processing the pipeline.
      10. Press "Analyze Images" to start the analysis.
      11. When the analysis has finished, inspect the resulting PNG images as well as the CSV sheet to ensure that the analysis worked well throughout the plate.

7. Infection Scoring

Note: siRNAs which have a significant impact on cell viability have to be considered with caution, since this can promote false positive discoveries. An altered cell number affects the actual MOI and targeting of essential genes can have pleiotropic effects on pathogen infection. While the incomplete depletion by siRNAs allows for the study of essential genes, such targets have to be validated by alternative methods (e.g., pharmaceutical interference) to corroborate their role as host factors during infection.

1. Endpoint Assay
   1. Open the CSV sheet generated in step 6.1.2.12 and calculate a per well infection rate by dividing the number of infected cells (CellProfiler readout: "Count_InfectedCells") by the total number of cells (CellProfiler readout: "CountNuclei"). If multiple sites per well have been imaged, first summarize all sites for each well, to build a per-well number of infected cells and a per-well total number of cells.
   2. Perform Z scoring normalization to account for plate-to-plate variations if the plates contain sufficient non-hit siRNAs. Assume a sufficient number of non-hit siRNAs per plate if full libraries are screened.
      
2. Entry Assay
   1. Open the CSV sheet generated in step 6.2.2.10 and calculate a per well infection rate by dividing the number of infected cells (CellProfiler readout: "Count_InfectedCells") by the total number of cells (CellProfiler readout: "CountNuclei"). If multiple sites per well have been imaged, first summarize all sites for each well, to build a per-well number of infected cells and a per-well total number of cells.
   2. To quantify the bacterial load of infected cells, estimate the average area occupied by intracellular bacteria per infected cell. To this end, divide the integrated area of all intracellular bacteria overlapping with cells (CellProfiler readout: "AreaOccupied_AreaOccupied_TrueIntPathogenInCells") by the number of infected cells in this site. To account for artefacts, use the median of all sites of this readout as the well readout.
      Note: If this assay is used as a follow up assay containing a large number of genes involved in Brucella infection, do not apply Z score normalization. Instead, perform normalization using mock wells as a reference to account for plate-to-plate variation.

Results

Figure 1A shows an example of image analysis used to automatically identify infected cells in the endpoint assay. Nuclei of HeLa cells stained with DAPI were identified, a peri-nucleus of 8 pixels width surrounding the nucleus, and a Voronoi cell body by extension of the nucleus by 25 pixels were calculated. Since bacteria mainly proliferate in the peri-nuclear space, the GFP intensity in this area of the cell is the most robust measurement to discriminate between infecte...

Discussion

Bacterial pathogens have evolved numerous strategies to manipulate eukaryotic host cells to their benefit. Pathogens causing acute infections often show rapid proliferation which is accompanied by significant alarming of the immune system and loss of viability of infected cells. In contrast, Brucella and other pathogens that cause chronic infections manage to establish long-lasting interactions within host cells. Therefore, bacteria need to fine tune host cell functions to their benefit without disrupting cellul...

Materials

Name	Company	Catalog Number	Comments
Tryptic Soy Agar (TSA)	BD	236950
Tryptic Soy Broth (TSB)	Fluka	22092
Kanamycin sulfate	Sigma-Aldrich	60615
Skim milk
250 ml screw cap bottle	Corning	8396
DMEM	Sigma-Aldrich	D5796
Fetal Calf Serum (FCS)	Gibco	10270	Heat-inactivated
Trypsin-EDTA (0.5%)	Gibco	15400-054	10x stock solution, dilute 1:10 in PBS
Scepte 2.0 Cell Counter	Merck Milipore	PHCC20060	Alternative cell counting devices can be used
Greiner CELLSTAR 384-well plate	Sigma-Aldrich	M2062
Peelable aluminum foil	Costar	6570
Reagent dispenser: "Multidrop 384 Reagent Dispenser"	Thermo Scientific	5840150	Alternative reagent dispenser can be used.
Transfection reagent: "Lipofectamine RNAiMAX	Invitrogen	13778-150
Automated plate washer: "Plate washer ELx50-16"	BioTek	ELX5016	This plate washer contains a 16-channel manifold suitable for 384-well plates. It fits into a biosafety cabinet and has a lid covering the plate during washing which reduces the risk of aerosol production. Alternative plate washers with similar features could be used.
Gentamicin	Sigma-Aldrich	G1397
Anhydrotetracycline hydrochloride	Sigma-Aldrich	37919	100 μg/ml solution in 100% ethanol is kept at -20 °C protected from light in aluminum-foil
PBS	Gibco	20012
Paraformaldehyde	Sigma-Aldrich	P6148	Dissolve in 0.2 M HEPES buffer, pH 7.4. Store at -20 °C and thaw freshly the day before use. Caution, PFA is toxic by inhalation, in contact with skin and if swallowed.
HEPES	Sigma-Aldrich	H3375
Triton X-100	Sigma-Aldrich	T9284
DAPI	Roche	10236276001
Scrambled siRNA	Dharmacon	D-001810-10
Kif11 siRNA	Dharmacon	L-003317-00
ARPC3 siRNA	Dharmacon	L-005284-00
Brucella abortus 2308
pJC43 (apHT::GFP)			Celli et al.12
pAC042.08 (apht::dsRed, tetO::tetR-GFP)			Construction: pJC44 4 was digested with EcoRI followed by generation of blunt ends with Klenov enzyme and subsequent digestion with SalI. TetR-GFP was amplified from pNF106 using primer prAC090 and prAC092. Following digestion with SalI, the TetR-GFP product was ligated to the digested pJC44 vector.
Primer prAC090	Sigma-Aldrich		TTT TTG AAT TCT GGC AAT TCC GAC GTC TAA GAA ACC
Primer prAC092	Sigma-Aldrich		TTT TTG TCG ACT TTG TCC TAC TCA GGA GAG CGT TC
HeLa CCL-2	ATCC	CCL-2
ImageXpress Micro	Molecular Devices	IXM IMAGING MSCOPE	Automated cellular imaging microscope equipped with a precision motorized Z-stage. Alternative systems for automated microscopy and alternative components for hard- and software specified below can be employed.
High-Speed Laser Auto-Focus	Molecular Devices	1-2300-1037
CFI Super Fluor 10X objective	Nikon	MRF00100	N.A 0.50, W.D 1.20 mm, DIC Prism: 10X, Spring loaded
Photometrics CoolSNAP HQ Monochrome CCD Camera	Molecular Devices	1-2300-1060	1,392 x 1,040 imaging pixels, 6.45 x 6.45 µm pixels, 12 bits digitization
MetaXpress software	Molecular Devices	9500-0100
LUI-Spectra-X-7	Lumencor	SPECTRA X V-XXX-YZ	Light engine. The following light sources are used: violet (DAPI), cyan (GFP), green/yellow (RFP)
Single Band Exciter for DAPI	Semrock	FF01-377/50-25
Single Band Emitter for DAPI	Semrock	FF02-447/60-25
Single Band Dichroic for DAPI	Semrock	FF409-Di03-25x36
Single Band Exciter for GFP	Semrock	FF02-472/30-25
Single Band Emitter for GFP	Semrock	FF01-520/35-25
Single Band Dichroic for GFP	Semrock	FF495-Di03-25x36
Single Band Exciter for RFP	Semrock	FF01-562/40-25
Single Band Emitter for RFP	Semrock	FF01-624/40-25
Single Band Dichroic for RFP	Semrock	FF593-Di03-25x36