use-capillary-aerosol-generator-continuous-production-controlled

Use of Capillary Aerosol Generator in Continuous Production of Controlled Aerosol for Non-Clinical Studies

The capillary aerosol generator (CAG) is operated with the principal of thermal liquid evaporation through heating of e-liquid in the initial phase, ...

Philip Morris Products S.A.

Chemical and physical characterization of transported evolving aerosols in an  system is complex. The challenges include appropriate sampling sensitivity, measurement capabilities, and performing online measurements of constituents in the flowing aerosol during exposure. We assessed the performance of single-photon ionization mass spectrometry in measuring aerosol properties within an  aerosol exposure system. The sampling efficiency of the instrument was studied under three protocols to capture the evolving aerosol process inside the exposure system, and it was evaluated using computational fluid dynamics modeling. The changes in the aerosol as dilution is applied show not only a reduction in concentration of the traced substances but also selective sampling due to evolution of the aerosol and (gas/liquid) phase partitioning of the substances forming the aerosol or a change in the aerosol properties. These effects have potentially a direct impact on the delivered dose, as aerosol deposition is dependent on particle size. Dilution affects the chemical concentration of the substances as well as the interconnected physical properties of the aerosol; therefore, the experimental design of  studies should not only report the dilution flow rates but also details of the applied dilution protocol. This adds a layer of complexity to the design and comparison of studies. We also discuss the potential and limitations of single-photon ionization mass spectrometry as a tool in  monitoring of aerosols.

Assessment of Single-Photon Ionization Mass Spectrometry for Online Monitoring of  Aerosol Exposure Experiments.

Accurately determining the delivered dose is critical to understanding biological response due to cell exposure to chemical constituents in aerosols. Deposition efficiency and uniformity of deposition was measured experimentally using monodisperse solid fluorescent particles with mass median aerodynamic diameters (MMAD) of 0.51, 1.1, 2.2 and 3.3 μm in the Vitrocell® AMES 48 air-liquid-interface (ALI) in vitro exposure system. Experimental results were compared with computational fluid dynamic, (CFD; using both Lagrangian and Eulerian approaches) predicted deposition efficiency and uniformity for a single row (N = 6) of petri dishes in the Vitrocell® AMES 48 system. The average experimentally measured deposition efficiency ranged from 0.007% to 0.43% for 0.51-3.3 μm MMAD particles, respectively. There was good agreement between average experimentally measured and the CFD predicted particle deposition efficiency, regardless of approach. Experimentally measured and CFD predicted average uniformity of deposition was greater than 45% of the mean for all particle diameters. During this work a new design was introduced by the manufacturer and evaluated using Lagragian CFD. Lagragian CFD predictions showed better uniformity of deposition, but reduced deposition efficiency with the new design. Deposition efficiency and variability in particle deposition across petri dishes for solid particles should be considered when designing exposure regimens using the Vitrocell® AMES 48 ALI in vitro exposure system.

Comparison of experimentally measured and computational fluid dynamic predicted deposition and deposition uniformity of monodisperse solid particles in the Vitrocell® AMES 48 air-liquid-interface in-vitro exposure system.

Cigarette smoking is one major modifiable risk factor in the development and progression of chronic obstructive pulmonary disease and cardiovascular disease. To characterize and compare cigarette smoke (CS)-induced disease endpoints after exposure in either whole-body (WB) or nose-only (NO) exposure systems, we exposed apolipoprotein E-deficient mice to filtered air (Sham) or to the same total particulate matter (TPM) concentration of mainstream smoke from 3R4F reference cigarettes in NO or WB exposure chambers (EC) for 2 months. At matching TPM concentrations, we observed similar concentrations of carbon monoxide, acetaldehyde, and acrolein, but higher concentrations of nicotine and formaldehyde in NOEC than in WBEC. In both exposure systems, CS exposure led to the expected adaptive changes in nasal epithelia, altered lung function, lung inflammation, and pronounced changes in the nasal epithelial transcriptome and lung proteome. Exposure in the NOEC caused generally more severe histopathological changes in the nasal epithelia and a higher stress response as indicated by body weight decrease and lower blood lymphocyte counts compared with WB exposed mice. Erythropoiesis, and increases in total plasma triglyceride levels and atherosclerotic plaque area were observed only in CS-exposed mice in the WBEC group but not in the NOEC group. Although the composition of CS in the breathing zone is not completely comparable in the two exposure systems, the CS-induced respiratory disease endpoints were largely confirmed in both systems, with a higher magnitude of severity after NO exposure. CS-accelerated atherosclerosis and other pro-atherosclerotic factors were only significant in WBEC.

Impact of whole-body versus nose-only inhalation exposure systems on systemic, respiratory, and cardiovascular endpoints in a 2-month cigarette smoke exposure study in the ApoE mouse model.

Francesco Lucci

PMI R&D

Philip Morris Products S.A.

Use of Capillary Aerosol Generator in Continuous Production of Controlled Aerosol for Non-Clinical Studies

Francesco Lucci

.css-o250i3{font-size:18px;font-family:Open Sans,sans-serif;line-height:21.6px;}PMI R&D

Philip Morris Products S.A.

Use of Capillary Aerosol Generator in Continuous Production of Controlled Aerosol for Non-Clinical Studies

PMI R&D