scattering-and-absorption-of-light-in-planetary-regoliths

Scattering And Absorption of Light in Planetary Regoliths

Theoretical, numerical, and experimental methods are presented for multiple scattering of light in macroscopic discrete random media of densely-packed ...

University of Helsinki

A supercontinuum light source was incorporated into a custom-built scanning white-light interferometer. This light source based on a Nd:YAG pumped microstructured optical fiber exhibits 1.21+/-0.10 microm temporal coherence length. The device operation was validated by characterizing the step height on a microelectromechanical system component. The measured step height- 7.027+/-0.020 microm-agreed with results obtained by employing traditional light sources: a halogen lamp and a white light-emitting diode. The new light source features high output intensity of 20-35 mW, which is beneficial when measuring low-reflectivity samples. As the supercontinuum light source may be modulated at frequencies exceeding 10 MHz, it holds potential for stroboscopic dynamic measurements.

Scanning white-light interferometry with a supercontinuum source.

Scratch resistance (SR) of externally plasticized hydroxypropyl methylcellulose (HPMC) films intended for tablet film coatings was studied. Special attention was paid to effects of short-term aging and ultraviolet (UV) treatment on the SR properties of these films. Controlled scratching of the films was performed with a Lloyd LRX materials tester featuring a spherical steel tip. Scratch surface profiles were measured by scanning white light interferometry (SWLI). The influence of using an external plasticizer on the SR was studied by comparing scratch dimensions in non-plasticized films to samples plasticized either with glycerol or polyethylene glycol (PEG) 400. The study demonstrates that both the amount and type of plasticizer influences the SR of aqueous HPMC films. It also shows that SWLI can quantitatively evaluate the effect of plasticizer content and aging on the SR of pharmaceutical films. This knowledge could be used to optimize pharmaceutical film coating formulations.

Scratch resistance of plasticized hydroxypropyl methylcellulose (HPMC) films intended for tablet coatings.

Stroboscopic scanning white light interferometry (SSWLI) allows precise three dimensional (3D) measurements of oscillating samples. Commercial SSWLI devices feature limited pulsing frequency. To address this issue we built a 400-620 nm wideband 150 mW light source whose 1.6 µm wide interferogram is without side peaks. The source combines a non-phosphor white LED with a cyan LED. We measured a calibration artifact with 10 nm precision and obtained 40 nm precision when measuring the 3D profile of a capacitive micromachined ultrasonic transducer membrane operating at 2.72 MHz. This source is compatible with solid state technology.

Stroboscopic scanning white light interferometry at 2.7 MHz with 1.6 µm coherence length using a non-phosphor LED source.

We showed that scanning white light interferometry (SWLI) can provide nanometer depth resolution in 3D topographic analysis of electrospun drug-loaded nanofibrous mats without sample preparation. The method permits rapidly investigating geometric properties (e.g. fiber diameter, orientation and morphology) and surface topography of drug-loaded nanofibers and nanomats. Electrospun nanofibers of a model drug, piroxicam (PRX), and hydroxypropyl methylcellulose (HPMC) were imaged. Scanning electron microscopy (SEM) served as a reference method. SWLI 3D images featuring 29 nm by 29 nm active pixel size were obtained of a 55 μm × 40 μm area. The thickness of the drug-loaded non-woven nanomats was uniform, ranging from 2.0 μm to 3.0 μm (SWLI), and independent of the ratio between HPMC and PRX. The average diameters (n=100, SEM) for drug-loaded nanofibers were 387 ± 125 nm (HPMC and PRX 1:1), 407 ± 144 nm (HPMC and PRX 1:2), and 290 ± 100 nm (HPMC and PRX 1:4). We found advantages and limitations in both techniques. SWLI permits rapid non-contacting and non-destructive characterization of layer orientation, layer thickness, porosity, and surface morphology of electrospun drug-loaded nanofibers and nanomats. Such analysis is important because the surface topography affects the performance of nanomats in pharmaceutical and biomedical applications.

Nanometer depth resolution in 3D topographic analysis of drug-loaded nanofibrous mats without sample preparation.

We present work on matching 2-mm-thick wires using optical 3D imaging methods. Marks on such small surfaces are difficult to match using a comparison microscope as this 2D imaging method does not provide height data about the sample surface. Moreover, these 2D microscopy images may be affected by illumination. Hence, the reference and investigated sample should be present at the same time. We employed scanning white light interferometry and confocal microscopy to provide quantitative 3D profiles for reliable comparison of samples that are unavailable for simultaneous analysis. We show that 3D profiling offers a solution by allowing illumination-independent sample comparison. We correctly identified 74 of 80 profiles using consecutive matching striae (CMS) criteria, and we were able to match samples based on profiles measured using different 3D imaging devices. The results suggest that the used methods allow matching cutter marks on thin wires, which has been difficult previously. 

Identifying diagonal cutter marks on thin wires using 3D imaging.

The developments in printing technologies allow fabrication of micron-size nano-layered delivery systems to personal specifications. In this study we fabricated layered polymer structures for drug-delivery into a microfluidic channel and aimed to interferometrically assure their topography and adherence to each other. We present a scanning white light interferometer (SWLI) method for quantitative assurance of the topography of the embedded structure. We determined rapidly in non-destructive manner the thickness and roughness of the structures and whether the printed layers containing polymers or/and active pharmaceutical ingredients (API) adhere to each other. This is crucial in order to have predetermined drug release profiles. We also demonstrate non-invasive measurement of a polymer structure in a microfluidic channel. It shown that traceable interferometric 3D microscopy is a viable technique for detailed structural quality assurance of layered drug-delivery systems. The approach can have impact and find use in a much broader setting within and outside life sciences. 

Rapid interferometric imaging of printed drug laden multilayer structures.

We present quantitative three dimensional images of grooves on a writable Blu-ray Disc based on a single objective Mirau type interferometric microscope, enhanced with a microsphere which is considered as a photonic nanojet source. Along the optical axis the resolution of this microsphere assisted interferometry system is a few nanometers while the lateral resolution is around 112 nm. To understand the physical phenomena involved in this kind of imaging we have modelled the interaction between the photonic jet and the complex disc surface. Agreement between simulation and experimental results is demonstrated. We underline that although the ability of the microsphere to generate a photonic nanojet does not alone explain the resolution of the interferometer, the nanojet can be used to try to understand the imaging process. To partly explain the lateral super-resolution, the potential role of coherence is illustrated. The presented modality may have a large impact on many fields from bio-medicine to nanotechnology.

Ivan Kassamakov

Department of Physics

University of Helsinki

Scattering And Absorption of Light in Planetary Regoliths

Ivan Kassamakov

.css-o250i3{font-size:18px;font-family:Open Sans,sans-serif;line-height:21.6px;}Department of Physics

University of Helsinki

Scattering And Absorption of Light in Planetary Regoliths

Department of Physics