这项研究得到了ZonMw的资助，作为LSH 2Treat计划（436001003）和荷兰肾脏基金会（14a2d507）的一部分。N.A.K.感谢欧洲研究理事会（851960）的支持。我们感谢荷兰科学研究组织（024.003.013）资助的引力计划"材料驱动再生"。

作者没有什么可透露的。

此处描述的生物反应器允许系统地评估剪切应力和循环拉伸对管状可重新吸附脚手架的炎症和组织再生的个体贡献和综合影响。这种方法还使血管构造能够进行各种各样的分析，在具有代表性的结果部分就说明了这一点。这些结果表明，不同的血液机载系统（即剪切和拉伸的不同组合）对 TEVG 结构的生长和改造都有独特的影响。这些见解通过这个体外平台收集，有助于优化新开发的原地 TEVG 的脚?...

心血管组织工程（TE）正在作为替代治疗选择，目前使用的永久心血管假肢（如血管移植，心脏瓣膜置换），这是不理想的大组患者1，2，3，4。许多抢手的应用包括组织工程血管移植 （TEVG）5，6和心脏瓣膜 （TEHV）7，8.最常见的是，心血管TE方法利用可重新吸收的生物材料（无论是天然的还是合成的），作为新组织形成的有启发性的支架。新组织的形成可以完全在体外设计，通过用细胞播种脚手架，并在植入前在生物反应器中培养（体外TE）9、10、11或直接就地植入，在原位植入合成脚手架时无需预先培养，以诱导体内（原位TE）12、13、14等新组织的形成。对于体外和原位心血管TE方法，成功的功能再生主要取决于宿主对植入结构的免疫反应和适当的生物力学负荷。
生物力学负荷对心血管TE的重要性是众所周知的。在心血管植入物中，填充脚手架的细胞暴露于循环拉伸和剪切压力，这些压力是血友病环境引起的。许多研究已经报告了（循环）拉伸对基质成分形成的刺激作用，如胶原蛋白16，17，18，19，糖氨酸（GAGs）20，和弹性蛋白21，22，由各种细胞类型。例如，黄等人证明，双轴拉伸利用血管生物反应器23，提高了胶原蛋白和弹性蛋白在体外特威格斯中的沉积和组织。虽然重点通常在于拉伸作为主要负载，但这些研究通常使用流驱动的生物反应器，其中样本也暴露在剪切流中。虽然对剪切应力对3D组织形成和炎症的孤立影响知之甚少，但提供了一些数据。例如，Hinderer等人和Eoh等人证明，剪切流除了3D脚手架微结构外，对于人类血管平滑肌肉细胞在体外模型系统24、25中形成成熟的弹性蛋白非常重要。总之，这些发现说明了环伸和剪切应激对心血管TE的相关性。
TE植入物成败的另一个重要决定因素是宿主对植入移植物26的免疫反应。这对于物质驱动的原位TE策略尤其重要，它实际上依赖于对脚手架的急性炎症反应来启动细胞流入和内源性组织形成和重塑的后续过程。巨噬菌体是功能组织再生的关键启动器，28、29、30等多项研究表明。类似于伤口愈合，组织的再生是由巨噬细胞和组织产生细胞之间的寄生虫信号，如成纤维细胞和肌纤维细胞31，32，33。除了协调新的组织沉积外，巨噬细胞还参与外来脚手架材料34、35的主动吸收。因此，体外对生物材料的宏年反应已被确定为植入物36、37、38体内成功的预测参数。
植入式脚手架的宏观反应取决于脚手架的设计特征，如材料组成和微观结构35，39，40。除了脚手架属性外，对脚手架及其与肌纤维细胞的相声的宏法响应也受到血液动力载荷的影响。例如，环状拉伸被证明是巨噬细胞表型41，42，43，44和细胞因子43，44，45，46在3D电子喷支架分泌物的重要调节剂。Battiston等人利用巨噬细胞和血管平滑肌肉细胞的共培养系统证明，巨噬细胞的存在导致弹性蛋白和GAG水平增加，中度循环拉伸水平（1.07-1.10）刺激胶原蛋白I和弹性蛋白47的沉积。在以往的著作中，我们已经证明剪切应力是单核细胞招募到3D电喷支架48，49，剪切应力和循环拉伸影响人类单核细胞和间质频闪细胞50之间的寄生虫信号的重要决定因素。Fahy等人证明，剪切流增加了人类单核细胞51的亲炎细胞因子的分泌。
综合起来，上述证据表明，对血液机载荷的充分理解和控制对心血管TE至关重要，因此必须考虑炎症反应来实现这一点。许多生物反应器以前曾被描述为体外52，53，54，55，56，57，58或前体内59，60，61心血管组织培养。然而，所有这些系统都旨在尽可能模仿生理血液机载量条件。虽然这在体外创建心血管组织或维持前体内培养物方面具有很高的价值，但此类系统不允许系统地研究个体线索的个体影响。这是因为在这些生物反应器中应用循环拉伸和剪切应力是由相同的加压流驱动的，而加压流与它们有着内在的联系。虽然用于精确多提示机械操作的微系统已用于 2D 基材62或 3D 水凝胶设置63，64，但此类设置不允许纳入弹性 3D 生物材料脚手架。
在这里，我们介绍了管状生物反应器系统的应用，该系统独特地实现了剪切应力和循环拉伸的脱钩，并有助于机械地研究其个体和组合效应。该系统允许测试各种组织工程血管移植物（例如，合成或自然起源，不同的微结构，各种孔隙）。为了有效地将剪切应力和拉伸的应用脱钩，生物反应器使用的关键概念是（1） 使用独特的泵系统分离剪切应力和拉伸控制，（2） 以计算驱动尺寸的"从内到外"方式刺激脚手架。通过使用流泵将流量应用于管状脚手架的外表面，而脚手架的周长则通过使用单独的应变泵来扩展安装脚手架的硅胶管。硅胶管和包含构造的玻璃管的尺寸是使用计算流体动力学模拟仔细选择和验证的，以确保脚手架上的剪切应力（由于流量）和环状拉伸（由于管膨胀）不会显著影响彼此。这种从内到外的设计有几个实用的理由。如果拉伸由发光流体压力（类似于生理负荷）施加，则固有要求样品设计无泄漏。此外，拉伸样品所需的压力将完全由样品刚度决定，样本刚度可能因样品而异，并且随着时间的推移，很难控制样品的拉伸。这种生物反应器将组织工程移植物安装在硅胶管周围，并允许在移植物的外壁上应用壁切变应力 （WSS），并从内部给移植物加压。这样，样品之间和样品内部的同等装载条件可以保证，而且，样品允许泄漏，就像多孔血管支架19一样。这种从内到外的生物反应器是专门用来系统研究剪切和/或拉伸的影响，而不是在体外进行原生血管的工程，而传统的血管生物反应器设置更适合于此。有关生物反应器设计图纸 的图 1A-B 及其相应的 表 1， 了解生物反应器主要组件背后的功能描述和原理。
生物反应器的使用是根据我们小组最近的一系列研究证明的，其中我们调查了剪切应力和循环拉伸对可再吸附电喷支架中炎症和组织形成的个体和组合影响，用于原位心血管组织19、43、44。为此，我们使用单体或共培养中的人类巨噬细胞和肌纤维细胞来模拟原位再生级联的各个阶段。我们已经证明，人类巨噬细胞的细胞因子分泌明显受到循环拉伸和剪切应力的影响，通过parcrine信号和直接接触19、43、44，通过这些脚手架中的人类肌纤维细胞影响基质沉积和组织。值得注意的是，这些研究表明，在剪切应力和拉伸的结合应用的情况下，对组织形成和炎症的影响要么由两个负载之一主导，要么有两个负载的协同效应。这些发现说明了将两个负载脱钩以更好地了解机械环境对 TE 过程的贡献的相关性。这一理解可用于系统地优化相关血液动力负荷系统中的脚手架设计参数。此外，来自这些控制良好的环境的机械数据可以作为正在开发的数字模型的输入，以预测原位组织重塑的过程，正如最近为TEVG65或TEHV66报告的那样，以进一步提高预测能力。

<table border="1" fo:keep-together.within-page="1" fo:keep-with-next.within-page="always">
	<tbody>
		<tr >
			<td >advanced Dulbecco&#8217;s modified EagleMedium (aDMEM)</td>
			<td >Gibco</td>
			<td >12491-015</td>
			<td >cell culture medium for fibroblasts</td>
		</tr>
		<tr >
			<td >Aqua Stabil</td>
			<td >Julabo</td>
			<td >8940012</td>
			<td >prevent microorganism growth in bioreactor-hydraulic reservoir</td>
		</tr>
		<tr >
			<td >Bovine fibrinogen</td>
			<td >Sigma</td>
			<td >F8630</td>
			<td >to prepare fibrinogen gel to seed the cells on the electrospun scaffold</td>
		</tr>
		<tr >
			<td >Bovine thrombin</td>
			<td >Sigma</td>
			<td >T4648</td>
			<td >to prepare fibrinogen gel to seed the cells on the electrospun scaffold</td>
		</tr>
		<tr >
			<td >Centrifuge</td>
			<td >Eppendorf</td>
			<td >5804</td>
			<td >to spin down cells and conditioned medium</td>
		</tr>
		<tr >
			<td >Clamp scissor - &#34;kelly forceps&#34;</td>
			<td >Almedic</td>
			<td >P-422</td>
			<td >clamp the silicone tubing and apply pre-stretch to the scaffold so the scaffold can be sutured into the engraved groove (autoclave at step 1, step 7)</td>
		</tr>
		<tr >
			<td >CO2 cell culture incubators</td>
			<td >Sanyo</td>
			<td >MCO-170AIC-PE</td>
			<td >for cell culturing</td>
		</tr>
		<tr >
			<td >Compressed air reservoir</td>
			<td >Festo</td>
			<td >CRVZS-5</td>
			<td >smoothing air pressure fluctuations and create time delays for pressure build-up</td>
		</tr>
		<tr >
			<td >Custom Matlab script to calculate the maximum stretches</td>
			<td >Matlab</td>
			<td >R2017. The Mathworks, Natick, MA</td>
			<td >calculate the minimum and maximum outer diameter of the electrospun scaffold</td>
		</tr>
		<tr >
			<td >Data acquisition board</td>
			<td >National Instruments</td>
			<td >BNC-2090</td>
			<td >data processing in between amplifier system and computer</td>
		</tr>
		<tr >
			<td >Ethanol</td>
			<td >VWR</td>
			<td >VWRK4096-9005</td>
			<td >to keep sterile working conditions</td>
		</tr>
		<tr >
			<td >Fetal bovine calf serum (FBS)</td>
			<td >Greiner</td>
			<td >758087</td>
			<td >cell culture medium supplement; serum-supplement</td>
		</tr>
		<tr >
			<td >Flow culture chamber compartments, consisting of a pressure conduit with engraved grooves and small holes to apply pressure on silicone tubing, a screw thread, nose cone, top compartment with flow inlet and bottom compartment flow outlet, adapter bushing</td>
			<td >Custom made, Department of Biomedical Engineering, Eindhoven University of Technology</td>
			<td >n.a.</td>
			<td >flow culture chamber compartments (autoclave at step 1, step 7)</td>
		</tr>
		<tr >
			<td >Glass Pasteur pipet</td>
			<td >Assistant</td>
			<td >HE40567002</td>
			<td >apply vacuum on electrospun scaffold (autoclave at step 1)</td>
		</tr>
		<tr >
			<td >Glass tubes of the flow culture chamber</td>
			<td >Custon made, Equipment &#38; Prototype Center, Eindhoven University of Technology</td>
			<td >n.a.</td>
			<td >part of the flow culture chamber (clean and store in 70% ethanol, at step 1 and 7)</td>
		</tr>
		<tr >
			<td >GlutaMax</td>
			<td >Gibco</td>
			<td >35050061</td>
			<td >cell culture medium amino acid supplement, minimizes ammonia build-up</td>
		</tr>
		<tr >
			<td >High speed camera</td>
			<td >MotionScope</td>
			<td >M-5</td>
			<td >to monitor the stretch during culture; time-lapse photographs of the scaffolds are captured at a frequency of 30 Hz for 6 sec (i.e. 3 stretch cycles)</td>
		</tr>
		<tr >
			<td >High speed camera lens - Micro-NIKKOR 55mm f/2.8 - lens</td>
			<td >Nikon</td>
			<td >JAA616AB</td>
			<td >to monitor the stretch during culture; time-lapse photographs of the scaffolds are captured at a frequency of 30 Hz for 6 sec (i.e. 3 stretch cycles)</td>
		</tr>
		<tr >
			<td >Hose clip</td>
			<td >ibidi GmbH</td>
			<td >10821</td>
			<td >block medium flow (autoclave at step 1, step 7)</td>
		</tr>
		<tr >
			<td >Hydraulic reservoir with 8 screw threads for 8 flow culture chambers</td>
			<td >Custom made, Department of Biomedical Engineering, Eindhoven University of Technology</td>
			<td >n.a.</td>
			<td >to apply pressure to the silicone mounted constructs (clean outside with a paper tissue with 70% ethanol, rinse reservoir with 70% ethanol followed by demi water, at step 1 and 7)</td>
		</tr>
		<tr >
			<td >Ibidi pump system (8x) including ibidi pump, PumpControl software, fluidic unit, perfusion set (medium tubing), air pressure tubing, drying bottles with orange silica beads</td>
			<td >ibidi GmbH</td>
			<td >10902</td>
			<td >set up used to control the flow in the flow culture chambers. Note 1: the ibidi pumps were modified by the manufacturer to enable 200 mbar capacity. Note 2: can be replaced by pump system of other manufacturer, as long as same flow regimes can be applied.</td>
		</tr>
		<tr >
			<td >Knives (no.10 sterile blades, individual foil pack) and scalpel handle (stainless steel, individually wrapped)</td>
			<td >Swann Morton</td>
			<td >0301; 0933</td>
			<td >to cut the silicone tubing in the correct size for the scaffold and to cut the suture material</td>
		</tr>
		<tr >
			<td >LabVIEW Software</td>
			<td >National Instruments</td>
			<td >version 2018</td>
			<td >to control the stretch applied to the scaffolds</td>
		</tr>
		<tr >
			<td >Laminar flow biosafety cabinet with UV light</td>
			<td >Labconco</td>
			<td >302310001</td>
			<td >to ensure sterile working conditions. The UV is used to decontaminate everything that cannot be autoclaved, or touched after autoclaving</td>
		</tr>
		<tr >
			<td >Large and small petri dishes</td>
			<td >Greiner</td>
			<td >664-160</td>
			<td >for sterile working conditions</td>
		</tr>
		<tr >
			<td >L-ascorbic acid 2-phosphate (vitamin C)</td>
			<td >Sigma</td>
			<td >A8960</td>
			<td >cell culture medium supplement, important for collagen production</td>
		</tr>
		<tr >
			<td >LED light cold source KL2500</td>
			<td >Zeiss</td>
			<td >Schott AG</td>
			<td >to aid in visualization for the time lapse of the scaffolds during monitoring of the stretch</td>
		</tr>
		<tr >
			<td >Luer (female and male) locks and connectors, white luer caps</td>
			<td >ibidi GmbH</td>
			<td >various, see (https://ibidi.com/26-flow-accessories)</td>
			<td >to close or connect parts of the bioreactor and the ibidi pump (autoclave at step 1, step 7)</td>
		</tr>
		<tr >
			<td >Measuring amplifier (PICAS)</td>
			<td >PEEKEL instruments B.V.</td>
			<td >n.a.</td>
			<td >to amplify the signal from the pressure sensor and feedback to LabView</td>
		</tr>
		<tr >
			<td >Medium reservoir (large syringes 60 mL) and reservoir holders</td>
			<td >ibidi GmbH</td>
			<td >10974</td>
			<td >medium reservoir (autoclave at step 1, step 7)</td>
		</tr>
		<tr >
			<td >Medium tubing with 4.25 mm outer diameter and 1 mm inner diameter</td>
			<td >Rubber BV</td>
			<td >1805</td>
			<td >to allow for a larger flow rate, the ibidi medium tubing with larger diameter is used. Note: the part of medium tubing guided through the fluidic unit valves are the same as the default ibidi medium tubing</td>
		</tr>
		<tr >
			<td >Motion Studio Software</td>
			<td >Idtvision</td>
			<td >2.15.00</td>
			<td >to make the high speed time lapse images for stretch monitoring</td>
		</tr>
		<tr >
			<td >Needle (19G)</td>
			<td >BD Microlance</td>
			<td >301700</td>
			<td >together with thin flexible tubing used to fill the hydraulic reservoir with ultrapure water without adding air bubbles</td>
		</tr>
		<tr >
			<td >Needle driver</td>
			<td >Adson</td>
			<td >2429218</td>
			<td >to handle the needle of the nylon suture through the silicone tube (autoclave at step 1, step 7)</td>
		</tr>
		<tr >
			<td >Paper tissues</td>
			<td >Kleenex</td>
			<td >38044001</td>
			<td >for cleaning of the equipment with 70% ethanol</td>
		</tr>
		<tr >
			<td >Parafilm</td>
			<td >Sigma</td>
			<td >P7793-1EA</td>
			<td >quick fix if leakage occurs</td>
		</tr>
		<tr >
			<td >Penicillin/streptomycin (P/S)</td>
			<td >Lonza</td>
			<td >DE17-602E</td>
			<td >cell culture medium supplement; prevent bacterial contamination</td>
		</tr>
		<tr >
			<td >Phosphate Buffered Saline (PBS)</td>
			<td >Sigma</td>
			<td >P4417-100TAB</td>
			<td >for storage and washing steps (autoclave at step 1)</td>
		</tr>
		<tr >
			<td >Plastic containers (60 mL) with red screw caps</td>
			<td >Greiner</td>
			<td >206202</td>
			<td >to prepare the fibrinogen solution</td>
		</tr>
		<tr >
			<td >Pneumatic cylinder</td>
			<td >Festo</td>
			<td >AEVC-20-10-I-P</td>
			<td >to actuate the Teflon bellow (clean with a paper tissue with 70% ethanol at step 1 and 7)</td>
		</tr>
		<tr >
			<td >Polycaprolactone bisurea (PCL-BU) tubular scaffolds (3 mm inner diameter, 200 &#181;m wall thickness, 20 mm length)</td>
			<td >SyMO-Chem, Eindhoven, The Netherlands</td>
			<td >n.a.</td>
			<td >produced using electrospinning from 15% (w/w) chloroform (Sigma; 372978) polymer solutions. See Van Haaften et al Tissue Engineering Part C (2018) for more details</td>
		</tr>
		<tr >
			<td >Pressure conduit without holes (for static control)</td>
			<td >Custom made, Department of Biomedical Engineering, Eindhoven University of Technology</td>
			<td >n.a.</td>
			<td >to mount electrospun tubes on silicon tubing (autoclave at step 1, step 7)</td>
		</tr>
		<tr >
			<td >Pressure sensor and transducer</td>
			<td >BD</td>
			<td >TC-XX and P 10 EZ</td>
			<td >the air pressure going to the pneumatic actuated pump is raised until it reaches the set pressure</td>
		</tr>
		<tr >
			<td >Proportional air pressure control valve and pressure sensor</td>
			<td >Festo</td>
			<td >MPPES-3-1/8-2-010, 159596</td>
			<td >provides compressed air to the pneumatic actuated pump</td>
		</tr>
		<tr >
			<td >Roswell Park Memorial Institute 1640 (RPMI-1640)</td>
			<td >Gibco</td>
			<td >A1049101</td>
			<td >cell culture medium for monocyte/macrophage</td>
		</tr>
		<tr >
			<td >Safe lock Eppendorf tubes (1.5 mL)</td>
			<td >Eppendorf</td>
			<td >30120086</td>
			<td >multiple applications (autoclave at step 1)</td>
		</tr>
		<tr >
			<td >Sodium dodecyl sulfate solution 20%</td>
			<td >Sigma</td>
			<td >5030</td>
			<td >Used to clean materials, at a concentration of 0.1%.&#160;&#160;</td>
		</tr>
		<tr >
			<td >Silicone O-rings</td>
			<td >Technirub</td>
			<td >1250S</td>
			<td >to prevent leakage (autoclave at step 1, step 7)</td>
		</tr>
		<tr >
			<td >Silicone tubing (2.8 mm outer diameter, 400 um wall thickness)</td>
			<td >Rubber BV</td>
			<td >1805</td>
			<td >to mount the electrospun tubes on the pressure conduits (autoclave at step 1)</td>
		</tr>
		<tr >
			<td >Sterile tube (15 mL)</td>
			<td >Falcon</td>
			<td >352095</td>
			<td >multiple applications</td>
		</tr>
		<tr >
			<td >Suture, 5-0 prolene with pre-attached taper point needle</td>
			<td >Ethicon, Johnson&#38;Johnson</td>
			<td >EH7404H</td>
			<td >Prolene suture wire 5-0 (75cm length, TF taper point needle, 1/2 circle, 13 mm needle length)</td>
		</tr>
		<tr >
			<td >Syringe (24 mL)</td>
			<td >B. Braun Melsungen AG</td>
			<td >2057932</td>
			<td >to add the ultrapure water or medium to the hydraulic reservoir or flow culture chamber</td>
		</tr>
		<tr >
			<td >Syringe filter (0.2 &#181;m)</td>
			<td >Satorius</td>
			<td >17597-K</td>
			<td >to filter the fibrinogen solution</td>
		</tr>
		<tr >
			<td >T150 cell culture flask with filter cap</td>
			<td >Nunc</td>
			<td >178983</td>
			<td >to degas culture medium</td>
		</tr>
		<tr >
			<td >T75 Cell culture flask with filter cap</td>
			<td >Nunc</td>
			<td >156499</td>
			<td >to culture static control samples</td>
		</tr>
		<tr >
			<td >Teflon bellow</td>
			<td >Custom made, Department of Biomedical Engineering, Eindhoven University of Technology</td>
			<td >n.a.</td>
			<td >to load the hydraulic reservoir (clean outside with a paper tissue with 70% ethanol at step 1 and 7)</td>
		</tr>
		<tr >
			<td >Tray (stainless steel)</td>
			<td >PolarWare</td>
			<td >15-248</td>
			<td >for easy transport of the fluidic culture chambers and the bioreactor from incubator to laminar flow cabinet and back (clean with a paper tissue with 70% ethanol before and after use)</td>
		</tr>
		<tr >
			<td >Tweezers</td>
			<td >Wironit</td>
			<td >4910</td>
			<td >sterile handling of individual parts (autoclave at step 1 and 7)</td>
		</tr>
		<tr >
			<td >Ultrapure water</td>
			<td >Stakpure</td>
			<td >Omniapure UV 18200002</td>
			<td >to correct for medium evaporation, mixed with aqua stabil mixed and used as hydraulic fluid. (autoclave ultrapure water at step 1)</td>
		</tr>
		<tr >
			<td >UV light</td>
			<td >Philips</td>
			<td >TUV 30W/G30 T8</td>
			<td >for decontamination of grafts and bioreactor parts before seeding</td>
		</tr>
	</tbody>
</table>

a multi-cue bioreactor to evaluate the inflammatory and regenerative capacity of biomaterials under flow and stretch

从转化的角度来看，使用可再吸附生物材料直接在体内诱导再生是一种有吸引力的策略。这种材料在植入时会引起炎症反应，这是随后材料吸收和新组织再生的驱动因素。这一战略，也被称为原位组织工程，旨在获得心血管置换，如组织工程血管移植。炎症和再生过程都由脚手架上的局部生物力学线索（即拉伸和剪切应力）决定。在这里，我们详细描述了定制开发的生物反应器的使用，这种反应器能够使管状脚手架上的拉伸和剪切应力脱钩。这允许系统和标准化地评估管状脚手架在控制良好的机械负载的影响下的炎症和再生能力，我们利用人类巨噬细胞和肌纤维细胞进行动态共培养实验来证明这一点。详细讨论了该方法的关键实际步骤：生物反应器的建造和建立、脚手架和细胞播种的制备、拉伸和剪切流的应用和维护以及样品采集分析。

该生物反应器的开发是为了研究剪切应激和循环拉伸对血管组织生长和3D生物材料脚手架改造的个体和组合效应。生物反应器的设计允许在各种装载条件下培养多达8个血管结构（图1A）。血管结构位于流动培养室（图1B），其中周长伸展和WSS都可以独立控制。流文化室的顶部隔间持有一个流直发器，以相对较短的沉降长度（图1C）?...

Watch this Scientific Journal Video about A Multi-Cue Bioreactor to Evaluate the Inflammatory and Regenerative Capacity of Biomaterials under Flow and Stretch at JoVE.com

A Multi-Cue Bioreactor to Evaluate the Inflammatory and Regenerative Capacity of Biomaterials under Flow and Stretch

本协议的目标是在管状电喷脚手架中执行人类巨噬细胞和肌纤维细胞的动态共生，以研究物质驱动的组织再生，使用生物反应器，使剪切应力和循环拉伸脱钩。

评估流和拉伸下生物材料的炎症和再生能力的多奎生物反应器

The use of resorbable biomaterials to induce regeneration directly in the body is an attractive strategy from a translational perspective. Such materials ...

a-multi-cue-bioreactor-to-evaluate-inflammatory-regenerative-capacity

Research

JoVE Journal

Engineering

5.4K 次观看.  Eindhoven University of Technology. 本协议的目标是在管状电喷脚手架中执行人类巨噬细胞和肌纤维细胞的动态共生，以研究物质驱动的组织再生，使用生物反应器，使剪切应力和循环拉伸脱钩。

视频: A Multi-Cue Bioreactor to Evaluate the Inflammatory and Regenerative Capacity of Biomaterials under Flow and Stretch

Measuring Material Microstructure Under Flow Using 1-2 Plane Flow-Small Angle Neutron Scattering

A new small-angle neutron scattering (SANS) sample environment optimized for studying the microstructure of complex fluids under simple shear flow is presented. The SANS shear cell consists of a concentric cylinder Couette geometry that is sealed and rotating about a horizontal axis so that the vorticity direction of the flow field is aligned with the neutron beam enabling scattering from the 1-2 plane of shear (velocity-velocity gradient, respectively). This approach is an advance over previous shear cell sample environments as there is a strong coupling between the bulk rheology and microstructural features in the 1-2 plane of shear. Flow-instabilities, such as shear banding, can also be studied by spatially resolved measurements. This is accomplished in this sample environment by using a narrow aperture for the neutron beam and scanning along the velocity gradient direction. Time resolved experiments, such as flow start-ups and large amplitude oscillatory shear flow are also possible by synchronization of the shear motion and time-resolved detection of scattered neutrons. Representative results using the methods outlined here demonstrate the useful nature of spatial resolution for measuring the microstructure of a wormlike micelle solution that exhibits shear banding, a phenomenon that can only be investigated by resolving the structure along the velocity gradient direction. Finally, potential improvements to the current design are discussed along with suggestions for supplementary experiments as motivation for future experiments on a broad range of complex fluids in a variety of shear motions.

A shear cell is developed for small-angle neutron scattering measurements in the velocity-velocity gradient plane of shear and is used to characterize complex fluids. Spatially resolved measurements in the velocity gradient direction are possible for studying shear-banding materials. Applications include investigations of colloidal dispersions, polymer solutions, and self-assembled structures.

测量材料在微流使用1-2面流小角中子散射

A new small-angle neutron scattering (SANS) sample environment optimized for studying the microstructure of complex fluids under simple shear flow is ...

科研

工程学

A Testing Platform for Durability Studies of Polymers and Fiber-reinforced Polymer Composites under Concurrent Hygrothermo-mechanical Stimuli

The durability of polymers and fiber-reinforced polymer composites under service condition is a critical aspect to be addressed for their robust designs and condition-based maintenance. These materials are adopted in a wide range of engineering applications, from aircraft and ship structures, to bridges, wind turbine blades, biomaterials and biomedical implants. Polymers are viscoelastic materials, and their response may be highly nonlinear and thus make it challenging to predict and monitor their in-service performance. The laboratory-scale testing platform presented herein assists the investigation of the influence of concurrent mechanical loadings and environmental conditions on these materials. The platform was designed to be low-cost and user-friendly. Its chemically resistant materials make the platform adaptable to studies of chemical degradation due to in-service exposure to fluids. An example of experiment was conducted at RT on closed-cell polyurethane foam samples loaded with a weight corresponding to ~50% of their ultimate static and dry load. Results show that the testing apparatus is appropriate for these studies. Results also highlight the larger vulnerability of the polymer under concurrent loading, based on the higher mid-point displacements and lower residual failure loads. Recommendations are made for additional improvements to the testing apparatus.

The durability of polymers and fiber-reinforced polymer composites in service is a critical aspect for their designs and condition-based maintenance. We present a novel low-cost laboratory testing platform for the investigation of the influence of concurrent mechanical and environmental loadings, and may help design more efficient yet safer composite structures.

一个测试平台为聚合物的耐久性研究，并在同期Hygrothermo机械刺激纤维增强聚合物复合材料

The durability of polymers and fiber-reinforced polymer composites under service condition is a critical aspect to be addressed for their robust designs ...

Experimental Protocol to Investigate Particle Aerosolization of a Product Under Abrasion and Under Environmental Weathering

The present article presents an experimental protocol to investigate particle aerosolization of a product under abrasion and under environmental weathering, which is a fundamental element to the approach of nanosafety-by-design of nanostructured products for their durable development. This approach is basically a preemptive one in which the focus is put on minimizing the emission of engineered nanomaterials' aerosols during the usage phase of the product's life cycle. This can be attained by altering its material properties during its design phase without compromising with any of its added benefits. In this article, an experimental protocol is presented to investigate the nanosafety-by-design of three commercial nanostructured products with respect to their mechanical solicitation and environmental weathering. The means chosen for applying the mechanical solicitation is an abrasion process and for the environmental weathering, it is an accelerated UV exposure in the presence of humidity and heat. The eventual emission of engineered nanomaterials is studied in terms of their number concentration, size distribution, morphology and chemical composition. The purpose of the protocol is to study the emission for test samples and experimental conditions which are corresponding to real life situations. It was found that the application of the mechanical stresses alone emits the engineered nanomaterials' aerosols in which the engineered nanomaterial is always embedded inside the product matrix, thus, a representative product element. In such a case, the emitted aerosols comprise of both nanoparticles as well as microparticles. But if the mechanical stresses are coupled with the environmental weathering, the experimental protocol reveals then the eventual deterioration of the product, after a certain weathering duration, may lead to the emission of the free engineered nanomaterial aerosols too.

In this article, an experimental protocol to investigate particle aerosolization of a product under abrasion and under environmental weathering is presented. Results on the emission of engineered nanomaterials, in the form of aerosols are presented. The specific experimental set-up is described in detail.

实验协议来调查产品的粒子雾化在耐磨和环境下风化

The present article presents an experimental protocol to investigate particle aerosolization of a product under abrasion and under environmental ...

Design and Use of a Full Flow Sampling System (FFS) for the Quantification of Methane Emissions

The use of natural gas continues to grow with increased discovery and production of unconventional shale resources. At the same time, the natural gas industry faces continued scrutiny for methane emissions from across the supply chain, due to methane&#39;s relatively high global warming potential (25-84x that of carbon dioxide, according to the Energy Information Administration). Currently, a variety of techniques of varied uncertainties exists to measure or estimate methane emissions from components or facilities. Currently, only one commercial system is available for quantification of component level emissions and recent reports have highlighted its weaknesses.
In order to improve accuracy and increase measurement flexibility, we have designed, developed, and implemented a novel full flow sampling system (FFS) for quantification of methane emissions and greenhouse gases based on transportation emissions measurement principles. The FFS is a modular system that consists of an explosive-proof blower(s), mass airflow sensor(s) (MAF), thermocouple, sample probe, constant volume sampling pump, laser based greenhouse gas sensor, data acquisition device, and analysis software. Dependent upon the blower and hose configuration employed, the current FFS is able to achieve a flow rate ranging from 40 to 1,500 standard cubic feet per minute (SCFM). Utilization of laser-based sensors mitigates interference from higher hydrocarbons (C2+). Co-measurement of water vapor allows for humidity correction. The system is portable, with multiple configurations for a variety of applications ranging from being carried by a person to being mounted in a hand drawn cart, on-road vehicle bed, or from the bed of utility terrain vehicles (UTVs). The FFS is able to quantify methane emission rates with a relative uncertainty of &#177; 4.4%. The FFS has proven, real world operation for the quantification of methane emissions occurring in conventional and remote facilities.

Design and Use of a Full Flow Sampling System FFS for the Quantification of Methane Emissions

We have designed, developed, and implemented a novel full flow sampling system (FFS) for quantification of methane emissions and greenhouse gases from across the natural gas supply chain.

设计和全流采样系统（FFS）的使用甲烷排放的量化

The use of natural gas continues to grow with increased discovery and production of unconventional shale resources. At the same time, the natural gas ...

A Robotic Platform to Study the Foreflipper of the California Sea Lion

The California sea lion (Zalophus californianus), is an agile and powerful swimmer. Unlike many successful swimmers (dolphins, tuna), they generate most of their thrust with their large foreflippers. This protocol describes a robotic platform designed to study the hydrodynamic performance of the swimming California sea lion (Zalophus californianus). The robot is a model of the animal&#39;s foreflipper that is actuated by motors to replicate the motion of its propulsive stroke (the &#39;clap&#39;). The kinematics of the sea lion&#39;s propulsive stroke are extracted from video data of unmarked, non-research sea lions at the Smithsonian Zoological Park (SNZ). Those data form the basis of the actuation motion of the robotic flipper presented here. The geometry of the robotic flipper is based a on high-resolution laser scan of a foreflipper of an adult female sea lion, scaled to about 60% of the full-scale flipper. The articulated model has three joints, mimicking the elbow, wrist and knuckle joint of the sea lion foreflipper. The robotic platform matches dynamics properties&#8212;Reynolds number and tip speed&#8212;of the animal when accelerating from rest. The robotic flipper can be used to determine the performance (forces and torques) and resulting flowfields.

A robotic platform is described that will be used to study the hydrodynamic performance&#8212;forces and flowfields&#8212;of the swimming California sea lion. The robot is a model of the animal&#39;s foreflipper that is actuated by motors to replicate the motion of its propulsive stroke (the &#39;clap&#39;).

机器人平台研究加州海狮的Foreflipper

The California sea lion (Zalophus californianus), is an agile and powerful swimmer. Unlike many successful swimmers (dolphins, tuna), they generate most ...

Solvent Bonding for Fabrication of PMMA and COP Microfluidic Devices

Thermoplastic microfluidic devices offer many advantages over those made from silicone elastomers, but bonding procedures must be developed for each thermoplastic of interest. Solvent bonding is a simple and versatile method that can be used to fabricate devices from a variety of plastics. An appropriate solvent is added between two device layers to be bonded, and heat and pressure are applied to the device to facilitate the bonding. By using an appropriate combination of solvent, plastic, heat, and pressure, the device can be sealed with a high quality bond, characterized as having high bond coverage, bond strength, optical clarity, durability over time, and low deformation or damage to microfeature geometry. We describe the procedure for bonding devices made from two popular thermoplastics, poly(methyl-methacrylate) (PMMA), and cyclo-olefin polymer (COP), as well as a variety of methods to characterize the quality of the resulting bonds, and strategies to troubleshoot low quality bonds. These methods can be used to develop new solvent bonding protocols for other plastic-solvent systems.

Solvent bonding is a simple and versatile method for fabricating thermoplastic microfluidic devices with high quality bonds. We describe a protocol to achieve strong, optically clear bonds in PMMA and COP microfluidic devices that preserve microfeature details, by a judicious combination of pressure, temperature, an appropriate solvent, and device geometry.

溶剂粘接的PMMA的制备和COP微流体装置

Thermoplastic microfluidic devices offer many advantages over those made from silicone elastomers, but bonding procedures must be developed for each ...

In Situ Visualization of the Phase Behavior of Oil Samples Under Refinery Process Conditions

To help address production issues in refineries caused by the fouling of process units and lines, we have developed a setup as well as a method to visualize the behavior of petroleum samples under process conditions. The experimental setup relies on a custom-built micro-reactor fitted with a sapphire window at the bottom, which is placed over the objective of an inverted microscope equipped with a cross-polarizer module. Using reflection microscopy enables the visualization of opaque samples, such as petroleum vacuum residues, or asphaltenes. The combination of the sapphire window from the micro-reactor with the cross-polarizer module of the microscope on the light path allows high-contrast imaging of isotropic and anisotropic media. While observations are carried out, the micro-reactor can be heated to the temperature range of cracking reactions (up to 450 &#176;C), can be subjected to H2 pressure relevant to hydroconversion reactions (up to 16 MPa), and can stir the sample by magnetic coupling. 
Observations are typically carried out by taking snapshots of the sample under cross-polarized light at regular time intervals. Image analyses may not only provide information on the temperature, pressure, and reactive conditions yielding phase separation, but may also give an estimate of the evolution of the chemical (absorption/reflection spectra) and physical (refractive index) properties of the sample before the onset of phase separation.

In Situ Visualization of the Phase Behavior of Oil Samples Under Refinery Process Conditions

This article describes a setup and method for the in situ visualization of oil samples under a variety of temperature and pressure conditions that aim to emulate refining and upgrading processes. It is primarily used for studying isotropic and anisotropic media involved in the fouling behavior of petroleum feeds.

在油样品的相行为在炼油工艺条件的原位可视化

To help address production issues in refineries caused by the fouling of process units and lines, we have developed a setup as well as a method to ...

Scanning Light Scattering Profiler (SLPS) Based Methodology to Quantitatively Evaluate Forward and Backward Light Scattering from Intraocular Lenses

The scanning light scattering profiler (SLSP) methodology has been developed for the full-angle quantitative evaluation of forward and backward light scattering from intraocular lenses (IOLs) using goniophotometer principles. This protocol describes the SLSP platform and how it employs a 360&#176; rotational photodetector sensor that is scanned around an IOL sample while recording the intensity and location of scattered light as it passes through the IOL medium. The SLSP platform can be used to predict, non-clinically, the propensity for current and novel IOL designs and materials to induce light scatter. Non-clinical evaluation of light scattering properties of IOLs can significantly reduce the number of patient complaints related to unwanted glare, glistening, optical defects, poor image quality, and other phenomena associated with the unintended light scattering. Future studies should be conducted to correlate SLSP data with clinical results to help identify which measured light scatter is most problematic for patients that have undergone cataract surgery subsequent to IOL implantation.

Scanning Light Scattering Profiler SLPS Based Methodology to Quantitatively Evaluate Forward and Backward Light Scattering from Intraocular Lenses

This protocol describes the scanning light scattering profiler (SLSP) that enables the full-angle quantitative evaluation of forward and backward scattering of light from intraocular lenses (IOLs) using goniophotometer principles.

基于扫描光散射分析器（SLPS）的方法来量化评估来自眼内镜的前向和后向光散射

The scanning light scattering profiler (SLSP) methodology has been developed for the full-angle quantitative evaluation of forward and backward light ...

A Novel Biaxial Testing Apparatus for the Determination of Forming Limit under Hot Stamping Conditions

The hot stamping and cold die quenching process is increasingly used to form complex shaped structural components of sheet metals. Conventional experimental approaches, such as out-of-plane and in-plane tests, are not applicable to the determination of forming limits when heating and rapid cooling processes are introduced prior to forming for tests conducted under hot stamping conditions. A novel in-plane biaxial testing system was designed and used for the determination of forming limits of sheet metals at various strain paths, temperatures, and strain rates after heating and cooling processes in a resistance heating uniaxial testing machine. The core part of the biaxial testing system is a biaxial apparatus, which transfers a uniaxial force provided by the uniaxial testing machine to a biaxial force. One type of cruciform specimen was designed and verified for the formability test of aluminum alloy 6082 using the proposed biaxial testing system. The digital image correlation (DIC) system with a high-speed camera was used for taking strain measurements of a specimen during a deformation. The aim of proposing this biaxial testing system is to enable the forming limits of an alloy to be determined at various temperatures and strain rates under hot stamping conditions.

This protocol proposes a novel biaxial testing system used on a resistance heating uniaxial tensile test machine in order to determine the forming limit diagram (FLD) of sheet metals under hot stamping conditions.

一种新型双轴试验设备的成形极限的下烫印条件的决定

The hot stamping and cold die quenching process is increasingly used to form complex shaped structural components of sheet metals. Conventional ...

Microfluidic Imaging Flow Cytometry by Asymmetric-detection Time-stretch Optical Microscopy (ATOM)

Scaling the number of measurable parameters, which allows for multidimensional data analysis and thus higher-confidence statistical results, has been the main trend in the advanced development of flow cytometry. Notably, adding high-resolution imaging capabilities allows for the complex morphological analysis of cellular/sub-cellular structures. This is not possible with standard flow cytometers. However, it is valuable for advancing our knowledge of cellular functions and can benefit life science research, clinical diagnostics, and environmental monitoring. Incorporating imaging capabilities into flow cytometry compromises the assay throughput, primarily due to the limitations on speed and sensitivity in the camera technologies. To overcome this speed or throughput challenge facing imaging flow cytometry while preserving the image quality, asymmetric-detection time-stretch optical microscopy (ATOM) has been demonstrated to enable high-contrast, single-cell imaging with sub-cellular resolution, at an imaging throughput as high as 100,000 cells/s. Based on the imaging concept of conventional time-stretch imaging, which relies on all-optical image encoding and retrieval through the use of ultrafast broadband laser pulses, ATOM further advances imaging performance by enhancing the image contrast of unlabeled/unstained cells. This is achieved by accessing the phase-gradient information of the cells, which is spectrally encoded into single-shot broadband pulses. Hence, ATOM is particularly advantageous in high-throughput measurements of single-cell morphology and texture &#8211; information indicative of cell types, states, and even functions. Ultimately, this could become a powerful imaging flow cytometry platform for the biophysical phenotyping of cells, complementing the current state-of-the-art biochemical-marker-based cellular assay. This work describes a protocol to establish the key modules of an ATOM system (from optical frontend to data processing and visualization backend), as well as the workflow of imaging flow cytometry based on ATOM, using human cells and micro-algae as the examples.

Microfluidic Imaging Flow Cytometry by Asymmetric-detection Time-stretch Optical Microscopy ATOM

This protocol describes the implementation of an asymmetric-detection time-stretch optical microscopy system for single-cell imaging in ultrafast microfluidic flow and its applications in imaging flow cytometry.

微流控成像流式细胞仪通过不对称检测时间延伸光学显微镜（ATOM）

Scaling the number of measurable parameters, which allows for multidimensional data analysis and thus higher-confidence statistical results, has been the ...