Establishment of a Clinic-based Biorepository

Summary

Cutaneous tumors are often discarded following Mohs micrographic surgery. A protocol is described here that enables clinical support staff to effectively process and store cutaneous tumor (e.g., squamous cell carcinoma, basal cell carcinoma, and melanoma) samples for downstream laboratory applications without interfering with clinical operations.

Abstract

The incidence of skin cancer (e.g., squamous cell carcinoma, basal cell carcinoma, and melanoma) has been increasing over the past several years. It is expected that there will be a parallel demand for cutaneous tumor samples for biomedical research studies. Tissue availability, however, is limited due the cost of establishing a biorepository and the lack of protocols available for obtaining clinical samples that do not interfere with clinical operations. A protocol was established to collect and process cutaneous tumor and associated blood and saliva samples that has minimal impact on routine clinical procedures on the date of a Mohs surgery. Tumor samples are collected and processed from patients undergoing their first layer of Mohs surgery for biopsy-proven cutaneous malignancies by the Mohs histotechnologist. Adjacent normal tissue is collected at the time of surgical closure. Additional samples that may be collected are whole-blood and buccal swabs. By utilizing tissue samples that are normally discarded, a biorepository was generated that offers several key advantages by being based in the clinic versus the laboratory setting. These include a wide range of collected samples; access to de-identified patient records, including pathology reports; and, for the typical donor, access to additional samples during follow-up visits.

Introduction

Cancer and biomarker research relies on a supply of quality human tissue samples, and limited supply has hindered research^1,2. Many dermatologic studies are limited by the inadequate supply, variable quality, and costs associated with the use of human tissue. The cost of establishing a large, dedicated biobank has been estimated to be approximately two million dollars³, and these costs place the use of human tissue out of the reach of many researchers. Furthermore, the process of generating and storing research samples poses the risk of affecting clinical operations and delaying patient care if not carefully executed. A cost-effective, clinic-based biorepository has been established that focuses on skin cancer samples following recommended best practices and sample validation^4,5,6.

This protocol has been developed in a dermatology clinic that performs a large volume of Mohs micrographic surgeries to remove squamous cell carcinoma (SCC), basal cell carcinoma (BCC), and melanoma skin cancers. Volunteer donors can be recruited from this patient population. It is important to establish the biorepository at the site of collection to rapidly capture tissue and blood from consented patients without delaying treatment. Gathering samples from the same clinic minimizes variations in collection techniques and minimizes variations in the quality of samples, which can be problematic for downstream applications^7,8.

The goal of the Mohs micrographic surgery technique is to ensure that all cancer tissue is removed while preserving as much healthy tissue as possible. The procedure involves the progressive removal of thin layers of tumor tissue. Each successive layer is histologically examined (after cryosectioning the tumor tissue and performing H&E staining) by a dermatologist to determine if all cancer tissue has been removed. The excision and examination of subsequent layers of tissues is executed while the patient remains in the office. This technique is considered the best treatment option for SCC⁹. At this point, the wound is closed and, to improve healing and cosmetic appearance, adjacent normal tissue (ANT) is frequently excised. Thus, this surgical procedure to remove a tumor is ideally suited for collecting histologically characterized tissue for future studies.

The procurement procedure for obtaining tumor tissue, adjacent normal tissue, saliva, and blood samples has been designed to have minimal impact on normal staff duties (Figure 1). Medical assistants perform the blood draws while preparing the patient for the procedure. After completion of the Mohs procedure, the Mohs histotechnologist prepares additional histological slides of the specimen and transfers the tissue to the biorepository. Costs associated with establishing the biorepository include the purchase of cryopreservation freezers, the creation of modest clinical laboratory space, and the development of an inventory tracking program.

Figure 1: Sequence of sample collection and responsible staff. Upon patient check-in and the attainment of patient consent, the medical assistant collects a buccal swab and performs a blood draw. The dermatologist and medical assistant then excise the tumor and close the wound, during which time SCC and ANT specimens are collected, respectively. A dedicated laboratory technician processes the blood and sections the SCC and ANT specimens for tissue culture, preservation, and entry into the biorepository. Please click here to view a larger version of this figure.

The diversity of samples collected enables a variety of experimental approaches (Figure 2). Samples collected from the patient are buccal swabs (saliva can also be collected if needed), whole blood, and excised tissue. The buccal swabs and a sample from the whole blood are saved, without processing, for genotyping and tissue matching. Whole blood is separated into white blood cell (WBC) and plasma fractions for future analyses. After Mohs processing, the frozen tumor is placed directly into liquid nitrogen and transferred to a -80 °C freezer. Fresh, viable tumor tissue and ANT samples are cultured using modifications of previous techniques^10,11 and then cryopreserved. During collection, the number of each sample type is recorded on a spreadsheet prior to entry into the inventory tracking program to facilitate accurate processing (Table 1).

Figure 2: Outline of clinic-based biorepository sample collection and processing. A buccal swab and blood sample are collected from the patient and stored for downstream genotyping and tissue matching. Whole blood is further processed for white blood cell (WBC) isolation and CTC analysis, as well as for plasma collection and liquid biopsy analysis. Tissue excised during the Mohs procedure is histologically processed for diagnostic purposes, after which the histologic slides can be used experimentally for further immunohistochemical analyses. Provided that the excised tissue sample is large enough, a portion of fresh tissue is removed and sectioned for protein and RNA isolation, and for the establishment of cultured cell lines. Please click here to view a larger version of this figure.

Collection Date:
	Patient 1	Patient 2	Patient 3	Patient 4	Patient 5
Initials and Birth Date
Eye Color
Sample Type
Sample Location
Saliva
Whole Blood
Plasma
Tumor Viable
Tissue Normal Viable
Tumor Mohs Liquid Nitrogen
Tissue Normal Liquid Nitrogen
Slides

Table 1: Checklist to record sample collections. Data tracked and recorded with each sample collected include patient initials, birth date, and eye color (for skin typing), as well as the location of specimen removal. The number of saliva samples, blood collection volumes, and the number of viable and preserved tissue specimens collected are also recorded as references for allocations to later uses. Please click here to download this file.

To validate sample collection procedures, each sample type has been tested in downstream applications. Using modifications of previous techniques¹², tumor and ANT have been successfully used in protein and RNA isolation and can potentially be used for DNA isolation. Viable explants established from the tissue sections have been evaluated by microscopy, while stored histological slides have been used for immunohistochemistry and immunofluorescence.

By following the protocol described here, it is possible to extend this model to other dermatology clinics, other tumor types (such as melanoma), and other surgical specialties and practices to provide human tissue samples for multifaceted research into human cancers. Slight modifications of this protocol are likely to be necessary for other practices but, in principle, this protocol is applicable to any surgical practice that routinely discards patient samples gathered in the course of patient treatment.

Access restricted. Please log in or start a trial to view this content.

Protocol

All experimentation on human tissue samples was approved by Western IRB (WIRB Protocol #20142461). The single criterion for the collection of tissues for these procedures is a biopsy-proven diagnosis of SCC. No exclusion criteria were outlined in the original IRB protocol, but samples from patients with a known blood-borne communicable disease were not used. Informed consent was obtained prior to the collection of cutaneous tissue, blood, and saliva. Midwestern Institutional Review Board approved the validation work with clinic-based biorepository samples at Midwestern University (AZ#807).

1. Cutaneous Tumor Tissue Processing

NOTE: This is to be performed by a Mohs histotechnologist.

1. Processing of Fresh Squamous Cell Carcinoma (SCC) Tissue for RNA and Explant Culture
   1. After the tissue has been excised by the Mohs surgeon, harvest a 10 to 50 mg (≥10 mm³) tissue sample from the center of the apical side of the tissue during relaxation (which is the process of manipulating the tissue to allow it to lie flat on the slide) before additional processing.
      ​NOTE: This is only possible if the tumor is large enough to allow a 10-50 mg-size sample (≥10 mm²) to be removed prior to the histological assessment, which is part of the Mohs procedure. If the tumor is not large enough to allow a minimum of 2 mm³ to be removed, do not proceed with processing for RNA (skip step 5).
   2. Transfer the viable tissue to a labeled 1.5 mL tube containing culture medium (1:1 mixture of DMEM:Ham's F-12, 25 mM HEPES, 100 IU/mL of penicillin, and 100 µg/mL streptomycin) using tweezers and ensure that the tissue is completely immersed in the medium. Store this tube at 4 °C before additional processing.
   3. Use the tissue for RNA isolation and expression analysis (see step 5) and/or the establishment of an explant culture (see step 6) within 24 h.
   4. Place the remainder of the tumor sample that was removed from the patient (step 1.1.1) on a cryostat tissue holder (or "chuck"). Embed the tissue in optimal cutting temperature (OCT) compound, freezing the tissue within the holder, to allow for the completion of Mohs histology and for the preparation of additional histological slides for experimental analysis.
2. Preparation of Histological Slides
   1. Cut tissue sections 7 µm thick using a cryostat and create two (or more) slides for each tumor sample. Ensure that each slide contains up to three sections of the complete tumor.
      ​NOTE: One of the two slides will be stained using H&E by the Mohs histotechnologist, and the additional slide(s) may be processed with IF, IHC, or FISH analysis.
   2. Place the slides in acetone for 1-2 s to fix the tissue. Set these slides aside to dry. Do not H&E stain or coverslip the slide to be used for future immunofluorescence (IF), immunohistochemistry (IHC), or fluorescence in situ hybridization (FISH) analysis, depending on the experimental protocol.
3. Processing of Post-Mohs Tissue
   1. Once Mohs processing has been completed (steps 1.1-1.2), work in the cryostat chamber and pry the sample from the cryo-embedding medium and place the tissue into a labeled cryogenic tube.
   2. Place the labeled vial in liquid nitrogen before the tissue has thawed. If samples are to be used for protein and/or DNA analysis, they may be transferred to liquid nitrogen or a -80 °C freezer within a few minutes to be stored for future protein expression and DNA mutation analysis (see steps 4-5).
      ​NOTE: If intact RNA is desired from the post-Mohs sample, it is essential to keep the sample frozen during the removal from the cryo-embedding medium. If extreme care is not exercised at this step, the post-Mohs sample should be reserved for protein and/or DNA analysis.
4. Processing of Fresh ANT
   1. At the time of Mohs closure, obtain ANT from the Mohs surgeon.
   2. Remove an equal or greater amount of ANT as was harvested from the SCC sample (see above) from the apical side of the normal tissue and transfer it to a labeled 1.5 mL tube containing culture medium (1:1 mixture of DMEM:Ham's F-12 supplemented with 25 mM HEPES, 100 IU/mL of penicillin, and 100 µg/mL streptomycin) using tweezers.
   3. Completely immerse the tissue in the same culture medium and store at 4 °C until subsequent processing (see steps 4-6).

2. Blood, Saliva, and Buccal Swab Processing

1. Obtain approximately 10 mL of blood in EDTA collection tubes via venipuncture.
2. Transfer the blood from the collection tubes to a sterile 15- or 50 mL centrifuge tube. Remove approximately 200 µL into a 1.5 mL cryogenic tube, avoiding bubbles; store this whole-blood sample at -80 °C, to be used for future genotyping and tissue matching, if necessary.
   1. Spin the remaining blood at 1,000 x g for 30 min and follow standard procedures to collect the plasma fraction.
   2. Aliquot the plasma into 1 mL increments in 1.5 mL cryogenic tubes and store at -80 °C for use during future liquid biopsy analyses.
3. Use a sterile swab to obtain a buccal swab sample and store the swab in a sterile tube at room temperature.
4. If needed, obtain a saliva sample and store in a sterile tube at room temperature.
   NOTE: These samples may be used for future genotyping and tissue matching, if necessary.

3. Recordkeeping of Samples

1. Transfer information from the checklist of patient samples to the biorepository database. Include patient information and diagnosis from the patient chart.
2. Print labels with a barcode for each sample and record each in the database to link each collected sample with patient data.
3. Record the distribution of the de-identified samples in the biorepository database prior to transferring the samples to the research lab.

4. Protein Isolation and Western Blot Analysis

1. Place each tissue sample (SCC and/or ANT) into a vial containing 500 µL of cell lysis buffer containing protease inhibitors per 100 mg of tissue to lyse the tissue.
   NOTE: We used a radioimmunoprecipitation assay (RIPA) buffer, composed of 50 mM Tris pH 8.0, 150 mM NaCl, 0.5% sodium deoxycholate, 1.0% NP-40, and 0.1% SDS. Other cell lysis buffers can be used.
2. Homogenize the tissues using a tissue homogenizer for 5 min in 20-s intervals at 4 °C. Spin the samples at 21,000 x g and 4 °C for 20 min and collect the supernatant containing protein into a fresh tube. Re-spin the supernatant using the same conditions and collect the final supernatant into a fresh tube.
3. Electrophorese 30-50 µg of protein from each sample using a 4-20% SDS-polyacrylamide gradient gel. Stain the gel with Coomassie Blue to visualize protein bands, if desired.
4. If Western blot analysis of expressed proteins is needed, transfer the proteins from the gel to a polyvinylidene difluoride (PVDF) membrane following standard protocols. After transfer, Ponceau stain the PVDF membrane to visualize protein bands, if desired.
5. Block the PVDF membrane and probe to detect proteins of interest following standard protocols. Use primary antibodies specific to the protein(s) of interest, along with corresponding secondary antibodies specific for the primary antibodies, at concentrations recommended by the manufacturer for Western blot analysis.
6. Expose the probed membrane using a chemiluminescent substrate and image the membrane using an imaging system.

5. RNA Isolation and Quantitative Polymerase Chain Reaction (qPCR)

1. Immediately place fresh tissue samples (SCC and/or ANT) into a 1.5 mL tube containing an RNA stabilization solution and place post-Mohs tissue samples into a 1.5 mL tube containing a frozen tissue transition solution, following the manufacturer's recommendations. Ensure that the tissue is completely immersed. Store these samples at -80 °C until use.
2. Remove the RNA samples from -80 °C and thaw on ice. Transfer the tissue to a new 1.5 mL tube containing 1 mL of RNA extraction buffer (phenol/guanidine thiocyanate) per 50-100 mg of tissue.
3. Lyse the tissues using a tissue homogenizer. Perform six cycles of homogenization, followed by a period of sample cooling; each cycle consists of 20 s of homogenization at 4 °C and a 40 s cooling period. After homogenization, incubate the sample for 5 min at room temperature.
4. Add 0.2 mL of chloroform per 1 mL of RNA extraction buffer and shake the tube vigorously by hand for 15 s. Incubate for 2-3 min at room temperature.
5. Spin the samples at 12,000 x g and 4 °C for 15 min. Remove the aqueous phase of the sample and place it into a new 1.5 mL tube.
6. Add 0.5 mL of 100% isopropanol per 1 mL of the RNA extraction buffer used in step 5.2 to the aqueous phase and incubate for 10 min at room temperature.
   NOTE: If the RNA yields are anticipated to be low (i.e., the starting tissue volume is less than 10 mg), samples may be precipitated overnight at -80 °C. Additionally, 5 µg of RNase-free glycogen per 500 µL of RNA extraction buffer may be added during the isopropanol precipitation step to improve RNA yields.
7. Spin the sample at 12,000 x g at 4 °C for 10 min. Remove the supernatant and wash the pellet with 1 mL of 75% ethanol.
8. Vortex the sample briefly and then spin it at 7,500 x g and 4 °C for 5 min. Discard the wash and air-dry the pellet for 5-10 min.
9. Resuspend the RNA pellet in 20 µL of RNase-free water.
   1. If desired, purify each RNA sample using an RNA cleanup kit following the manufacturer's recommendations.
      NOTE: Small RNAs will be lost from the sample if this step is performed.
10. Electrophorese a 1 µg sample using a 1.2% formaldehyde-MOPS agarose gel to analyze the quality of RNA.
    NOTE: As an alternative, analyze samples using a bioanalyzer to obtain an RIN number¹³.
11. Reverse-transcribe the RNA to cDNA using a reverse transcription protocol for qPCR analysis of target mRNAs (or miRNAs) of interest.

6. Tissue Explant Cultures

1. Sterilize the excised tissue prior to culture by dipping the tissue into 70% ethanol.
2. Place the tissue on a slide or dish and add enough culture medium (1:1 mixture of DMEM:Ham's F-12 supplemented with 10% FBS, 25 mM HEPES, 100 IU/mL of penicillin, and 100 µg/mL streptomycin) to cover the tissue (to prevent the tissue from drying). Carefully cut the tissue into fragments (<1 mm³) using a scalpel blade.
3. Transfer the tissue fragments to a 35-mm tissue culture dish and add approximately 20 µL of fetal bovine serum (FBS) on top of each fragment.
4. Leave the dish open in a culture hood for 20-30 min, or until almost dry.
5. Add 1 mL of culture medium (1:1 mixture of DMEM:Ham's F-12 supplemented with 10% FBS, 25 mM HEPES, 100 IU/mL of penicillin, and 100 µg/mL streptomycin) to each dish and incubate at 37 °C in 5% CO₂. Subculture or sub-clone the cultures if needed.

Access restricted. Please log in or start a trial to view this content.

Results

Tumor and ANT have been used successfully in protein isolation and tested by Western blotting. As shown in Figure 3, cutaneous squamous cell carcinoma markers (Muc1¹⁴, FHL-1¹⁵, and p40^16,17) can be detected in patient samples collected and stored in our clinic-based biorepository.

Access restricted. Please log in or start a trial to view this content.

Discussion

To the author's knowledge, this protocol is the first of its kind that focuses on the clinical procurement of cutaneous tissue samples in both a cost-effective and fast approach. Patients undergoing Mohs microsurgery are typically scheduled during specific blocks of time, and collection is limited to these periods. Sample collection involves effort from the medical assistant involved in patient care, the Mohs histotechnologist who processes the tumor samples, and a designated laboratory staff member who handles sampl...

Access restricted. Please log in or start a trial to view this content.

Materials

Name	Company	Catalog Number	Comments
BD Vacutainer Plastic Blood Collection Tubes with K3EDTA	ThermoFisher Scientific	02-685-2B
Electron Microscopy Sciences Double Edge Blades	ThermoFisher Scientific	50-949-411
Curved Medium Point General Purpose Forceps	ThermoFisher Scientific	16-100-110
Premium Microcentrifuge Tubes	ThermoFisher Scientific	05-408-138
Lonza Walkersville KGM Keratinocyte Medium	ThermoFisher Scientific	NC9791321
Electron Microscopy Sciences Tissue TEK OCT Compound	ThermoFisher Scientific	50-363-579
Leica CM1950 Cryostat	Leica Biosystems	14047743909
Frosted Microscope Slides	ThermoFisher Scientific	12-550-343
Shandon Rapid-Chrome H&E Frozen Section Staining Kit	ThermoFisher Scientific	99-900-01
Nalgene Long-Term Storage Cryogenic Tubes	ThermoFisher Scientific	03-337-7X
Falcon 15 mL Conical Centrifuge Tubes	ThermoFisher Scientific	14-959-53A
Boca Scientific BuccalT-Swab	ThermoFisher Scientific	NC9679349
Cell Signaling Technology 10x RIPA Buffer	ThermoFisher Scientific	50-195-822
Halt Protease and Phosphatase Inhibitor Cocktail	ThermoFisher Scientific	PI78443
Eppendorf 5424R Microcentrifuge	ThermoFisher Scientific	05-401-203
Pellet Morter Cordless Homogenizer	ThermoFisher Scientific	12-141-3
RNAse Free Pellet Pestle	ThermoFisher Scientific	121-141-364
Forma SteriCycle CO2 Incubator	ThermoFisher Scientific	13-998-089
HyClone Fetal Bovine Serum	ThermoFisher Scientific	SH30071.02
Gibco Advanced DMEM/F-12	ThermoFisher Scientific	12-634-028
Gibco Penicillin-Streptomycin	ThermoFisher Scientific	15140148
Gibco 1 M Hepes	ThermoFisher Scientific	15-630-130
Nunc Cell Culture 35 mm with Vent	ThermoFisher Scientific	1256591
Anti-CFH monoclonal antibody clone OX-24	Abnova	MAB12583
Anti-p40 (p63 delta) antibody	Abnova	ABX-144A
Anti MUC-1 antibody	Santa Cruz Biotech	sc-7313
Anti-Snail + Slug (phospho S246)	Abcam	Ab63568
Goat anti-rabbit IgG, Alexa Fluor 488	Invitrogen	A-11034
Alexa Fluor 568 Phallodin	Molecular Probes	A12380
ProLong Gold Antifade Mountant with DAPI	Molecular Probes	P36941
Zeiss Axio Imager Z1 Microscope with Axiocam camera	Zeiss	4300009901
Olympus IX51 phase contrast with DP72 camera	Olympus	IX511F3