Name: direct comparison of hyperspectral stimulated raman scattering and coherent anti-stokes raman scattering microscopy for chemical imaging
Uploaded: 2022-04-28T13:20:00
Description: Watch this Scientific Journal Video about Direct Comparison of Hyperspectral Stimulated Raman Scattering and Coherent Anti-Stokes Raman Scattering Microscopy for Chemical Imaging at JoVE.com

This research was supported by the Purdue University Department of Chemistry startup fund.

1. Instrumental setup for hyperspectral CRS imaging
NOTE: The generation of CRS signal requires the use of high-power (i.e., class 3B or class 4) lasers. Safety protocols must be addressed and proper personal protective equipment (PPE) must be worn at all times when working at such high peak powers. Consult proper documentation before experimentation. This protocol focuses on designing the beam path, chirping the femtosecond pulses, and optimizing imaging conditions. A general o...

The protocol presented here describes the construction of a multimodal CRS microscope and the direct comparison between CARS and SRS imaging. For the microscope construction, the critical steps are spatial and temporal beam overlapping and beam size optimization. It is recommended to use a standard sample such as DMSO before the biological imaging for optimizing SNR and calibrating Raman shifts. Direct comparison between CARS and SRS images reveals that CARS has a better spatial resolution, while SRS gives better spectra...

The Raman scattering phenomenon was first observed in 1928 by C. V. Raman1. When an incident photon is interacting with a sample, an inelastic scattering event can spontaneously occur, in which the energy change of the photon matches a vibrational transition of the analyzed chemical species. This process does not require the use of a chemical tag, making it a versatile, label-free tool for chemical analysis while minimizing sample perturbation. Despite its advantages, spontaneous Raman scattering suffers from a low scattering cross-section (typically 1011 lower than the infrared [IR] absorption cross-section), which necessitates long acquisition times for analysis2. Thus, the quest for increasing the sensitivity of the Raman scattering process is essential in pushing Raman technologies for real-time imaging.
One effective way to greatly enhance the sensitivity of Raman scattering is through coherent Raman scattering (CRS) processes, for which two laser pulses are typically used to excite molecular vibrational transitions3,4. When the photon energy difference between the two lasers matches the vibrational modes of sample molecules, strong Raman signals will be generated. The two most commonly used CRS processes for imaging are coherent anti-Stokes Raman scattering (CARS) and stimulated Raman scattering (SRS)5. Over the past two decades, technological developments have advanced CARS and SRS microscopy techniques to become powerful tools for label-free quantification and elucidation of chemical changes in biological samples.
Chemical imaging by CARS microscopy can be dated to 1982 when laser scanning was first applied to acquire CARS images, demonstrated by Duncan et al6. The modernization of CARS microscopy was greatly accelerated after the wide applications of laser scanning multiphoton fluorescence microscopy7. Early work from the Xie group using high repetition rate lasers has transitioned CARS to be a high-speed, label-free, chemical imaging platform for the characterization of molecules in biological samples8,9,10. One of the major issues for CARS imaging is the presence of a nonresonant background, which reduces the image contrast and distorts the Raman spectrum. Many efforts have been made to either reduce the nonresonant background11,12,13,14,15 or to extract resonant Raman signals from the CARS spectra16,17. Another advancement that has greatly advanced the field is hyperspectral CARS imaging, which allows for spectral mapping at each image pixel with improved chemical selectivity18,19,20,21.
Stimulated Raman scattering (SRS) is a younger imaging technology than CARS, although it was discovered earlier22. In 2007, SRS microscopy was reported using a low repetition rate laser source23. Soon, several groups demonstrated high-speed SRS imaging using high repetition rate lasers24,25,26. One of the major advantages of SRS microscopy over CARS is the absence of the nonresonant background27, although other backgrounds such as cross-phase modulation (XPM), transient absorption (TA), two-photon absorption (TPA), and photothermal (PT) effect, may occur with SRS28. In addition, the SRS signal and sample concentration have linear relationships, unlike CARS, which has a quadratic signal-concentration dependence29. This simplifies chemical quantification and spectral unmixing. Multicolor and hyperspectral SRS has evolved in different forms30,31,32,33,34,35,36, with spectral focusing being one of the most popular approaches for chemical imaging37,38.
Both CARS and SRS require the focusing of the pump and Stokes laser beams onto the sample to match the vibrational transition of the molecules for signal excitation. CARS and SRS microscopes also share a lot in common. However, the physics underlying these two processes, and signal detections involved in these microscopy technologies have disparities3,39. CARS is a parametric process that does not have net photon-molecule energy coupling3. SRS, however, is a nonparametric process, and contributes to energy transfer between photons and molecular systems27. In CARS, a new signal at anti-Stokes frequency is generated, while SRS manifests as the energy transfer between the pump and Stokes laser beams.
CARS signal satisfies Eq (1)28.
<img alt="Equation 1" src="/files/ftp_upload/63677/63677eq1v2.png" style="margin: auto;" /> &#160; &#160; (1)
Meanwhile, SRS signal can be written as Eq (2)28.
<img alt="Equation 1" src="/files/ftp_upload/63677/63677eq2v2.png" style="margin: auto;" />&#160; &#160; (2)
Here, Ip, Is, ICARS, and &#916;ISRS are the intensities of the pump beam, Stokes beam, CARS signal, and SRS signals, respectively.&#160;&#967;(3) is the third-order nonlinear optical susceptibility of the sample, and is a complex value composed of real and imaginary parts.
These equations express the spectral profiles and signal-concentration dependence of CARS and SRS. Differences in physics result in disparate detection schemes for these two microscopy technologies. Signal detection in CARS usually involves spectral separation of newly generated photons and detection using a photomultiplier tube (PMT) or charge-coupled device (CCD); for SRS, the energy exchange between the pump and Stokes beams is usually measured by high-speed intensity modulation using an optical modulator and demodulation using a photodiode (PD) paired with a lock-in amplifier.
Although many technological developments and applications have been published in recent years in both CARS and SRS fields, no systematic comparisons of the two CRS techniques have been performed on the same platform, especially for hyperspectral CARS and SRS microscopy. Direct comparisons in sensitivity, spatial resolution, spectral resolution, and chemical separation capabilities would allow biologists to select the best modality for chemical quantification. In this protocol, detailed steps to construct a multimodal imaging platform with both hyperspectral CARS and SRS modalities based on a femtosecond laser system and spectral focusing are provided. The two techniques have been compared in the forward direction for spectral resolution, detection sensitivity, spatial resolution, and imaging contrasts of cells.

<table border="1" fo:keep-together.within-page="1" fo:keep-with-next.within-page="always">
	<tbody>
		<tr>
			<td>2D galvo scanner set</td>
			<td>Thorlabs</td>
			<td>GVS002</td>
			<td></td>
		</tr>
		<tr>
			<td>Acousto-optic modulator</td>
			<td>Isomet</td>
			<td>M1205-P80L-0.5</td>
			<td></td>
		</tr>
		<tr>
			<td>AOM driver</td>
			<td>Isomet</td>
			<td>532B-2</td>
			<td></td>
		</tr>
		<tr>
			<td>Data acquisition card</td>
			<td>National Instruments</td>
			<td>PCle 6363</td>
			<td>Custom ordered filter (980 sp)</td>
		</tr>
		<tr>
			<td>Delay stage</td>
			<td>Zaber</td>
			<td>X-LSM050A</td>
			<td></td>
		</tr>
		<tr>
			<td>Deuterium oxide</td>
			<td>Millipore Sigma</td>
			<td>151882-100G</td>
			<td></td>
		</tr>
		<tr>
			<td>Dichroic mirror for beam combination</td>
			<td>Thorlabs</td>
			<td>DMLP1000</td>
			<td></td>
		</tr>
		<tr>
			<td>Dichroic mirror for signal separation</td>
			<td>Semrock</td>
			<td>FF776-Di01-25x36</td>
			<td></td>
		</tr>
		<tr>
			<td>DMSO</td>
			<td>MiliporeSigma</td>
			<td>200-664-3</td>
			<td></td>
		</tr>
		<tr>
			<td>MIA PaCa 2 Cells</td>
			<td>ATCC</td>
			<td>CRL-1420</td>
			<td></td>
		</tr>
		<tr>
			<td>Femtosecond laser system</td>
			<td>Spectral Physics</td>
			<td>InSightX3+</td>
			<td></td>
		</tr>
		<tr>
			<td>Filter for CARS</td>
			<td>Chroma</td>
			<td>AT655/30m</td>
			<td></td>
		</tr>
		<tr>
			<td>Filter for SRS</td>
			<td>Chroma</td>
			<td>ET980sp</td>
			<td></td>
		</tr>
		<tr>
			<td>Function generator</td>
			<td>Rigol</td>
			<td>DG1022Z</td>
			<td></td>
		</tr>
		<tr>
			<td>Glass rods</td>
			<td>Lattice Electro Optics</td>
			<td>SF-57</td>
			<td></td>
		</tr>
		<tr>
			<td>Half-wave plate</td>
			<td>Newport</td>
			<td>10RP02-51; 10RP02-46</td>
			<td></td>
		</tr>
		<tr>
			<td>LabVIEW 2020</td>
			<td>National Instruments</td>
			<td></td>
			<td>This is the image acquisition software</td>
		</tr>
		<tr>
			<td>Lock-in amplifier</td>
			<td>Zurich Instrument</td>
			<td>HF2LI</td>
			<td></td>
		</tr>
		<tr>
			<td>Microscope housing</td>
			<td>Olympus</td>
			<td>BX51W1</td>
			<td></td>
		</tr>
		<tr>
			<td>Objective lens</td>
			<td>Olympus</td>
			<td>UPLSAPO60XW</td>
			<td></td>
		</tr>
		<tr>
			<td>Origin Pro 2019b</td>
			<td>OriginLab Corporation</td>
			<td></td>
			<td>This is the spectral fitting software</td>
		</tr>
		<tr>
			<td>Oscilloscope</td>
			<td>Tektronix</td>
			<td>TBS2204B</td>
			<td></td>
		</tr>
		<tr>
			<td>Photodiode</td>
			<td>Hamamatsu</td>
			<td>S3994-01</td>
			<td></td>
		</tr>
		<tr>
			<td>PMT detector</td>
			<td>Hamamatsu</td>
			<td>H7422P-40</td>
			<td></td>
		</tr>
		<tr>
			<td>PMT voltage amplifier</td>
			<td>Advanced Research Instrument Corp.</td>
			<td>PMT4V3</td>
			<td></td>
		</tr>
		<tr>
			<td>Polarizing beamsplitter cube</td>
			<td>Thorlabs</td>
			<td>PBS255</td>
			<td></td>
		</tr>
		<tr>
			<td>Terminal block</td>
			<td>National Instruments</td>
			<td>BNC-2110</td>
			<td></td>
		</tr>
	</tbody>
</table>

direct comparison of hyperspectral stimulated raman scattering and coherent anti-stokes raman scattering microscopy for chemical imaging

Stimulated Raman scattering (SRS) and coherent anti-Stokes Raman scattering (CARS) microscopy are the most widely used coherent Raman scattering imaging technologies. Hyperspectral SRS and CARS imaging offer Raman spectral information at every pixel, which enables better separation of different chemical compositions. Although both techniques require two excitation lasers, their signal detection schemes and spectral properties are quite different. The goal of this protocol is to perform both hyperspectral SRS and CARS imaging on a single platform and compare the two microscopy techniques for imaging different biological samples. The spectral focusing method is employed to acquire spectral information using femtosecond lasers. By using standard chemical samples, the sensitivity, spatial resolution, and spectral resolution of SRS and CARS in the same excitation conditions (i.e., power at the sample, pixel dwell time, objective lens, pulse energy) are compared. The imaging contrasts of CARS and SRS for biological samples are juxtaposed and compared. The direct comparison of CARS and SRS performances would allow for optimal selection of the modality for chemical imaging.

Comparisons of the spectral resolution 
Figure 2 compares the spectral resolution of hyperspectral SRS (Figure 2A) and CARS (Figure 2B) microscopy using a DMSO sample. For the SRS spectrum, two Lorentzian functions (see protocol step 2.3) were applied to fit the spectrum, and a resolution of 14.6 cm-1 was obtained using the 2,913 cm-1 peak. For CARS, a two-peak-fitting function with a Gaus...

Watch this Scientific Journal Video about Direct Comparison of Hyperspectral Stimulated Raman Scattering and Coherent Anti-Stokes Raman Scattering Microscopy for Chemical Imaging at JoVE.com

Direct Comparison of Hyperspectral Stimulated Raman Scattering and Coherent Anti-Stokes Raman Scattering Microscopy for Chemical Imaging

This paper directly compares the resolution, sensitivity, and imaging contrasts of stimulated Raman scattering (SRS) and coherent anti-Stokes Raman scattering (CARS) integrated into the same microscope platform. The results show that CARS has a better spatial resolution, SRS gives better contrasts and spectral resolution, and both methods have similar sensitivity.

Stimulated Raman scattering (SRS) and coherent anti-Stokes Raman scattering (CARS) microscopy are the most widely used coherent Raman scattering imaging ...

Research

JoVE Journal

Chemistry

A Filter-based Surface Enhanced Raman Spectroscopic Assay for Rapid Detection of Chemical Contaminants

基于过滤器的表面增强拉曼光谱检测方法的化学污染物快速检测

We demonstrate a method to fabricate highly sensitive surface-enhanced Raman spectroscopic (SERS) substrates using a filter syringe system that can be ...

科研

化学

Preparation of Biopolymer Aerogels Using Green Solvents

生物聚合物气凝胶制备使用绿色溶剂

Although the first reports on aerogels made by Kistler1 in the 1930s dealt with aerogels from both inorganic oxides (silica and others) and biopolymers ...

Measurement of Particle Size Distribution in Turbid Solutions by Dynamic Light Scattering Microscopy

通过动态光散射显微镜混浊解决方案粒度分布的测定

A protocol for measuring polydispersity of concentrated polymer solutions using dynamic light scattering is described. Dynamic light scattering is a ...

A Novel Technique for Raman Analysis of Highly Radioactive Samples Using Any Standard Micro-Raman Spectrometer

一种新技术用于拉曼分析高放射性样品使用任何标准的微拉曼光谱仪

A novel approach for the Raman measurement of nuclear materials is reported in this paper. It consists of the enclosure of the radioactive sample in a ...

Monitoring the Effects of Illumination on the Structure of Conjugated Polymer Gels Using Neutron Scattering

利用中子散射监测光照对共轭高分子凝胶结构的影响

We demonstrate a protocol to effectively monitor the gelation process of a high concentration solution of conjugated polymer both in the presence and ...

Observation and Analysis of Blinking Surface-enhanced Raman Scattering

闪烁表面增强拉曼散射的观测与分析

From a single molecule at a silver nanoaggregate junction, blinking surface-enhanced Raman scattering (SERS) is observed. Here, a protocol is presented on ...

Application of Voltage in Dynamic Light Scattering Particle Size Analysis

电压在动态光散射粒子尺寸分析中的应用

Dynamic light scattering (DLS) is a common method for characterizing the size distribution of polymers, proteins, and other nano- and microparticles. ...

Ultrafast Time-resolved Near-IR Stimulated Raman Measurements of Functional &#960;-conjugate Systems

Ultrafast Time-resolved Near-IR Stimulated Raman Measurements of Functional ÃƒÂÃ¢â€šÂ¬-conjugate Systems

超快时间解析近红外刺激拉曼测量功能 +偶联系统

Femtosecond time-resolved stimulated Raman spectroscopy is a promising method of observing the structural dynamics of short-lived transients with near ...

Neutron Crystallography Data Collection and Processing for Modelling Hydrogen Atoms in Protein Structures

中子晶体学数据收集和处理，用于蛋白质结构中氢原子的建模

Neutron crystallography is a structural technique that allows determination of hydrogen atom positions within biological macromolecules, yielding ...

﻿Analyzing the Heterogeneous Performance of Single Nanoparticles with Electrochemical Methods

Tracking Electrochemistry on Single Nanoparticles with Surface-Enhanced Raman Scattering Spectroscopy and Microscopy

Tracking Electrochemistry on Single Nanoparticles with Surface-Enhanced Raman Scattering Spectroscopy and Microscopy (Video) | JoVE 

用表面增强拉曼散射光谱和显微镜跟踪单个纳米颗粒的电化学

Studying electrochemical reactions on single nanoparticles is important to understand the heterogeneous performance of individual nanoparticles. This ...