This work was supported by the Israel Science Foundation, grant # 306/15.

1. System Preparation
<ol>
	<li>Fill the tank with tap water up to a depth of about 20 cm to satisfy deep-water condition; clean the water surface of any contaminants that may affect the surface tension.</li>
	<li>Position the instrument carriage at the desired fetch.
	<ol>
		<li>Mount the Pitot tube and position it at the center of the airflow part of the test section.</li>
		<li>Mount the wave gauge on a computer-controlled vertical stage to enable its static calibration.</li>
	</ol>
	</li>
	<li>Position the LSG asse...

<ol>
	<li>Sir William Thomson, F. R. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Hydrokinetic+solutions+and+observations.">Hydrokinetic solutions and observations.</a> Philosophical Magazine. 42, 362-377 (1871).</li><li>Jeffreys, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=On+the+formation+of+water+waves+by+wind.">On the formation of water waves by wind.</a> Proc. Roy. Soc. London Ser. A. 107, 189-206 (1925).</li><li>Miles, J. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=On+the+generation+of+surface+waves+by+shear+flows.">On the generation of surface waves by shear flows.</a> J. Fluid Mech. 3 (2), 185-204 (1957).</li><li>Phillips, O. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=On+the+generation+of+waves+by+turbulent+wind.">On the generation of waves by turbulent wind.</a> J. Fluid Mech. 2 (5), 417-445 (1957).</li><li>Plate, E. J., Chang, P. C., Hidy, G. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Experiments+on+the+generation+of+small+water+waves+by+wind.">Experiments on the generation of small water waves by wind.</a> J. Fluid Mech. 35 (4), 625-656 (1969).</li><li>Mitsuyasu, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=On+the+growth+of+the+spectrum+of+wind-generated+waves+I.">On the growth of the spectrum of wind-generated waves I.</a> Rep. Res. Inst. Appl. Mech., Kyushu Univ. 16 (55), 459-482 (1968).</li><li>Toba, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Local+balance+in+the+air-sea+boundary+processes,+I.+On+the+growth+process+of+wind+waves.">Local balance in the air-sea boundary processes, I. On the growth process of wind waves.</a> J. Oceanog. Soc. Japan. 28, 109-120 (1972).</li><li>Toba, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Local+balance+in+the+air-sea+boundary+processes.+III.+On+the+spectrum+of+wind+waves.">Local balance in the air-sea boundary processes. III. On the spectrum of wind waves.</a> J. Oceanogr. Soc. Japan. 29, 209-220 (1973).</li><li>Hara, T., Bock, E. J., Donelan, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Frequency-wavenumber+spectrum+of+wind-generated+gravity-capillary+waves.">Frequency-wavenumber spectrum of wind-generated gravity-capillary waves.</a> J. Geoph. Res. 102, 1061-1072 (1997).</li><li>Caulliez, G., Gu&#233;rin, C. -. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Higher-order+statistical+analysis+of+short+wind+wave+fields.">Higher-order statistical analysis of short wind wave fields.</a> J. Geophys. Res. 117, C06002 (2012).</li><li>Mitsuyasu, H., Rikiishi, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+growth+of+duration-limited+wind+waves.">The growth of duration-limited wind waves.</a> J. Fluid Mech. 85, 705-730 (1978).</li><li>Kawai, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Generation+of+initial+wavelets+by+instability+of+a+coupled+shear+flow+and+their+evolution+to+wind+waves.">Generation of initial wavelets by instability of a coupled shear flow and their evolution to wind waves.</a> J. Fluid Mech. 93 (4), 661-703 (1979).</li><li>Waseda, T., Toba, Y., Tulin, M. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Adjustment+of+wind+waves+to+sudden+changes+of+wind+speed.">Adjustment of wind waves to sudden changes of wind speed.</a> J. Oceanography. 57, 519-533 (2001).</li><li>Uz, B. M., Hara, T., Bock, E. J., Donelan, M. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Laboratory+observations+of+gravity-capillary+waves+under+transient+wind+forcing.">Laboratory observations of gravity-capillary waves under transient wind forcing.</a> J. Geophys. Res.: Oceans. 108 (C2), (2003).</li><li>Hwang, P. A., Wang, D. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Field+measurements+of+duration-limited+growth+of+wind-generated+ocean+surface+waves+at+young+stage+of+development.">Field measurements of duration-limited growth of wind-generated ocean surface waves at young stage of development.</a> J. Phys. Oceanogr. 34 (10), 2316-2326 (2004).</li><li>Hwang, P. A., Garc&#237;a-Nava, H., Ocampo-Torres, F. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Observations+of+wind+wave+development+in+mixed+seas+and+unsteady+wind+forcing.">Observations of wind wave development in mixed seas and unsteady wind forcing.</a> J. Phys. Oceanogr. 41, 2340-2359 (2011).</li><li>Liberzon, D., Shemer, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Experimental+study+of+the+initial+stages+of+wind+waves'+spatial+evolution.">Experimental study of the initial stages of wind waves' spatial evolution.</a> J. Fluid Mech. 681, 462-498 (2011).</li><li>Miles, J. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=On+generation+of+surface+waves+by+shear+flows.+Part+2.">On generation of surface waves by shear flows. Part 2.</a> J. Fluid Mech. 6 (4), 568-582 (1959).</li><li>Plant, W. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+relationship+between+wind+stress+and+wave+slope.">A relationship between wind stress and wave slope.</a> J. Geophys. Res. 87, 1961-1967 (1982).</li><li>Zavadsky, A., Shemer, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Characterization+of+turbulent+air+flow+over+evolving+water-waves+in+a+wind-wave+tank.">Characterization of turbulent air flow over evolving water-waves in a wind-wave tank.</a> J. Geophys. Res. 117, C00J19 (2012).</li><li>Zavadsky, A., Liberzon, D., Shemer, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Statistical+analysis+of+the+spatial+evolution+of+the+stationary+wind+wave+field.">Statistical analysis of the spatial evolution of the stationary wind wave field.</a> J. Phys. Oceanogr. 43, 65-79 (2013).</li><li>Zavadsky, A., Benetazzo, A., Shemer, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=On+the+two-dimensional+structure+of+short+gravity+waves+in+a+wind+wave+tank.">On the two-dimensional structure of short gravity waves in a wind wave tank.</a> Phys. Fluids. 29 (1), 016601 (2017).</li><li>Zavadsky, A., Shemer, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Investigation+of+statistical+parameters+of+the+evolving+wind+wave+field+using+Laser+Slope+Gauge.">Investigation of statistical parameters of the evolving wind wave field using Laser Slope Gauge.</a> Phys. Fluids. 29 (5), (2017).</li><li>Zavadsky, A., Shemer, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Water+waves+excited+by+near-impulsive+wind+forcing.">Water waves excited by near-impulsive wind forcing.</a> J. Fluid Mech. , (2017).</li></ol>

The present experimental protocol is aimed at quantitative characterization of a wave field under unsteady wind forcing that evolves in time and space. Since wind-waves are essentially random and three-dimensional, and thus vary quickly in time and space, records of individual realizations of a growing wind-wave field under time-dependent wind forcing can only provide qualitative estimates of the governing wave parameters. To achieve the goal of this protocol and obtain statistically reliable time- and fetch-dependent wa...

Since ancient times, it has been well known that waves on water surfaces are excited by wind. The current understanding of the physical mechanisms that govern this process is far from satisfactory. Numerous theories attempting to describe wind-wave generation were proposed over the years1,2,3,4, however their reliable experimental validation is not yet available. Measurements of random wind-waves in the ocean are extremely challenging due to unpredictable wind that may vary quickly in direction as well as in magnitude. Laboratory experiments have the advantage of controllable conditions that enable prolonged and repeatable measurements.
Under steady wind forcing in the laboratory environment, wind-waves evolve in space. Early laboratory experiments on waves under steady forcing performed decades ago were limited to instantaneous surface elevation measurements5,6,7,8. More recent studies also employed various optical techniques to measure instantaneous water surface inclination angle, such as LSG9,10. Those measurements allowed getting some limited qualitative information on the three-dimensional structure of wind-wave fields. When wind forcing is unstable, as it is in field experiments, additional complexity is introduced to the problem of water waves&#39; excitation by wind, since the statistical parameters of the resulting wave field vary not just in space but in time as well. The attempts made so far to describe wave evolution patterns qualitatively and quantitatively under time-dependent forcing were only partially successful11,12,13,14,15,16. The relative contribution of different plausible physical mechanisms that may lead to excitation and growth of waves due to wind action remains largely unknown.
Our experimental facility was designed with the purpose of enabling the accumulation of accurate and diverse statistical information on the variation of wind-wave field characteristics under either steady or unsteady wind forcing. Two major factors facilitated carrying out these detailed studies. First, the modest size of the facility results in relatively short characteristic evolution scales in time and space. Second, the whole experiment is fully controlled by a computer, thus enabling the performance of experimental runs under different experimental conditions automatically and practically without human intervention. These features of the experimental set-up are of crucial importance in performing experiments on waves excited from rest by impulsive wind.
Spatial growth of wind-waves under steady forcing has been studied in our facility for a range of wind velocities17. Results were compared with growth rate estimates based on the Miles18 theory as presented by Plant19. The comparison revealed that the experimental results differ notably from the theoretical predictions. Additional important parameters were also obtained in17, such as mean pressure drop in the test section, as well as the absolute values and phases of characteristic static pressure fluctuations. The shear stress at the air-water interface is essential for characterization of momentum and energy transfer between wind and waves17,19. Therefore, detailed measurements of the logarithmic boundary layer and the turbulent fluctuations in the air flow above water waves were performed at numerous fetches and wind velocities20. The values of the friction velocity u* at the air-water interface determined in this study were used to obtain dimensionless statistical parameters of the wind-waves measured in our facility21. These values were compared with the corresponding dimensionless parameters obtained in larger experimental installations and field experiments. It was demonstrated previously21 that with proper scaling, the important characteristics of the wind-wave field obtained in our small-scale facility do not differ significantly from the corresponding data accumulated in larger laboratory installations and open sea measurements. These parameters include spatial growth of the representative wave height and wave length, the shape of the frequency spectrum of the surface elevation, as well as the values of higher statistical moments.
The subsequent studies carried out in our facility22,23 showed that wind waves are essentially random and three-dimensional. To get a better insight into the 3D structure of wind waves, an attempt was made to perform quantitative time-dependent measurements of water surface elevation over an extended area using stereo video imaging22. Due to inadequate computer power available at present and processing algorithms that are not yet sufficiently effective, these attempts proved to be only partially successful. However, it was demonstrated that combined use of a conventional capacitance-type wave gauge and the LSG provides valuable information on the spatial structure of wind waves. Simultaneous application of both those instruments enables independent measurements with high temporal resolution of the instantaneous surface elevation and of the two components of the instantaneous surface slope23. These measurements allow estimation of both the dominant frequency and dominant wave length of the waves, as well as providing insight into the wave structure in the direction normal to the wind. A pitot tube, which can be moved vertically by a computer-controlled motor, complements the set of sensors and is used for measurements of wind velocity.
All those studies made clear that randomness and three-dimensionality of wind waves result in significant variability of the measured parameters even for steady wind forcing and a single measuring location. Thus, prolonged measurements with duration commensurate with the characteristic time scales of the measured wave field are needed to accumulate sufficient information for extracting reliable statistical quantities. To gain valuable physical insight into the mechanisms governing spatial variation of the wave field, it is imperative to carry out measurements at numerous locations and for as many values of the wind flow rate as possible in the test section. To achieve this goal, it is thus highly desirable to apply an automated experimental procedure.
Experiments on waves excited by unsteady wind forcing introduce an additional level of complexity. In such studies, it is imperative to relate the instantaneous measured parameters to the instantaneous level of the wind speed. Consider experiments on waves excited from rest by a nearly impulsive wind forcing as an important example. In this case, numerous independent measurements are needed of the wind-wave field evolving under the action of wind that varies in time following the same prescribed pattern24. Meaningful statistical parameters, expressed as a function of time elapsed since the initiation of air flow, are then calculated by averaging the data extracted from the accumulated ensemble of independent realizations. This undertaking may involve tens and hundreds of hours of continuous sampling. The total duration of experimental sessions required to accomplish such an ambitious task renders the whole approach unfeasible, unless the experiment is fully automated. No such fully computerized experimental procedure in wind-wave facilities has been developed until recently. That is among the main reasons for the lack of reliable statistical data on wind waves under unsteady forcing.
Since the facility used for the experiment is not constructed from commercially available, off-the-shelf hardware, a brief description of its main parts is provided here.
<img alt="Figure 1" class="xfigimg" src="/files/ftp_upload/56480/56480fig1.jpg" /> 
Figure 1. Schematic (not to scale) view of the experimental facility. 1 - blower; 2 - inflow settling chamber; 3 - outflow settling chamber; 4 - silencer boxes; 5 - test section; with a 6 - beach; 7 - heat exchanger; 8 - honeycomb; 9 - nozzle; 10 - wavemaker; 11 - flap; 12 - instrument carriage; 13 - wave gauge driven by a stepper motor; 14 - Pitot tube driven by a stepper motor. <a href="http://cloudflare.jove.com/files/ftp_upload/56480/56480fig1large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
The experimental facility consists of a closed loop wind tunnel mounted over a wave tank (a schematic view is shown in Figure 1). The test section is 5 m long, 0.4 m wide, and 0.5 m deep. The sidewalls and floor are made of 6 mm thick glass plates and are enclosed within a frame made of aluminum profiles. A 40-cm long flap provides a smooth expansion of the airflow cross-section from the nozzle to the water surface. Wave energy absorbing beach made of porous packing material is located at the far end of the tank. A computer-controlled blower allows attaining mean air flow velocity in the test section up to 15 m/s.
The custom-made capacitance-type 100 mm-long wave gauge is made of anodized tantalum. 0.3 mm wire is mounted on a vertical stage driven by a PC-controlled step motor designed for wave gauge calibration. A Pitot tube with a diameter of 3 mm is used for measuring the dynamic pressure in the central airflow part of the test section.
The LSG, measuring instantaneous 2D water surface slope, is installed on a frame detached from the test section that can be positioned at any location along the tank (Figure 2). LSG consists of four main parts: a laser diode, a Fresnel lens, a diffusive screen, and a Position Sensing Detector (PSD) assembly. The laser diode generates a 650 nm (red), 200 mW focusable laser beam with diameter of about 0.5 mm. The 26.4 cm diameter Fresnel lens with focal length of 22.86 cm directs the incoming laser beam to the 25 x&#160;25 cm2 diffusive screen located in the back focal plane of the lens.
<img alt="Figure 2" class="xfigimg" src="/files/ftp_upload/56480/56480fig2.jpg" /> 
Figure 2. Schematic view of the Laser Slope Gauge (LSG). 1 - laser diode; 2 - Fresnel lens; 3 - diffusive screen; 4 - Position Sensor Detector (PSD). <a href="http://cloudflare.jove.com/files/ftp_upload/56480/56480fig2large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
This protocol describes the procedure that allows performing experiments in which numerous parameters characterizing unsteady waves are measured simultaneously under time-dependent wind forcing. The procedure can be adjusted to any desired dependence of wind velocity on time that can be attained in view of the technical limitations of the experimental facility. The present protocol describes specifically experiments in which in every realization, wind starts nearly impulsively over initially calm water. The steady wind forcing then lasts for long enough that the wind-wave field everywhere in the test section attains quasi-steady state. The wind eventually is shut down, again nearly impulsively. At all stages, multiple wave parameters are recorded. The procedure that allows computation of numerous statistically representative ensemble-averaged quantities characterizing the instantaneous local wind-wave field is novel, and was developed in the course of recent experiments carried out in our facility22,23,24.

<table>
	<tbody>
		<tr>
			<td>PSD</td>
			<td>THORLABS</td>
			<td>PDP90A</td>
			<td></td>
		</tr>
		<tr>
			<td>Laser Diode</td>
			<td></td>
			<td></td>
			<td>any laser pointer &#8804; 200 mW</td>
		</tr>
		<tr>
			<td>Aspheric Fresnel Lens</td>
			<td>EDMUND OPTICS</td>
			<td>#46-390</td>
			<td>Diameter 10.4&#39;&#39;, Focal length 9&#39;&#39;</td>
		</tr>
		<tr>
			<td>Wave-gauge</td>
			<td></td>
			<td></td>
			<td>custom made</td>
		</tr>
		<tr>
			<td>Pressure Transducer</td>
			<td>MAMAC SYSTEMS</td>
			<td>PR-274-R2-VDC</td>
			<td></td>
		</tr>
		<tr>
			<td>Signal Conditioner</td>
			<td></td>
			<td></td>
			<td>custom made</td>
		</tr>
		<tr>
			<td>Diffusive screen</td>
			<td>EDMUND OPTICS</td>
			<td>#02-147</td>
			<td></td>
		</tr>
		<tr>
			<td>Water tank</td>
			<td></td>
			<td></td>
			<td>custome made</td>
		</tr>
		<tr>
			<td>A/D card PCI-6221</td>
			<td>National Instruments</td>
			<td>779066-01</td>
			<td></td>
		</tr>
		<tr>
			<td>Pitot tube</td>
			<td>KIMO Instruments</td>
			<td>12971</td>
			<td></td>
		</tr>
		<tr>
			<td>15&#176; Nom. VIS-NIR Coated, Wedge Prism</td>
			<td>EDMUND OPTICS</td>
			<td>#47-624</td>
			<td></td>
		</tr>
		<tr>
			<td>10&#176; Nom. VIS 0&#176; Coated, Wedge Prism</td>
			<td>EDMUND OPTICS</td>
			<td>#49-444</td>
			<td></td>
		</tr>
		<tr>
			<td>2.5&#176; Nom. Fused Silica Wedge Prism Uncoated</td>
			<td>EDMUND OPTICS</td>
			<td>#84-863</td>
			<td></td>
		</tr>
		<tr>
			<td>4&#176; Nom. Uncoated, Wedge Prism</td>
			<td>EDMUND OPTICS</td>
			<td>#43-650</td>
			<td></td>
		</tr>
		<tr>
			<td>5.0&#176; Nom. Fused Silica Wedge Prism Uncoated</td>
			<td>EDMUND OPTICS</td>
			<td>#84-865</td>
			<td></td>
		</tr>
		<tr>
			<td>LabView Full Development System</td>
			<td>National Instruments</td>
			<td>776670-35</td>
			<td></td>
		</tr>
	</tbody>
</table>

measurements of waves in a wind-wave tank under steady and time-varying wind forcing

This manuscript describes an experimental procedure that allows obtaining diverse quantitative information on temporal and spatial evolution of water waves excited by time-dependent and steady wind forcing. Capacitance-type wave gauge and Laser Slope Gauge (LSG) are used to measure instantaneous water surface elevation and two components of the instantaneous surface slope at a number of locations along the test section of a wind-wave facility. The computer-controlled blower provides airflow over the water in the tank whose rate can vary in time. In the present experiments, the wind speed in the test section initially increases quickly from rest to the set value. It is then kept constant for the prescribed duration; finally, the airflow is shut down. At the beginning of each experimental run, the water surface is calm and there is no wind. Operation of the blower is initiated simultaneously with the acquisition of data provided by all sensors by a computer; data acquisition continues until the waves in the tank fully decay. Multiple independent runs performed under identical forcing conditions allow determining statistically reliable ensemble-averaged characteristic parameters that quantitatively describe wind-waves&#39; variation in time for the initial development stage as a function of fetch. The procedure also allows characterizing the spatial evolution of the wave field under steady wind forcing, as well as decay of waves in time, once the wind is shut down, as a function of fetch.

The representative ensemble-averaged results are plotted in Figure 6, Figure 7, and Figure 8. The variation of the RMS values of the instantaneous surface elevation &#60;&#951;2&#62;1/2 that characterizes the amplitude of random wind waves as presented in Figure 6 as a function of time elapsed since initiation of the b...

Watch this Scientific Journal Video about Measurements of Waves in a Wind-wave Tank Under Steady and Time-varying Wind Forcing at JoVE.com

Measurements of Waves in a Wind-wave Tank Under Steady and Time-varying Wind Forcing

This manuscript describes a fully computer-controlled procedure that allows obtaining reliable statistical parameters from experiments of water waves excited by steady and unsteady wind forcing in a small-scale facility.

This manuscript describes an experimental procedure that allows obtaining diverse quantitative information on temporal and spatial evolution of water ...

The overall goal of this experimental procedure is to enable accumulation of diverse reliable statistical parameters that characterize spatial and temporal evolution of water waves under study and time-dependent wind forcing. This method can clarify mechanism that govern excitation of water waves by wind. These mechanisms are not yet understood.Proper modeling of wind input is essential for wave climate forecasting. The main advantage of this technique is that it is fully automated and computer-controlled. The experimental procedure can be easily adjusted for study wide variety of process and wind-wave generation.The experiments take place in this facility, which consists of a closed-loop wind tunnel above a wave tank. This is a schematic of the facility and some of its features. The direction of airflow is indicated by arrows.The tank is five meters long, 1/2 meters tall and 4/10 of a meter wide. The tank side walls and floor are made of glass supported by an aluminum frame. There is a flap and wave generator at one end of the tank.The flap smoothly expands the airflow cross-section as it enters the test area and serves as a reference for distance measurements. A wave energy absorber is at the opposite end of the tank. This consists of porous packing materials used to form a beach.There is a moveable carriage above the tank to hold instruments. For the experiment, have the tank filled to a depth of 20 centimeters and manually precision the carriage so the instruments will be at the desired fetch. Next, prepare some of the instruments for the experiment.Have a Pitot tube that can reach the center of the airflow. In addition, have a wave gauge that is mounted on a computer-controlled vertical stage. Use the carriage to mount the Pitot tube at the center of the test section's airflow.Then, mount the wave gauge on the carriage. Next, work with a laser slope gauges part. These consist of a laser diode, a Fresnel lens, a diffusive screen and a precision-sensing detector.Align the laser diode at the desired fetch below the water tank. Direct the beam vertically upward. The beam should be about seven centimeters from the wave gauge.After positioning the Fresnel lens and diffusive screen, use a level to check the horizontal and vertical alignment of the lens and screen before proceeding. Adjust the lens setting to the actual distance between the lens and the screen. To calibrate the wave gauge, set the vertical precision of the sensor.The mean water level should be approximately in the middle of the sensing wire's length. Set the blower speed to one of the desired levels and allow the wind to blow steadily for two to three minutes. As the wind blows, monitor the wave gauge's signal on an oscilloscope.Manually adjust the sensibility, gain and offset to ensure the voltage values corresponding to the highest crest and lowest trough are in the range of the AD converter. When done, shut down the blower and wait until the water surface is undisturbed. Repeat the calibration steps for each measuring location and maximum wind velocity expected in the experimental run.Now, calibrate the laser slope gauge. For this, use an optical wedge prism on a transparent support. View the output of the precision-sensing detector on an oscilloscope to check the calibration.Use different prisms to repeat this for several deflection angles. Once again, use a prism to deflect the vertical laser beam. In this case, deflect the beam to a radial position on the diffusive screen.Do this with several prisms while maintaining a constant azimuthal angle. For each position, record the output of the precision-sensing detector on the oscilloscope. When done, collect data by moving the laser spot to multiple positions in the X direction keeping the Y-coordinate constant.Repeat the same steps moving the Y-position and keeping the X-coordinate constant. Prepare the data acquisition system to record the desired quantities. To begin the experiment, make sure there is no wind.The water surface should be smooth and undisturbed. Activate the blower and start data acquisition at the same time. For this experiment, apply steady forcing for 200 seconds.Over time, the system will achieve a steady state. Use the oscilloscope to display data as it is being collected. This is an example of the surface slope data.Downwind on the left, cross-wind on the right. At the conclusion, shut down the blower and continue to collect data to record the decaying wave field. Allow sufficient time for the water to return to an undisturbed state before continuing.In each realization, three distinct stages can be identified. The initial wave growth with a start of the blower. The quasi-steady wind-wave field under constant wind forcing, and the decay of the waves following shutdown of the blower.Numerous independent realizations of wave field under impulsive wind forcing were recorded. And sample averaging provides results as a function of time relative to the instant of blower initiation. Here are the data for the RMS values of the instantaneous surface elevation as a function of time.The data were taken 120 centimeters from the flap and for three different wind velocities. The equilibrium quasi-steady-state characteristic wave amplitude increases with the wind velocity. Note the time to obtain the quasi-steady-state value does not appear to depend on the velocity.Data for different fetch values and the same three wind velocities show similar behavior. These plots are for instantaneous surface elevations. 220 centimeters from the flap, and 340 centimeters from the flap.Use the same data to explore the characteristic wave amplitudes for a constant target value of the wind velocity. This plot, for 6.5 meters per second is representative and demonstrates the equilibrium values of the RMS values of the surface elevation increases with fetch. The experiment also provides measurements of the RMS downwind and cross-wind components of the surface slope.These data are for two values of the fetch, 120 centimeters and 340 centimeters. For a target wind velocity of 6.5 meters per second, and also for a target wind velocity of 10.5 meters per second. Turn off the blower and the characteristic wave amplitude together with the surface slope components decay over about one minute independent of the fetch.Once mastered, a single realization using this procedure takes about eight minutes. The accumulation of 100 realizations requires about 13 hours of continuous experiment for a single wind target velocity and a fixed fetch. While attempting this procedure, it's important to remember that water evaporates and should be replenished from time to time.After its development, this technique paved the way for quantitative investigation water waves and steady wind forcing. After watching the video, you should have a good understanding of how quantitative results on unsteady and inhomogeneous wind-wave fields can be obtained.

measurements-waves-wind-wave-tank-under-steady-time-varying-wind

Research

Education

JoVE Journal

JoVE Core

Engineering

Physics

Electrical Engineering

Unit 1

First and Second-Order Circuits

Waves

SCIENTISTS IN ACTION

8.5K Views.  Tel-Aviv University. The overall goal of this experimental procedure is to enable accumulation of diverse reliable statistical parameters that characterize spatial and temporal evolution of water waves under study and time-dependent wind forcing. This method can clarify mechanism that govern excitation of water waves by wind. These mechanisms are not yet understood.Proper modeling of wind input is essential for wave climate forecasting. The main advantage of this technique is that it is fully automated and...

Video: Measurements of Waves in a Wind-wave Tank Under Steady and Time-varying Wind Forcing

Measuring Material Microstructure Under Flow Using 1-2 Plane Flow-Small Angle Neutron Scattering

A new small-angle neutron scattering (SANS) sample environment optimized for studying the microstructure of complex fluids under simple shear flow is presented. The SANS shear cell consists of a concentric cylinder Couette geometry that is sealed and rotating about a horizontal axis so that the vorticity direction of the flow field is aligned with the neutron beam enabling scattering from the 1-2 plane of shear (velocity-velocity gradient, respectively). This approach is an advance over previous shear cell sample environments as there is a strong coupling between the bulk rheology and microstructural features in the 1-2 plane of shear. Flow-instabilities, such as shear banding, can also be studied by spatially resolved measurements. This is accomplished in this sample environment by using a narrow aperture for the neutron beam and scanning along the velocity gradient direction. Time resolved experiments, such as flow start-ups and large amplitude oscillatory shear flow are also possible by synchronization of the shear motion and time-resolved detection of scattered neutrons. Representative results using the methods outlined here demonstrate the useful nature of spatial resolution for measuring the microstructure of a wormlike micelle solution that exhibits shear banding, a phenomenon that can only be investigated by resolving the structure along the velocity gradient direction. Finally, potential improvements to the current design are discussed along with suggestions for supplementary experiments as motivation for future experiments on a broad range of complex fluids in a variety of shear motions.

A shear cell is developed for small-angle neutron scattering measurements in the velocity-velocity gradient plane of shear and is used to characterize complex fluids. Spatially resolved measurements in the velocity gradient direction are possible for studying shear-banding materials. Applications include investigations of colloidal dispersions, polymer solutions, and self-assembled structures.

A new small-angle neutron scattering (SANS) sample environment optimized for studying the microstructure of complex fluids under simple shear flow is ...

Preparation and Friction Force Microscopy Measurements of Immiscible, Opposing Polymer Brushes

Solvated polymer brushes are well known to lubricate high-pressure contacts, because they can sustain a positive normal load while maintaining low friction at the interface. Nevertheless, these systems can be sensitive to wear due to interdigitation of the opposing brushes. In a recent publication, we have shown via molecular dynamics simulations and atomic force microscopy experiments, that using an immiscible polymer brush system terminating the substrate and the slider surfaces, respectively, can eliminate such interdigitation. As a consequence, wear in the contacts is reduced. Moreover, the friction force is two orders of magnitude lower compared to traditional miscible polymer brush systems. This newly proposed system therefore holds great potential for application in industry. Here, the methodology to construct an immiscible polymer brush system of two different brushes each solvated by their own preferred solvent is presented. The procedure how to graft poly(N-isopropylacrylamide) (PNIPAM) from a flat surface and poly(methyl methacrylate) (PMMA) from an atomic force microscopy (AFM) colloidal probe is described. PNIPAM is solvated in water and PMMA in acetophenone. Via friction force AFM measurements, it is shown that the friction for this system is indeed reduced by two orders of magnitude compared to the miscible system of PMMA on PMMA solvated in acetophenone.

The methodology to perform friction force microscopy experiments for contacting brushes is presented: Two polymer brushes that are grafted from (a) substrates and (b) colloidal probes are slid to show that, by using two contacting immiscible brush systems, friction in sliding contacts is reduced compared to miscible brush systems.

Solvated polymer brushes are well known to lubricate high-pressure contacts, because they can sustain a positive normal load while maintaining low ...

Preparation and Evaluation of Hybrid Composites of Chemical Fuel and Multi-walled Carbon Nanotubes in the Study of Thermopower Waves

When a chemical fuel at a certain position in a hybrid composite of the fuel and a micro/nanostructured material is ignited, chemical combustion occurs along the interface between the fuel and core materials. Simultaneously, dynamic changes in thermal and chemical potentials across the micro/nanostructured materials result in concomitant electrical energy generation induced by charge transfer in the form of a high-output voltage pulse. We demonstrate the entire procedure of a thermopower wave experiment, from synthesis to evaluation. Thermal chemical vapor deposition and the wet impregnation process are respectively employed for the synthesis of a multi-walled carbon nanotube array and a hybrid composite of picric acid/sodium azide/multi-walled carbon nanotubes. The prepared hybrid composites are used to fabricate a thermopower wave generator with connecting electrodes. The combustion of the hybrid composite is initiated by laser heating or Joule-heating, and the corresponding combustion propagation, direct electrical energy generation, and real-time temperature changes are measured using a high-speed microscopy system, an oscilloscope, and an optical pyrometer, respectively. Furthermore, the crucial strategies to be adopted in the synthesis of hybrid composite and initiation of their combustion that enhance the overall thermopower wave energy transfer are proposed.

A protocol for conducting thermopower wave experiments is presented. The synthesis of hybrid composites of a chemical fuel and micro/nanostructured material, manufacturing of a thermopower wave generator, and methods for measuring the corresponding physical phenomena are described.

When a chemical fuel at a certain position in a hybrid composite of the fuel and a micro/nanostructured material is ignited, chemical combustion occurs ...

Speciation and Bioavailability Measurements of Environmental Plutonium Using Diffusion in Thin Films

The biological uptake of plutonium (Pu) in aquatic ecosystems is of particular concern since it is an alpha-particle emitter with long half-life which can potentially contribute to the exposure of biota and humans. The diffusive gradients in thin films technique is introduced here for in-situ measurements of Pu bioavailability and speciation. A diffusion cell constructed for laboratory experiments with Pu and the newly developed protocol make it possible to simulate the environmental behavior of Pu in model solutions of various chemical compositions. Adjustment of the oxidation states to Pu(IV) and Pu(V) described in this protocol is essential in order to investigate the complex redox chemistry of plutonium in the environment. The calibration of this technique and the results obtained in the laboratory experiments enable to develop a specific DGT device for in-situ Pu measurements in freshwaters. Accelerator-based mass-spectrometry measurements of Pu accumulated by DGTs in a karst spring allowed determining the bioavailability of Pu in a mineral freshwater environment. Application of this protocol for Pu measurements using DGT devices has a large potential to improve our understanding of the speciation and the biological transfer of Pu in aquatic ecosystems.

The technique of diffusive gradients in thin films (DGT) is proposed for speciation studies of plutonium. This protocol describes diffusion experiments probing the behavior of Pu(IV) and Pu(V) in presence of organic matter. DGTs deployed in a karstic spring allow assessment of the bioavailability of Pu.

The biological uptake of plutonium (Pu) in aquatic ecosystems is of particular concern since it is an alpha-particle emitter with long half-life which can ...

Experimental Protocol to Investigate Particle Aerosolization of a Product Under Abrasion and Under Environmental Weathering

The present article presents an experimental protocol to investigate particle aerosolization of a product under abrasion and under environmental weathering, which is a fundamental element to the approach of nanosafety-by-design of nanostructured products for their durable development. This approach is basically a preemptive one in which the focus is put on minimizing the emission of engineered nanomaterials' aerosols during the usage phase of the product's life cycle. This can be attained by altering its material properties during its design phase without compromising with any of its added benefits. In this article, an experimental protocol is presented to investigate the nanosafety-by-design of three commercial nanostructured products with respect to their mechanical solicitation and environmental weathering. The means chosen for applying the mechanical solicitation is an abrasion process and for the environmental weathering, it is an accelerated UV exposure in the presence of humidity and heat. The eventual emission of engineered nanomaterials is studied in terms of their number concentration, size distribution, morphology and chemical composition. The purpose of the protocol is to study the emission for test samples and experimental conditions which are corresponding to real life situations. It was found that the application of the mechanical stresses alone emits the engineered nanomaterials' aerosols in which the engineered nanomaterial is always embedded inside the product matrix, thus, a representative product element. In such a case, the emitted aerosols comprise of both nanoparticles as well as microparticles. But if the mechanical stresses are coupled with the environmental weathering, the experimental protocol reveals then the eventual deterioration of the product, after a certain weathering duration, may lead to the emission of the free engineered nanomaterial aerosols too.

In this article, an experimental protocol to investigate particle aerosolization of a product under abrasion and under environmental weathering is presented. Results on the emission of engineered nanomaterials, in the form of aerosols are presented. The specific experimental set-up is described in detail.

The present article presents an experimental protocol to investigate particle aerosolization of a product under abrasion and under environmental ...

Automation of Mode Locking in a Nonlinear Polarization Rotation Fiber Laser through Output Polarization Measurements

When a laser is mode-locked, it emits a train of ultra-short pulses at a repetition rate determined by the laser cavity length. This article outlines a new and inexpensive procedure to force mode locking in a pre-adjusted nonlinear polarization rotation fiber laser. This procedure is based on the detection of a sudden change in the output polarization state when mode locking occurs. This change is used to command the alignment of the intra-cavity polarization controller in order to find mode-locking conditions. More specifically, the value of the first Stokes parameter varies when the angle of the polarization controller is swept and, moreover, it undergoes an abrupt variation when the laser enters the mode-locked state. Monitoring this abrupt variation provides a practical easy-to-detect signal that can be used to command the alignment of the polarization controller and drive the laser towards mode locking. This monitoring is achieved by feeding a small portion of the signal to a polarization analyzer measuring the first Stokes parameter. A sudden change in the read out of this parameter from the analyzer will occur when the laser enters the mode-locked state. At this moment, the required angle of the polarization controller is kept fixed. The alignment is completed. This procedure provides an alternate way to existing automating procedures that use equipment such as an optical spectrum analyzer, an RF spectrum analyzer, a photodiode connected to an electronic pulse-counter or a nonlinear detecting scheme based on two-photon absorption or second harmonic generation. It is suitable for lasers mode locked by nonlinear polarization rotation. It is relatively easy to implement, it requires inexpensive means, especially at a wavelength of 1550 nm, and it lowers the production and operation costs incurred in comparison to the above-mentioned techniques.

A protocol to detect and automate mode locking in a pre-adjusted nonlinear polarization rotation fiber laser is presented. The detection of a sudden change in the output polarization state when mode locking occurs is used to command the alignment of an intra-cavity polarization controller in order to find mode-locking conditions.

When a laser is mode-locked, it emits a train of ultra-short pulses at a repetition rate determined by the laser cavity length. This article outlines a ...

Fabrication and Operation of Acoustofluidic Devices Supporting Bulk Acoustic Standing Waves for Sheathless Focusing of Particles

Acoustophoresis refers to the displacement of suspended objects in response to directional forces from sound energy. Given that the suspended objects must be smaller than the incident wavelength of sound and the width of the fluidic channels are typically tens to hundreds of micrometers across, acoustofluidic devices typically use ultrasonic waves generated from a piezoelectric transducer pulsating at high frequencies (in the megahertz range). At characteristic frequencies that depend on the geometry of the device, it is possible to induce the formation of standing waves that can focus particles along desired fluidic streamlines within a bulk flow. Here, we describe a method for the fabrication of acoustophoretic devices from common materials and clean room equipment. We show representative results for the focusing of particles with positive or negative acoustic contrast factors, which move towards the pressure nodes or antinodes of the standing waves, respectively. These devices offer enormous practical utility for precisely positioning large numbers of microscopic entities (e.g., cells) in stationary or flowing fluids for applications ranging from cytometry to assembly.

Acoustofluidic devices use ultrasonic waves within microfluidic channels to manipulate, concentrate and isolate suspended micro and nanoscopic entities. This protocol describes the fabrication and operation of such a device supporting bulk acoustic standing waves to focus particles in a central streamline without the aid of sheath fluids.

Acoustophoresis refers to the displacement of suspended objects in response to directional forces from sound energy. Given that the suspended objects must ...

Experimental Methodology for Estimation of Local Heat Fluxes and Burning Rates in Steady Laminar Boundary Layer Diffusion Flames

Modeling the realistic burning behavior of condensed-phase fuels has remained out of reach, in part because of an inability to resolve the complex interactions occurring at the interface between gas-phase flames and condensed-phase fuels. The current research provides a technique to explore the dynamic relationship between a combustible condensed fuel surface and gas-phase flames in laminar boundary layers. Experiments have previously been conducted in both forced and free convective environments over both solid and liquid fuels. A unique methodology, based on the Reynolds Analogy, was used to estimate local mass burning rates and flame heat fluxes for these laminar boundary layer diffusion flames utilizing local temperature gradients at the fuel surface. Local mass burning rates and convective and radiative heat feedback from the flames were measured in both the pyrolysis and plume regions by using temperature gradients mapped near the wall by a two-axis traverse system. These experiments are time-consuming and can be challenging to design as the condensed fuel surface burns steadily for only a limited period of time following ignition. The temperature profiles near the fuel surface need to be mapped during steady burning of a condensed fuel surface at a very high spatial resolution in order to capture reasonable estimates of local temperature gradients. Careful corrections for radiative heat losses from the thermocouples are also essential for accurate measurements. For these reasons, the whole experimental setup needs to be automated with a computer-controlled traverse mechanism, eliminating most errors due to positioning of a micro-thermocouple. An outline of steps to reproducibly capture near-wall temperature gradients and use them to assess local burning rates and heat fluxes is provided.

We describe the use of micro-thermocouples to estimate local temperature gradients in steady laminar boundary layer diffusion flames. By extension of the Reynolds Analogy, local temperature gradients can be further used to estimate the local mass burning rates and heat fluxes in such flames with high accuracy.

Modeling the realistic burning behavior of condensed-phase fuels has remained out of reach, in part because of an inability to resolve the complex ...

In Situ Visualization of the Phase Behavior of Oil Samples Under Refinery Process Conditions

To help address production issues in refineries caused by the fouling of process units and lines, we have developed a setup as well as a method to visualize the behavior of petroleum samples under process conditions. The experimental setup relies on a custom-built micro-reactor fitted with a sapphire window at the bottom, which is placed over the objective of an inverted microscope equipped with a cross-polarizer module. Using reflection microscopy enables the visualization of opaque samples, such as petroleum vacuum residues, or asphaltenes. The combination of the sapphire window from the micro-reactor with the cross-polarizer module of the microscope on the light path allows high-contrast imaging of isotropic and anisotropic media. While observations are carried out, the micro-reactor can be heated to the temperature range of cracking reactions (up to 450 &#176;C), can be subjected to H2 pressure relevant to hydroconversion reactions (up to 16 MPa), and can stir the sample by magnetic coupling. 
Observations are typically carried out by taking snapshots of the sample under cross-polarized light at regular time intervals. Image analyses may not only provide information on the temperature, pressure, and reactive conditions yielding phase separation, but may also give an estimate of the evolution of the chemical (absorption/reflection spectra) and physical (refractive index) properties of the sample before the onset of phase separation.

In Situ Visualization of the Phase Behavior of Oil Samples Under Refinery Process Conditions

This article describes a setup and method for the in situ visualization of oil samples under a variety of temperature and pressure conditions that aim to emulate refining and upgrading processes. It is primarily used for studying isotropic and anisotropic media involved in the fouling behavior of petroleum feeds.

To help address production issues in refineries caused by the fouling of process units and lines, we have developed a setup as well as a method to ...

Measurements of Soil Carbon by Neutron-Gamma Analysis in Static and Scanning Modes

The herein described application of the inelastic neutron scattering (INS) method for soil carbon analysis is based on the registration and analysis of gamma rays created when neutrons interact with soil elements. The main parts of the INS system are a pulsed neutron generator, NaI(Tl) gamma detectors, split electronics to separate gamma spectra due to INS and thermo-neutron capture (TNC) processes, and software for gamma spectra acquisition and data processing. This method has several advantages over other methods in that it is a non-destructive in situ method that measures the average carbon content in large soil volumes, is negligibly impacted by local sharp changes in soil carbon, and can be used in stationary or scanning modes. The result of the INS method is the carbon content from a site with a footprint of ~2.5 - 3 m2 in the stationary regime, or the average carbon content of the traversed area in the scanning regime. The measurement range of the current INS system is &#62;1.5 carbon weight % (standard deviation &#177; 0.3 w%) in the upper 10 cm soil layer for a 1 hmeasurement.

Here, we present the protocol for in situ measurement of soil carbon using the neutron-gamma technique for single point measurements (static mode) or field averages (scanning mode). We also describe system construction and elaborate data treatment procedures.

The herein described application of the inelastic neutron scattering (INS) method for soil carbon analysis is based on the registration and analysis of ...