an in vitro model of stretch injury in human induced pluripotent stem cell-derived neurons

An In Vitro Model of Stretch Injury in Human Induced Pluripotent Stem Cell-Derived Neurons

To stretch the plate, change the &#34;File name&#34; and the &#34;File path&#34; field in the &#34;Position Tracking&#34; virtual instrument to a unique file name and click the Run arrow. Set the depth and duration of the indentation in the &#34;Injury&#34; and &#34;Injury duration&#34; fields in the movement control panel virtual instrument. With the plate at the zero position, run the &#34;Movement Control Panel&#34; virtual instrument, and click Injure to indent the plate.
Click Top to move the stage up, clicking Stop when the plate is in the top position, and open the door to deactivate the injury device. Then, inspect the displacement history of the stage presented in the &#34;Position Tracker&#34; virtual instrument to confirm that the specified maximum displacement was applied, and export the data to an appropriate spreadsheet program.
To assess the stretch of the silicone membrane after plasma treatment, place the plate on a soft surface and prime the small protrusion on a stamp with ink from a permanent marker pen. Insert the stamp into the first well to be tested, and tap to ensure a good transfer of ink. When all of the wells have been stamped, place a high-speed camera on a boom stand over the injury device, with the lens set to the smallest numbered F-stop so that the field of view contains 12 indenters in a 3-by-4 grid.
With the plate in the zero point position, one click the Record button on the camera software so that it reads &#34;Trigger In&#34; and turn on the bright, diffuse axial light, then indent the plate as just demonstrated, and turn off the axial light.
To injure a cell culture, add 100 microliters of laminin-treated human induced pluripotent stem cell-derived neurons to each well of the plasma-treated plate, and allow the cells to attach to the plate bottom for 15 minutes at room temperature, before placing the plate in the cell culture incubator. After 2 to 3 days of culture, clamp the plate on the injury device stage and adjust the position of the lid to secure the plate without exposing the cultures to the ambient air. Then, with the plate in the zero point position, indent the plate as just demonstrated.

an-vitro-model-stretch-injury-human-induced-pluripotent-stem-cell

Research

JoVE Encyclopedia of Experiments

Neuroscience

Neuropathology

Trauma

EoE Sub Articles

eoe sub articles

1. Plate Fabrication 
<ol>
	<li>Plasma-treat a 96-well plate top with a 200 W plasma cleaner (see Table of Materials) for 60 s on high power, placing it bottom-side-up inside the plasma cleaner. Check for a purple glow visible through the window of the chamber, which indicates that an effective plasma has formed. This bonding technique is adapted from Sunkara et al.</li>
	<li>Within 60 s, place the plate top in 200 mL of 1.5% (3-Aminopropyl) triethoxysilane (APTES) in deionized (DI) water for 20 min, bottom-side-down. This solution is unstable: prepare it no more than 60 s before introducing the plate. 
	CAUTION: Work with APTES in a fume hood.</li>
	<li>Plasma treats an extracted silicone membrane in the plasma cleaner for 60 s on high power. Time the plasma treatment such that it finishes no more than 5 min before the end of the 20 min period in step 1.2.</li>
	<li>Use forceps to position the plasma treated membrane on top of a 7.5 x 11 cm2 parchment paper rectangle. Align a 7.5 cm x 11 cm x 0.5 cm aluminum slab on the lower portion of the plate fabrication clamp. Align the silicone membrane and parchment paper on the aluminum slab using forceps.</li>
	<li>Remove the plate tops from the APTES bath and shake off excess solution. Dip into a 200 mL DI water bath for 5 s and shake off excess water. Dip into a different 200 mL DI water bath for 5 s and shake off excess water. Replace the water in these baths before dipping another plate top.</li>
	<li>Use compressed air to completely dry the plate top.</li>
	<li>Place the plate top in the upper portion of the plate fabrication clamp. Gently close the plate fabrication clamp to press the plate top and silicone together. Clamp for at least 1 h.</li>
	<li>Allow the plate to cure for 24 h at room temperature before use, protected from dust.</li>
</ol>
2. Stretching a Plate
<ol>
	<li>Clean the indenters
	<ol>
		<li>Prepare a 60 W bath-style sonicator with DI water at room temperature.</li>
		<li>Support the indenter block above the sonicator bath, inverted so that only the tops of the indenters are submerged to a depth of at least 1 mm. Sonicate the indenters for 8 min at 42 kHz.</li>
		<li>Blow dry the indenters with compressed air.</li>
	</ol>
	</li>
	<li>Align the indenter block
	<ol>
		<li>Position a camera with a live feed above the stretching device so that it is looking down on the indenter array. Focus on the tops of the indenters. 
		NOTE: The setup described in Section 3, &#34;Characterizing Membrane Stretch,&#34; is one possible camera setup for this task.</li>
		<li>Secure a plate on the stage of the injury device using the stage clamps (Figure 1) and place a dome light over the device. 
		NOTE: See the Table of Materials for the instrument control software.</li>
		<li>Launch the instrument control software by clicking on the software icon on the desktop of the computer that is controlling the injury device. Run the &#34;in_vitro_neurotrauma.lvproj&#34; project by clicking on it in the launch window. From the project window, launch the motion control and position tracker virtual instruments (VIs), which are named &#39;motion_control.vi&#39; and &#39;position_tracker.vi&#39;, respectively, by double-clicking on them.</li>
		<li>Close the cage surrounding the injury device. Press the &#39;arrow&#39; button in the top left corner of the motion control VI to run the VI and click &#39;Near Bottom&#39; to lower the stage to within 2 mm of contacting the indenters. Click the &#39;Stop&#39; button to stop the VI. 
		Caution: Keep hands clear of the stretcher when manipulating the camera in the cage. The cage should be fitted with a door switch that delivers power to the stretching device only when the cage door is closed.</li>
		<li>In the project window, right click on &#39;Axis 1&#39;. Click on &#39;Interactive Test Panel&#39;. In the window that opens, set the step size to 50 &#181;m by entering &#39;500&#39; units in the &#39;Target Position&#39; field.</li>
		<li>Click the green &#39;go&#39; button at the bottom of the &#39;Interactive Test Panel&#39; window repeatedly until the plate first makes contact with any indenters. Check for contact on the live image displayed by the camera. Note the vertical stage position reported in the top left of the &#39;Interactive Test Panel&#39; window; this is the first contact position.</li>
		<li>Lower further (as described in step 2.2.6) until every well has made contact with the indenters. If necessary, move the camera to see the whole plate and move the stage up (by specifying a negative &#39;Target Position&#39;) and down. Note the vertical stage position reported in the top left of the window when all posts are in contact (this is the full contact position).</li>
		<li>Note the difference between the first contact and full contact positions. Close the &#39;Interactive Test Panel&#39;. Run the &#39;motion control VI&#39; (see step 2.2.4) and click on &#39;Top&#39; to raise the stage. Stop the motion control VI with the &#39;Stop&#39; button.</li>
		<li>Once the stage is at the top of its travel, open the door to deactivate the device. Adjust the set screws on the corners of the indenter block. Loosen the set screw on the corner that made contact first, to lower it and tighten the opposite screw to raise the corner that made contact last.</li>
		<li>Repeat the process of lowering the stage until the plate contacts the indenters, inspecting the contact images for tilt, raising the stage, and adjusting (step 2.2.9) the indenter block. When the stage and block are aligned, all indenters will make contact at once.</li>
		<li>Open the door to deactivate the device. Insert the tie-down screws into their holes on the indenter block and tighten them. Confirm that the block is level with the tie-down screws in place (steps 2.2.4-2.2.8). Take note of the stage position reported by the &#39;Interactive Test Panel&#39; when the plate makes contact. This will be the zero position for indentation experiments.</li>
	</ol>
	</li>
	<li>Lubricate the indenters
	<ol>
		<li>If the indenter block has just been set up and has not yet been lubricated, clean a solid rubber pad (7.5 cm x 11 cm x 1.5 mm) and a soft, closed-cell foam rubber pad (7.5 cm x 11 cm x 3 mm) with an ethanol-soaked lab wipe. Allow them to air dry.</li>
		<li>Soak a lab wipe in corn oil and spread it on the solid rubber pad to a dull shine.</li>
		<li>Place the foam pad onto the solid rubber pad to transfer oil to the foam pad. Place a 7.5 cm x 11 cm x 0.5 cm aluminum slab on top of the foam pad and load it with a ballast weight of approximately 360 g (e.g., 6 conical tubes loaded with 45 mL of water each) to ensure consistent transfer of oil from the solid rubber pad to the foam pad. Allow 10 s for the oil to transfer to the foam rubber pad.</li>
		<li>Move the foam rubber pad onto the indenter array. Place the aluminum slab and the ballast weight on top of it to ensure consistent transfer of the oil to the tips of the indenters. Allow 10 s for the oil to transfer to the indenters.</li>
		<li>If no plate has been stretched since the indenter block was set up and lubricated for the first time, stretch a test plate before beginning the experiment. Note: This will prevent any inconsistency between the first stretch and subsequent stretches from confounding the experiment. For subsequent stretches, repeat only steps 2.3.2-2.3.5 before each stretch.</li>
	</ol>
	</li>
	<li>Stretch a plate
	<ol>
		<li>Lubricate the indenters as described in step 2.3.</li>
		<li>Secure the plate on the stage of the injury device with the stage clamps. If sterility is required, adjust the position of the lid to secure the plate without exposing the culture surface to room air.</li>
		<li>Lower the stage to the zero-position using the &#39;motion control VI&#39; (see steps 2.2.4-2.2.6); zero-position is determined during step 2.2.</li>
		<li>Change the file name in the &#34;file path&#34; field in the &#39;position tracking VI&#39; to a unique file name, then run it with the &#39;arrow&#39; button in the top left corner of that window.</li>
		<li>Set the depth and duration of indentation (typically 1-4 mm and 30 ms, respectively, maximum depth 5 mm, minimum duration 15 ms) in the &#39;Injury (mm)&#39; and &#39;Injury Duration (ms)&#39; fields in the &#39;movement control panel VI&#39; by clicking on the fields and typing in the desired values.</li>
		<li>Run the &#39;movement control panel VI&#39; and click on &#39;Injure&#39; to indent the plate.</li>
		<li>Move the stage up to the top of its travel by clicking on &#39;Top&#39;. Then stop the VI with the &#39;Stop&#39; button and deactivate the injury device by opening the door.</li>
		<li>Inspect the displacement history of the stage presented in the &#39;position tracker VI&#39; to confirm that the specified maximum displacement was applied. Right click on the graph and click on &#39;export to Excel&#39;. Click on &#39;File| Save&#39; to save the data.</li>
	</ol>
	</li>
</ol>
3. Characterizing Membrane Stretch
<ol>
	<li>Paint the recess at the top of each indenter white to provide a high contrast background for high-speed videography. Caution: Do not paint the rims of the indenters where they make contact with plates.</li>
	<li>3D print with poly(lactic acid) (PLA), or otherwise fabricate, a cylindrical stamp with which to make a dot in each well. Make the cylinder 5.9 mm in diameter and 12.2 mm high, with a cylindrical protrusion 1.5 mm diameter and 1.0 mm high centered on top.</li>
	<li>Plasma treats the plate right-side-up to activate the silicone cell culture surface in the wells for 60 s, as mentioned in step 2.1.</li>
	<li>Place the plate on a rubber pad or other soft surface. Prime the small protrusion on the stamp (see step 1.2) with ink from a permanent marker pen. Insert the stamp into the well to be tested and tap to ensure good transfer of ink. Prime the stamp before every well.</li>
	<li>Align the indenter block and lubricate the indenters of the injury device (see steps 2.2-2.3). Clamp the plate onto the stage of the injury device. Position a bright diffuse axial light above the injury device.</li>
	<li>Set up a high-speed camera on a boom stand over the injury device, facing straight downward, with the lens set to the smallest numbered f-stop, and turn it on. Launch the camera software on the computer connected to the camera. In the frame rate drop down menu, select 2,000 frames per second, and in the shutter drop down menu, select the fastest exposure time which yields high contrast images. Center over the dotted wells. &#8203;
	<ol>
		<li>Position the camera so that the field of view contains 12 wells in a 3 x 4 grid. 
		NOTE: This field of view offers an optimal compromise between throughput and resolution for a 1,280 &#215; 1,024 image.</li>
	</ol>
	</li>
	<li>Lower the plate to the zero-point (see steps 2.2.4-2.2.6). One-click the record button on the camera software so that it reads &#39;trigger in&#39;. Initiate the position tracker VI (step 2.4.4).</li>
	<li>Turn on the bright diffuse axial light. Indent the plate as described in step 2.4.6.</li>
	<li>Turn off the bright diffuse axial light.</li>
	<li>On the camera control computer, find the 30-40 ms window of the recording in which the indentation occurs: drag the beginning and end arrows in the high-speed video play bar in the camera software. Click Save, set the name in the &#39;File Name&#39; field, select &#39;TIFF&#39; in the &#39;Format&#39; field, and click on &#39;Save&#39;.
	<ol>
		<li>Look through the .TIF-files for images of the least stretched (beginning) and most stretched (peak indentation) states.</li>
		<li>To measure the height and width of the dots in both images, use Fiji to open the images of the least and peak stretch side-by-side. Using the default rectangular selection tool, click and drag to draw a box around a dot in the least stretch image. Measure the height and width with &#39;Analyze| Measure&#39;.</li>
		<li>Repeat for the dot in the same well on the peak stretch image. Repeat for the rest of the wells.</li>
	</ol>
	</li>
	<li>Calculate the Lagrangian strain in the x and y directions as follows: 
	<img alt="Equation 1" src="/files/ftp_upload/23013/23013_equation1.jpg" style="margin: auto;" /> 
	NOTE: Here, Exx is the Lagrangian strain in the x direction, Eyy is the Lagrangian strain in the y direction, X is the width of the dot, Y is the height of the dot, f denotes the final image (i.e., the peak indentation image), and i denotes the initial image (i.e., the pre-indentation image). Average the two values to determine the strain in that well.</li>
</ol>
4. Plating the Cultured Cells 
<ol>
	<li>Autoclave the bins and ballast weights that will be used for sterilization.</li>
	<li>Plasma treat the silicone-bottomed plates right-side-up for 60 s (see step 1.1). Immediately submerge the plates in sterile bins containing 70% ethanol for 15 min.</li>
	<li>Submerge the plates in sterile phosphate buffered saline (PBS) in separate sterile bins for 30 min.</li>
	<li>Aspirate the PBS from the wells. Only dry one plate at a time to prevent the wells from losing the plasma treatment. 
	Caution: Silicone bottomed plates provide less tactile feedback than rigid plates when pipetting and are more likely to block the tip of a pipette.</li>
	<li>Add 100 &#181;L of 0.1 mg/mL poly-L-ornithine (PLO) per well to the sterilized plates. Incubate at room temperature for 1 h.</li>
	<li>Rinse the wells twice with 100 &#181;L sterile PBS, leaving the second wash on the wells until the cell suspension is ready.</li>
	<li>Remove the vial of hiPSCNs from liquid nitrogen storage using safety gloves and place on dry ice. Quickly transport the vial to a 37 &#176;C water bath and thaw for exactly 3 min. Do not swirl the vial.</li>
	<li>In a sterile hood, gently transfer the contents of the vial to a 50 mL conical tube using a 1 mL serological pipette.</li>
	<li>Rinse the empty cryogenic vial with 1 mL of room temperature complete maintenance medium (media base + supplement).</li>
	<li>Transfer the 1 mL of media into the 50-mL tube dropwise at about one drop per second. Gently swirl the tube while adding. Add 8 mL of room temperature complete maintenance medium to the 50 mL tube at about 2 drops/s.</li>
	<li>Cap the tube and invert 2-3 times. Count the cells with a hemocytometer. Compute the volume of the additional media required to dilute the cell suspension to 225,000 cells/mL.</li>
	<li>Gently pipette the amount of media (calculated above) into the tube of cell suspension using a 25 mL serological pipette.</li>
	<li>Add 10 &#181;L of 1 mg/mL laminin stock per 1 mL of cell suspension with a 1,000 &#181;L micropipette to achieve 10 &#181;g/mL of laminin in the cell suspension. Aspirate up and down once with the tip used for laminin, then cap the tube and invert the tube once.</li>
	<li>Aspirate the PBS from the plates, one plate at a time. Use a multichannel pipette to add 100 &#181;L of the hiPSCN cell suspension to each well. The wells have a culture area of 0.33 cm2, so the cell density per area is 67,500 cells/cm2.</li>
	<li>Rest the plates at room temperature for 15 min after seeding to promote attachment. To avoid fan vibrations of sterile culture hood, place the covered plates on the lab bench. Incubate the cultures at 37 &#176;C with 5% CO2.</li>
	<li>Perform a full media change at 24 h, refilling the wells with 200 &#181;L of complete maintenance media. Perform a half media change of 100 &#181;L/ well every 2-3 days.</li>
</ol>
5. Injuring Cultures 
<ol>
	<li>Align the indenter block and find the zero position as described in step 2.2. Lubricate the indenters as described in step 2.3.</li>
	<li>Set the filename for the displacement history in the &#39;position tracker VI&#39; (step 2.4.4). Set the injury parameters in the &#39;motion control VI&#39; (step 2.4.5).</li>
	<li>Take the plate to be injured out of the incubator and clamp it onto the stage. Adjust the position of the lid to secure the plate without exposing the cultures to room air.</li>
	<li>Lower the plate to the zero-point (steps 2.2.4-2.2.6) using the &#39;motion control VI&#39;. Start the &#39;position tracker VI&#39; (step 2.4.4).</li>
	<li>Use the movement control VI to indent the plate (as described in step 2.4.6). For sham stretches, skip only this step.</li>
	<li>Return the stage to the top of its range of motion (see step 2.4.7). Return the plate to the incubator.</li>
	<li>Inspect and save the displacement trace (as in step 2.4.8).</li>
</ol>

<table border="1" fo:keep-together.within-page="1" fo:keep-with-next.within-page="always">
	<tbody>
		<tr>
			<td>.010&#34; Silicone Sheet</td>
			<td>Specialty Manufacturing, Inc&#160;</td>
			<td>#70P001200010</td>
			<td>Polydimethylsiloxane (PDMS) sheet</td>
		</tr>
		<tr>
			<td>Sparkleen</td>
			<td>Fisher Scientific</td>
			<td>#043204</td>
			<td></td>
		</tr>
		<tr>
			<td>Nunc 256665</td>
			<td>Fisher Scientific</td>
			<td>#12-565-600</td>
			<td>Bottomless 96 Well Plate</td>
		</tr>
		<tr>
			<td>Kim Wipes</td>
			<td>ULINE</td>
			<td>S-8115</td>
			<td></td>
		</tr>
		<tr>
			<td>Plasma Cleaner</td>
			<td>Harrick Plasma</td>
			<td>#PDC-001-HC</td>
			<td></td>
		</tr>
		<tr>
			<td>(3-Aminopropyl) triethoxysilane</td>
			<td>Sigma-Aldrich</td>
			<td>#440140</td>
			<td>APTES</td>
		</tr>
		<tr>
			<td>Parchment Paper</td>
			<td>Reynolds</td>
			<td>N/A</td>
			<td></td>
		</tr>
		<tr>
			<td>Dome Light</td>
			<td>CCS inc</td>
			<td>LFX2-100SW</td>
			<td></td>
		</tr>
		<tr>
			<td>Dome Light Power Supply</td>
			<td>CCS inc</td>
			<td>PSB-1024VB</td>
			<td></td>
		</tr>
		<tr>
			<td>Axial Diffuse Lighting Unit</td>
			<td>Siemens</td>
			<td>Nerlite DOAL-75-LED</td>
			<td>Diffuse axial light</td>
		</tr>
		<tr>
			<td>High Power LED Array</td>
			<td>CREE</td>
			<td>XLamp CXA2540</td>
			<td>High Power LED Array</td>
		</tr>
		<tr>
			<td>LED holder</td>
			<td>Molex</td>
			<td>1807200001</td>
			<td>LED Holder</td>
		</tr>
		<tr>
			<td>LED power supply</td>
			<td>Mean Well</td>
			<td>HLG-320H-36B</td>
			<td>Constant Current Power Supply</td>
		</tr>
		<tr>
			<td>FastCam Viewer software</td>
			<td>Photron</td>
			<td></td>
			<td>camera softeware</td>
		</tr>
		<tr>
			<td>Fastcam Mini UX50</td>
			<td>Photron</td>
			<td>N/A</td>
			<td>High Speed Camera</td>
		</tr>
		<tr>
			<td>Micro-NIKKOR 105mm f/2.8</td>
			<td>Nikon</td>
			<td>#1455</td>
			<td>High Speed Camera Lens</td>
		</tr>
		<tr>
			<td>0.1 mg/mL Poly-L-Ornithine</td>
			<td>Sigma-Aldrich</td>
			<td>#P4597</td>
			<td></td>
		</tr>
		<tr>
			<td>iCells</td>
			<td>Cellular Dynamics International</td>
			<td>#NRC-100-010-001</td>
			<td></td>
		</tr>
		<tr>
			<td>iCell media</td>
			<td>Cellular Dynamics International</td>
			<td>#NRM-100-121-001</td>
			<td></td>
		</tr>
		<tr>
			<td>iCell supplement</td>
			<td>Cellular Dynamics International</td>
			<td>#NRM-100-031-001</td>
			<td></td>
		</tr>
		<tr>
			<td>Laminin</td>
			<td>Sigma-Aldrich</td>
			<td>#L2020</td>
			<td></td>
		</tr>
		<tr>
			<td>voice coil actuator</td>
			<td>BEI Kimco</td>
			<td>LA43-67-000A</td>
			<td></td>
		</tr>
		<tr>
			<td>optical linear encoder</td>
			<td>Renishaw</td>
			<td>T1031-30A</td>
			<td></td>
		</tr>
		<tr>
			<td>servo drive</td>
			<td>Copley Controls</td>
			<td>Xenus XTL</td>
			<td></td>
		</tr>
		<tr>
			<td>Controller</td>
			<td>National Instruments</td>
			<td>cRIO 9024 Real Time PowerPC Controller</td>
			<td></td>
		</tr>
		<tr>
			<td>cRIO chassis</td>
			<td>National Instruments</td>
			<td>cRIO 9113</td>
			<td></td>
		</tr>
		<tr>
			<td>digital input module</td>
			<td>National Instruments</td>
			<td>NI 9411</td>
			<td></td>
		</tr>
		<tr>
			<td>data acquistion chassis</td>
			<td>National Instruments</td>
			<td>NI 9113</td>
			<td></td>
		</tr>
		<tr>
			<td>LabVIEW</td>
			<td>National Instruments</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>hiPSCNs</td>
			<td>Cellular Dynamics International</td>
			<td></td>
			<td></td>
		</tr>
	</tbody>
</table>

Source: Phillips, J. K. et al. <a href="https://app.jove.com/v/57305">Method for High Speed Stretch Injury of Human Induced Pluripotent Stem Cell-derived Neurons in a 96-well Format.</a> J. Vis. Exp. (2018)
This video demonstrates the process of inducing stretch injury on human induced pluripotent stem cell-derived neurons (hiPSCNs). The cells are taken in a bottomless multi-well plate with a silicone membrane attached. Controlled mechanical stress is applied on the membrane to induce cytoskeletal disruption and cell membrane damage, inducing a stretch injury phenotype in the cells.

<img alt="Figure 1" src="/files/ftp_upload/23013/23013_Figure1.jpg" /> 
Figure 1: A labeled schematic of the injury device.&#160;(A) Top view, (B) isometric view, (C) front view, (D) right side view. The scale bar applies to the orthographic views (A, B and D).

1. Plate Fabrication 

	Plasma-treat a 96-well plate top with a 200 W plasma cleaner (see Table of Materials) for 60 s on high power, placing it ...

Begin with a multi-well bottomless plate attached to a silicone membrane. The membrane is coated with a biopolymer to facilitate cell adhesion.
Introduce human induced pluripotent stem cell-derived neurons, or hiPSCNs, suspended in a medium into the wells. The medium is supplemented with extracellular matrix, or ECM proteins to enhance cell adhesion.
Incubate the plate, allowing the cells to adhere to the ECM proteins and biopolymer, promoting uniform interaction with the membrane surface.
Next, secure the plate on the stage of an injury device.
Using the device, apply indentation on the membrane to generate controlled mechanical stress on the neurons.
The stress disrupts the cytoskeleton, which causes the degeneration of cellular protrusions termed neurites and the formation of small swellings along the neurites.
The stress also damages the cell membrane integrity, resulting in cell death.
The hiPSCNs exhibiting a stretch injury phenotype are now ready for analysis.

27 Görüntüleme. İnsan Kaynaklı Pluripotent Kök Hücre Kaynaklı Nöronlarda İn Vitro Gerilme Yaralanması Modeli

Video: İnsan Kaynaklı Pluripotent Kök Hücre Kaynaklı Nöronlarda İn Vitro Gerilme Yaralanması Modeli - Deney

Controlled Cortical Impact Model of Mouse Brain Injury with Therapeutic Transplantation of Human Induced Pluripotent Stem Cell-Derived Neural Cells

Traumatic brain injury (TBI) is a leading cause of morbidity and mortality worldwide. Disease pathology due to TBI progresses from the primary mechanical insult to secondary injury processes, including apoptosis and inflammation. Animal modeling has been valuable in the search to unravel injury mechanisms and evaluate potential neuroprotective therapies. This protocol describes the controlled cortical impact (CCI) model of focal, open-head TBI. Specifically, parameters for producing a mild unilateral cortical injury are described. Behavioral consequences of CCI are analyzed using the adhesive tape removal test of bilateral sensorimotor integration. Regarding experimental therapy for TBI pathology, this protocol also illustrates a process for transplanting cultured cells into the brain. Neural cell cultures derived from human induced pluripotent stem cells (hiPSCs) were chosen for their potential to show superior functional restoration in human TBI patients. Chronic survival of hiPSCs in the host mouse brain tissue is detected using a modified DAB immunohistochemical process.

This protocol demonstrates methodologies for a mouse model of open-skull traumatic brain injury and transplantation of cultured human induced pluripotent stem cell-derived cells into the injury site. Behavioral and histologic tests of outcomes from these procedures are also described in brief.

Insan kaynaklı pluripotent kök hücre türetilen nöral hücrelerin terapötik transplantasyonu ile fare beyin yaralanması kontrollü Kortiik darbe modeli

Traumatic brain injury (TBI) is a leading cause of morbidity and mortality worldwide. Disease pathology due to TBI progresses from the primary mechanical ...

JoVE Journal

Gelişim Biyolojisi

Human Saphenous Vein Endothelial Cell Isolation and Exposure to Controlled Levels of Shear Stress and Stretch

Coronary artery bypass graft (CABG) surgery is a procedure to revascularize ischemic myocardium. Saphenous vein remains used as a CABG conduit despite the reduced long-term patency compared to arterial conduits. The abrupt increase of hemodynamic stress associated with the graft arterialization results in vascular damage, especially the endothelium, that may influence the low patency of the saphenous vein graft (SVG). Here, we describe the isolation, characterization, and expansion of human saphenous vein endothelial cells (hSVECs). Cells isolated by collagenase digestion display the typical cobblestone morphology and express endothelial cell markers CD31 and VE-cadherin. To assess the mechanical stress influence, protocols were used in this study to investigate the two main physical stimuli, shear stress and stretch, on arterialized SVGs. hSVECs are cultured in a parallel plate flow chamber to produce shear stress, showing alignment in the direction of the flow and increased expression of KLF2, KLF4, and NOS3. hSVECs can also be cultured in a silicon membrane that allows controlled cellular stretch mimicking venous (low) and arterial (high) stretch. Endothelial cells' F-actin pattern and nitric oxide (NO) secretion are modulated accordingly by the arterial stretch. In summary, we present a detailed method to isolate hSVECs to study the influence of hemodynamic mechanical stress on an endothelial phenotype.

We describe a protocol to isolate and culture human saphenous vein endothelial cells (hSVECs). We also provide detailed methods to produce shear stress and stretch to study mechanical stress in hSVECs.

İnsan safen ven endotel hücre izolasyonu ve kontrollü kayma stresi ve gerilme seviyelerine maruz kalma

Coronary artery bypass graft (CABG) surgery is a procedure to revascularize ischemic myocardium. Saphenous vein remains used as a CABG conduit despite the ...

Tıp

Automated Production of Human Induced Pluripotent Stem Cell-Derived Cortical and Dopaminergic Neurons with Integrated Live-Cell Monitoring

Manual culture and differentiation protocols for human induced pluripotent stem cells (hiPSC) are difficult to standardize, show high variability and are prone to spontaneous differentiation into unwanted cell types. The methods are labor-intensive and are not easily amenable to large-scale experiments. To overcome these limitations, we developed an automated cell culture system coupled to a high-throughput imaging system and implemented protocols for maintaining multiple hiPSC lines in parallel and neuronal differentiation. We describe the automation of a short-term differentiation protocol using Neurogenin-2 (NGN2) over-expression to produce hiPSC-derived cortical neurons within 6&#8210;8 days, and the implementation of a long-term differentiation protocol to generate hiPSC-derived midbrain dopaminergic (mDA) neurons within 65 days. Also, we applied the NGN2 approach to a small molecule-derived neural precursor cells (smNPC)&#160;transduced with GFP lentivirus and established a live-cell automated neurite outgrowth assay. We present an automated system with protocols suitable for routine hiPSC culture and differentiation into cortical and dopaminergic neurons. Our platform is suitable for long term hands-free culture and high-content/high-throughput hiPSC-based compound, RNAi and CRISPR/Cas9 screenings to identify novel disease mechanisms and drug targets.

We show the automation of human induced pluripotent stem cell (hiPSC) cultures and neuronal differentiations compatible with automated imaging and analysis.

Entegre Canlı Hücre İzleme ile İnsan Kaynaklı Pluripotent Kök Hücre Kaynaklı Kortikal ve Dopaminerjik Nöronların Otomatik Üretimi

Manual culture and differentiation protocols for human induced pluripotent stem cells (hiPSC) are difficult to standardize, show high variability and are ...

An In Vitro Model of Stretch Injury in Human Induced Pluripotent Stem Cell-Derived Neurons

TRANSKRIPT

An In Vitro Model of Stretch Injury in Human Induced Pluripotent Stem Cell-Derived Neurons