Name: determining the mechanical strength of ultra-fine-grained metals
Uploaded: 2021-11-22T13:00:00
Description: Watch this Scientific Journal Video about Determining the Mechanical Strength of Ultra-Fine-Grained Metals at JoVE.com

We acknowledge support from the National Natural Science Foundation of China (NSFC) under grant numbers 11621062, 11772294, U1530402, and 11811530001. This research was also partially supported by the China Postdoctoral Science Foundation (2021M690044). This research used the resources of the Advanced Light Source, which is a DOE Office of Science User Facility under contract number DE-AC02-05CH11231 and the Shanghai Synchrotron Radiation Facility. This research was partially supported by COMPRES, the Consortium for Materials Properties Research in Earth Sciences under NSF Cooperative Agreement EAR 1606856.

1. Sample preparation
<ol>
	<li>Obtain 3 nm, 20 nm, 40 nm, 70 nm, 100 nm, 200 nm, and 500 nm nickel powder from commercial sources (see Table of Materials). The morphology characterization is shown in Figure 1.</li>
	<li>Prepare 8 nm nickel particles by heating 3 nm nickel particles using a reaction kettle (see Table of Materials).
	<ol>
		<li>Put ~20 mL of absolute ethanol and ~50 mg of 3 nm nickel powder into the reaction kettle. NOTE: T...

Computational simulations have been widely employed to study the grain size effect on the strength of nanometals5,6,16,17,27,42. Perfect dislocations, partial dislocations, and GB deformation have been proposed to play decisive roles in the deformation mechanisms of the nanomaterials. In a molecular dynamics simulation, Yamak...

The resistance to plastic deformation determines the materials&#39; strength. The strength of the metals usually increases with the decreasing grain sizes. This size strengthening phenomenon can be well illustrated by the traditional Hall-Petch relationship theory from the millimeter down to submicron regime1,2, which is based on the dislocation-mediated deformation mechanism of bulk-sized metals, i.e., dislocations pile up at grain boundaries (GBs) and hinder their motions, leading to the mechanical strengthening in metals3,4.
In contrast, mechanical softening, often referred to as the inverse Hall-Petch relationship, has been reported for fine nanometals in the last two decades5,6,7,8,9,10. Therefore, the strength of the nanometals is still puzzling as continuous hardening was detected for grain sizes down to ~10 nm11,12, while the cases of size softening below 10 nm regime were also reported7,8,9,10. The main difficulty or challenge for this debated topic is to make statistically reproducible measurements on the mechanical properties of ultrafine nanometals and establish a reliable correlation between the strength and grain size of the nanometals. Another part of the difficulty comes from the ambiguity in the plastic deformation mechanisms of the nanometals. Various defects or processes at nanoscale have been reported, including dislocations13,14, deformation twinning15,16,17, stacking faults15,18, GB migration19, GB sliding5,6,20,21, grain rotation22,23,24, atomic bond parameters25,26,27,28, etc. However, which one dominates the plastic deformation and thus determines the strength of nanometals is still unclear.
For these above issues, traditional approaches of mechanical strength examining, such as tensile test29, Vickers hardness test30,31, nano-indentation test32, micropillar compression33,34,35, etc. are less effective because the high quality of large pieces of nanostructured materials is so difficult to fabricate and conventional indenter is much larger than single nanoparticle of materials (for the single-particle mechanics). In this study, we introduce radial DAC XRD techniques36,37,38 to material science to in situ track the yield stress and deformation texturing of nano nickel of various grain sizes, which are used in the geoscience field in previous studies. It has been found that the mechanical strengthening can be extended down to 3 nm, much smaller than the previously reported most substantial sizes of nanometals, which enlarges the regime of conventional Hall-Petch relationship, implying the significance of rDAC XRD techniques to material science.

<table border="1" fo:keep-together.within-page="1" fo:keep-with-next.within-page="always">
	<tbody>
		<tr>
			<td>20 nm Ni</td>
			<td>Nanomaterialstore</td>
			<td>SN1601</td>
			<td>Flammable</td>
		</tr>
		<tr>
			<td>3 nm Ni</td>
			<td>nanoComposix</td>
			<td></td>
			<td>Flammable</td>
		</tr>
		<tr>
			<td>40, 70, 100, 200, 500 nm Ni</td>
			<td>US nano</td>
			<td>US1120</td>
			<td>Flammable</td>
		</tr>
		<tr>
			<td>Absolute ethanol</td>
			<td></td>
			<td></td>
			<td>as the solution to make 8 nm Ni</td>
		</tr>
		<tr>
			<td>Absolute isopropanol</td>
			<td></td>
			<td></td>
			<td>as the solution to make 12 nm Ni</td>
		</tr>
		<tr>
			<td>Amorphous boron powder</td>
			<td>alfa asear</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Copper mesh</td>
			<td>Beijing Zhongjingkeyi Technology Co., Ltd.</td>
			<td></td>
			<td>TEM grid</td>
		</tr>
		<tr>
			<td>Epoxy glue</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Ethanol</td>
			<td></td>
			<td></td>
			<td>clean experimental setup</td>
		</tr>
		<tr>
			<td>Focused ion beam</td>
			<td>FEI</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Glass slide</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Glue tape</td>
			<td>Scotch</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Kapton</td>
			<td>DuPont</td>
			<td></td>
			<td>Polyimide film material</td>
		</tr>
		<tr>
			<td>Laser drilling machine</td>
			<td></td>
			<td></td>
			<td>located in high pressure lab of ALS</td>
		</tr>
		<tr>
			<td>Monochromatic synchrotron X-ray</td>
			<td>Beamline 12.2.2, Advanced Light Source (ALS), Lawrence Berkeley National Laboratory</td>
			<td></td>
			<td>X-ray energy: 25-30 keV</td>
		</tr>
		<tr>
			<td>Optical microscope</td>
			<td>Leica</td>
			<td></td>
			<td>to mount the gasket and load samples</td>
		</tr>
		<tr>
			<td>Pt powder</td>
			<td>thermofisher</td>
			<td>38374</td>
			<td></td>
		</tr>
		<tr>
			<td>Reaction kettle</td>
			<td>Xian Yichuang Co.,Ltd.</td>
			<td></td>
			<td>50 mL</td>
		</tr>
		<tr>
			<td>Sand paper</td>
			<td></td>
			<td></td>
			<td>from 400 mesh to 1000 mesh</td>
		</tr>
		<tr>
			<td>Transmission Electron Microscopy</td>
			<td>FEI</td>
			<td></td>
			<td>Titan G2 60-300</td>
		</tr>
		<tr>
			<td>Two-dimension image plate</td>
			<td>ALS, BL 12.2.2</td>
			<td></td>
			<td>mar 345</td>
		</tr>
	</tbody>
</table>

determining the mechanical strength of ultra-fine-grained metals

The mechanical strengthening of metals is the long-standing challenge and popular topic of materials science in industries and academia. The size dependence of the strength of the nanometals has been attracting a lot of interest. However, characterizing the strength of materials at the lower nanometer scale has been a big challenge because the traditional techniques become no longer effective and reliable, such as nano-indentation, micropillar compression, tensile, etc. The current protocol employs radial diamond-anvil cell (rDAC) X-ray diffraction (XRD) techniques to track differential stress changes and determine the strength of ultrafine metals. It is found that ultrafine nickel particles have more significant yield strength than coarser particles, and the size strengthening of nickel continues down to 3 nm. This vital finding immensely depends on effective and reliable characterizing techniques. The rDAC XRD method is expected to play a significant role in studying and exploring nanomaterial mechanics.

Under hydrostatic compression, unrolled X-ray diffraction lines should be straight, not curved. However, under non-hydrostatic pressure, the curvature (ellipticity of the XRD rings, which translates into the non-linearity of the lines plotted along the azimuth angle) significantly increases ultrafine-grained-nickel at similar pressures (Figure 4). At a similar pressure, the differential strain of the 3 nm sized nickel is the highest. The mechanical strength results (stress-strain curves) are...

Watch this Scientific Journal Video about Determining the Mechanical Strength of Ultra-Fine-Grained Metals at JoVE.com

Determining the Mechanical Strength of Ultra-Fine-Grained Metals

The protocol presented here describes the high-pressure radial diamond-anvil-cell experiments and analyzing the related data, which are essential for obtaining the mechanical strength of the nanomaterials with a significant breakthrough to the traditional approach.

The mechanical strengthening of metals is the long-standing challenge and popular topic of materials science in industries and academia. The size ...

Research

Education

JoVE Core

JoVE Journal

Mechanical Engineering

Engineering

Unit 1

Concept of Stress

SCIENTISTS IN ACTION

Determining 3D Flow Fields via Multi-camera Light Field Imaging

멀티 카메라 라이트 필드 영상을 통해 3D 흐름 필드를 결정하는

In the field of fluid mechanics, the resolution of computational schemes has outpaced experimental methods and widened the gap between predicted and ...

연구

공학

Fast Imaging Technique to Study Drop Impact Dynamics of Non-Newtonian Fluids

비 뉴턴 유체의 낙하 충격 역학을 연구하기 위해 빠른 이미징 기술

In the field of fluid mechanics, many dynamical processes not only occur over a very short time interval but also require high spatial resolution for ...

Casting Protocols for the Production of Open Cell Aluminum Foams by the Replication Technique and the Effect on Porosity

복제 기술에 의해 오픈 셀 알루미늄 발포체의 생산 및 기공의 효과에 대한 프로토콜 캐스팅

Metal foams are interesting materials from both a fundamental understanding and practical applications point of view. Uses have been proposed, and in many ...

Experiments on Ultrasonic Lubrication Using a Piezoelectrically-assisted Tribometer and Optical Profilometer

초음파 윤활에 대한 실험은 압전 이용한 마찰 계 및 광학 프로파일로 사용

Friction and wear are detrimental to engineered systems. Ultrasonic lubrication is achieved when the interface between two sliding surfaces is vibrated at ...

Indirect Fabrication of Lattice Metals with Thin Sections Using Centrifugal Casting

One of the typical methods to manufacture 3D lattice metals is the direct-metal additive manufacturing (AM) process such as Selective Laser Melting (SLM) ...

Data Acquisition Protocol for Determining Embedded Sensitivity Functions

데이터 수집 프로토콜 임베디드 감도 기능을 결정하는

The effectiveness of many structural health monitoring techniques depends on the placement of sensors and the location of input forces. Algorithms for ...

A Robotic Platform to Study the Foreflipper of the California Sea Lion

로봇 플랫폼은 캘리포니아 바다 사자의 Foreflipper를 공부하기

The California sea lion (Zalophus californianus), is an agile and powerful swimmer. Unlike many successful swimmers (dolphins, tuna), they generate most ...

Ice Generation and the Heat and Mass Transfer Phenomena of Introducing Water to a Cold Bath of Brine

얼음 생성과 소금물의 차가운 목욕을 소개 물의 열 및 물질 전달 현상

We demonstrate a method for the study of the heat and mass transfer and of the freezing phenomena in a subcooled brine environment. Our experiment showed ...

Characterization of Ultra-fine Grained and Nanocrystalline Materials Using Transmission Kikuchi Diffraction

전송 키쿠치 회절을 사용하여 울트라 미세 그레인과 나노 결정 재료의 특성

One of the challenges in microstructure analysis nowadays resides in the reliable and accurate characterization of ultra-fine grained (UFG) and ...

A Novel Biaxial Testing Apparatus for the Determination of Forming Limit under Hot Stamping Conditions

The hot stamping and cold die quenching process is increasingly used to form complex shaped structural components of sheet metals. Conventional ...