microfluidic-pneumatic-cages-novel-approach-for-chip-crystal-trapping

Microfluidic Pneumatic Cages: A Novel Approach for In-chip Crystal Trapping, Manipulation and Controlled Chemical Treatment

The precise localization and controlled chemical treatment of structures on a surface are significant challenges for common laboratory technologies. ...

microfluidic-based-synthesis-covalent-organic-frameworks-cofs-tool

Microfluidic-based Synthesis of Covalent Organic Frameworks (COFs): A Tool for Continuous Production of COF Fibers and Direct Printing on a Surface

Covalent Organic Frameworks (COFs) are a class of porous covalent materials which are frequently synthesized as unprocessable crystalline powders. The ...

Institut de Ciència de Materials de Barcelona

Institut de Ciència de Materials de Barcelona (ICMAB-CSIC)

This article presents the fabrication and characterisation of a high-speed detection micro-Coulter counter with two-dimensional (2D) adjustable aperture and differential impedance detection. The developed device has been fabricated from biocompatible and transparent materials (polymer and glass) and uses the principle of hydrodynamic focusing in two dimensions. The use of a conductive solution for the sample flux and non-conductive solutions for the focalising fluxes provides an adjustable sample flow where particles are aligned and the resistive response concentrated, consequently enhancing the sensitivity and versatility of the device. High-speed counting of 20 microm polystyrene particles and 5 microm yeast cells with a rate of up to 1,000 particles/s has been demonstrated. Two-dimensional focusing conditions have been used in devices with physical cross-sectional areas of 180 microm x 65 microm and 100 microm x 43 microm, respectively, in which particles resulted undetectable in the absence of focusing. The 2D-focusing conditions have provided, in addition, increased detection sensitivity by a factor of 1.6 as compared to 1D-focusing conditions.

High-speed particle detection in a micro-Coulter counter with two-dimensional adjustable aperture.

In this paper we discuss the fabrication and characterization of three dimensional (3D) micro- and nanoelectrodes with the goal of using them for extra- and intracellular studies. Two different types of electrodes will be described: high aspect ratio microelectrodes for studying the communication between cells and ultimately for brain slice recordings and small nanoelectrodes for highly localized measurements and ultimately for intracellular studies. Electrical and electrochemical characterization of these electrodes as well as the results of PC12 cell differentiation on chip will be presented and discussed.

Fabrication and characterization of 3D micro- and nanoelectrodes for neuron recordings.

This work describes the electrical investigation of paclitaxel-treated HeLa cells using a custom-made microfluidic biosensor for whole cell analysis in continuous flow. We apply the method of differential electrical impedance spectroscopy to treated HeLa cells in order to elucidate the changes in electrical properties compared with non-treated cells. We found that our microfluidic system was able to distinguish between treated and non-treated cells. Furthermore, we utilize a model for electrical impedance spectroscopy in order to perform a theoretical study to clarify our results. This study focuses on investigating the changes in the electrical properties of the cell membrane caused by the effect of paclitaxel. We observe good agreement between the model and the obtained results. This establishes the proof-of-concept for the application in cell drug therapy.

Study of Paclitaxel-Treated HeLa Cells by Differential Electrical Impedance Flow Cytometry.

The effect of diffusion-controlled microfluidic conditions in the very initial stages of a far-from-equilibrium self-assembly process on the evolution of aggregate chirality in a multicomponent supramolecular system is shown.

Milliseconds Make the Difference in the Far-from-Equilibrium Self-Assembly of Supramolecular Chiral Nanostructures.

A microfluidic chip has been used to prepare fibres of a porous polymer with high structural order, setting a precedent for the generation of a wide variety of materials using this reagent mixing approach that provides unique materials not accessible easily through bulk processes. The reaction between 1,3,5-tris(4-aminophenyl)benzene and 1,3,5-benzenetricarbaldehyde in acetic acid under continuous microfluidic flow conditions leads to the formation of a highly crystalline and porous covalent organic framework (hereafter denoted as ), consisting of fibrillar micro-structures, which have mechanical stability that allows for direct drawing of objects on a surface.

Romen Rodriguez-Trujillo

Institut de Ciència de Materials de Barcelona

Microfluidic Pneumatic Cages: A Novel Approach for In-chip Crystal Trapping, Manipulation and Controlled Chemical Treatment

Microfluidic-based Synthesis of Covalent Organic Frameworks (COFs): A Tool for Continuous Production of COF Fibers and Direct Printing on a Surface