Name: high-resolution patterning using two modes of electrohydrodynamic jet: drop on demand and near-field electrospinning
Uploaded: 2018-07-10T14:00:00
Description: Watch this Scientific Journal Video about High-resolution Patterning Using Two Modes of Electrohydrodynamic Jet: Drop on Demand and Near-field Electrospinning at JoVE.com

This research was supported by the Basic Science Research Program through the National Research Foundation of Korea (NRF) of Korea, funded by the Ministry of Education (2016R1D1A1B01006801), and partially supported by the Soonchunhyang University Research Fund.

For health and safety purposes, prior to using any ink and cleaning solution, refer to the material safety datasheet (MSDS).
1. Drop-on-demand Electrohydrodynamic Jet Printing Using Silver Nanoparticle Ink
<ol>
	<li>Fill the filtered silver nanoparticle (AgNP) ink in the ink reservoir of the EHD printing system. 
	Note: Commercially available AgNP ink can be used for the inkjet purpose. The ink should have a viscosity of around 10 cP and a surface tension of 20 ~ 40 mN/m to obtain drop-...

<ol>
	<li>Onses, M. S., Sutanto, E., Ferreira, P. M., Alleyne, A. G., Rogers, J. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Mechanisms,+Capabilities,+and+Applications+of+High-Resolution+Electrohydrodynamic+Jet+Printing.">Mechanisms, Capabilities, and Applications of High-Resolution Electrohydrodynamic Jet Printing.</a> Small. 11 (34), 4237-4266 (2015).</li><li>Jaworek, A., Krupa, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Classification+of+the+modes+of+EHD+spraying.">Classification of the modes of EHD spraying.</a> Journal of Aerosol Science. 30 (93), 873-893 (1999).</li><li>Lee, A., Jin, H., Dang, H. W., Choi, K. H., Ahn, K. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Optimization+of+experimental+parameters+to+determine+the+jetting+regimes+in+electrohydrodynamic+printing.">Optimization of experimental parameters to determine the jetting regimes in electrohydrodynamic printing.</a> Langmuir. 29 (44), 13630-13639 (2013).</li><li>Sun, D., Chang, C., Li, S., Lin, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Near-field+electrospinning.">Near-field electrospinning.</a> Nano Letters. 6 (4), 839-842 (2006).</li><li>Pan, C. -. T., Tsai, K. -. C., Wang, S. -. Y., Yen, C. -. K., Lin, Y. -. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Large-Area+Piezoelectric+PVDF+Fibers+Fabricated+by+Near-Field+Electrospinning+with+Multi-Spinneret+Structures.">Large-Area Piezoelectric PVDF Fibers Fabricated by Near-Field Electrospinning with Multi-Spinneret Structures.</a> Micromachines. 8 (4), (2017).</li><li>Mishra, S., Barton, K. L., Alleyne, A. G., Ferreira, P. M., Rogers, J. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=High-speed+and+drop-on-demand+printing+with+a+pulsed+electrohydrodynamic+jet.">High-speed and drop-on-demand printing with a pulsed electrohydrodynamic jet.</a> Journal of Micromechanics and Microengineering. 20 (9), (2010).</li><li>Kwon, K. S., Lee, D. Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Investigation+of+pulse+voltage+shape+effects+on+electrohydrodynamic+jets+using+a+vision+measurement+technique.">Investigation of pulse voltage shape effects on electrohydrodynamic jets using a vision measurement technique.</a> Journal of Micromechanics and Microengineering. 23 (6), (2013).</li><li>Chen, C. H., Saville, D. A., Aksay, I. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Scaling+laws+for+pulsed+electrohydrodynamic+drop+formation.">Scaling laws for pulsed electrohydrodynamic drop formation.</a> Applied Physics Letters. 89, (2006).</li><li>Sung, K., Lee, C. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Factors+influencing+liquid+breakup+in+electrohydrodynamic+atomization.">Factors influencing liquid breakup in electrohydrodynamic atomization.</a> Journal of Applied Physics. 96 (7), 3956-3961 (2004).</li><li>Kim, J. H., Oh, H. C., Kim, S. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Electrohydrodynamic+drop-on-demand+patterning+in+pulsed+cone-jet+mode+at+various+frequencies.">Electrohydrodynamic drop-on-demand patterning in pulsed cone-jet mode at various frequencies.</a> Journal of Aerosol Science. 39 (9), 819-825 (2007).</li><li>Phung, T. H., Kim, S., Kwon, K. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+high+speed+electrohydrodynamic+(EHD)+jet+printing+method+for+line+printing.">A high speed electrohydrodynamic (EHD) jet printing method for line printing.</a> Journal of Micromechanics and Microengineering. 27, (2017).</li><li>Teo, W. E., Ramakrishna, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+review+on+electrospinning+design+and+nano+fiber+assemblies.">A review on electrospinning design and nano fiber assemblies.</a> Nanotechnology. 17, R89-R106 (2006).</li><li>Tang, Y., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Highly+relective+nanofiber+films+based+on+electrospinning+and+their+application+on+color+uniformity+and+luminous+efficacy.">Highly relective nanofiber films based on electrospinning and their application on color uniformity and luminous efficacy.</a> Optics Express. 25, 20598-20611 (2017).</li><li>Huebner, G., Zapka, W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Comparing+inkjet+with+other+printing+processes+and+mainly+screen+printing.">Comparing inkjet with other printing processes and mainly screen printing.</a> Handbook of Industrial Inkjet Printing - A Full System Approach. 1, 7-22 (2018).</li><li>Li, M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Electrospun+protein+fibers+as+matrices+for+tissue+engineering.">Electrospun protein fibers as matrices for tissue engineering.</a> Biomaterials. 26, 5999-6008 (2005).</li><li>Bhardwaj, N., Kundu, C. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Electrospinning:+A+fascinating+fiber+fabrication+technique.">Electrospinning: A fascinating fiber fabrication technique.</a> Biotechnology Advances. 28, 325-347 (2010).</li><li>He, X., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Near-Field+Electrospinning:+Progress+and+Applications.">Near-Field Electrospinning: Progress and Applications.</a> The Journal of Physical Chemistry C. 121, 8663-8678 (2017).</li><li>Yang, T. L., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Synthesis+and+fabrication+of+silver+nanowires+embedded+in+PVP+fibers+by+near-field+electrospinning+process.">Synthesis and fabrication of silver nanowires embedded in PVP fibers by near-field electrospinning process.</a> Optical Materials. 39, 118-124 (2015).</li><li>Chang, C., Limkrailassiri, K., Lin, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Continuous+near-field+electrospinning+for+large+area+deposition+of+orderly+nanofiber+patterns.">Continuous near-field electrospinning for large area deposition of orderly nanofiber patterns.</a> Applied Physics Letters. 93 (12), (2008).</li></ol>

In this protocol, we focus on printing fine patterns using AgNP ink with two modes: DOD EHD printing and NFES. However, the EHD jet printing application is not limited to the conductive ink using AgNP. Here, we will discuss the general guidelines for the selection of ink, the system configuration, and other printing parameters needed to use EHD jet printing for various fine-pattern applications.
The first and most important step for EHD printing is ink selection and preparation. The ink used i...

EHD jet printing has been widely used in various areas, such as printed electronics, biotechnology, and advanced material applications, because it is capable of high-resolution and low-cost direct patterning1. The printed line width or printed dot size could be reduced to 1 &#181;m, which is significantly smaller than that of conventional piezo-based inkjet printing1.
In EHD printing, a small portion of ink (or meniscus) is pushed out of the nozzle tip and maintained by controlling the flow rate1,2,3,4,5 or the positive air pressure1,6,7. The extruded meniscus is charged and can easily be pulled down from the nozzle tip to the substrate by an electric field, as shown in Figure 1. The conical meniscus is formed during the jetting, producing an ink stream much thinner than the nozzle size.
<img alt="Figure 1" class="xfigimg" src="/files/ftp_upload/57846/57846fig1.jpg" /> 
Figure 1: EHD printing. The figure shows the principle of EHD jet printing. Ink is pushed via pressure and pulled via an electric field to form an extruded meniscus from the nozzle. Then, the charged ink can be easily jetted to the substrate via a DC or pulse voltage. <a href="https://www.jove.com/files/ftp_upload/57846/57846fig1large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
Even though a single EHD printer can be used for the two different modes, near-field electrospinning (NFES) and drop-on-demand (DOD) EHD jet printing, the realization methods significantly differ in terms of ink, fluidic system, and driving voltage1,2,3. For example, NFES4,5 uses a relatively high-viscous ink [more than 1,000 centipoises (cP)] to form continuous micro-line patterns with high-speed printing up to 1 m/s. On the other hand, DOD EHD jet printing6,7,8 uses low-viscous ink with a viscosity of around 10 cP to print dot-based complex patterns with a low printing speed less than 10 mm/s.
Since the requirement for each mode is significantly different, it may be challenging for inexperienced researchers to achieve the desired results. The empirical &#34;know-how&#34; might be important in practice. To help researchers get used to the printing methods, we present EHD printing protocols for fine conductive patterning using Ag nanoparticle ink. However, we added comments to the protocols so that they are not limited to a conductive patterning using Ag nanoparticle ink. Finally, printing and preparation guidelines are presented in the discussion section.

<table border="0" cellpadding="0" cellspacing="0" width="696">
	<tbody>
		<tr height="23">
			<td height="23" style="height:23px;width:216px;">EHD integrated printing system</td>
			<td style="width:195px;">Psolution Ltd., South Korea</td>
			<td style="width:119px;">PS300</td>
			<td style="width:167px;"></td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:216px;">Harima Ag Nanoparticle ink</td>
			<td style="width:195px;">Harima Inc., Japan</td>
			<td style="width:119px;">Harima NPS-JL</td>
			<td>Ag solid content: ~ 53 wt%, Viscosity: ~10 cP, Surface tension: ~30 mN/m</td>
		</tr>
		<tr height="42">
			<td height="42" style="height:42px;width:216px;">Glass capillary</td>
			<td style="width:195px;">Narishige Scientific Instrument Lab</td>
			<td style="width:119px;">G-1</td>
			<td>Inner diameter: 1 mm; Used to make nozzle for DOD EHD jet printing using thermal puller</td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:216px;">Nozzle thermal puller</td>
			<td style="width:195px;">Sutter Instrument, USA</td>
			<td style="width:119px;">Sutter P-1000</td>
			<td></td>
		</tr>
		<tr height="42">
			<td height="42" style="height:42px;width:216px;">Microscope Slides (Glass subtrate)</td>
			<td style="width:195px;">Paul-Marienfeld &#38; Co.KG, Germany</td>
			<td style="width:119px;">10 006 12</td>
			<td>Dimension (L x W x T): 76 mm x 26 mm x 1 mm</td>
		</tr>
		<tr height="42">
			<td height="42" style="height:42px;width:216px;">Magnetic Stirrer</td>
			<td style="width:195px;">Barnstead Thermolyne Corp., USA</td>
			<td style="width:119px;">Cimarec SP131635</td>
			<td></td>
		</tr>
		<tr height="42">
			<td height="42" style="height:42px;width:216px;">Vortex Stirrer</td>
			<td style="width:195px;">Jeiotech, South Korea</td>
			<td style="width:119px;">Lab Companion VM-96T</td>
			<td></td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:216px;">Ag nanopaste&#160;</td>
			<td style="width:195px;">NPK, South Korea</td>
			<td style="width:119px;">ES-R001</td>
			<td>Ag solid content: ~85.5 wt%, Viscosity: ~11000 cP</td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:216px;">Poly ethylene oxide (PEO)</td>
			<td style="width:195px;">Sigma-Aldrich, USA</td>
			<td>372773-500G</td>
			<td>Mw = 400000</td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:216px;">Ethanol</td>
			<td style="width:195px;">Sigma-Aldrich, USA</td>
			<td>459836-500ML</td>
			<td></td>
		</tr>
	</tbody>
</table>

high-resolution patterning using two modes of electrohydrodynamic jet: drop on demand and near-field electrospinning

Electrohydrodynamic (EHD) jet printing has drawn attention in various fields because it can be used as a high-resolution and low-cost direct patterning tool. EHD printing uses a fluidic supplier to maintain the extruded meniscus by pushing the ink out of the nozzle tip. The electric field is then used to pull the meniscus down to the substrate to produce high-resolution patterns. Two modes of EHD printing have been used for fine patterning: continuous near-field electrospinning (NFES) and dot-based drop-on-demand (DOD) EHD printing. According to the printing modes, the requirements for the printing equipment and ink viscosity will differ. Even though two different modes can be implemented with a single EHD printer, the realization methods significantly differ in terms of ink, fluidic system, and driving voltage. Consequently, without a proper understanding of the jetting requirements and limitations, it is difficult to obtain the desired results. The purpose of this paper is to present a guideline so that inexperienced researchers can reduce the trial and error efforts to use the EHD jet for their specific research and development purposes. To demonstrate the fine-patterning implementation, we use Ag nanoparticle ink for the conductive patterning in the protocol. In addition, we also present the generalized printing guidelines that can be used for other types of ink for various fine-patterning applications.

Dot-based drop-on-demand printing: 
DOD printing is based on one droplet jetting per one jetting trigger. To produce DOD jetting, low-viscous ink with a viscosity of approximately 10 cP should be used. The ink requirement for EHD DOD printing is similar to that of the conventional DOD inkjet, as is the EHD printing method to that of the conventional DOD inkjet. In the case of conventional inkjet printing, the raster printing technique has been widely used, because it...

Watch this Scientific Journal Video about High-resolution Patterning Using Two Modes of Electrohydrodynamic Jet: Drop on Demand and Near-field Electrospinning at JoVE.com

High-resolution Patterning Using Two Modes of Electrohydrodynamic Jet: Drop on Demand and Near-field Electrospinning

Here, we present a protocol to produce high-resolution conductive patterns using electrohydrodynamic (EHD) jet printing. The protocol includes two modes of EHD jet printing: the continuous near-field electrospinning (NFES) and the dot-based drop-on-demand (DOD) EHD printing.

Electrohydrodynamic (EHD) jet printing has drawn attention in various fields because it can be used as a high-resolution and low-cost direct patterning ...

Electrohydrodynamic jet printing is a non-contacting, direct patterning method that can be used in various fields, such as printed electronics, advanced materials, biotechnology, and so on. The electrohydrodynamic jet printing method uses a high electric field to pull down charged ink to the substrate. For this purpose, a fluidic system is used to push ink to the nozzle, and a high voltage power supply is used to produce the electrical field.The main advantage of this technique is that it can be used to print very small dots or patterns, compared to conventional inkjet printing method. Based on the electrical and fluidic configurations, three different modes of drop-on-demand printing, electrospinning, and electrospray, can be implemented. For fine patterning, we will focus on DOD and near-field electropsinning.DOD uses both DC voltage and pulse voltage for jetting, whereas near-field electrospinning uses only DC voltage for jetting. Individuals knew that this method would have a hard time attaining proper jetting because it more requires specific things and different printing pen methods, such as voltage, the nozzle, printing speed, and stand-up distance. Courageous student Mr.Oh will demonstrate both drop-on-demand and near-field electrospinning using silver nanoparticle ink, in order to help individuals to understand the printing processors.For drop-on-demand printing, first fill the ink reservoir of the electrohydrodynamic jet printer with filtered silver nanoparticle ink. Then, prepare the nozzle from a glass pipette, as described in the accompanying text protocol. Assemble the nozzle holder by connecting the nozzle to the ink reservoir via Teflon tubing.Next, turn on the air pressure controller, and apply an air pressure of 15 to 20 kilopascal to the ink reservoir. Monitor the ink's flow through the glass nozzle and tubing to ensure that no air is trapped when supplying the ink. Keep applying air pressure to the reservoir until ink appears at the nozzle's tip.Do not reduce the pressure before the ink appears at the nozzle tip because that could cause air bubble entrapment at the tip. Once ink appears at the nozzle's tip, reduce the pressure to around 12 kilopascal. This will maintain the extruded meniscus without any ink dripping from the nozzle's tip.Then, fix the assembled nozzle head in the printing system. Using a side-view camera to visualize the gap between the nozzle tip and the substrate, move the Z-axis of the stage to adjust the gap to approximately 100 micrometers. A smaller gap leads to a higher electric field, which could facilitate printing with a lower and pulse voltages for jetting.However, a lower gap could also lead to larger drops if the voltage is not adjusted properly. At this point, monitor the ink at the nozzle while beginning to apply DC and pulse voltages. Gradually increase the DC voltage at increments less than 100 volts at a time.Once the ink begins to drip from the nozzle, reduce the DC voltage slightly until the ink stops dripping from the nozzle. Next, set a negative pulse voltage with the rise time equal to zero to 100 microseconds, the dwell time equal to 300 microseconds, and the fall time equal to zero microseconds. Then, apply the negative pulse voltage at the substrate holder.Now, adjust the magnitude of the pulse voltage to produce one droplet per single pulse. Then, adjust the DC background and the pulse voltages to obtain the target droplet size on the substrate, while observing the jetted dots on the substrate in the side-view camera image. First, load a bitmap image in the printing tab of the printing software, and convert it into a binary image.Then, set the parameters for the binary image printing. For example, set the distance between two drops, or drop interval, to be ten micrometers. Once set up, start printing using the selected bitmap on the target location of the substrate.To prepare for vector printing, load the pattern's CAD information into the printing software. Then, set the parameters for the print, such as the printing speed and the dot spacing. With the parameters now set, begin printing.To perform near-field electrospinning, first prepare the specially formulated silver nanopaste ink. To accomplish this, mix three parts ethanol and one part deionized water to make 12 milliliters of solvent. Then, mix 0.3 grams of polyethylene oxide and 9.7 grams of the prepared solvent to make a 3%by-weight polymer solution.Using a magnetic stirrer, thoroughly mix the solution for more than six hours by stirring at room temperature. With the solvent now prepared, mix five parts of silver nanopaste ink with one part of the prepared polymer solution. Combine the two using a vortex mixer, mixing for ten minutes to properly suspend the ink.Next, fill the prepared ink into a syringe, and connect the syringe to a nozzle via the Teflon connecting tube. Supply the ink to the nozzle by pushing the syringe manually. When the ink reaches the nozzle, install the syringe into the syringe pump attached to the printing system.Operate the syringe pump to generate an ink flow with an initial flow rate of 50 microliters per minute. When the ink flows out of the nozzle's tip, lower the flow rate to one microliter per minute. Next, apply the DC voltage source to the nozzle connector while the ground voltage is connected to the substrate holder.Increase the DC voltage gradually to 1.5 kilovolts. The DC voltage could be increased up to two kilovolts. However, a DC voltage higher than two kilovolts should be avoided since it might damage the ink.Once set up, start the idle printing with a printing speed of 300 millimeters per second for at least 10 minutes to obtain steady-state flow. This is needed because the viscous ink may be compressed in the lengthy tubing. Adjust the printing parameters, such as the DC voltage and flow rate during idle printing, to obtain the desired printing results.Finally, print your selected pattern on the substrate using the now-defined printing parameters. Dot-based drop-on-demand printing and raster printing uses a single axis to print dots in the main direction and then move to the next swath in the sub-direction. This raster image has a drop size of around four microns.In contrast, dot-based drop-on-demand printing in vector mode performs simultaneous movements in the X and Y directions and is used to print the lines. The resulting image has line widths of four microns. Near-field electrospinning uses highly viscous ink to print patterns continuously.As a result, this method is suitable for printing straight lines using a high printing speed, and is sensitive to changes in print speed. Discardable slow regions should be included in the design to ensure a consistent line size in the desired region. In some cases, a low jetting speed can be used to generate a wave pattern by using a low printing speed of less than 100 millimeters per second.The patterns can become wavy, as shown here. This type of wavy pattern might be useful in stretchable electronics applications. After its development, this technique paved the way for researchers to produce fine patterns for their specific applications.Please note that this printing method is not limited to only silver nanoparticle ink, but can also be used in other applications with various ink. While you're attempting this procedure, it is important to remember to use the appropriate ink for printing. Refer to the general guidelines for ink selection provided in the text of this article.Be sure to adjust the printing parameters according to your ink selection and applications. Don't forget that working with chemicals, high voltage, and high pressure can be hazardous, and precautions should always be taken while performing this procedure.

Research

JoVE Journal

Bioengineering

Visualization of Cortex Organization and Dynamics in Microorganisms, using Total Internal Reflection Fluorescence Microscopy

TIRF microscopy has emerged as  a powerful imaging technology to study spatio-temporal dynamics of fluorescent molecules  in vitro and in living cells1. ...

Continuous High-resolution Microscopic Observation of Replicative Aging in Budding Yeast

We demonstrate the use of a simple microfluidic setup, in which single budding yeast cells can be tracked throughout their entire lifespan. The ...

Microfluidic-based Electrotaxis for On-demand Quantitative Analysis of Caenorhabditis elegans' Locomotion

Microfluidic-based Electrotaxis for On-demand Quantitative Analysis of Caenorhabditis elegans' Locomotion

The nematode Caenorhabditis elegans is a versatile model organism for biomedical research because of its conservation of disease-related genes and ...

Cell Co-culture Patterning Using Aqueous Two-phase Systems

Cell patterning  technologies that are fast, easy to use and affordable will be required for the  future development of high throughput cell assays, ...

Permeabilization of Adhered Cells Using an Inert Gas Jet

Various cell transfection techniques exist and these can be broken down to three broad categories: viral, chemical and mechanical. This protocol describes ...

Cell Patterning on Photolithographically Defined 
Parylene-C: SiO2 Substrates

Cell Patterning on Photolithographically Defined 
Parylene-C: SiO2 Substrates

Cell patterning platforms support broad research goals, such as construction of predefined in vitro neuronal networks and the exploration of certain ...

Using Adhesive Patterning to Construct 3D Paper Microfluidic Devices

We demonstrate the use of patterned aerosol adhesives to construct both planar and nonplanar 3D paper microfluidic devices. By spraying an aerosol ...

Fabricating Degradable Thermoresponsive Hydrogels on Multiple Length Scales via Reactive Extrusion, Microfluidics, Self-assembly, and Electrospinning

While various smart materials have been explored for a variety of biomedical applications (e.g., drug delivery, tissue engineering, bioimaging, etc.), ...

Patterning Bioactive Proteins or Peptides on Hydrogel Using Photochemistry for Biological Applications

There are many biological stimuli that can influence cell behavior and stem cell differentiation. General cell culture approaches rely on soluble factors ...

Quantifying Microorganisms at Low Concentrations Using Digital Holographic Microscopy (DHM)

Quantifying Microorganisms at Low Concentrations Using Digital Holographic Microscopy DHM

Accurately detecting and counting sparse bacterial samples has many applications in the food, beverage, and pharmaceutical processing industries, in ...